Measurement of major cation such as Na+, K+, and Ca2+ in water are normally carried out using
AAS, ICP-OES or flame photometry. In this study, an attempt was made to measure these cations
using Energy Dispersive X-ray Fluorescent Spectrometry (EDXRF). Hot spring s water was taken from varies hot spring in Selangor and divided into two portions that is filtered and unfiltered. 5 mL of water samples were pipette into a special liquid cups (sample holders) which has a thin mylar film underneath. The MiniPal4 XRF instrument was used in this study. The resolution for the instrument use is 145 keV with energy resolution at 5.9 keV. The spectrum of cations were analysed by using MiniPal/MiniMate software to determine the cations concentration. For K+ and Ca2+, Al-thin filter was used and default filter was used for Na+. The concentration of Na+ obtained for filtered and unfiltered samples were ranged from 38.00 to 66.05 and 43.26 to 76.95 ppm. Meanwhile, concentrations of K+ for filtered and unfiltered samples were ranged from 2.42 to 8.07 and 6.18 to 29.28 ppm. Concentrations of Ca2+ for filtered and unfiltered samples were ranged from 2.59 to 10.94 and 3.18 to 12.99 ppm.
Background: The COMBI concept is a novel approach by the WHO to control communicable diseases which are influenced by community behaviour. The Ministry of Health is currently evaluating its use against dengue in selected areas throughout Malaysia. COMBI doctrine differs from previous dengue campaigns. It acknowledges that the factors contributing to dengue proliferation may differ between areas. Factors for a given area are analysed, then a single precise behavioural goal to overcome those problems is formulated. To inculcate this behavioural change, the target community is subjected to an intensive campaign using Integrated Marketing Communication techniques adapted from the advertisingindustry, particularly involving volunteers from the community itself.
Methodology: In Selangor the pilot project was implemented in Section 3 and Section 4 of Bandar Baru Bangi, in the district of Hulu Langat. Here, Aedes breeding was found to occur mainly in water containers of semi permanent nature (eg. ‘kolah’, aquatic plant jars, flower pot bases etc). A total of 172 volunteers were recruited to disperse the message of “Suluh – Suluh, Basuh - Basuh” whilst distributing leaflets and flashlights to 2666 homes. Residents were instructed to illuminate such water containers twice weekly and scrub any containers found to contain larvae. The program commenced on 23/5/2004 and lasted 16 weeks.
Results : During this period, the initial Aedes Index of 5 was reduced to 0.96 while combined cases of Dengue Fever / Dengue Haemorraghic Fever in Sections 3 and 4 reported to the Hulu Langat District Health Office also dropped to 1 (unconfirmed).
Conclusion : The COMBI approach in Hulu Langat successfully demonstrated that correct problem identification synergized with community engagement can potentially reduce Aedes proliferationand dengue morbidity.
The aim of this study was to determine the efficiency of different human amniotic membrane (HAM) processing methods on the concentration, purity and integrity of RNA. Two different techniques (Technique1 andTechnique2) were employed for the processing of HAM, which differed in terms of washing solution, sample storage conditions and processing time. Based on preservation of HAM, three groups were formed under each technique. In Technique 1, the groups were fresh frozen 1 (F1), glycerol preserved (GP) and gamma irradiated glycerol preserved (IGP); where else in Technique 2, the groups were fresh frozen 2 (F2), 50%glycerol/Dulbecco’s modified Eagle medium (DMEM) cryopre served HAM diluted with phosphate buffered saline(GB) and 50% glycerol/DMEM cryop reserved HAM diluted with diethyl procarbonate water (GD). Total RNA was extracted from the samples and their concentration, purity and integrity were examined. The F2 sample of which there was no pre-washing step and involved direct sample storage at-80oC, shorter processing time and chilled processing conditions had yielded better quality of RNA compared to the others.
Covalently cross-linked nanogels were prepared via irradiation of inverse micelles that had been preparedfrom radiation crosslinkable polymer, water, oil and surfactant. A mixture of polymer, water, heptane andsodium dioctyl sulfosuccinate (AOT) at certain compositions forms inverse micelles with the size rangingfrom 2 to 8 nm. The hydrophilic head of the surfactant facilitates encapsulation of water soluble polymer.If the entrapped polymer is radiation crosslinkable, it is expected that upon irradiation, polymerizationshall take place in such small and confined space, leading to formation of nano-sized polymeric gel.Meanwhile, emulsion at 2 nm size was chosen for gamma irradiation process. The formation of thenano-sized discreet gel using irradiation of inverse micelles technique was proven at a dose as low as 5kGy to obtain nanogel sized ~ 95 nm.
This study examined the physicochemical properties of rice flours with five different particle sizes (≤63, 80, 100, 125, and 140 μm) prepared by dry milling and their effects on textural properties of laksa noodles. Rice flour with the smallest particle size had the highest water absorption index, peak viscosity, hot paste viscosity, breakdown, final or cold paste viscosity and gel hardness, but the lowest gelatinization temperature. Reduction of rice flour particle size improved textural properties of laksa noodle. Laksa noodle produced from rice flour with the smallest particle size had the best textural properties.
Environmental radiation protection program is important in the effort to limit radiation dose to the public to be as low as reasonably achievable. As water is an important factor of transfer of radionuclide to human, therefore it is important to measure natural radionuclide concentrations in rivers. 20 water samples were collected randomly from the main rivers in Kota Tinggi district. The water samples collected were analysed using ICP-MS technique to determine uranium, thorium and potassium concentration in river water. Radionuclide concentrations obtained were compared with the terrestrial gamma radiation dose rate measured in the area. Significance of the results obtained is discussed.
Field investigation on the operation of an industrial fluidized bed paddy dryer of 25 t/h capacity available in a processing complex of Padiberas Nasional Berhad (BERNAS) of Malaysia was carried out to assess its drying characteristics, energy consumption and quality of product during two paddy harvesting seasons. A grain drying simulation model was used to predict dryer performance which can be used as a basis for improving drying operations. For the first season (August-September), average drying rate was found to be 538 kg moisture/h to reduce moisture content (mc) from 36.98± 0.89% dry basis (db) to 27.58±0.79% (db) at 100-120°C of drying air temperature with a feed rate (capacity) of 7.75 t/h. In the second season (February-March), average drying rate was found to be 435 kg moisture/h to reduce mc from 28.14 ±0.68% (db) to 22.54 ± 0.69% (db) at 78-90°C drying air temperature with a feed rate of 9.5 t/h. The thermal and electrical energy consumptions were obtained as 7.57 and 0.97 MJ/kg water removed, respectively, for the first season, while 5.92 and 1.2 MJ/kg water removed for the second season. Higher head rice yield and whiteness and lower milling recovery were achieved during the first season than the second season at acceptable milling degree and transparency. Meanwhile, simulation results indicated that the dryer performed better in terms of increased drying capacity during the second than the first season; the dryer could be operated at 150°C to achieve almost double throughput capacity up to 20 t/h for the second season, while for the first season, high mc hindered the capacity to be at or below 7.75 t/h even when using higher a temperature of 160°C to reduce moisture to the desired final moisture of 24-25% (db). Proportion of slower vehicles based on users' opinion poll
This paper reviews the literature on uranium contamination and the removal of uranium from wastewater stemming from mining activities and nuclear power generation. After reviewing the applications of uranium in power generation, military, industry and scientific, this review discusses uranium and rare earth elements in wastewaters and the toxicity of uranium on aquatic life and humans. Further, various methods of removal of heavy metal contaminants including uranium are reviewed with special focus on the adsorption process and carbon nanotubes as a superior adsorbent.
Mercury emission into the atmosphere is a global concern due to its detrimental effects on human health in general. The two main sources of mercury emission are natural sources and anthropogenic sources. Mercury emission from natural sources include volcanic activity, weathering of rocks, water movement and biological processes which are obviously inevitable. The anthropogenic sources of mercury emission are from coal combustion, cement production and waste incineration. Thus, in order to reduce mercury emission it is appropriate to investigate how mercury is released from the anthropogenic sources and consequently the mercury removal technology that can be implemented in order to reduce mercury emission into the atmosphere. Many alternatives have been developed to reduce mercury emission and the recent application of activated carbon showed high potential in the adsorption of elemental mercury. This paper discusses the ability of activated carbon and variable parameters that influence mercury removal efficiency in flue gas.
Mixed microbial culture used in this study was developed from sludge that was taken from local textile wastewater treatment tank. Acclimatization process was performed before starting the biodegradation experiment to obtain a microbial culture with high degradation properties. Kinetic studies by the mixed microbial culture were determined quantitatively for the model pollutant, Reactive Black 5 (RB 5). By using Michaelis-Menten model, the constants were found to be 11.15 mg l-1 h -1 and 29.18 mg l-1 for Vm and Km respectively. The values of kinetic constants for Monod model were found to be 33.11 mg l-1 cell h-1 for the maximum specific microbial growth rate, µm and 86.62 mg l-1 for Monod constant, Ks. The effects of process parameters such as pH, inoculum size and initial dye concentration on the biodegradation of azo dye, RB 5 were systematically investigated. Maximum removal efficiencies observed in this study were 75% for pH 6, 100% for 15% inoculum concentration and 75% for 20 ppm of initial dye concentration.
In this study, Hydrolysate from angelwing clam (Pholas orientalis) was produced at 0, 1, 2 and 3 hrs and E/S ratio of 0.5 and 3% using alcalase where the pH and temperature were kept constant at pH 8.5 and 60°C, respectively. The hydrolysates were analysed for antioxidant and functional properties such as solubility, emulsifying properties and water and oil holding capacity. Degree of hydrolysis (DH), yield, functional and antioxidant properties were influenced by the hydrolysis time and E/S ratio. Higher enzyme concentration (E/S 3%) and longer hydrolysis time increased the DH. Yield was higher at E/S 3% but reduced with hydrolysis time. Longer hydrolysis time produced more soluble hydrolysate and higher metal chelating activity but lower in emulsifying properties and DPPH activity. Higher enzyme concentration resulted in increase only in solubility and metal chelating activity. This study revealed that enzymatic hydrolysis using alcalase should be performed at shorter hydrolysis time using intermediate concentration of enzyme (E/S between 0.5 to 3%) in order to produce angelwing clam hydrolysate with collectively good functional and antioxidant properties
Geographic Information System (GIS) and remote sensing are geospatial technologies that have been used for many years in environmental studies, including gathering and analysing of information on the physical parameters of wildlife habitats and modelling of habitat assessments. The home range estimation provided in a GIS environment offers a viable method of quantifying habitat use and facilitating a better understanding of species and habitat relationships. This study used remote sensing, GIS and Analytic Hierarchy Process (AHP) application tools as methods to assess the habitat parameters preference of Asian elephant. Satellite images and topographical maps were used for the environmental and topographical habitat parameter generation encompassing land use-land cover (LULC), Normalized Digital Vegetation Index (NDVI), water sources, Digital Elevation Model (DEM), slope and aspect. The kernel home range was determined using elephant distribution data from satellite tracking, which were then analysed using habitat parameters to investigate any possible relationship. Subsequently, the frequency of the utilization distribution of elephants was further analysed using spatial and geostatistical analyses. This was followed by the use of AHP for identifying habitat preference, selection of significant habitat parameters and classification of criterion. The habitats occupied by the elephants showed that the conservation of these animals would require good management practices within and outside of protected areas so as to ensure the level of suitability of the habitat, particularly in translocation areas.
In this paper, a mathematical model is developed based on mass and momentum balance for carbon dioxide absorption into aqueous ammonia solution. The model is simplified based on the assumption that the CO2 absorption into aqueous ammonia is a pseudo-first-order reaction. Laplace transform method is applied in order to solve the partial differential model equation. Finally, the CO2 molar flux is expressed as a function of partial pressure of CO2, concentration of aqueous ammonia, temperature and gas-liquid contact area. Variation of CO2 molar flux with partial pressure of CO2 and temperature is discussed and a comparison is performed with experimental data from literature. Variation of CO2 molar flux is also shown with gas-liquid contact area. The calculated flux from the model follows the same trend as that of the experimental data reported in literature and the accuracy is within the accepted limit. The mathematical model is very helpful to predict the CO2 molar flux as a function of partial pressure of CO2, concentration of aqueous ammonia, temperature and gas-liquid contact area.
Formalin is a clear solution of 37% formaldehyde in water. It is used in dentistry as a disinfectant, antiseptic and mainly as tissue fixative for preserving biologic specimens for histopathologic examination. The human knowledge on systemic formaldehyde intoxication is inadequate as only few cases of formalin ingestion have been reported. This paper presents a brief communication of the adverse effect of formalin to the human tissue.
This study aim to evaluate antimicrobial efficacy of sodium hypochlorite (NaOCl) and ozonated water against Enterococci faecalis biofilm. The bacterial biofilm was exposed to 2.62%, 1.31% NaOCl and 0.1 ppm ozonated water over a range of time periods. The presence of viable cells was determined by enumeration of colony forming units (CFU). All experiments were repeated four times (n=4). The effectiveness of the agents was compared using nonparametric Kruskal- Wallis test. The result revealed that 2.62% of NaOCl can completely kill E. faecalis biofilm in 15 minutes whereas 1.31 % NaOCl required a longer time to produce such effect. 0.1 ppm ozonated, however, did not exhibit any antimicrobial effect within the period of time tested. From this study, it can be concluded that 0.1 ppm ozonated water was not comparable with 2.62% and 1.31% NaOCl in antimicrobial efficacy against E. faecalis biofilm.
The study examined modified Fenton (FeGAC/H2O2) pretreatment of the antibiotics amoxicillin and cloxacillin in aqueous solution for biological treatment. The treatment was optimized by the response surface methodology (RSM). The optimum operating conditions at pH3 were H2O2/COD molar ratio 2.0, FeGAC dose 3.5 g/L and reaction time 90 min for 87.53% removal of COD, 78.01% removal of TOC, and 98.24% removal of NH3-N. Biodegradability (BOD5/COD ratio) improved from zero to 0.36, indicating the effluent was amenable to biological treatment. Meanwhile, FTIR spectra indicated degradation of the antibiotics. Compared with Fenton or photo-Fenton, modified Fenton (FeGAC/H2O2) was more effective in the pre-treatment of the antibiotics amoxicillin and cloxacillin in aqueous solution for biological treatment.
A Pressurized Liquid Extraction (PLE) method was developed by using conventional High Performance
Liquid Chromatography (HPLC). It was found that all of the PAHs have been successfully extracted with dichloromethane-acetone with high percentage recovery. A high temperature of 180°C gave the highest recovery for fluoranthene (94.4%). Meanwhile, fluorene showed the highest recovery at 150 bar, with 94.6% recovery. It is noted that there is no significant day-to-day difference in the efficiency of the developed method, with the R.S.D. values averaging at 0.02. The optimized conditions applied to the soil samples were analysed using the High Temperature High Performance Liquid Chromatography (HT-HPLC) with chromatographic conditions: Octadecylsilyl-silica (ODSsilica) column (100 mm × 4.6 mm I.D.); mobile phase acetonitrile:water 40:60 (v/v); flow rate 2.5 mL/min; temperature 70°C; UV absorbance 254 nm; injection volume 5µL.
The removal of heavy metals like lead, copper and cadmium from wastewater streams is an important environmental issue. The capability of immobilized Pycnoporus sanguineus (P. sanguineus), a white-rot macrofungi to remove heavy metals from aqueous solution in a packed bed column was investigated. Lead (Pb (II)) biosorption by immobilized cells of P. sanguineus was investigated in a packed bed column. The experiments were carried out by considering the effect of bed height (5-13 cm), flow rate (4-12 ml min-1) and initial lead (II) concentration (50-300 mg L-1). The breakthrough profiles showed that the saturation of metal ions was achieved faster for 5 cm bed height and 12 ml min-1 influent flow rate. However, the breakthrough time decreased as the initial metal concentration increased from 50 to 300 mg L-1. The column was regenerated using 0.1M HCl solution and biosorptiondesorption studies were carried out for 2 cycles. The results showed that the breakthrough time decreased as the number of cycle was proceeded.
In this study, various methods and applications of flat plate solar collectors are discussed and pictorial representations are presented. Low temperature applications of flat plate collectors are identified in solar cooking, solar water heating, space and air heating, industrial heating plants and in agricultural produce drying processes. Basic equations, as presented by many researchers in the performances of flat plate collectors, are also presented. The review discusses the analysis of losses from flat plate collectors towards obtaining the overall heat loss coefficient which indicate the performance of flat plate collectors.
A study on the distribution of Recent Ostracoda in offshore sediment was carried out around the South China Sea. A total of 30 sediment samples were taken from the sampling stations between latitude 1°48’ and 7°25’N and longitude 102°09’ and 105°16’E. From this study, 79 species of ostracods belonging to 16 families and 44 genera were identified. The dominant species was Foveoleberis cypraeoides with 937 individuals obtained. There were 13 to 43 species in total. Diversity Index, H(s), was in the range of 2.1 to 3.3, whereas the dominance values were between 4.4 and 14.7%. Several environmental parameters were measured including depth, temperature and salinity. The range values for each of these parameters are 13-72 m, 25.24-30.06o C and 27.74-34.91 ppt, respectively. The sediment texture in this study area can be categorized as sand, sandy mud, clayey mud, silty mud, silty clay, clayey sand, clayey silt and silty sand. The observations revealed that abundance and diversity of ostracod appeared to be principally controlled by depth. Two faunal assemblages were identified in terms of faunal composition, namely, shallow water (Hemikrithe orientalis, Neomonoceratina iniqua, Stigmatocythere indica, Cytherelloidea leroyi and Neocytheretta snellii) and deep water (Paracypris sp., Alataconcha pterogona, Bythocytheropteron alatum, Keijella paucipunctata and Actinocythereis scutigera). A comparative analysis showed a high degree resemblance between the study area and south-eastern Malay Peninsula (the South China Sea).