Response surface methodology (RSM) was used to optimize the concentrations of chitosan and glycerol for coating Berangan banana (Musa sapientum cv. Berangan). The effects of main edible coating components, chitosan (0.5-2.5%, w/w) and glycerol (0-2%, w/w) on weight loss, firmness, total colour difference, total soluble solids content (TSS) and titratable acidity (TA) of coated banana were studied during 10 days of storage at 26±2°C and 40-50% relative humidity. Results showed that the experimental data could be adequately fitted into a second-order polynomial model with coefficient of determination (R 2 ) ranging from 0.745 to 0.930 for all the variables studied. In general, the chitosan concentration appeared to be the most significant (P< 0.1) factor influencing all variables except for TSS. The optimum concentration of chitosan and glycerol were predicted to be 2.02% and 0.18%, respectively. Statistical assessment showed insignificant difference between experimental and predicted values.
Muslim consumers have special needs in medical treatment that differ from non-Muslim consumers. In particular, there is a growing demand among Muslim consumers for Halal medications. This descriptive exploratory study aims to determine the Halal status of selected cardiovascular, endocrine, and respiratory medications stored in an out-patient pharmacy in a Malaysian governmental hospital. Sources of active ingredients and excipients for each product were assessed for Halal status based on available information obtained from product leaflets, the Medical Information Management System (MIMS) website, or manufacturers. Halal status was based on the products' sources and categorized into Halal, Mushbooh, or Haram. The proportions of Halal, Mushbooh, and Haram products were at 19.1%, 57.1%, and 23.8%, respectively. The percentage of active ingredients for cardiovascular/endocrine products that were assessed as Haram was 5.3%; for respiratory medications, it was only 1.1%. For excipients, 1.7% and 4.8% fall under the category of Haram for cardiovascular/endocrine products and respiratory products, respectively. Ethanol and magnesium stearate were found to be the common substances that were categorized as Haram and Mushbooh.
Citric acid (CA) can be found naturally in fruits and vegetables, particularly citrus fruit. CA is widely used in many fields but its usage as a green modifying agent and binder for wood is barely addressed. Esterification is one of the most common chemical reactions applied in wood modification. CA contains three carboxyl groups, making it possible to attain at least two esterification reactions that are required for crosslinking when reacting with the hydroxyl groups of the cell wall polymers. In addition, the reaction could form ester linkages to bring adhesivity and good bonding characteristics, and therefore CA could be used as wood binder too. This paper presents a review concerning the usage of CA as a wood modifying agent and binder. For wood modification, the reaction mechanism between wood and CA and the pros and cons of using CA are discussed. CA and its combination with various reactants and their respective optimum parameters are also compiled in this paper. As for the major wood bonding component, the bonding mechanism and types of wood composites bonded with CA are presented. The best working conditions for the CA in the fabrication of wood-based panels are discussed. In addition, the environmental impacts and future outlook of CA-treated wood and bonded composite are also considered.
This study was carried out to determine the proximate, functional and pasting properties of breadfruit starch. Breadfruit starch was isolated from matured breadfruit (Artocarpus altilis) and was analyzed for its fuctional, proximate and pasting properties. The starch contains 10.83%, 0.53%, 0.39%, 22.52%, 77.48% and 1.77% moisture, crude protein, fat, amylose, amylopectin and ash contents respectively. The average particle size, pH, bulk density and dispersibility of the breadfruit starch were 18 μm, 6.5, 0.673 g/mls, and 40.67% respectively. The swelling power of the breadfruit starch increases with increase in temperature, but there was a rapid increase in the swelling power from 70 to 80 0C. The pasting temperature of the starch paste was 84.05 0C, setback and breakdown values were 40.08 and 7.92 RVU respectively. The peak viscosity value was 121.25 RVU while final viscosity value was 153.42 RVU. This study concluded that breadfruit starch has an array of functional, pasting and proximate properties that can facilitate its use in so many areas where the properties of other starches are acceptable.
Zinc (Zn) was identified as one of the most toxic heavy metals and often found contaminating the water sources as a result of inefficient treatment of industrial effluent. A green emulsion liquid membrane (GELM) was proposed in this study as a method to minimize the concentration of Zn ions in an aqueous solution. Instead of the common petroleum-based diluent, the emulsion is reformulated with untreated waste cooking oil (WCO) collected from the food industry as a sustainable and cheaper diluent. It also includes Bis(2-ethylhexyl) phosphate (D2EHPA) as a carrier, Span 80 as a surfactant, sulfuric acid (H2SO4) as an internal phase, and ZnSO4 solution as an external phase. Such formulation requires a thorough understanding of the oil characteristics as well as the interaction of the components in the membrane phase. The compatibility of WCO and D2EHPA, as well as the external phase pH, was confirmed via a liquid-liquid extraction (LLE) method. To obtain the best operating conditions for Zn extraction using GELM, the extraction time and speed, carrier, surfactant and internal phase concentrations, and W/O ratio were varied. 95.17% of Zn ions were removed under the following conditions; 0.001 M of H2SO4 in external phase, 700 rpm extraction speed for 10 min, 8 wt% of carrier and 4 wt% of surfactant concentrations, 1:4 of W/O ratio, and 1 M of internal phase concentration.
The synergistic effect of using κ-carrageenan bionanocomposites with the hybridization of cellulose nanocrystals (CNCs) and organically modified montmorillonite (OMMT) reinforcements was studied. The effects of different reinforcements and filler contents were evaluated through mechanical testing, and morphological and water uptake properties. The tensile strength and Young's modulus of both bionanocomposites increased with filler loading and optimized at 4%. OMMT incorporation into the κ-carrageenan/CNCs bionanocomposites resulted in further mechanical property improvement with an optimum ratio of 1:1 (CNCs:OMMT) while maintaining high film transparency. X-ray diffraction and morphological analyses revealed that intercalation occurred between the κ-carrageenan bionanocomposite matrix and OMMT. The water uptake of the κ-carrageenan bionanocomposites was significantly reduced by the addition of both CNCs and OMMT. The enhancements in the mechanical properties and performance of the hybrid bionanocomposite indicate compatibility among the reinforcement, biopolymer, and well-dispersed nanoparticles. This renders the hybrid CNC/OMMT/κ-carrageenan nanocomposites extremely promising for food packaging applications.
In recent years, there has been considerable interest in the use of natural fibers as potential reinforcing fillers in polymer composites despite their hydrophilicity, which limits their widespread commercial application. The present study explored the fabrication of nanocomposites by melt mixing, using an internal mixer followed by a compression molding technique, and incorporating rice husk (RH) as a renewable natural filler, montmorillonite (MMT) nanoclay as water-resistant reinforcing nanoparticles, and polypropylene-grafted maleic anhydride (PP-g-MAH) as a compatibilizing agent. To correlate the effect of MMT delamination and MMT/RH dispersion in the composites, the mechanical and thermal properties of the composites were studied. XRD analysis revealed delamination of MMT platelets due to an increase in their interlayer spacing, and SEM micrographs indicated improved dispersion of the filler(s) from the use of compatibilizers. The mechanical properties were improved by the incorporation of MMT into the PP/RH system and the reinforcing effect was remarkable as a result of the use of compatibilizing agent. Prolonged water exposure of the prepared samples decreased their tensile and flexural properties. Interestingly, the maximum decrease was observed for PP/RH composites and the minimum was for MMT-reinforced and PP-g-MAH-compatibilized PP/RH composites. DSC results revealed an increase in crystallinity with the addition of filler(s), while the melting and crystallization temperatures remained unaltered. TGA revealed that MMT addition and its delamination in the composite systems improved the thermal stability of the developed nanocomposites. Overall, we conclude that MMT nanoclay is an effective water-resistant reinforcing nanoparticle that enhances the durability, mechanical properties, and thermal stability of composites.
Ondansetron tablets that are directly compressed using crospovidone and croscarmellose as a synthetic super disintegrant are the subject of this investigation. A central composite, response surface, randomly quadratic, nonblock (version 13.0.9.0) 32 factorial design is used to optimize the formulation (two-factor three-level). To make things even more complicated, nine different formulation batches (designated as F1-F9) were created. There were three levels of crospovidone and croscarmellose (+1, 0, -1). In addition to that, pre- and postcompressional parameters were evaluated, and all evaluated parameters were found to be within acceptable range. Among all postcompressional parameter dispersion and disintegration time, in vitro drug release experiments (to quantify the amount of medication released from the tablet) and their percentage prediction error were shown to have a significant influence on three dependent variables. Various pre- and postcompression characteristics of each active component were tested in vitro. Bulk density, tap density, angle of repose, Carr's index, and the Hausner ratio were all included in this analysis, as were many others. This tablet's hardness and friability were also assessed along with its dimension and weight variations. Additional stability studies may be conducted using the best batch of the product. For this study, we utilised the Design-Expert software to select the formulation F6, which had dispersion times of 17.67 ± 0.03 seconds, disintegration times of 120.12 ± 0.55 seconds, and percentage drug release measurements of 99.25 ± 0.36 within 30 minutes. Predicted values and experimental data had a strong correlation. Fast dissolving pills of ondansetron hydrochloride may be created by compressing the tablets directly.
The objective of this study was to evaluate the effects of milling methods on tensile properties of polypropylene (PP) / oil palm mesocarp fibre (OPMF) biocomposites. Two types of mills were used; Wiley mill (WM) and disc mill (DM). Ground OPMF from each milling process was examined for its particle size distribution and aspect ratio by sieve and microscopic analyses, respectively. Results showed that DM-OPMF had smaller diameter fibre with uniform particle size compared to the WM-OPMF. Surface morphology study by SEM showed that DM-OPMF had rougher surface compared to WM-OPMF. Furthermore, it was found that PP/DM-OPMF biocomposite had higher tensile strength compared to PP/WM-OPMF, with almost two-fold. Thus, it is suggested that small diameter and uniform size fibre may improve stress transfer and surface contact between the fibre and polymer matrix and cause well dispersion of filler throughout the polymer resulted in better tensile strength of PP/DM-OPMF Compared to PP/WM-OPMF biocomposite. Overall, it can be concluded that disc milling could serve as a simple and effective grinding method for improving the tensile properties of biocomposite.
Banana pulp (BP) noodles prepared by partial substitution of wheat flour with green Cavendish banana pulp flour were assessed pH, color, tensile strength and elasticity, and in-vitro hydrolysis index (HI) and estimated glycemic index (GI). BP noodles had lower L* (darker) and b* values (less yellow) but higher tensile strength and elasticity modulus than control noodles. Following an in-vitro starch hydrolysis studies, it was found that GI of BP noodles was lower than control noodles. Partial substitution of green banana pulp into noodles may be useful for controlling starch hydrolysis of yellow noodles.
The addition of ribose to minced chicken or minced pork followed by heating at 95oC yielded minced
meat with different pH, colour (CIE L*, b*) and absorbance values that can be used as indicators for species differentiation. The higher intensity of the Maillard reaction parameters in minced chicken was due to the higher protein and lysine contents, and the presence of more water-soluble proteins within the minced chicken during heating. Cluster analysis using Maillard reaction parameters showed that the two types of minced meat could be classified into two different groups. A confidence interval (95% confidence) analysis revealed that the absorbance, CIE L* values, and CIE b* values could be used as indicators for differentiation between the two types of minced meat, as the intervals between these Maillard reaction parameters for the two minced meats were far apart.
Introduction: Second generation functionalized nanocrystal is the advancement of nanocrystal technology with great potential to accommodate BCS (Biopharmaceutical Classification System) class II drugs to meet their formulation and drug delivery challenges. Gliclazide is a BCS class II drug used in the treatment of type 2 diabetes, shows poor water solubility and low rate of dissolution, leads to poor and variable oral bioavailability. The second generation poly(D,L-lactide-co-glycolide) (PLGA) Hydroxypropyl methylcellulose (HPMC) based functionalized nanocrystals of gliclazide were prepared by a combination method of emulsion diffusion-high pressure homogenization-solvent evaporation. Methods: Gliclazide second generation nanocrystals were fabricated with taguchi orthogonal experimental design in combination of step up and top down nanoformulation strategies using drug-polymer (PLGA) ratio at 1:0.5, 1:0.75, 1:1 with HPMC(0.5, 0.75, 1% w/v) as stabilizer. The formulated gliclazide PLGA-HPMC nanocrystals were investigated on particle size, polydispersity index, zeta potential, solubility study, drug entrapment efficiency, in vitro drug release, and surface morphology and compatibility studies. The gliclazide PLGA nanocrystals formulation was prepared with Drug : PLGA at 1: 1 ratio with concentrations 0.75% w/v HPMC at 5 homogenization cycles with 1000bar produce optimized gliclazide nanocrystals. Results: The optimized MSGNC8 formulation
showed particle size of 239.9 nm, entrapment efficiency 98.62%, and drug release of 43.75%, 82.12% and 98.08% at 3hrs, 24hrs, and 48hrs compared to pure gliclazide % drug release of 28.73%, 67.51% and 78.41% at 3hrs, 24hrs, 48hrs respectively. The solubility study of optimized formulation shows eight folds increased in saturation solubility compared to pure drug. Scanning electron microscopy (SEM) analysis of the gliclazide nanocrystals revealed that
gliclazide retained its crystal morphology in polymeric nanocrystals. Further, fourier-transform infrared spectroscopy (FTIR) and differential scanning calorimetry (DSC) studies on gliclazide PLGA-HPMC nanocrystals emphasize drug and excipient compatibility in development of gliclazide nanocrystals. Conclusion: The potential outcomes of research findings emphasize that the developed gliclazide second-generation nanocrystals, which resulted in increase in drug solubility and rate of dissolution with delayed modified release, can be explored in delivery of gliclazide for type 2 diabetes management.
Orally disintegrating tablets are a solid dosage form that will disintegrate rapidly within 3 minutes upon contact with saliva. Fillers or diluents are excipients that are used to make up the volume of orally disintegrating tablets, and some might act as a disintegrant or binder that will affect the physical properties of orally disintegrating tablets. The objective of this study was to formulate and evaluate physical properties of orally disintegrating tablets containing Annona muricata leaves extract by a freeze-drying method using different fillers at different concentrations. In this study, fifteen formulations of orally disintegrating tablets were prepared by a freeze-drying method with different fillers such as starch, lactose, microcrystalline cellulose, StarLac, and CombiLac at 5%, 10%, and 15%. The orally disintegrating tablets were evaluated for hardness, thickness, weight variation, friability, and disintegration time test. The optimum formulation was chosen and incorporated with Annona muricata leaves extract. The results obtained in this work indicated that Formulation 3, with 15% starch, was the most optimum formulation due to the shortest disintegration time (21.08 seconds ± 4.24 seconds), and all the physical tests were within the acceptable range. The orally disintegrating tablets containing Annona muricata leaves extract possessed antioxidant activity and stable at least for 3 months under 60°C and 75% relative humidity.
Oral drug delivery has been recognized as the most desirable drug administration method among other drug delivery routes due to its ease of administration, long shelf life, and low cost. Orally disintegrating tablets disintegrate within seconds in the mouth without the need of water for swallowing. This unique feature of orally disintegrating tablets is favorable to special populations such as geriatric and pediatric patients. Formulation optimization is significant to obtain the optimal combination of tablet constituents, as the tablet composition is influential on dosage-form characteristics. The objective of this study was to investigate the effect of different types of fillers and percentage on the physical properties of orally disintegrating tablets by using amlodipine as the model drug. Blank orally disintegrating tablets containing different fillers, namely, Sorbolac 400, Granulac 200, and CombiLac with different percentages, were prepared using the wet granulation method and were evaluated based on weight variation, hardness, thickness, friability, and disintegration time. Formulation 5 that consists of 25% Granulac 200 showed the optimal result among all formulations with the fastest disintegration time (96.17 s Å} 18.40) and sufficient tablet hardness (4.59 kg Å} 0.70). Hence, formulation 5 was selected as the optimal formulation and incorporated with amlodipine. From this study, it can be concluded that excipients have an essential role in determining the physical properties of orally disintegrating tablets.
Conventional alginate pellets underwent rapid drug dissolution and failed to exert colon targeting unless subjected to complex coating. This study designed coatless delayed-release oral colon-specific alginate pellets for ulcerative colitis treatment. Alginate pellets, formulated with water-insoluble ethylcellulose and various calcium salts, were prepared using solvent-free melt pelletization technique which prevented reaction between processing materials during agglomeration and allowed reaction to initiate only in dissolution. Combination of acid-soluble calcium carbonate and highly water-soluble calcium acetate did not impart colon-specific characteristics to pellets due to pore formation in fragmented matrices. Combination of moderately water-soluble calcium phosphate and calcium acetate delayed drug release due to rapid alginate crosslinking by soluble calcium from acetate salt followed by sustaining alginate crosslinking by calcium phosphate. The use of 1:3 ethylcellulose-to-alginate enhanced the sustained drug release attribute. The ethylcellulose was able to maintain the pellet integrity without calcium acetate. Using hydrophobic prednisolone as therapeutic, hydrophilic alginate pellets formulated with hydrophobic ethylcellulose and moderately polar calcium phosphate exhibited colon-specific in vitro drug release and in vivo anti-inflammatory action. Coatless oral colon-specific alginate pellets can be designed through optimal formulation with melt pelletization as the processing technology.
The predilection of a bi-layered tablet to fail in the interface region after its initial formation in the compaction process reduces its practicality as a choice for controlled release solid drug delivery system. Hence, a fundamental appreciation of the governing mechanism that causes the weakening of the interfacial bonds within the bi-layered tablet is crucial in order to improve the overall bi-layered tablet mechanical integrity. This work has shown that the occurrence of the elastic relaxation in the interface region during the ejection stage of the compaction process decreases with the increase in the bi-layered tablet interface strength. This is believed to be due to the increase in the plastic bonding in the interface region. The tablet diametrical elastic relaxation affects the tablet height elastic relaxation, where the impediment of the tablet height expansion is observed when the interface region experiences a diametrical expansion.
Pelletized dosage forms can be prepared by different methods which, in general, are time consuming and labor intensive. The current study was carried out to investigate the feasibility of preparing the spherical pellets of omeprazole by sieving-spheronization. An optimized formulation was also prepared by extrusion-spheronization process to compare the physical parameters between these two methods. The omeprazole pellets were consisted of microcrystalline cellulose, polyvinylpyrrolidone K 30, sodium lauryl sulphate and polyethylene glycol 6000. The omeprazole delay release system was developed by coating the prepared pellets with aqueous dispersion of Kollicoat 30 DP. The moisture content, spheronization speed and residence time found to influence the final properties of omeprazole pellets prepared by extrusion-spheronization and sieving-spheronization. The Mann-Whitney test revealed that both methods produced closely similar characteristics of the pellets in terms of, friability (p=0.553), flowability (p=0.677), hardness (p=0.103) and density (bulk, p=0.514, tapped, p=0.149) except particle size distribution (p=0.004). The percent drug release from the coated formulation prepared by sieving-spheronization and extrusion spheronization was observed to be 84.12 ± 1.10% and 82.67 ± 0.96%, respectively. Dissolution profiles of both formulations were similar as indicated by values of f1 and f2, 1.52 and 89.38, respectively. The coated formulation prepared by sieving-spheronization and commercial reference product, Zimore ® also showed similar dissolution profiles (f1=1.22, f2=91.52). The pellets could be prepared using sieving-spheronization. The process is simple, easy, less time- and labor-consuming and economical as compared to extrusion-spheronization process.
A search for narrow resonances in proton-proton collisions at sqrt[s]=13 TeV is presented. The invariant mass distribution of the two leading jets is measured with the CMS detector using a data set corresponding to an integrated luminosity of 2.4 fb^{-1}. The highest observed dijet mass is 6.1 TeV. The distribution is smooth and no evidence for resonant particles is observed. Upper limits at 95% confidence level are set on the production cross section for narrow resonances with masses above 1.5 TeV. When interpreted in the context of specific models, the limits exclude string resonances with masses below 7.0 TeV, scalar diquarks below 6.0 TeV, axigluons and colorons below 5.1 TeV, excited quarks below 5.0 TeV, color-octet scalars below 3.1 TeV, and W^{'} bosons below 2.6 TeV. These results significantly extend previously published limits.
This study aimed to assess the robustness of using a spray drying approach and formulation design in producing inhalable phage powders. Two types of Pseudomonas phages, PEV2 (Podovirus) and PEV40 (Myovirus) in two formulations containing different amounts of trehalose (70% and 60%) and leucine (30% and 40%) were studied. Most of the surface of the produced powders was found to be covered in crystalline leucine. The powders were stored at 4 °C and 20 °C under vacuum. The phage stability and in vitro aerosol performance of the phage powders were examined on the day of production and after 1, 3 and 12 months of storage. A minor titer loss during production was observed for both phages (0.2-0.8 log10 pfu/ml). The storage stability of the produced phage powders was found to be phage and formulation dependent. No further reduction in titer occurred for PEV2 powders stored at 4 °C across the study. The formulation containing 30% leucine maintained the viability of PEV2 at 20 °C, while the formulation containing 40% leucine gradually lost titer over time with a storage reduction of ∼0.9 log10 pfu/ml measured after 12 months. In comparison, the PEV40 phage powders generally had a ∼ 0.5 log10 pfu/ml loss upon storage regardless of temperature. When aerosolized, the total in vitro lung doses of PEV2 were of the order of 107 pfu, except the formulation containing 40% leucine stored at 20 °C which had a lower lung dose. The PEV40 powders also had lung doses of 106-107 pfu. The results demonstrate that spray dried Myoviridae and Podoviridae phage in a simple formulation of leucine and trehalose can be successfully stored for one year at 4 °C and 20 °C with vacuum packaging.
A study was done on the feasibility of inulin, a fructooligosaccharides with the health benefits of prebiotic, as partial sugar replacer in “kaya” by investigating the effects of different substitution levels (0%; control, 10%, 30% and 50%) on the sensory properties. The samples were investigated by 10 descriptive panelists for colour, sweetness, smoothness, firmness, adhesiveness and spreadability attributes before further evaluated by 100 consumers for acceptance levels. Consistent with the descriptive panel, the evaluation by the consumers showed formulated samples at 10% and 30% were comparable to the commercial “kaya” being no significant difference (p>0.05) found in acceptability scores. 50% substitution received lower acceptability scores and was significantly different (p