The development of wearable artificial kidney demands an efficient dialysate recovery, which relies upon the adsorption process. This study proposes a solution to solve the problem of competitive adsorption between the uremic toxins by employing two adsorptive components in a membrane separation process. Dual-layer hollow fiber (DLHF) membranes, which are composed of a polysulfone (PSf)/activated carbon (AC) inner layer and a PSf/poly(methyl methacrylate) (PMMA) outer layer, were prepared for co-adsorptive removal of creatinine and urea from aqueous solution. The DLHF membranes were characterized in terms of morphological, physicochemical, water transport, and creatinine adsorption properties. The membrane was then subjected to an ultrafiltration adsorption study for performance evaluation. The incorporation of AC in membrane, as confirmed by microscopic and surface analyses, has improved the pure water flux up to 25.2 L/(m2 h). A membrane with optimum AC loading (9 wt %) demonstrated the highest maximum creatinine adsorption capacity (86.2 mg/g) based on the Langmuir adsorption isotherm model. In the ultrafiltration adsorption experiment, the membrane removed creatinine and urea with a combined average percent removal of 29.3%. Moreover, the membrane exhibited creatinine and urea uptake recoveries of 98.8 and 81.2%, respectively. The combined action of PMMA and AC in the PSf DLHF membrane has made the adsorption of multiple uremic toxins possible during dialysate recovery.
Bacillus licheniformis α-amylase (BLA) was chemically modified using 100-fold molar excess of succinic anhydride over protein or 0.66 M potassium cyanate to obtain 42 % succinylated and 81 % carbamylated BLAs. Size and charge homogeneity of modified preparations was established by Sephacryl S-200 HR gel chromatography and polyacrylamide gel electrophoresis. Conformational alteration in these preparations was evident by the larger Stokes radii (3.40 nm for carbamylated and 3.34 nm for succinylated BLAs) compared to 2.43 nm obtained for native BLA. Urea denaturation results using mean residue ellipticity (MRE) as a probe also showed conformational destabilization based on the early start of transition as well as ΔG(D)(H(2)O) values obtained for both modified derivatives and Ca-depleted BLA. Decrease in ΔG(D)(H(2)O) value from 5,930 cal/mol (for native BLA) to 3,957 cal/mol (for succinylated BLA), 3,336 cal/mol (for carbamylated BLA) and 3,430 cal/mol for Ca-depleted BLA suggested reduced conformational stability upon modification of amino groups of BLA or depletion of calcium. Since both succinylation and carbamylation reactions abolish the positive charge on amino groups (both α- and ε- amino), the decrease in conformational stability can be ascribed to the disruption of salt bridges present in the protein which might have released the intrinsic calcium from its binding site.
In the current study, a phase inversion scheme was employed to fabricate hydroxyapatite (HA)/polysulfone (PSF)-based asymmetric membranes using a film applicator with water as a solvent and nonsolvent exchanging medium. Fourier Transform Infrared (FTIR) and X-ray diffraction (XRD) spectroscopic studies were conducted to confirm the bonding chemistry and purity of filler. The inherent thick nature of PSF generated sponge-like shape while the instantaneous demixing process produced finger-like pore networks in HA/PSF-based asymmetric membranes as exhibited by scanning electron microscope (SEM) micrographs. The FTIR spectra confirmed noncovalent weak attractions toward the polymer surface. The leaching ratio was evaluated to observe the dispersion behavior of HA filler in membrane composition. Hydrophilicity, pore profile, pure water permeation (PWP) flux, and molecular weight cutoff (MWCO) values of all formulated membranes were also calculated. Antifouling results revealed that HA modified PSF membranes exhibited 43% less adhesion of bovine serum albumin (BSA) together with >86% recovery of flux. Membrane composition showed 74% total resistance, out of which 60% was reversible resistance. Biocompatibility evaluation revealed that the modified membranes exhibited prothrombin time (PT), and thrombin time (TT) comparable with typical blood plasma, whereas proliferation of living cells over membrane surface proved its nontoxic behavior toward biomedical application. The urea and creatinine showed effective adsorption aptitude toward HA loaded PSF membranes.
A series of 1-(2,3-dihydro-1H-indan-1-yl)-3-aryl urea/thiourea derivatives (4a-j) have been synthesized from the reaction of 2,3-dihydro-1H-inden-1-amine (2) with various aryl isocyanates/isothiocyanates (3a-j) by using N,N-DIPEA base (Hunig's base) catalyst in THF at reflux conditions. All of them are structurally confirmed by spectral (IR, 1H &13C NMR and MASS) and elemental analysis and screened for their in-vitro antioxidant activity against DPPH and NO free radicals and found that compounds 4b, 4i, 4h &4g are potential antioxidants. The obtained in vitro results were compared with the molecular docking, ADMET, QSAR and bioactivity study results performed for them and identified that the recorded in silico binding affinities were observed in good correlation with the in vitro antioxidant results. The Molecular docking analysis had unveiled the strong hydrogen bonding interactions of synthesized ligands with ARG 160 residue of protein tyrosine kinase (2HCK) enzyme and plays an effective role in its inhibition. Toxicology studies have assessed the potential risks of 4a-j and inferred that all of them were in the limits of potential drugs. The conformational analysis of 4a-j inferred that the urea/thiourea spacer linking 2,3-dihydro-1H-inden-1-amino and substituted aryl units has facilitated all these molecules to effectively bind with ARG 160 amino acid residue present on the α-helix of the protein tyrosine kinase (2HCK) enzyme specifically on chain A of hemopoetic cell kinase. Collectively this study has established a relationship between the antioxidant potentiality and ligands binding with ARG 160 amino acid residue of chain A of 2HCK enzyme to inhibit its growth as well as proliferation of reactive oxygen species in vivo.
A new series of urea/thiourea derivatives have been efficiently synthesized from the reaction of L-3-hydroxytyrosine with selective isocyanates/isothiocyanates and characterized by Infra-red, proton & carbon-13 nuclear magnetic resonance spectral and mass spectrometry studies. All the synthesized compounds have been screened for their antioxidant activity by 1,1-diphenyl1-2-picrylhydrazyl radical assay, ferric reducing antioxidant power assay and also studied their molecular docking interaction profiles against 1N8Q and 3NRZ enzymatic proteins. The in vitro antioxidant activity has further supported by quantitative structure activity relationship, absorption, distribution, metabolism, and excretion & toxicity studies, bioactivity studies & enzyme inhibition assay and identified that they were potentially bound to ASP490 & ASP361 aminoacid residue in chain A of 1N8Q protein and GLN1194 aminoacid residue in chain L of 3NRZ protein and are responsible for potential antioxidant activity. It is proved that urea derivatives linked with 4-fluoro & 4-nitro and thiourea derivatives linked with 3-chloro & 4-fluoro have exhibited promising antioxidant activity. In eventual synthesized compounds have been identified as potential blood-brain barrier penetrable compounds and proficient central nervous system active neuro-protective antioxidant agents as they have envisaged as easily penetrable to blood-brain barrier thresholds, a neuroprotective property.
Fish meal is currently the major protein source for commercial aquaculture feed. Due to its unstable supply and increasing price, fish meal is becoming more expensive and its availability is expected to face significant challenges in the near future. Therefore, feasible alternatives to fish meal are urgently required. Microalgae have been recognized as the most promising candidates to replace fish meal because the protein composition of microalgae is similar to fish meal and the supply of microalgae-based proteins is sustainable. In this study, an indigenous microalga (Chlorella vulgaris FSP-E) with high protein content was selected, and its feasibility as an aquaculture protein source was explored. An innovative photobioreactor (PBR) utilizing cold cathode fluorescent lamps as an internal light source was designed to cultivate the FSP-E strain for protein production. This PBR could achieve a maximum biomass and protein productivity of 699 and 365 mg/L/day, respectively, under an optimum urea and iron concentration of 12.4 mM and 90 μM, respectively. In addition, amino acid analysis of the microalgal protein showed that up to 70% of the proteins in this microalgal strain consist of indispensable amino acids. Thus, C. vulgaris FSP-E appears to be a viable alternative protein source for the aquaculture industry.
Cellulose carbamate (CCs) was produced from kenaf core pulp (KCP) using microwave reactor-assisted method. The effects of urea concentration and reaction time on the formation of nitrogen content in CCs were investigated. The CCs' solubility in LiOH/urea system was determined and its membranes were characterized. As the urea content and reaction time increased, the nitrogen content form in CCs increased which enhanced the CCs' solubility. The formation of CCs was confirmed by Fourier transform infrared spectroscopy (FT-IR) and nitrogen content analysis. The CCs' morphology was examined using Scanning electron microscopy (SEM). The cellulose II and crystallinity index of the membranes were confirmed by X-ray diffraction (XRD). The pore size of the membrane displayed upward trend with respect to the urea content observed under Field emission scanning electron microscope (FESEM). This investigation provides a simple and efficient procedure of CCs determination which is useful in producing environmental friendly regenerated CCs.
Bleached kenaf core pulps (BKC) were hydrolyzed in H2SO4 (0.5M) at different time (0min to 90min) at room temperature. After the hydrolysis process, the viscosity average molecular weight (Mŋ) for BKC sample has reduced from 14.5×10(4) to 2.55×10(4). The hydrolyzed BKC was then dissolved in NaOH:urea:water and in LiOH:urea:water mixed solvent at the ratio of 7:12:81 and 4.6:15:80.4, respectively. The increased in hydrolysis time has decreased Mŋ of cellulose leading to easy dissolution process. Higher porosity and transparency with lower crystallinity index (CrI) of regenerated membrane produced can be achieved as the Mŋ reduced. The properties of membrane were observed through FESEM, UV-vis spectrophotometer and XRD. This study has proven that acid hydrolysis has reduced the Mŋ of cellulose, thus, enhanced the properties of regenerated membrane produced with assisted by alkaline/urea system.
Phytoremediation has been applied as a promising and cost-effective technique for removing nutrient pollutants from wastewater. In this study, the effect of fullerene C60 was assessed on enhancing the phytoremediation efficiency of teak plants over a period of 1 month. Teak plants were supplied with fullerene C60 (0, 25, or 50 mg L-1) and fed daily with two types of urea plant wastewater (with and without adding optimum ratio of phosphorus and potassium). The required volume of wastewater by the teak plants, nitrogen removal percentage, plant growth parameters (plant height, number of leaves, leaf surface area, and dry biomass), and nutrient content was recorded throughout the study. The results showed that addition of 25 mg L-1 fullerene C60 to urea plant wastewater could increase water uptake and nitrogen recovery of the teak plants. Plant growth and nutrient contents of teak plants were also increased in the presence of 25 mg L-1 fullerene C60. However, addition of 50 mg L-1 fullerene C60 to the wastewater decreased the values for water uptake and nitrogen recovery. The findings indicated that addition of proper amount of fullerene C60 to the teak-based remediation system can increase the efficiency of the plants for nitrogen removal.
Coating fertilizer particles with thin films is a possibility to control fertilizer release rates. It is observed that novel urea cross-linked starch-lignin composite thin films, prepared by solution casting, swell on coming into contact with water due to the increase in volume by water uptake by diffusion. The effect of lignin content, varied from 0% to 20% in steps of 5% at three different temperatures (25°C, 35°C and 45°C), on swelling of the film was investigated. By gravimetric analysis, the equilibrium water uptake and diffusion coefficient decrease with lignin content, indicating that the addition of lignin increases the hydrophobicity of the films. When temperature increases, the diffusion coefficient and the amount of water absorbed tend to increase. Assuming that swelling of the thin film is by water uptake by diffusion, the diffusion coefficient is estimated. The estimated diffusion coefficient decreases from 4.3 to 2.1 × 10-7 cm2/s at 25°C, from 5.3 to 2.9 × 10-7 cm2/s at 35°C and from 6.2 to 3.8 × 10-7 cm2/s at 45°C depending on the lignin content. Activation energy for the increase in diffusion coefficient with temperature is observed to be 16.55 kJ/mol. An empirical model of water uptake as a function of percentage of lignin and temperature was also developed based on Fick's law.
This study was designed to optimize the culture conditions of juvenile Epinephelus fuscoguttatus (Forsskål, 1775) under laboratory conditions. To this effect, the rate of oxygen consumption was monitored as an index of stress under different temperature, salinity, pH, photoperiod, and urea concentrations. The result obtained after 12 h of exposure suggests the preference of the juvenile E. fuscoguttatus to a temperature range of 15-25 °C and salinity of 30 ppt. Based on this study, temperature was found to be the most lethal as 100% mortality was observed after 6 h in fish exposure to temperatures above the optimal (≥ 30 °C). However, the oxygen consumption rate was similar under the different pH, photoperiod, and urea concentration tested. It was concluded that water temperature was most critical in terms of respiration physiology of the juvenile E. fuscoguttatus given the range and levels of environmental factors tested in this study.
Dissolved oil palm empty fruit bunch (EFB) cellulose in NaOH/urea solvent was mixed with sodium carboxymethylcellulose (NaCMC) to form a green regenerated superabsorbent hydrogel. The effect of concentration of epichlorohydrin (ECH) as the crosslinker on the formation, physical, and chemical properties of hydrogel was studied. Rapid formation and higher gel content of hydrogel were observed at 10% concentration of ECH. The superabsorbent hydrogel was successfully fabricated in this study with the swelling ability >100,000%. Hydrogel with higher concentration of ECH showed opposite trend by having higher superabsorbent property than that of lower concentration. The covalent bond of COC was observed with Attenuated total reflectance fourier transform infrared (ATR-FT-IR) spectroscopy to confirm the occurrence of crosslinking. The physical and chemical properties of hydrogel were affected by swelling phenomenon. Hydrogel with higher degree of swelling exhibited lower moisture retention and higher transparency. Moreover, the weight of the superabsorbent hydrogel increased with the decrement of pH value of external media (distilled water). This study provided substantial information on the effect of different percentage of ECH as crosslinker on hydrogel basic properties. Furthermore, this study affords correlation of many essential driving forces that affected hydrogel superabsorbent property.
Hydrogels are an attractive platform for drug delivery to the skin. Current cellulose hydrogel developments commonly focus on readily available bleached woody cellulose. Considering the detrimental environmental impacts of bleaching reagents, unbleached non-woody biomass was proposed as an alternative. Herein, this study aims to develop hydrogel from native cellulose extracted from oil palm empty fruit bunches for dermal drug delivery with an emphasis on evaluating the effect of alkali solvent compositions on hydrogel formation. Unbleached dissolving pulps were solubilized in alkali solvents containing sodium hydroxide (NaOH) (6-8%w/v) and urea (4-6%w/v) before crosslinking. Hydrogels were loaded with ibuprofen for skin permeation studies. Light brownish hydrogels formed are aesthetically acceptable and biodegradable with low cytotoxicity. NaOH content has a dominant role over urea where thinner and deformable crosslinked network walls in a porous hydrogel structure are associated with high NaOH content. Synergistic effects (cellulose solubility: 94 %; swelling ratio: ~2800 %) were observed at 7%w/v NaOH and 4%w/v urea with low toxicity. Most hydrogels showed >80 % of ibuprofen permeated into the skin and this increased with the swelling ratio of hydrogels. Unbleached cellulose pulps have excellent potential for hydrogel fabrication with outstanding physicomechanical properties for dermal drug delivery.
With the exponential growth of the global population, the agricultural sector is bound to use ever larger quantities of fertilizers to augment the food supply, which consequently increases food production costs. Urea, when applied to crops is vulnerable to losses from volatilization and leaching. Current methods also reduce nitrogen use efficiency (NUE) by plants which limits crop yields and, moreover, contributes towards environmental pollution in terms of hazardous gaseous emissions and water eutrophication. An approach that offsets this pollution while also enhancing NUE is the use of controlled release urea (CRU) for which several methods and materials have been reported. The physical intromission of urea granules in an appropriate coating material is one such technique that produces controlled release coated urea (CRCU). The development of CRCU is a green technology that not only reduces nitrogen loss caused by volatilization and leaching, but also alters the kinetics of nitrogen release, which, in turn, provides nutrients to plants at a pace that is more compatible with their metabolic needs. This review covers the research quantum regarding the physical coating of original urea granules. Special emphasis is placed on the latest coating methods as well as release experiments and mechanisms with an integrated critical analyses followed by suggestions for future research.
In this study, difatty acyl urea has been successfully synthesized from corn oil using sodium ethoxide as a catalyst. Ethyl fatty ester and glycerol were produced as by-products. In this reaction, corn oil was refluxed with urea in ethanol. The highest conversion percentage (78%) was obtained when the process was carried out for 8 hours using urea to corn oil ratio of 5.6: 1.0 at 78 degrees C. Both difatty acyl urea and ethyl fatty ester have been characterized using elemental analysis, Fourier transform infrared (FTIR) spectroscopy and (1)H nuclear magnetic resonance (NMR) technique.
N,N'-Carbonyl difatty amides (CDFAs) have been synthesized from palm oil using sodium ethoxide as catalyst. Ethyl fatty esters (EFEs) were produced as a by-product as well as glycerol. The synthesis was carried out by reflux palm oil and urea in presence of ethanol. In this process, palm oil gave 79% pure CDFAs after 8 hours and molar ratio of urea to palm oil was 6.2: 1 at 78 degrees C. Both CDFAs and EFEs have been characterized using elemental analysis, Fourier transform infrared (FTIR) spectroscopy and (1)H nuclear magnetic resonance (NMR) technique.
The Lipase-catalyzed synthesis of glyceryl monocaffeate (GMC) in choline chloride-urea of natural deep eutectic solvent (NADES) media is reported to provide amphiphilic character to caffeic acid (CA). The modification of CA into GMC could potentially increase its solubility and widen the application of CA's biological activities in water and oil-based systems. The high conversion was achieved when the reaction was carried out with the addition of more than 20 %v/v water, at a high molar ratio of glycerol and 40°C. It was found that the lipase-catalyzed transesterification of ethyl caffeate (EC) and glycerol in choline chloride-urea of DES media obeyed ping-pong bi-bi mechanism with Vmax = 10.9 mmol.min-1, KmEC = 126.5 mmol and KmGly = 1842.7 mmol.
Diopside was synthesized from biowaste (Eggshell) by sol-gel combustion method at low calcination temperature and the influence of two different fuels (urea, l-alanine) on the phase formation temperature, physical and biological properties of the resultant diopside was studied. The synthesized materials were characterized by heating microscopy, FTIR, XRD, BET, SEM and EDAX techniques. BET analysis reveals particles were of submicron size with porosity in the nanometer range. Bone-like apatite deposition ability of diopside scaffolds was examined under static and circulation mode of SBF (Simulated Body Fluid). It was noticed that diopside has the capability to deposit HAP (hydroxyapatite) within the early stages of immersion. ICP-OES analysis indicates release of Ca, Mg, Si ions and removal of P ions from the SBF, but in different quantities from diopside scaffolds. Cytocompatability studies on human bone marrow stromal cells (hBMSCs) revealed good cellular attachment on the surface of diopside scaffolds and formation of extracellular matrix (ECM). This study suggests that the usage of eggshell biowaste as calcium source provides an effective substitute for synthetic starting materials to fabricate bioproducts for biomedical applications.
This paper investigates the dielectric properties of urine in normal subjects and subjects with chronic kidney disease (CKD) at microwave frequency of between 0.2 GHz and 50 GHz. The measurements were conducted using an open-ended coaxial probe at room temperature (25°C), at 30°C and at human body temperature (37°C). There were statistically significant differences in the dielectric properties of the CKD subjects compared to those of the normal subjects. Statistically significant differences in dielectric properties were observed across the temperatures for normal subjects and CKD subjects. Pearson correlation test showed the significant correlation between proteinuria and dielectric properties. The experimental data closely matched the single-pole Debye model. The relaxation dispersion and relaxation time increased with the proteinuria level, while decreasing with the temperature. As for static conductivity, it increased with proteinuria level and temperature.
Urea and thermal denaturations of bovine serum albumin (BSA) were studied in the absence and the presence of honey or simulated honey sugar cocktail (SHSC) using far-UV CD and ANS fluorescence spectroscopy. Presence of 20% (w/v) honey or SHSC in the incubation mixture shifted the urea transition curve towards higher urea concentrations, being higher in the presence of honey and transformed the two-step, three-state transition into a single-step, two-state transition. A comparison of the far-UV CD and the ANS fluorescence spectra of 4.6 M urea-denatured BSA (U-BSA) in the absence and the presence of 20% (w/v) honey or SHSC suggested greater stabilizing potential of honey than SHSC, as U-BSA maintained native like conformation in the presence of 20% (w/v) honey. Furthermore, thermal transition curves of BSA were also shifted towards higher temperature range in the presence of 20% (w/v) SHSC and honey, showing greater shift in the presence of honey. The far-UV CD spectra of the heat-denatured BSA also showed greater stabilization in the presence of honey. Taken together all these results suggested greater protein stabilizing potential of honey than SHSC against chemical and thermal denaturations of BSA.