MyMedR

Displaying publications 21 - 30 of 30 in total

Abstract:

Sort:

Fulltext A study of microstructure and hardness on Fe-Co/SiC composites

Noraziana Parimin, Linus, Andy

Journal of Nuclear and Related Technologies, 2009;2009(1):65-70.
MyJurnal

This research was conducted to study the effect of reinforcement particles on iron-cobalt (FeCo) composites. The composition of silicon carbide (SiC) was varied from 0 to 20 wt%. The composite was fabricated via powder metallurgy (PM) method, which consists of mixing, compaction and sintering processes. The powder was mixed for 2 hours to obtain uniformity between SiC and Fe-Co matrix and compacted to a cylindrical shape at 250 MPa. Samples were sintered for 2 hours at 900 o C with 10 o C/minute heating rate in argon atmosphere. The influences of reinforcement particle on the sintered samples were characterized in terms of microstructure and hardness testing. The Fe-Co/20wt%SiC composites show highest hardness value.

Matched MeSH terms: Metallurgy
Effect of Milling Time on the Microstructure, Physical and Mechanical Properties of Al-Al₂O₃ Nanocomposite Synthesized by Ball Milling and Powder Metallurgy

Toozandehjani M, Matori KA, Ostovan F, Abdul Aziz S, Mamat MS

Materials (Basel), 2017 Oct 26;10(11).
PMID: 29072632 DOI: 10.3390/ma10111232

The effect of milling time on the morphology, microstructure, physical and mechanical properties of pure Al-5 wt % Al₂O₃ (Al-5Al₂O₃) has been investigated. Al-5Al₂O₃ nanocomposites were fabricated using ball milling in a powder metallurgy route. The increase in the milling time resulted in the homogenous dispersion of 5 wt % Al₂O₃ nanoparticles, the reduction of particle clustering, and the reduction of distances between the composite particles. The significant grain refining during milling was revealed which showed as a reduction of particle size resulting from longer milling time. X-Ray diffraction (XRD) analysis of the nanocomposite powders also showed that designated ball milling contributes to the crystalline refining and accumulation of internal stress due to induced severe plastic deformation of the particles. It can be argued that these morphological and microstructural variations of nanocomposite powders induced by designated ball milling time was found to contribute to an improvement in the density, densification, micro-hardness (HV), nano-hardness (HN), and Young's modulus (E) of Al-5Al₂O₃ nanocomposites. HV, HN, and E values of nanocomposites were increased by ~48%, 46%, and 40%, after 12 h of milling, respectively.

Matched MeSH terms: Metallurgy
Fulltext Palm oil derived trimethylolpropane triesters synthetic lubricants and usage in industrial metalworking fluid

Chang TS, Yunus R, Rashid U, Choong TS, Awang Biak DR, Syam AM

J Oleo Sci, 2015;64(2):143-51.
PMID: 25748374 DOI: 10.5650/jos.ess14162

Trimethylolpropane triesters are biodegradable synthetic lubricant base oil alternative to mineral oils, polyalphaolefins and diesters. These oils can be produced from trimethylolpropane (TMP) and fatty acid methyl esters via chemical or enzymatic catalyzed synthesis methods. In the present study, a commercial palm oil derived winter grade biodiesel (ME18) was evaluated as a viable and sustainable methyl ester source for the synthesis of high oleic trimethylolpropane triesters (HO-TMPTE). ME18 has fatty acid profile containing 86.8% oleic acid, 8.7% linoleic acid with the remaining minor concentration of palmitic acid, stearic acid and linolenic acid. It's high oleic property makes it superior to produce synthetic lubricant base oil that fulfills both the good low temperature property as well as good oxidative stability. The synthetic base oil produced had a viscosity of 44.3 mm(2)/s at 40°C meeting the needs for ISO 46 oils. It also exhibited an excellent viscosity index of 219 that is higher than some other commercial brands of trimethylolpropane trioleate. Properties of base oil such as cloud point, density, acid value, demulsibility and soap content were also examined. The oil was then used in the formulation of tapping oil and appraised in term of adaptability, stability and field test performance.

Matched MeSH terms: Metallurgy*
Sorption of Cr(VI), Cu(II) and Pb(II) by growing and non-growing cells of a bacterial consortium

Sannasi P, Kader J, Ismail BS, Salmijah S

Bioresour Technol, 2006 Mar;97(5):740-7.
PMID: 16324841

This paper reports the sorption of three metallic ions, namely Cr(VI), Cu(II) and Pb(II) in aqueous solution by a consortium culture (CC) comprising an acclimatised mixed bacterial culture collected from point and non-point sources. Metal sorption capability of growing and non-growing cells at initial pH of between 3 and 8 in the 1-100mg/L concentration range were studied based on Q(max) and K(f) values of the Langmuir and linearised Freundlich isotherm models, respectively. Maximal metal loading was generally observed to be dependent on the initial pH. Growing cells displayed significant maximal loading (Q(max)) for Pb(II) (238.09 mg/g) and Cu(II) (178.87 mg/g) at pH 6 and at pH 7 for Cr(VI) (90.91 mg/g) compared to non-growing cells (p < 0.05). At the pH range of 6-8, growing cells showed higher loading capacity compared to non-growing cells i.e. 38-52% for Cr, 17-28% for Cu and 3-17% for Pb. At lower metal concentrations and at more acidic pH (3-4) however, non-growing cells had higher metal loading capacity than growing cells. The metal sorption capacity for both populations were as follows: Pb(II) > Cu(II) > Cr(VI).

Matched MeSH terms: Metallurgy*
Fulltext Numerical analysis of thermal conductive hybrid nanofluid flow over the surface of a wavy spinning disk

Ahmadian A, Bilal M, Khan MA, Asjad MI

Sci Rep, 2020 Nov 02;10(1):18776.
PMID: 33139760 DOI: 10.1038/s41598-020-75905-w

A three dimensional (3D) numerical solution of unsteady, Ag-MgO hybrid nanoliquid flow with heat and mass transmission caused by upward/downward moving of wavy spinning disk has been scrutinized. The magnetic field has been also considered. The hybrid nanoliquid has been synthesized in the presence of Ag-MgO nanoparticles. The purpose of the study is to improve the rate of thermal energy transmission for several industrial purposes. The wavy rotating surface increases the heat transmission rate up to 15%, comparatively to the flat surface. The subsequent arrangement of modeled equations is diminished into dimensionless differential equation. The obtained system of equations is further analytically expounded via Homotopy analysis method HAM and the numerical Parametric continuation method (PCM) method has been used for the comparison of the outcomes. The results are graphically presented and discussed. It has been presumed that the geometry of spinning disk positively affects the velocity and thermal energy transmission. The addition of hybrid nanoparticles (silver and magnesium-oxide) significantly improved thermal property of carrier fluid. It uses is more efficacious to overcome low energy transmission. Such as, it provides improvement in thermal performance of carrier fluid, which play important role in power generation, hyperthermia, micro fabrication, air conditioning and metallurgical field.

Matched MeSH terms: Metallurgy
Fulltext A delayed unusual presentation of a penetrating foreign body

Lee ST

Singapore Med J, 1992 Jun;33(3):304-5.
PMID: 1631596

Complications resulting from the penetrating percutaneous foreign bodies almost always arise in the early post injury period. Delayed presentations of previous asymptomatic foreign bodies are rare. In this case report, symptoms of tracheal irritation arose seven years following the initial penetrating shrapnel injury to the neck. Computed tomography scans enabled localisation of the foreign body at the tracheal wall and carotid sheath interface. The usefulness of this radiologic modality in the evaluation of the penetrating soft tissue injury is highlighted. A review of the phenomenon of the migrating and asymptomatic foreign body follows.

Matched MeSH terms: Metallurgy
Radiation-induced chromosomal aberrations among TENORM workers: amang- and ilmenite-processing workers of Malaysia

Kandar MZ, Bhari IB

Mutat Res, 1996 Apr 13;351(2):157-61.
PMID: 8622709

The usefulness of peripheral human lymphocytes as a bioindicator for ionizing radiation effect was tested in a survey of Malaysian workers in two industries producing technologically enhanced naturally occurring radioactive material (TENORM). Workers in amang processing plants who have been with the plant for an average of 12.9 years and who were exposed to radioactive dust showed significantly higher frequencies of chromosomal aberration compared to control and even ilmenite-processing workers. Such frequency was not significantly different between workers in ilmenite-processing plant and control. The differences in duration of employment, occupational hygiene, together with the difference in the percentage of 'old' and 'new' aberrations among the groups sampled were used to explain the high chromosomal aberration frequency among amang workers. The presence of significantly high chromosome damage (dicentrics and fragments) in workers who were chronically exposed to doses below 50 mSv per year or 20 mSv per year averaged over 5 years (ICRP, 1991) provided additional experimental data on the dose-effect relationship at these low-dose ranges. The results confirm the usefulness of using human lymphocytes as a bioindicator for chronic exposure to ionizing radiation and in cases where physical radiation detectors are not available.

Matched MeSH terms: Metallurgy*
Fulltext Effect of sintering parameters on physical and mechanical properties of powder injection moulded stainless steel-hydroxyapatite composite

Ramli MI, Sulong AB, Muhamad N, Muchtar A, Arifin A, Mohd Foudzi F, et al.

PLoS One, 2018;13(10):e0206247.
PMID: 30359433 DOI: 10.1371/journal.pone.0206247

The combination of metallic bio-inert material, stainless-steel 316L (SS316L) and a bio-active material, hydroxyapatite (HA) can produce a composite which has superior properties for orthopaedic applications. The main objective of this study is to investigate the effects of sintering temperature and holding time on the physical and mechanical properties of the sintered part. 50wt.% SS316L and 50wt.% HA were mixed with a binder system of palm stearin (PS) and polyethylene (PE) at 61 vol.% powder loading. Rheological properties show a pseudo-plastic behaviour of the feedstock, where viscosity decreases with increasing shear rate. The feedstock was injection moulded into a tensile bar shape while thermal debinding was carried out at 320°C and 500°C. The brown parts were sintered at 1000, 1100, 1200 and 1300°C, with three different sintering times of 1, 3 and 5 hours in the furnace. It was found that the highest sintered density measured was 95.61% of the theoretical density. In addition, the highest hardness and Young's modulus measured were 150.45 HV and 52.61 GPa respectively, which are higher than those of human bone. The lowest percentage of carbon content was 0.022wt.% given by the sample sintered at 1300°C for 1 hour. Therefore, SS316L/HA composite with good mechanical and physical properties was successfully produced through the PIM process.

Matched MeSH terms: Metallurgy/methods
Flexibility and hardness of dental stainless steel wrought wires used in Thailand

Benjakul P, Cheunarrom C, Ongthiemsak C

J Oral Sci, 2001 Mar;43(1):15-9.
PMID: 11383631

Stainless steel wrought wires used as clasp arms for removable partial dentures in Thailand were compared with those used in some other countries (in the as-received condition) in terms of flexibility, Vickers microhardness and composition. The results showed that there were significant differences (P< or =0.05) among the wires. A Japanese stainless steel wire (SK) was obviously different from the others. It had the lowest proportional limit and microhardness, but its flexibility was almost the same. The chemical composition of each wire was not greatly different. The wires were about 18-20 wt% chromium and 8-9 wt% nickel, except for the SK wire, which had about 12 wt% nickel.

Matched MeSH terms: Metallurgy
Fulltext Metal dust exposure and lung function deterioration among steel workers: an exposure-response relationship

Hamzah NA, Mohd Tamrin SB, Ismail NH

Int J Occup Environ Health, 2016 07;22(3):224-232.
PMID: 27392157 DOI: 10.1080/10773525.2016.1207040

BACKGROUND: Metallic dust is a heterogeneous substance with respiratory sensitizing properties. Its long term exposure adversely affected lung function, thus may cause acute or chronic respiratory diseases.
METHODS: A cross-sectional study was conducted in a steel factory in Terengganu, Malaysia to assess the metal dust exposure and its relationship to lung function values among 184 workers. Metal dust concentrations values (Co, Cr, and Ni) for each worker were collected using air personal sampling. Lung function values (FEV1, FVC, and %FEV1/FVC) were determined using spirometer.
RESULTS: Exposure to cobalt and chromium were 1-3 times higher than permissible exposure limit (PEL) while nickel was not exceeding the PEL. Cumulative of chromium was the predictor to all lung function values (FEV1, FVC, and %FEV1/FVC). Frequency of using mask was positively associated with FVC (Adj b = 0.263, P = 0.011) while past respiratory illnesses were negatively associated with %FEV1/FVC (Adj b = -1.452, P = 0.026). Only few workers (36.4%) were found to wear their masks all times during the working hours.
CONCLUSIONS: There was an exposure-response relationship of cumulative metal dust exposure with the deterioration of lung function values. Improvement of control measures as well as proper and efficient use or personal protection equipment while at work could help to protect the respiratory health of workers.

Matched MeSH terms: Metallurgy