This paper demonstrates the use of Universal Software Radio Peripheral (USRP), together with Raspberry Pi3 B+ (RP3) as the brain (or the decision making engine), to develop a distributed wireless network in which nodes can communicate with other nodes independently and make decision autonomously. In other words, each USRP node (i.e., sensor) is embedded with separate processing units (i.e., RP3), which has not been investigated in the literature, so that each node can make independent decisions in a distributed manner. The proposed testbed in this paper is compared with the traditional distributed testbed, which has been widely used in the literature. In the traditional distributed testbed, there is a single processing unit (i.e., a personal computer) that makes decisions in a centralized manner, and each node (i.e., USRP) is connected to the processing unit via a switch. The single processing unit exchanges control messages with nodes via the switch, while the nodes exchange data packets among themselves using a wireless medium in a distributed manner. The main disadvantage of the traditional testbed is that, despite the network being distributed in nature, decisions are made in a centralized manner. Hence, the response delay of the control message exchange is always neglected. The use of such testbed is mainly due to the limited hardware and monetary cost to acquire a separate processing unit for each node. The experiment in our testbed has shown the increase of end-to-end delay and decrease of packet delivery ratio due to software and hardware delays. The observed multihop transmission is performed using device-to-device (D2D) communication, which has been enabled in 5G. Therefore, nodes can either communicate with other nodes via: (a) a direct communication with the base station at the macrocell, which helps to improve network performance; or (b) D2D that improve spectrum efficiency, whereby traffic is offloaded from macrocell to small cells. Our testbed is the first of its kind in this scale, and it uses RP3 as the distributed decision-making engine incorporated into the USRP/GNU radio platform. This work provides an insight to the development of a 5G network.
The feasibility of using a computer database management system based on an 8·bit microcomputer for storing, retrieving and analysing patient data in a limited setting (oesophago·gastro-duodenoscopy records from a peripheral general surgical department over a 1 year period) is presented. A program developed by the author was used to enter the relevant records of 208 patients undergoing the above examination, and to retrieve and analyse any desired data. Compatible statistical and graphics software packages can be used to access and analyse the data and display or print out the results. The limitations and scope for further expansion of the system are discussed.
We describe the design and management of a 35 mm slide database using a menu-driven dBASE III PLUS programme and a microcomputer in a large department of pathology that also caters for the individual pathologist. Existing systems described in the literature are geared towards slides of general medicine and do not address the needs of the individual pathologist. A total of 11,481 slides in the Department of Pathology, Faculty of Medicine, University of Malaya, were filed into a single database with each record representing one slide. Nine fields which comprised the slide accession number, reference number, slide category, SNOMED codes, and a description of the slide in natural language, seemed adequate for slide definition. The menu-driven programme had functions which included the abilities to add, delete, edit and back-up records, and to search for desired slides. Although slides may be searched for in various fields, we found that searches using natural language alone were both comprehensive and efficient, provided a standard format of description was adhered to and data entries scrutinized carefully for errors. We believe therefore, that for the pathologist working alone, coded language fields are not absolutely necessary, as manual coding and additional data entry can be time consuming. As expected, for databases larger than 10,000 slides, a 80286 microprocessor-based microcomputer was more efficient. We are of the opinion that a system such as ours is very useful for a large department of pathology or the individual pathologist to file and retrieve 35 mm slides.
An earlier electrochemical mechanism of DNA detection was adapted and specified for the detection of Vibrio parahaemolyticus in real samples. The reader, based on a screen printed carbon electrode, was modified with polylactide-stabilized gold nanoparticles and methylene blue was employed as the redox indicator. Detection was assessed using a microprocessor to measure current response under controlled potential. The fabricated sensor was able to specifically distinguish complementary, non-complementary and mismatched oligonucleotides. DNA was measured in the range of 2.0 × 10(-8)-2.0 × 10(-13) M with a detection limit of 2.16 pM. The relative standard deviation for 6 replications of differential pulse voltammetry (DPV) measurement of 0.2 µM complementary DNA was 4.33%. Additionally, cross-reactivity studies against various other food-borne pathogens showed a reliably sensitive detection of the target pathogen. Successful identification of Vibrio parahaemolyticus (spiked and unspiked) in fresh cockles, combined with its simplicity and portability demonstrate the potential of the device as a practical screening tool.
The use of a personal computer together with a Data Acquisition System (DAQ) as the processing tool in optical tomography systems has been the norm ever since the beginning of process tomography. However, advancements in silicon fabrication technology allow nowadays the fabrication of powerful Digital Signal Processors (DSP) at a reasonable cost. This allows this technology to be used in an optical tomography system since data acquisition and processing can be performed within the DSP. Thus, the dependency on a personal computer and a DAQ to sample and process the external signals can be reduced or even eliminated. The DSP system was customized to control the data acquisition process of 16x16 optical sensor array, arranged in parallel beam projection. The data collected was used to reconstruct the cross sectional image of the pipeline conveyor. For image display purposes, the reconstructed image was sent to a personal computer via serial communication. This allows the use of a laptop to display the tomogram image besides performing any other offline analysis.
In the past, simulating charge dynamics in solid state devices, such as current mobility, transient current drift velocities are done on mainframe systems or on high performance computing facilities. This is due to the fact that, such simulations are costly in terms of computational requirements when implemented on a single processor-based personal computers (PCs). When simulating charge dynamics, large ensembles of particles are usually preferred, such as exceeding 40000 particles, to ensure a numerically sound result. When implementing this type of simulation on a single processor PCs using the conventional ensemble or single particle Monte Carlo method, the computational time is very long even on the fast 2.0 MHz PCs. Lately, a more efficient, easily made available tools and cost effective solution to this problem is the application of an array of PCs employed in a parallel application. This is done using a computer cluster network in a master-slave model. In this paper we report the development of a LINUX cluster for the purpose of implementing parallel ensemble Monte Carlo modelling for solid states device. We have proposed the use of Parallel Virtual Machine (PVM) standards when running the parallel algorithm of the ensemble MC simulation. Some results of the development are also presented in this paper.
This procedure is easy to use and is cost-effective because it uses equipment that exist in any office or institution. The material used, transparency film for use with plain paper copier, is less expensive than either photographic slide film or normal slide films. Moreover, the transparency sheet can be used again for photocopying until the sheet is fully used up. There is no added cost of development of film, or is it necessary to wait for the whole roll of film to be used before the label can be retrieved and used. The background of the label is clear and only the black images of the characters of the label can be clearly seen. The effect of the transparency film, photocopy ink, and adhesive glue is not known. But no adverse effects have been noted. Microlabels have advantages over conventional labels with characters in font size 8 to 12, because more information, such as the full name of the patient, sex, country of origin, and national identification number can be incorporated. With more detailed information, quick identification of a deceased person can be made. Microlabels with a clear background will have minimal esthetic impact on the patient. The disadvantages of the technique is that it may not withstand a fire. In situations where the deceased body is badly burned, the denture and its identification strip may be burned, too. However, this risk can be minimized by placing the strip in the most posterior part of the denture-palatal in the maxillary denture and distal lingual in the mandibular denture. For testing of durability, dentures with the labels were placed in water for up to 4 months. The labels showed no sign of fading or deterioration.
This article describes the design of a robust, inexpensive, easy-to-use, small, and portable online electromyography acquisition system for monitoring electromyography signals during rehabilitation. This single-channel (one-muscle) system was connected via the universal serial bus port to a programmable Windows operating system handheld tablet personal computer for storage and analysis of the data by the end user. The raw electromyography signals were amplified in order to convert them to an observable scale. The inherent noise of 50 Hz (Malaysia) from power lines electromagnetic interference was then eliminated using a single-hybrid IC notch filter. These signals were sampled by a signal processing module and converted into 24-bit digital data. An algorithm was developed and programmed to transmit the digital data to the computer, where it was reassembled and displayed in the computer using software. Finally, the following device was furnished with the graphical user interface to display the online muscle strength streaming signal in a handheld tablet personal computer. This battery-operated system was tested on the biceps brachii muscles of 20 healthy subjects, and the results were compared to those obtained with a commercial single-channel (one-muscle) electromyography acquisition system. The results obtained using the developed device when compared to those obtained from a commercially available physiological signal monitoring system for activities involving muscle contractions were found to be comparable (the comparison of various statistical parameters) between male and female subjects. In addition, the key advantage of this developed system over the conventional desktop personal computer-based acquisition systems is its portability due to the use of a tablet personal computer in which the results are accessible graphically as well as stored in text (comma-separated value) form.
Data transmission in field works especially that is related to industry, gas and chemical is paramount importance to ensure data accuracy and delivery time. A development of wireless detector system for remote data acquisition to be applied in conducting fieldwork in industry is described in this paper. A wireless communication which is applied in the project development is a viable and cost-effective method of transmitting data from the detector to the laptop on the site to facilitate data storage and analysis automatically, which can be used in various applications such as column scanning. The project involves hardware design for the detector and electronics parts besides programming for control board and user interface. A prototype of a wireless gamma scintillation detector is developed with capabilities of transmitting data to computer via radio frequency (RF) and recording the data within the 433MHz band at baud rate of 19200.
An ergonomics improvement study was conducted on the visual inspection process of a printed circuit assembly (PCA) factory. The process was studied through subjective assessment and direct observation. Three problems were identified: operators' eye problems, insufficient time for inspection and ineffective visual inspection. These problems caused a huge yearly rejection cost of US 298,240 dollars, poor quality, customer dissatisfaction and poor occupational health and safety. Ergonomics interventions were made to rectify the problems: reduced usage of a magnifying glass, the use of less glaring inspection templates, inspection of only electrically non-tested components and introduction of a visual inspection sequence. The interventions produced savings in rejection cost, reduced operators' eye strain, headaches and watery eyes, lowered the defect percentage at customers' sites and increased the factory's productivity and customer satisfaction.
Purpose of the study: The objective of this study was to investigate the existence of the golden proportion between the width of the maxillary anterior teeth of undergraduate dental students at University of Malaya. Materials and method: Standardised photographs of 100 dental students’ smiles displaying only the lips and the teeth were captured. The images were transferred to a personal computer and the width of the maxillary anterior teeth was measured using an Image
Analyzer (Leiqa QWin). Calculations were made according to the Theory of Golden Proportion. The
data were statistically analysed using paired student T-test (α
The low resolution Automatic Picture Transmission (APT) data from the National Oceanic and Atmospheric Administration (NOAA) polar-orbiting satellites Advanced Very High Resolution Radiometer (AVHRR) is being received and recorded in real-time mode at ground receiving station in School of Science and Technology, Universiti Malaysia Sabah. The system is suitable for the developing and undeveloped countries in south and Southeast Asia and is said to be acceptable for engineering, agricultural, climatological and environmental applications. The system comprises a personal computer attached with a small APT receiver. The data transmission between the ground receiving station and NOAA satellites is using the electromagnetic wave. The relation for receiving and processing the electromagnetic wave in the transmission will be discussed.
Audio forgery is any act of tampering, illegal copy and fake quality in the audio in a criminal way. In the last decade, there has been increasing attention to the audio forgery detection due to a significant increase in the number of forge in different type of audio. There are a number of methods for forgery detection, which electric network frequency (ENF) is one of the powerful methods in this area for forgery detection in terms of accuracy. In spite of suitable accuracy of ENF in a majority of plug-in powered devices, the weak accuracy of ENF in audio forgery detection for battery-powered devices, especially in laptop and mobile phone, can be consider as one of the main obstacles of the ENF. To solve the ENF problem in terms of accuracy in battery-powered devices, a combination method of ENF and phase feature is proposed. From experiment conducted, ENF alone give 50% and 60% accuracy for forgery detection in mobile phone and laptop respectively, while the proposed method shows 88% and 92% accuracy respectively, for forgery detection in battery-powered devices. The results lead to higher accuracy for forgery detection with the combination of ENF and phase feature.
A cross-sectional study of medical students using a self-administered questionnaire was carried out in the Faculty of Medicine, University of Malaya, Malaysia from December 2000 to January 2001 to determine IT usage, perceptions and literacy of medical students. 366 of 653 (56.0%) students reported owning some type of personal computer. Students mainly used the computer to get onto the Internet, do word-processing and make presentations. Junior (Year One and Two) students and those who had used computers before entering university were more likely to use the Internet. Those who own computers were more likely to feel comfortable with software (OR 1.61, 95% CI: 1.09, 2.38). Students who use the Internet were more likely to perceive that IT facilitated their studies (OR 4.61, 95% CI: 2.35, 9.05). The highest self-reported IT skill was e-mailing followed by surfing the World Wide Web and word-processing. Male students and junior students had significantly higher self-reported IT literacy scores compared to female students and senior students. Significant predictors for an IT identifier score after adjusting for other variables were self-reported rating of computer knowledge, number of siblings, parents' income and gender.
The last 20 years have seen a tremendous growth in mobile computing and wireless communications and services. An experimental study was conducted to explore the effect of text/background color on a laptop computing system along with variable environmental vibration on operators' data entry task performance in moving automobiles. The operators' performance was measured in terms of the number of characters entered per minute without spaces (NCEPMWS) on a laptop computing system. The subjects were divided into 3 categories, namely, Novices, Intermediates and Experts. Findings suggest a re-evaluation of existing laptop designs taking ergonomics into consideration. It appears that proper selection of text/background color on the laptop coupled with controlled vehicular speed could result in a better quality of interaction between human and laptops and it could also resolve the problem of poor data entry task performance.
The last 20 years have seen a tremendous growth in the field of computing with special reference to mobile computing. Ergonomic issues pertaining to this theme remains unexplored. With special reference to readability in mobile computing, an experimental research was conducted to study the gender effect on human performance under the impact of vibration in a human computer interaction environment. Fourteen subjects (7 males and 7 females) participated in the study. Three independent variables, namely gender, level of vibration and screen text/background colour, were selected for the experimental investigation while the dependent variable was the number of characters read per minute. The data collected were analyzed statistically through an experimental design for repeated measures. Results indicated that gender as an organismic variable, the level of vibration and screen text/background colour revealed statistically significant differences. However, the second order interaction was found to be statistically non-significant. These findings are discussed in light of the previous studies undertaken on the topic.
The third and final meeting of a coordinated research programme on the diagnosis and management of thyroid disorders was held in Vienna from 15 to 17 December 1986. The participants were from Czechoslovakia, Egypt, Israel, Malaysia and Thailand. Each participant had studied between 500 and 1000 patients for thyroid function evaluation by performing T3, T4 and TSH radioimmunoassays. Each had also used the newly available supersensitive immunoradiometric (IRMA) assay in a group of patients to compare the efficiency of the new assay with that of the conventional assay. A microcomputer was provided to each participant for data analysis. Internal quality control was studied by establishing precision profiles and external quality control was on the basis of pooled standard sera in different ranges. Recommendation for the strategy suggested T4 RIA as the test of first choice in each category of thyroid function. IRMA TSH was suggested as a second test in borderline cases.