In this paper, the unsteady stagnation-point boundary layer flow and heat transfer of a special third grade fluid past a permeable stretching/shrinking sheet has been studied. Similarity transformation is used to transform the system of boundary layer equations which is in the form of partial differential equations into a system of ordinary differential equations. The system of similarity equations is then reduced to a system of first order differential equations and has been solved numerically by using the bvp4c function in Matlab. The numerical solutions for the skin friction coefficient and heat transfer coefficient as well as the velocity and temperature profiles are presented in the forms of tables and graphs. Dual solutions exist for both cases of stretching and shrinking sheet. Stability analysis is performed to determine which solution is stable and valid physically. Results from the stability analysis depict that the first solution (upper branch) is stable and physically realizable, while the second solution (lower branch) is unstable.
Hybrid reinforcement's novel composite (Al-Fe3O4-SiC) via powder metallurgy method was successfully fabricated. In this study, the aim was to define the influence of SiC-Fe3O4 nanoparticles on microstructure, mechanical, tribology, and corrosion properties of the composite. Various researchers confirmed that aluminum matrix composite (AMC) is an excellent multifunctional lightweight material with remarkable properties. However, to improve the wear resistance in high-performance tribological application, hardening and developing corrosion resistance was needed; thus, an optimized hybrid reinforcement of particulates (SiC-Fe3O4) into an aluminum matrix was explored. Based on obtained results, the density and hardness were 2.69 g/cm3, 91 HV for Al-30Fe3O4-20SiC, after the sintering process. Coefficient of friction (COF) was decreased after adding Fe3O4 and SiC hybrid composite in tribology behaviors, and the lowest COF was 0.412 for Al-30Fe3O4-20SiC. The corrosion protection efficiency increased from 88.07%, 90.91%, and 99.83% for Al-30Fe3O4, Al-15Fe3O4-30SiC, and Al-30Fe3O4-20SiC samples, respectively. Hence, the addition of this reinforcement (Al-Fe3O4-SiC) to the composite shows a positive outcome toward corrosion resistance (lower corrosion rate), in order to increase the durability and life span of material during operation. The accomplished results indicated that, by increasing the weight percentage of SiC-Fe3O4, it had improved the mechanical properties, tribology, and corrosion resistance in aluminum matrix. After comparing all samples, we then selected Al-30Fe3O4-20SiC as an optimized composite.
The problem of stagnation point flow over a stretching/shrinking sheet immersed in a micropolar fluid is analyzed
numerically. The governing partial differential equations are transformed into a system of ordinary (similarity) differential
equation and are then solved numerically using the boundary value problem solver (bvp4c) in Matlab software. The
effects of various parameters on the velocity and the angular velocity as well as the skin friction coefficient and the couple
stress are shown in tables and graphs. The noticeable results are found that the micropolar and the slip parameters
decrease the skin friction coefficient and the couple stress in the existence of magnetic field. Dual solutions appear for
certain range of the shrinking strength. A stability analysis is performed to determine which one of the solutions is stable.
Practical applications include polymer extrusion, where one deals with stretching of plastic sheets and in metallurgy
that involves the cooling of continuous strips.
The three dimensional free convection boundary layer flow near a stagnation point region is embedded in viscous nanofluid with the effect of g-jitter is studied in this paper. Copper (Cu) and aluminium oxide (Al2O3) types of water base nanofluid are cho- sen with the constant Prandtl number, Pr=6.2. Based on Tiwari-Das nanofluid model, the boundary layer equation used is converted into a non-dimensional form by adopting non- dimensional variables and is solved numerically by engaging an implicit finite-difference scheme known as Keller-box method. Behaviors of fluid flow such as skin friction and Nusset number are studied by the controlled parameters including oscillation frequency, amplitude of gravity modulation and nanoparticles volume fraction. The reduced skin friction and Nusset number are presented graphically and discussed for different values of principal curvatures ratio at the nodal point. The numerical results shows that, in- crement occurs in the values of Nusset number with the presence of solid nanoparticles together with the values of the skin friction. It is worth mentioning that for the plane stagnation point there is an absence of reduced skin friction along the y-direction where as for axisymmetric stagnation point, the reduced skin friction for both directions are the same. As nanoparticles volume fraction increased, the skin friction increased as well as the Nusset number. The results, indicated that skin frictions of copper are found higher than aluminium oxide.
In the moving layer of particles with variable concentration, the shear estimation is not directly predictable and there is no existing clear mathematical or empirical formula to achieve this objective. This paper presents a developed approach to estimate the shear forces in a flow having suspended and moving layers of solid particles in liquid flow. The two-layer approach was taken whereby the flow consisting of one upper suspended layer of particles in the liquid, and the bottom layer was the moving bed of particles. In the present work, the method of finding the force acting on the pipe wall by the particles in the layer, termed as the ‘dry force’, was presented using a “pseudo hydrostatic pressure” method. To attain the equation for the dry force, a mathematical approach is taken with the assumptions that the flow is horizontal, two-phase pipe flow (solid in Newtonian liquid), incompressible and it is at steady-state. The analysis was conducted considering various particles densities, various concentrations in the suspended layer and different thicknesses of the moving bed. Changing the concentration in the suspended layer from 0.00001 up to 0.001 didn’t showed significant changes in the dry force evaluation. The dry friction force is increasing with increasing moving bed thickness. The developed mathematical model can be
applicable in solving for the shear force in horizontal solid liquid two-phase flows.
The joining of ceramic-metal could be done through a few techniques: brazing, diffusion bonding, friction welding etc. However, the mechanism of ceramic-metal joining was still not properly understood. In this study, alumina rod was bonded to mild steel rod via friction welding technique by using Al 1100 sheet as interlayer. The diameter of the rods was 10 mm. Friction pressure of 20 MPa and forging pressure of 40 MPa were used. Rotational speeds were maintained at 900 rpm and friction times of 2 to 20 seconds were applied. The joining strength was determined through four point bending test. The maximum bending strength, 240 MPa was obtained at the friction times of 20 seconds. Under optical microscope and SEM observation, the deformation of the aluminum interface was clearly obtained. Mechanical interlocking and close contact between the aluminaaluminum and aluminum-mild steel were observed at magnifications of 3000X. The strength of alumina-steel bonding is much dependent on the wettability of the alumina surface by the molten aluminum and the existing of mechanical interlocking between interlayer and sample materials.
The long term objective of this research is to look into the possibility of replacing soil strength parameters such as cohesion and angle of friction with electrical resistivity value for the purpose of computing among others, factor of safety in slopes or bearing capacity of soil. This paper however is limited to the investigation of correlation between electrical resistivity with some selected soil parameters. Electrical resistivity tests, using a basic multi meter, steel moulds and other related equipment, were conducted in the laboratory on soil samples with variations in soil type, compaction energy and moisture content. The samples consisted of predominantly clay, silt and sandy size particles and were compacted in a 100 x 100 mm square mould, while the corresponding electrical resistivity tests were carried out using the disc electrode method in accordance to BS 1377. The values of the electrical parameters such as voltage, current and resistance, with the corresponding value of soil parameters such as cohesion, angle of friction and moisture content, were measured and recorded. The results of the tests produced some initial crude relationships between electrical resistivity and the selected soil parameters. The strongest correlation between electrical resistivity and angle of internal friction, φ, was obtained from the clay size samples with R2 of 0.824, while the maximum correlation between electrical resistivity and moisture content again was obtained through the clay samples with R2 of 0.818. From the other results and graphs analyzed, some consistencies and specific trends of behaviour observed gave some early indications that a more detail and precise correlation between electrical resistivity and soil strength parameters could be very well possible in future.
A steady laminar mixed convection boundary layer flow about an isothermal solid sphere embedded in a porous medium filled with a nanofluid has been studied for both cases of assisting and opposing flows. The transformed boundary layer equations were solved numerically using an implicit finite-difference scheme. Three different types of nanoparticles, namely Cu, Al2O3 and TiO2 in water-based fluid were considered. Numerical solutions were obtained for the skin friction coefficient, the velocity and temperature profiles. The features of the flow and heat transfer characteristics for various values of the nanoparticle volume fraction and the mixed convection parameters were analyzed and discussed.
Dry sliding wear of polyester hybrid composites containing carboxylic functionalized multi-walled carbon nanotubes (cNT) and microparticles, silica (Si02) was studied at different sliding distances. An attempt has been made to produce uniform dispersion of nano- and micro- particles in the test samples by ultrasonication. The tribological properties of the hybrid composites were performed by using pin-on-disc (POD) tester against grey cast iron countersurface. The dry sliding wear tests were carried out under pressure-velocity (pv) condition of 0.4 MPa and 4 m/s for total sliding distance of 28800 m and at an interval of every sliding distance of 3600 m, wear properties and behavior were studied. The samples containing 10 wt.% silica (microparticles) with and without CNT always show increase in coefficient of friction at the expense of wear rate. However, samples containing only ci'rr have the lowest wear rate with the increase in coefficient of friction. Sliding distance studies also provide the information on wear rates which were ever changing at different sliding distances whereas average coefficient of friction did not vary throughout the tests. SEM observations of wear surfaces showed different wear morphologies when reinforcement (cNT or Si02) incorporated into the composites either alone or in combination.
A combined similarity-numerical solution of the magnetohydrodynamic boundary layer slip flow of an electrically conducting non-Newtonian power-law nanofluid along a heated radiating moving vertical plate is explored. Our nanofluid model incorporates the influences of the thermophoresis and the Brownian motion. The basic transport equations are made dimensionless first and then suitable similarity transformations are applied to reduce them into a set of nonlinear ordinary differential equations with the associated boundary conditions. The reduced equations are then solved numerically. Graphical results for the non-dimensional flow velocity, the temperature and the nanoparticles volume fraction profiles as well as for the friction factor, the local Nusselt and the Sherwood numbers are exhibited and examined for various values of the controlling parameters to display the interesting aspects of the solutions. It was found that the friction factor increases with the increase of the magnetic field (M), whilst it is decreased with the linear momentum slip parameter (a). The linear momentum slip parameter (a) reduces the heat transfer rates and the nanoparticles volume fraction rates. Our results are compatible with the existing results for a special case.
This paper delves into the problem of mixed convection boundary layer flow from a horizontal circular cylinder filled in
a Jeffrey fluid with viscous dissipation effect. Both cases of cooled and heated cylinders are discussed. The governing
equations which have been converted into a dimensionless form using the appropriate non-dimensional variables are solved
numerically through the Keller-box method. A comparative study is performed and authentication of the present results
with documented outcomes from formerly published works is excellently achieved. Tabular and graphical representations
of the numerical results are executed for the specified distributions, considering the mixed convection parameter, Jeffrey
fluid parameters and the Prandtl and Eckert numbers. Interestingly, boundary layer separation for mixed convection
parameter happens for some positive (assisting flow) and negative (opposing flow) values. Strong assisting flow means
the cylinder is heated, which causes the delay in boundary layer separation, whereas strong opposing flow means the
cylinder is cooled, which conveys the separation point close to the lower stagnation point. Contradictory behaviours
of both Jeffrey fluid parameters are observed over the velocity and temperature profiles together with the skin friction
coefficient and Nusselt number. The increase of the Prandtl number leads to the decrement of the temperature profile,
while the increase of the Eckert number results in the slight increment of the skin friction coefficient and decrement of
the Nusselt number. Both velocity and temperature profiles of Eckert number show no effects at the lower stagnation
point of the cylinder.
Closed form solutions for unsteady free convection flows of a second grade fluid near an isothermal vertical plate oscillating in its plane using the Laplace transform technique are established. Expressions for velocity and temperature are obtained and displayed graphically for different values of Prandtl number Pr, thermal Grashof number Gr, viscoelastic parameter α, phase angle ωτ and time τ. Numerical values of skin friction τ 0 and Nusselt number Nu are shown in tables. Some well-known solutions in literature are reduced as the limiting cases of the present solutions.
In this article, an approximate analytical solution of flow and heat transfer for a viscoelastic fluid in an axisymmetric channel with porous wall is presented. The solution is obtained through the use of a powerful method known as Optimal Homotopy Asymptotic Method (OHAM). We obtained the approximate analytical solution for dimensionless velocity and temperature for various parameters. The influence and effect of different parameters on dimensionless velocity, temperature, friction factor, and rate of heat transfer are presented graphically. We also compared our solution with those obtained by other methods and it is found that OHAM solution is better than the other methods considered. This shows that OHAM is reliable for use to solve strongly nonlinear problems in heat transfer phenomena.
The aim of this study is to present an exact analysis of combined effects of radiation and chemical reaction on the magnetohydrodynamic (MHD) free convection flow of an electrically conducting incompressible viscous fluid over an inclined plate embedded in a porous medium. The impulsively started plate with variable temperature and mass diffusion is considered. The dimensionless momentum equation coupled with the energy and mass diffusion equations are analytically solved using the Laplace transform method. Expressions for velocity, temperature and concentration fields are obtained. They satisfy all imposed initial and boundary conditions and can be reduced, as special cases, to some known solutions from the literature. Expressions for skin friction, Nusselt number and Sherwood number are also obtained. Finally, the effects of pertinent parameters on velocity, temperature and concentration profiles are graphically displayed whereas the variations in skin friction, Nusselt number and Sherwood number are shown through tables.
The steady boundary layer flow of a viscous and incompressible fluid over a moving vertical flat plate in an external moving fluid with viscous dissipation is theoretically investigated. Using appropriate similarity variables, the governing system of partial differential equations is transformed into a system of ordinary (similarity) differential equations, which is then solved numerically using a Maple software. Results for the skin friction or shear stress coefficient, local Nusselt number, velocity and temperature profiles are presented for different values of the governing parameters. It is found that the set of the similarity equations has unique solutions, dual solutions or no solutions, depending on the values of the mixed convection parameter, the velocity ratio parameter and the Eckert number. The Eckert number significantly affects the surface shear stress as well as the heat transfer rate at the surface.
One of the difficulties with bobbin friction stir welding (BFSW) has been the visualisation of microstructure, particularly grain boundaries, and this is especially problematic for materials with fine grain structure, such as AA6082-T6 aluminium as here. Welds of this material were examined using optical microscopy (OM) and electron backscatter diffraction (EBSD). Results show that the grain structures that form depend on a complex set of factors. The motion of the pin and shoulder features transports material around the weld, which induces shear. The shear deformation around the pin is non-uniform with a thermal and strain gradient across the weld, and hence the dynamic recrystallisation (DRX) processes are also variable, giving a range of observed polycrystalline and grain boundary structures. Partial DRX was observed at both hourglass boundaries, and full DRX at mid-stirring zone. The grain boundary mapping showed the formation of low-angle grain boundaries (LAGBs) at regions of high shear as a consequence of thermomechanical nature of the process.
Coastal accretion and erosion are unavoidable processes as some coastal sediments undergo modification and stabilization. This study was conducted to investigate the geotechnical behavior of soil collected from Bagan Lalang coast and treated with lime, cement, and rice husk ash (RHA) to design a low-cost alternative mixture with environmentally friendly characteristics. Laboratory tests were carried out to analyze the physical properties of the soil (Atterberg limits and compaction properties), together with mechanical characteristics (direct shear and unconfined compressive strength (UCS) tests) to determine the effect of different ratios of stabilizer/pozzolan on the coastal soil and the optimum conditions for each mixture. Part of the purpose of this study was also to analyze the shear behavior of the coastal soil and monitor the maximum axial compressive stress that the treated specimens can bear under zero confining pressure. Compared to the natural soil, the soil treated with lime and rice husk ash (LRHA) in the ratio of 1:2 (8% lime content) showed a tremendous increase in shear stress under the normal stress of 200 kPa. The strength parameters such as the cohesion (c) and internal friction angle (ϕ) values showed a significant increase. Cohesion values increased considerably in samples cured for 90 days compared to specimens cured for 7 days with additional LRHA in the ratio of 1:2 (28%).
The current work is an attempt to reduce friction coefficient of the treated betelnut fibre reinforced polyester (T-BFRP) composites by aging them in twelve different solutions with different kinematic viscosities. The test will be performed on a pin on disc (POD) wear test rig using different applied loads (5⁻30 N), different sliding distances (0⁻6.72 km) at sliding speed of 2.8 m/s subjected to a smooth stainless steel counterface (AISI-304). Different orientations of the fibre mats such as anti-parallel (AP) and parallel (P) orientations subjected to the rotating counterface will be considered. The worn surfaces were examined through optical microscopy imaging and it was found that the aged specimens had significantly lower damages as compared to neat polyester (NP) and the unaged samples. Besides, P-O samples revealed lower friction coefficients as compared to AP-O, i.e., reduction was about 24.71%. Interestingly, aging solutions with lower kinematic viscosities revealed lower friction coefficients of the aged T-BFRP composites when compared to the ones aged in higher kinematic viscosities.
Free convection flow in a boundary layer region is a motion that results from the interaction of gravity with density differences within a fluid. These differences occur due to temperature or concentration gradients or due to their composition. Studies per- taining free convection flows of incompressible viscous fluids have received much attention in recent years both theoretically (exact or approximate solutions) and experimentally. The situation where the heat be transported to the convective fluid via a bounding sur- face having finite heat capacity is known as Newtonian heating (or conjugate convective flows). In this paper, the unsteady free convection flow of an incompressible viscous fluid between two parallel plates with Newtonian heating is studied. Appropriate non- dimensional variables are used to reduce the dimensional governing equations along with imposed initial and boundary conditions into dimensionless forms. The exact solutions for velocity and temperature are obtained using the Laplace transform technique. The corresponding expressions for skin friction and Nusselt number are also calculated. The graphical results are displayed to illustrate the influence of various embedded parameters such as Newtonian heating parameter and Grashof number. The results show that the effect of Newtonian heating parameter increases the Nusselt number but reduces the skin friction.
Basalt fibre is a promising mineral fibre that has high potential to replace synthetic based glass fibre in today's stringent environmental concern. In this study, friction and wear characteristics of glass and basalt fibres reinforced epoxy composites were studied and comparatively evaluated at two test stages. The first stage was conducted at fixed load, speed and distance under three different conditions; adhesive, abrasive and erosive wear, wherein each composite specimens slide against steel, silicon carbide, and sand mixtures, respectively. The second stage was conducted involving different types of adhesive sliding motions against steel counterpart; unidirectional and reciprocating motion, with the former varied at pressure-velocity (PV) factor; 0.23 MPa·m/s and 0.93 MPa·m/s, while the latter varied at counterpart's configuration; ball-on-flat (B-O-F) and cylinder-on-flat (C-O-F). It was found that friction and wear properties of composites are highly dependent on test conditions. Under 10 km test run, Basalt fibre reinforced polymer (BFRP) composite has better wear resistance against erosive sand compared to Glass fibre reinforced polymer (GFRP) composite. In second stage, BFRP composite showed better wear performance than GFRP composite under high PV of unidirectional sliding test and under B-O-F configuration of reciprocating sliding test. BFRP composite also exhibited better friction properties than GFRP composite under C-O-F configuration, although its specific wear rate was lower. In scanning electron microscopy examination, different types of wear mechanisms were revealed in each of the test conducted.