Recently, various solid wastes from industry such as glass waste, fly ash, sewage sludge and slag have been recycled into various value-added products such as ceramic tile. The conventional solutions of dumping the wastes in landfills or incineration, including in Malaysia are getting obsolete as the annual huge amount of the solid wastes would boost-up disposal cost and may cause permanent damage to the flora and fauna. This recent waste recycling approach is much better and greener as it can resolve problems associated with over-limit storage of industrial wastes and reduce exploration of natural resources for ceramic tile to continuously sustain the nature. Therefore, in this project, an attempt was made to recycle electric arc furnace (EAF) slag waste, obtained from Malaysia's steel making industry, into ceramic tile via conventional powder compaction method. The research work was divided into two stages. The first stage was to evaluate the suitability of EAF slag in ceramic tile by varying weight percentage of EAF slag (40 wt.%, 50 wt.% and 60 wt.%) and ball clay (40 wt.%, 50 wt.% and 60 wt.%), with no addition of silica and potash feldspar. In the second stage, the weight percentage of EAF slag was fixed at 40 wt.% and the percentage of ball clay (30 wt.% and 40 wt.%), feldspar (10 wt.% and 20 wt.%) and silica (10 wt.% and 20 wt.%) added was varied accordingly. Results obtained show that as weight percentage of EAF slag increased up to 60 wt.%, the percentage of apparent porosity and water absorption also rose, with a reduction in tile flexural strength and increased porosity. On the other hand, limiting the weight percentage of EAF slag to 40 wt.% while increasing the weight percentage of ball clay led to a higher total percentage of anorthite and wollastonite minerals, resulting in higher flexural strength. It was found that introduction of silica and feldspar further improved the flexural strength due to optimization of densification process. The highest flexural strength, lowest apparent porosity and water absorption of EAF slag based tile was attained at the composition of 40 wt.% EAF slag--30 wt.% ball clay--10 wt.% feldspar--20 wt.% silica. The properties of ceramic tile made with EAF slag waste (up to 40 wt.%), especially flexural strength are comparable to those of commercial ceramic tile and are, therefore, suitable as high flexural strength and heavy-duty green ceramic floor tile. Continuous development is currently underway to improve the properties of tile so that this recycling approach could be one of the potential effective, efficient and sustainable solutions in sustaining our nature.
Power generation from biomass is an attractive technology that utilizes agricultural residual waste. In order to explain the behavior of biomass-fired fluidized bed incinerator, biomass sources from agricultural residues (rice husk and palm kernel) were co-fired with coal in a 0.15m diameter and 2.3m high fluidized bed combustor. The combustion efficiency and carbon monoxide emissions were studied and compared with those for pure coal combustion. Co-combustion of a mixture of biomass with coal in a fluidized bed combustor designed for coal combustion increased combustion efficiency up to 20% depending upon excess air levels. Observed carbon monoxide levels fluctuated between 200 and 900 ppm with the addition of coal. It is evident from this research that efficient co-firing of biomass with coal can be achieved with minimal modifications to existing coal-fired boilers.
In order to address slagging, fouling and high-temperature corrosion problems caused by alkali metals in Municipal Solid Waste (MSW), in-situ measurement of alkali metal in MSW incinerators is needed. The paper presents experimental measurements of temperatures and alkali metal concentrations in two MSW incinerators based on Flame Emission Spectroscopy (FES). Through the analysis of spontaneous emission spectra and a calibration procedure, the concentration of gas phase sodium (Na) and potassium (K), temperature and thermal radiation in the incinerator were in-situ measured by a portable spectral system simultaneously. Experimental results showed MSW composition has significant effect on the measured gaseous Na and K. Higher volatile content in MSW may enhance the alkali metal emission. Besides that, the released gaseous Na and K in the two incinerators are correlated with temperature in incinerators. The study provided a low cost and effective solution for in-situ measurement of temperature and alkali metal concentration in MSW incinerators.
Malaysian authorities has planned to minimize and stop when applicable unsanitary dumping of waste as it puts human health and the environment at elevated risk. Cost, energy and revenue are mostly adopted to draw the blueprint of upgrading municipal solid waste management system, while the carbon footprint emissions criterion rarely acts asa crucial factor. This study aims to alert Malaysian stakeholders on the uneven danger of carbon footprint emissions of waste technologies. Hence, three scenarios have been proposed and assessed mainly on the carbon footprint emissions using the 2006 IPCC methodology. The first scenario is waste dumping in sanitary landfills equipped with gas recovery system, while the second scenario includes anaerobic digestion of organics and recycling of recyclable wastes such as plastic, glass and textile wastes. The third scenario is waste incineration. Besides the carbon footprint emissions criterion, other environmental concerns were also examined. The results showed that the second scenario recorded the lowest carbon footprint emissions of 0.251t CO2 eq./t MSW while the third scenario had the highest emissions of 0.646t CO2 eq./t MSW. Additionally, the integration between anaerobic digestion and recycling techniques caused the highest avoided CO2 eq. emissions of 0.74t CO2 eq./t MSW. The net CO2 eq. emissions of the second scenario equaled -0.489t CO2 eq./t MSW due to energy recovery from the biogas and because of recycled plastic, glass and textile wastes that could replace usage of raw material. The outcomes also showed that the first scenario generates huge amount of leachate and hazardous air constituents. The study estimated that a ton of dumped waste inside the landfills generates approximately 0.88m3 of trace risky compounds and 0.188m3 of leachate. As for energy production, the results showed that the third scenario is capable of generating 639kWh/t MSW followed by the second scenario with 387.59kWh/t MSW. The first scenario produced 296.79kWh/t MSW. In conclusion, the outcomes of this study recommend an integrated scenario of anaerobic digestion and recycling techniques to be employed in Malaysia.
The integration of hydrogen in the primary energy mix requires a major technological shift in virtually every energy-related application. This study has attempted to investigate the techno-economic solar photovoltaic (PV) integrated water electrolysis and waste incineration system. Three different strategies, i.e., (i) PV + Battery(Hybrid mode with required batteries); (ii) auto-ignition (Direct coupling); and (iii) PV + Secondary-Electrolyzer(Direct coupling assisted with secondary electrolyzer), have been envisioned. The 'PV + Battery' consume 42.42 % and 15.07 % less energy than the auto-ignition and 'PV + Secondary-Electrolyzer' methods. However, the capital cost of 'PV + Battery' has been calculated to be 15.4 % and 11.8 % more than auto-ignition and 'PV + Secondary-Electrolyzer, respectively.The energy consumption relative to waste input, the 'PV + Battery' method used 80 % less energy, while auto-ignition and 'PV + Secondary-Electrolyzer' showed 70.5 % and 77.5 % less energy, respectively. Furthermore, these approaches showed a vast difference in cost-benefit for the longer run. 'PV + Battery' was forecasted to be 73.3 % and 23.3 % more expensive than auto-ignition and 'PV + Secondary-Electrolyzer' methods, respectively, for 30 years. Overall, this study can benefit from using either of these methods depending on the application, usage scale, and climatic conditions.
Industrial plastic waste is growing globally at an alarming rate and environmental pollution from traditional landfill disposal and incineration treatments are of great concern. As a strategy to reduce plastic pollution, value-added composite materials from industrial plastic wastes reinforced with recycled nylon fibers for use in floor paving tile applications were developed. This is to address the disadvantages of existing ceramic tiles which are relatively heavy, brittle, and expensive. The plastic waste composite structures were produced via compression molding technique at an optimized randomly oriented constant fiber volume fraction of 50 wt% after the initial sorting, cleaning, drying, pulverizing, and melt-mixing. The molding temperature, pressure, and time for the composite's structures were 220 ℃, 65 kg.cm-3, and 5 min respectively. The composites' thermal, mechanical, and microstructural properties were characterized in accordance with appropriate ASTM standards. From the results obtained, the differential scanning calorimetry (DSC) of mixed plastic wastes and nylon fiber wastes showed a processing temperature range of 130-180 ℃, and 250 ℃ respectively. Thermal degradation temperature (TGA) of the plastic and nylon fiber waste composites were stable above 400 ℃ with maximum bending strength, however, the reinforced plastic waste sandwiched composite structures had outstanding mechanical properties indicating unique characteristics suitable for floor paving tiles. Hence, the current research has developed tough and lightweight tiles composites that are economically viable, and their application will contribute to the development of the building and construction sectors thereby reducing about 10-15% of annual plastic waste generation and a sustainable environment.
Most households and healthcare facilities usually dispose of contaminated, unused, or expired (CUE) medicines with municipal wastes, the disposal of which usually amounts to $790/ton in the USA and £450/ton in the UK. Solid (e.g., tablets, capsules, powders) and semi-solid (e.g., ointment, creams) pharmaceuticals are managed with incineration/pyrolysis, encapsulation, and engineered landfills, whereas wastewater treatment plants (WWTPs) are recommended for liquid pharmaceutical wastes (PWs). However, to date, the sustainability and eco-friendliness profile of these techniques are only subjectively ensured, leading to controversial viewpoints in many guidelines. Each technique has relative strengths and weaknesses, and their comparative weighting to maximize these profiles is sought after. The present comprehensive review aims to fulfil knowledge gaps in this regard. Four electronic databases (e.g., PubMed/MEDLINE, Scopus, and ScienceDirect) were searched for PW management (PWM)-related qualitative and quantitative articles published till December 31, 2022. Articles without details of waste disposal techniques and their health and environmental impacts were excluded. Based on the literature review, we determine that incineration can be considered a sustainable option for solid and semi-solid PWs, and WWTPs can be eco-friendly for liquid PWs, whereas encapsulation and landfilling are less sustainable. It is high time that objectively proven sustainable and eco-friendly techniques be implemented for PWM based on their dosage forms or nature of hazards. Medicine take-back, eco-pharmacovigilance, extended producer responsibility, co-payment, and life cycle analysis of pharmaceuticals focusing on reduction, reuse/re-dispensing can be integrated to make existing models sustainable, circular, and eco-friendly.
An appropriate technology for waste utilisation, especially for a large amount of abundant pressed-shredded oil palm empty fruit bunch (OFEFB), is important for the oil palm industry. Self-sustained pyrolysis, whereby oil palm biomass was combusted by itself to provide the heat for pyrolysis without an electrical heater, is more preferable owing to its simplicity, ease of operation and low energy requirement. In this study, biochar production under self-sustained pyrolysis of oil palm biomass in the form of oil palm empty fruit bunch was tested in a 3-t large-scale pool-type reactor. During the pyrolysis process, the biomass was loaded layer by layer when the smoke appeared on the top, to minimise the entrance of oxygen. This method had significantly increased the yield of biochar. In our previous report, we have tested on a 30-kg pilot-scale capacity under self-sustained pyrolysis and found that the higher heating value (HHV) obtained was 22.6-24.7 MJ kg(-1) with a 23.5%-25.0% yield. In this scaled-up study, a 3-t large-scale procedure produced HHV of 22.0-24.3 MJ kg(-1) with a 30%-34% yield based on a wet-weight basis. The maximum self-sustained pyrolysis temperature for the large-scale procedure can reach between 600 °C and 700 °C. We concluded that large-scale biochar production under self-sustained pyrolysis was successfully conducted owing to the comparable biochar produced, compared with medium-scale and other studies with an electrical heating element, making it an appropriate technology for waste utilisation, particularly for the oil palm industry.
A choice experiment analysis was conducted to estimate the preference for specific waste disposal technologies in Malaysia. The study found that there were no significant differences between the choice of a sanitary landfill or an incinerator. What matters is whether any disposal technology would lead to obvious social benefits. A waste disposal plan which is well linked or integrated with the community will ensure its acceptance. Local authorities will be challenged to identify solid waste disposal sites that are technically appropriate and also socially desirable.
Incineration of industrial waste produces large quantities of bottom ash which are normally sent to secured landfill, but is not a sustainable solution. Use of bottom ash in engineering applications will contribute to sustainability and generate revenue. One way of using the industrial waste incineration bottom ash is in controlled low-strength material (CLSM). Use of bottom ash in CLSM has problems related to bleeding and excessive strength development and so an additive has to be used to control bleeding and strength development. The main objective of this research is to study the effect of kaolin addition on the performance of CLSM made using industrial waste incineration bottom ash. CLSM mixes were made with bottom ash, cement, and refined kaolin. Various tests were performed on the CLSM in fresh and hardened states including compressive strength, water absorption, California bearing ratio (CBR) and the tests for concentration of leachable substances on the bleed and leachate. The compressive strength of CLSM tested ranged from 0.11 to 9.86 MPa. CBR values ranged from 6 to 46, and water absorption values from 12 to 36%. It was shown that the addition of kaolin delayed the initial setting time of CLSM mixtures, reduced bleeding, lowered the compressive strength, and increased the values of water absorption, sorption, and initial surface absorption. The CLSM tested did not have corrosivity. It was shown that the hardened CLSM was non hazardous, and the addition of kaolin increased the concentration of heavy metals and salts in the bleed and leachate.
Chlorine radical plays an important role in the formation of ozone and secondary aerosols in the troposphere. It is hence important to develop comprehensive emissions inventory of chlorine precursors in order to enhance our understanding of the role of chlorine chemistry in ozone and secondary pollution issues. Based on a bottom-up methodology, this study presents a comprehensive emission inventory for major atomic chlorine precursors in the Yangtze River Delta (YRD) region of China for the year 2017. Four primary chlorine precursors are considered in this study: hydrogen chloride (HCl), fine particulate chloride (Cl-) (Cl- in PM2.5), chlorine gas (Cl2), and hypochlorous acid (HClO) with emissions estimated for twelve source categories. The total emissions of these four species in the YRD region are estimated to be 20,424 t, 15,719 t, 1556 and 9331 t, respectively. The emissions of HCl are substantial, with major emissions from biomass burning and coal combustion, together accounting for 68% of the total HCl emissions. Fine particulate Cl- is mainly emitted from industrial processing, biomass burning and waste incineration. The emissions of Cl2 and HClO are mainly associated with usage of chlorine-containing disinfectants, for example, water treatment, wastewater treatment, and swimming pools. Emissions of each chlorine precursor are spatially allocated based on the characteristics of individual source category. This study provides important basic dataset for further studies with respect to the effects of chlorine chemistry on the formation of air pollution complex in the YRD region.
Polychlorinated dibenzo-p-dioxins (PCDDs) and polychlorinated dibenzofurans (PCDFs) are toxic compounds derived from anthropogenic sources that stay in the environment for long periods. Ambient air has become the most important pathway for the transfer of PCDDs/PCDFs from emission sources to the environment. This review intends to summarise the information available on atmospheric PCDDs/PCDFs in the countries of Southeast Asia to provide a detailed description of the trends in PCDDs/PCDFs emissions, key sources, and levels in urban, rural, and industrial air as reported in peer-reviewed literature since 2000 and by the United Nations Environment Programme. As the largest country in Southeast Asia, Indonesia is the major PCDDs/PCDFs emitter, accounting for 72.81% of the total release of PCDDs/PCDFs in the air from all available inventories in this region, while Brunei Darussalam is the lowest emitter, contributing to less than 0.02%. Open burning processes have become the largest source of ambient PCDDs/PCDFs in the region (69.62%), followed by waste incineration (10.69%), and ferrous and non-ferrous metal production (8.78%). PCDDs/PCDFs levels in rural areas ranged between 10 and 38 fg TEQ m-3; however, where open burning waste has occurred, the levels rose to 12-29 times higher. In urban areas, ambient levels were 15 times greater than in rural areas, varying from 23 to 565 fg TEQ m-3. Atmospheric concentrations near industrial palm oil and waste incinerator sites were between 64 and 1530 fg TEQ m-3. The non-cancer risk of ambient exposure to PCDDs/PCDFs through inhalation is low among populations near facilities emitting PCDDs/PCDFs. The lack of local technical capacity, the high economic costs, and the lack of established human resource capacities have been the major challenges in conducting ambient PCDDs/PCDFs studies in most countries in the region.
An incredible amount of joss fly ash is produced from the burning of Chinese holy joss paper; thus, an excellent method of recycling joss fly ash waste to extract aluminosilicate nanocomposites is explored. The present research aims to introduce a novel method to recycle joss fly ash through a simple and straightforward experimental procedure involving acidic and alkaline treatments. The synthesized aluminosilicate nanocomposite was characterized to justify its structural and physiochemical characteristics. A morphological analysis was performed with field-emission transmission electron microscopy, and scanning electron microscopy revealed the size of the aluminosilicate nanocomposite to be ~25 nm, while also confirming a uniformly spherical-shaped nanostructure. The elemental composition was measured by energy dispersive spectroscopy and revealed the Si to Al ratio to be 13.24 to 7.96, showing the high purity of the extracted nanocomposite. The roughness and particle distribution were analyzed using atomic force microscopy and a zeta analysis. X-ray diffraction patterns showed a synthesis of faceted and cubic aluminosilicate crystals in the nanocomposites. The presence of silica and aluminum was further proven by X-ray photoelectron spectroscopy, and the functional groups were recognized through Fourier transform infrared spectroscopy. The thermal capacity of the nanocomposite was examined by a thermogravimetric analysis. In addition, the research suggested the promising application of aluminosilicate nanocomposites as drug carriers. The above was justified by an enzyme-linked apta-sorbent assay, which claimed that the limit of the aptasensing aluminosilicate-conjugated ampicillin was two-fold higher than that in the absence of the nanocomposite. The drug delivery property was further justified through an antibacterial analysis against Escherichia coli (gram-negative) and Bacillus subtilis (gram-positive).
Mercury emission into the atmosphere is a global concern due to its detrimental effects on human health in general. The two main sources of mercury emission are natural sources and anthropogenic sources. Mercury emission from natural sources include volcanic activity, weathering of rocks, water movement and biological processes which are obviously inevitable. The anthropogenic sources of mercury emission are from coal combustion, cement production and waste incineration. Thus, in order to reduce mercury emission it is appropriate to investigate how mercury is released from the anthropogenic sources and consequently the mercury removal technology that can be implemented in order to reduce mercury emission into the atmosphere. Many alternatives have been developed to reduce mercury emission and the recent application of activated carbon showed high potential in the adsorption of elemental mercury. This paper discusses the ability of activated carbon and variable parameters that influence mercury removal efficiency in flue gas.
A chemical method to synthesize amorphous silica nanoparticles from the incinerated paddy straw has been introduced. The synthesis was conducted through the hydrolysis by alkaline-acidic treatments. As a result, silica particles produced with the sizes were ranging at 60-90 nm, determined by high-resolution microscopy. The crystallinity was confirmed by surface area electron diffraction. Apart from that, chemical and diffraction analyses for both rice straw ash and synthesized silica nanoparticles were conducted by X-ray diffraction and Fourier-transform infrared spectroscopy. The percentage of silica from the incinerated straw was calculated to be 28.3. The prominent surface chemical bonding on the generated silica nanoparticles was with Si-O-Si, stretch of Si-O and symmetric Si-O bonds at peaks of 1090, 471, and 780 cm-1, respectively. To confirm the impurities of the elements in the produced silica, were analyzed using X-ray photoelectron spectroscopy and energy dispersive X-ray spectroscopy. The stability of silica nanoparticles was investigated using thermogravimetric analysis and zeta potential. The measured size from zeta potential analysis was 411.3-493 nm and the stability of mass reduction was located at 200 °C with final amount of mass reduced ∼88% and an average polydispersity Index was 0.195-0.224.
The presence of heavy metals in aquatic systems has become a serious problem. Heavy metals can haveadverse effects on the environment as well as on human health. As a result, much attention has beengiven to new technologies for removal of heavy metal ions from contaminated waters. In this study,Microwave Incinerated Rice Husk Ash (MIRHA), a locally available agricultural waste, was used for theremoval of Cd (as a representative heavy metal) from synthetic wastewater by batch adsorption process.The effects of pH, initial metal concentration, and contact time on Cd removal efficiency were studied.pH 4 was found to be the optimum. The removal efficiency was found to be correlated with the initialmetal concentration and contact time between adsorbent and adsorbate. Cd adsorption kinetics followedthe pseudo-second-order model and implied chemisorption. The adsorption equilibrium of Cd can bewell described by the Freundlich isotherm model.
Sludge is an unavoidable product of wastewater treatment that creates problems of disposal. Increasingly, strict environmental control regulations have resulted in limitations on sludge disposal options.Disposal by incineration has been found to be a good option. In this research, application of domestic waste sludge powder (DWSP) was used as cement replacement in concrete mix. This study utilised replacement of 3 %, 5 %, 7 %, 10 % and 15 % by weight of OPC with water binder (w/b) ratio of 0.60, 0.55 and 0.40 for Grade 30, Grade 40 and Grade 50 respectively. The performance of DWSP concrete in terms of its compressive strength, water absorption, water permeability and Rapid Chloride Ion penetration were investigated. All values of compressive strength for DWSP concrete were lower compared to the OPC control, and the strength decreased as the percentage of replacement with DWSP increased for Grade 30 and Grade 50, except for Grade 40 at replacement of 7 %. Meanwhile, water absorption and water permeability for the DWSP concrete increased as the replacement increased. Overall, with further research in producing quality DWSP, the potential of using this waste as a cement replacement material is very promising.
Fibres have been used in construction materials for a very long time. Through previous research and investigations, the use of natural and synthetic fibres have shown promising results, as their presence has demonstrated significant benefits in terms of the overall physical and mechanical properties of the composite material. When comparing fibre reinforcement to traditional reinforcement, the ratio of fibre required is significantly less, making fibre reinforcement both energy and economically efficient. More recently, waste fibres have been studied for their potential as reinforcement in construction materials. The build-up of waste materials all around the world is a known issue, as landfill space is limited, and the incineration process requires considerable energy and produces unwanted emissions. The utilisation of waste fibres in construction materials can alleviate these issues and promote environmentally friendly and sustainable solutions that work in the industry. This study reviews the types, properties, and applications of different fibres used in a wide range of materials in the construction industry, including concrete, asphalt concrete, soil, earth materials, blocks and bricks, composites, and other applications.
Thermal performance, combustibility, and fire propagation of fly ash-metakaolin (FA-MK) blended geopolymer with the addition of aluminum triphosphate, ATP (Al(H2PO4)3), and monoaluminium phosphate, MAP (AlPO4) were evaluated in this paper. To prepare the geopolymer mix, fly ash and metakaolin with a ratio of 1:1 were added with ATP and MAP in a range of 0-3% by weight. The fire/heat resistance was evaluated by comparing the residual compressive strengths after the elevated temperature exposure. Besides, combustibility and fire propagation tests were conducted to examine the thermal performance and the applicability of the geopolymers as passive fire protection. Experimental results revealed that the blended geopolymers with 1 wt.% of ATP and MAP exhibited higher compressive strength and denser geopolymer matrix than control geopolymers. The effect of ATP and MAP addition was more obvious in unheated geopolymer and little improvement was observed for geopolymer subjected to elevated temperature. ATP and MAP at 3 wt.% did not help in enhancing the elevated-temperature performance of blended geopolymers. Even so, all blended geopolymers, regardless of the addition of ATP and MAP, were regarded as the noncombustible materials with negligible (0-0.1) fire propagation index.
Incineration and disposal of carbon fiber waste from the aircraft industry lead to serious energy consumption and environmental pollution. The use of this waste as reinforcement is a wise approach to appreciate the high performance of the carbon fiber. This study is part of our effort to develop new green rubber foam from recycled carbon fiber prepreg (rCFP) reinforced natural rubber via internal mixer. It is focusing on the effect of different rCFP loading at 1, 3, 5, and 7 parts per hundred rubbers (phr) as reinforcement. The samples were prepared by melt compounding using an internal mixer and expanded via two step heat transfer foaming process. The physical properties of the green rubber foam were characterized and the results were observed to systematically correlate with the impact properties of the foam. The absorbed energy of the foam increases up to 0.3 joules with increasing relative foam density of 0.81 which is associated with the formation of smaller foam cells ~0.68mm and more spherical shape pores.