Displaying publications 41 - 60 of 176 in total

Abstract:
Sort:
  1. Fulltext Hydroxypropyl Cellulose Based Non-Volatile Gel Polymer Electrolytes for Dye-Sensitized Solar Cell Applications using 1-methyl-3-propylimidazolium iodide ionic liquid
    Khanmirzaei MH, Ramesh S, Ramesh K
    Sci Rep, 2015;5:18056.
    PMID: 26659087 DOI: 10.1038/srep18056
    Gel polymer electrolytes using imidazolium based ionic liquids have attracted much attention in dye-sensitized solar cell applications. Hydroxypropyl cellulose (HPC), sodium iodide (NaI), 1-methyl-3-propylimidazolium iodide (MPII) as ionic liquid (IL), ethylene carbonate (EC) and propylene carbonate (PC) are used for preparation of non-volatile gel polymer electrolyte (GPE) system (HPC:EC:PC:NaI:MPII) for dye-sensitized solar cell (DSSC) applications. The highest ionic conductivity of 7.37 × 10(-3) S cm(-1) is achieved after introducing 100% of MPII with respect to the weight of HPC. Temperature-dependent ionic conductivity of gel polymer electrolytes is studied in this work. XRD patterns of gel polymer electrolytes are studied to confirm complexation between HPC polymer, NaI and MPII. Thermal behavior of the GPEs is studied using simultaneous thermal analyzer (STA) and differential scanning calorimetry (DSC). DSSCs are fabricated using gel polymer electrolytes and J-V centeracteristics of fabricated dye sensitized solar cells were analyzed. The gel polymer electrolyte with 100 wt.% of MPII ionic liquid shows the best performance and energy conversion efficiency of 5.79%, with short-circuit current density, open-circuit voltage and fill factor of 13.73 mA cm(-2), 610 mV and 69.1%, respectively.
    Matched MeSH terms: Calorimetry, Differential Scanning
  2. Fulltext Optimization of natural lipstick formulation based on pitaya (Hylocereus polyrhizus) seed oil using D-optimal mixture experimental design
    Kamairudin N, Gani SS, Masoumi HR, Hashim P
    Molecules, 2014;19(10):16672-83.
    PMID: 25325152 DOI: 10.3390/molecules191016672
    The D-optimal mixture experimental design was employed to optimize the melting point of natural lipstick based on pitaya (Hylocereus polyrhizus) seed oil. The influence of the main lipstick components-pitaya seed oil (10%-25% w/w), virgin coconut oil (25%-45% w/w), beeswax (5%-25% w/w), candelilla wax (1%-5% w/w) and carnauba wax (1%-5% w/w)-were investigated with respect to the melting point properties of the lipstick formulation. The D-optimal mixture experimental design was applied to optimize the properties of lipstick by focusing on the melting point with respect to the above influencing components. The D-optimal mixture design analysis showed that the variation in the response (melting point) could be depicted as a quadratic function of the main components of the lipstick. The best combination of each significant factor determined by the D-optimal mixture design was established to be pitaya seed oil (25% w/w), virgin coconut oil (37% w/w), beeswax (17% w/w), candelilla wax (2% w/w) and carnauba wax (2% w/w). With respect to these factors, the 46.0 °C melting point property was observed experimentally, similar to the theoretical prediction of 46.5 °C. Carnauba wax is the most influential factor on this response (melting point) with its function being with respect to heat endurance. The quadratic polynomial model sufficiently fit the experimental data.
    Matched MeSH terms: Calorimetry, Differential Scanning
  3. Fulltext Epoxidized vegetable oils plasticized poly(lactic acid) biocomposites: mechanical, thermal and morphology properties
    Chieng BW, Ibrahim NA, Then YY, Loo YY
    Molecules, 2014;19(10):16024-38.
    PMID: 25299820 DOI: 10.3390/molecules191016024
    Plasticized poly(lactic acid) PLA with epoxidized vegetable oils (EVO) were prepared using a melt blending method to improve the ductility of PLA. The plasticization of the PLA with EVO lowers the Tg as well as cold-crystallization temperature. The tensile properties demonstrated that the addition of EVO to PLA led to an increase of elongation at break, but a decrease of tensile modulus. Plasticized PLA showed improvement in the elongation at break by 2058% and 4060% with the addition of 5 wt % epoxidized palm oil (EPO) and mixture of epoxidized palm oil and soybean oil (EPSO), respectively. An increase in the tensile strength was also observed in the plasticized PLA with 1 wt % EPO and EPSO. The use of EVO increases the mobility of the polymeric chains, thereby improving the flexibility and plastic deformation of PLA. The SEM micrograph of the plasticized PLA showed good compatible morphologies without voids resulting from good interfacial adhesion between PLA and EVO. Based on the results of this study, EVO may be used as an environmentally friendly plasticizer that can improve the overall properties of PLA.
    Matched MeSH terms: Calorimetry, Differential Scanning
  4. Fulltext Effect of polydextrose on physicochemical properties of threadfin bream (Nemipterus spp) surimi during frozen storage
    Nopianti R, Huda N, Ismail N, Ariffin F, Easa AM
    J Food Sci Technol, 2013 Aug;50(4):739-46.
    PMID: 24425976 DOI: 10.1007/s13197-011-0394-0
    Physicochemical properties of threadfin bream surimi with different levels of polydextrose (3%, 6%, 9% and 12%), raw surimi, raw surimi with addition sodium tripolyphosphate and commercial surimi (sucrose) during 6 months of frozen storage were investigated. The analyses included the measurement of Ca(2+)-ATPase, sulfhydryl contents, protein solubility, sodium dodecyl sulfate polyacrylamide gel electrophoresis, differential scanning calorimetry and scanning electron microscopy. The Ca(2+)-ATPase, sulfhydryl content and protein solubility levels added with 3%, 6%, 9% and 12% polydextrose can be maintained until the 6 months of storage by 47.33%, 41.60% and 51.41%, respectively. Differential scanning calorimetry showed decreases in thermal stabilization of myosin with regard to transition termperature. Analysis by scanning electron microscopy demonstrated that the number of pores formed was increased after storage. This study suggested that surimi stored with the polydextrose as a cryoprotectant was able to maintain physicochemical of surimi better compared to raw surimi with no additives or raw surimi with sodium tripolyphosphate.
    Matched MeSH terms: Calorimetry, Differential Scanning
  5. Fulltext Synthesis and liquid crystalline properties of new diols containing azomethine groups
    Mohammed IA, Sankar G, Khairuddean M, Mohamad AB
    Molecules, 2010 Apr 30;15(5):3260-9.
    PMID: 20657475 DOI: 10.3390/molecules15053260
    A series of new mesogenic azomethine diols were successfully synthesized by condensation reactions between various chloroalkanols and N,N'-bis(4-hydroxy)-benzylidene-o-toluidine (1). The structures of these compounds were confirmed by CHN, FT-IR, (1)H-NMR, and (13)C-NMR spectrophotometer. Their thermotropic liquid crystalline behavior was studied using differential scanning calorimetry (DSC) and polarizing optical microscope (POM). 4,4'-di(4-Hydroxybutoxy)-N-benzylidine-o-tolidine (2a) does not exhibit liquid crystalline properties. A nematic texture was observed for mesogenic diols 2b, and 2d, whereas the diol 2c exhibits a smectic mesophase. The increase of terminal alkyl chain in these mesogenic diols leads to a decrease in the transition temperature.
    Matched MeSH terms: Calorimetry, Differential Scanning
  6. Composition and thermal characteristics of Madhuca longifolia seed fat and its solid and liquid fractions
    Marikkar JM, Ghazali HM, Long K
    J Oleo Sci, 2010;59(1):7-14.
    PMID: 20032594
    This study was to characterize the seed fat from Madhuca longifolia known as Mee fat and its solid and liquid fractions with the objective of distinguishing them. A sample of Mee fat was partitioned into solid and liquid fractions using acetone as the solvent medium. The isolated fractions were compared to the native Mee fat sample with respect to various physico-chemical parameters using standard chemical methods as well as instrumental techniques such as, gas liquid chromatography (GLC), reversed-phase high performance liquid chromatography (RP-HPLC), and differential scanning calorimetry (DSC). Basic analyses indicated that there were wide variations between the native sample and its fractions with respect to iodine value (IV), and slip melting point (SMP). The cloud point (CP) of the liquid fraction was found to be 10.5 degrees C. Fatty acid compositional analyses showed that the proportion of saturated fatty acids (SFA) such as palmitic and stearic went up in the high-melting fraction (HMF) while in low-melting fraction (LMF) the proportion of unsaturated fatty acid (USFA) such as oleic and lenoleic increased. According to the HPLC analyses, Mee fat had a tiacyl glycerol (TAG) sequence similar to that of palm oil. After fractionation, the solid and liquid fractions obtained were found to have TAG profiles very much different from the native sample. Thermal analyses by DSC showed that Mee fat had two-widely separated high and low melting thermal transitions, a feature which was beneficial for the effective separation of solid and liquid fractions. The thermal profiles displayed by the fractions were clearly distinguishable from that of the native sample.
    Matched MeSH terms: Calorimetry, Differential Scanning
  7. Mechanical and thermal properties of hydroxyaptite filled poly (methyl methacrylate) heat processed denture base material
    Mohamed SH, Arifin A, Mohd Ishak ZA, Nizam A, Samsudin AR
    Med J Malaysia, 2004 May;59 Suppl B:25-6.
    PMID: 15468801
    The aim of this study was to evaluate the effect of powder-to-liquid ratio on the glass transition temperature (Tg) and the tensile properties of denture base material prepared from poly (methyl methacrylate) (PMMA) and hydroxyapatite (HA) previously treated with 3-trimethoxysilylpropyl methacrylate (gamma-MPS). Specimens for mechanical testing were prepared by adding composites powder (PMMA, BPO and HA) to the monomer (MMA and EGDMA) followed by hand mixing as in dental laboratory description usage. The glass transition temperature was studied by using differential scanning calorimetry (DSC). It was observed that the tensile properties and the Tg were affected by the powder-to-liquid ratio. The mechanical characterization of the materials were performed by using single edge notch-tension (SEN-T) specimens; the fracture toughness was slightly higher in formulation which contained HA filler compared to commercial denture base material.
    Matched MeSH terms: Calorimetry, Differential Scanning
  8. Phenyl-functionalized magnetic palm-based powdered activated carbon for the effective removal of selected pharmaceutical and endocrine-disruptive compounds
    Wong KT, Yoon Y, Snyder SA, Jang M
    Chemosphere, 2016 Jun;152:71-80.
    PMID: 26963238 DOI: 10.1016/j.chemosphere.2016.02.090
    Triethoxyphenylsilane (TEPS)-functionalized magnetic palm-based powdered activated carbon (MPPAC-TEPS) was prepared and characterized using various spectroscopic methods, and then tested for the removal of bisphenol A, carbamazepine, ibuprofen and clofibric acid. Magnetite film on MPPAC-TEPS was homogeneously coated on the outer surface of palm-based powdered activated carbon (PPAC) through a hydrothermal co-precipitation technique. Followed by silanization of phenyl-functionalized organosilane on MPPAC's magnetic film. As results, micro/mesopore surface area and volume increased without significant pore clogging and iron (Fe) dissolution under the acidic conditions was greatly decreased. The unique structural and chemical features of MPPAC-TEPS were found to be the main reasons for the enhanced adsorption rates and removal capacities of POPs. The presence of electrolytes and different pH values greatly affected the sorption efficiencies. The dominant sorption mechanism of POPs by MPPAC-TEPS was determined to be π-π interaction (physisorption), based on thermodynamic (ΔG°) and differential scanning calorimetry (DSC). Thermal regeneration at a low temperature (350 °C) was an effective method to desorb the retained POPs and enabled to reactivate MPPAC-TEPS with sustained sorption rates and capacities, whereas PPAC was largely exhausted. As a new type of sorbent for POPs, MPPAC-TEPS has operational advantages, such as magnetic separation and stable regeneration.
    Matched MeSH terms: Calorimetry, Differential Scanning
  9. Fulltext Oxygen consumption--a comparison between calculation by Fick's principle and measurement by indirect calorimetry
    Cheong KF, Lee TL
    Med J Malaysia, 1997 Mar;52(1):70-5.
    PMID: 10968056
    Oxygen consumption values calculated by Fick's principle (cVO2) were compared to simultaneously obtained values measured by indirect calorimetry (mVO2) in two groups of patients; post-coronary artery bypass graft (post-CABG) and septic shock. In both groups of patients, oxygen consumption values derived using indirect calorimetry were higher than that from Fick's principle. Whilst the bias obtained between the two methods of measurement were of acceptable amount clinically, the limits of agreement were wide: -57 to 51 ml.min-1.m-2 in the post-CABG group and -101 to 67 ml.min-1.m-2 in the group of septic patients; indicating that significant differences exist between paired individual values such that cVO2 and mVO2 were not interchangeable in this study.
    Matched MeSH terms: Calorimetry
  10. Fulltext Effect on Physical and Mechanical Properties of Conventional Glass Ionomer Luting Cements by Incorporation of All-Ceramic Additives: An In Vitro Study
    Saran R, Upadhya NP, Ginjupalli K, Amalan A, Rao B, Kumar S
    Int J Dent, 2020;2020:8896225.
    PMID: 33061975 DOI: 10.1155/2020/8896225
    Introduction: Glass ionomer cements (GICs) are commonly used for cementation of indirect restorations. However, one of their main drawbacks is their inferior mechanical properties.

    Aim: Compositional modification of conventional glass ionomer luting cements by incorporating two types of all-ceramic powders in varying concentrations and evaluation of their film thickness, setting time, and strength. Material & Methods. Experimental GICs were prepared by adding different concentrations of two all-ceramic powders (5%, 10, and 15% by weight) to the powder of the glass ionomer luting cements, and their setting time, film thickness, and compressive strength were determined. The Differential Scanning Calorimetry analysis was done to evaluate the kinetics of the setting reaction of the samples. The average particle size of the all-ceramic and glass ionomer powders was determined with the help of a particle size analyzer.

    Results: A significant increase in strength was observed in experimental GICs containing 10% all-ceramic powders. The experimental GICs with 5% all-ceramic powders showed no improvement in strength, whereas those containing 15% all-ceramic powders exhibited a marked decrease in strength. Setting time of all experimental GICs progressively increased with increasing concentration of all-ceramic powders. Film thickness of all experimental GICs was much higher than the recommended value for clinical application.

    Conclusion: 10% concentration of the two all-ceramic powders can be regarded as the optimal concentration for enhancing the glass ionomer luting cements' strength. There was a significant increase in the setting time at this concentration, but it was within the limit specified by ISO 9917-1:2007 specifications for powder/liquid acid-base dental cements. Reducing the particle size of the all-ceramic powders may help in decreasing the film thickness, which is an essential parameter for the clinical performance of any luting cement.

    Matched MeSH terms: Calorimetry, Differential Scanning
  11. Fulltext Characterisation of aptamer-anchored poly(EDMA-co-GMA) monolith for high throughput affinity binding
    Acquah C, Chan YW, Pan S, Yon LS, Ongkudon CM, Guo H, et al.
    Sci Rep, 2019 10 10;9(1):14501.
    PMID: 31601836 DOI: 10.1038/s41598-019-50862-1
    Immobilisation of aptameric ligands on solid stationary supports for effective binding of target molecules requires understanding of the relationship between aptamer-polymer interactions and the conditions governing the mass transfer of the binding process. Herein, key process parameters affecting the molecular anchoring of a thrombin-binding aptamer (TBA) onto polymethacrylate monolith pore surface, and the binding characteristics of the resulting macroporous aptasensor were investigated. Molecular dynamics (MD) simulations of the TBA-thrombin binding indicated enhanced Guanine 4 (G4) structural stability of TBA upon interaction with thrombin in an ionic environment. Fourier-transform infrared spectroscopy and thermogravimetric analyses were used to characterise the available functional groups and thermo-molecular stability of the immobilised polymer generated with Schiff-base activation and immobilisation scheme. The initial degradation temperature of the polymethacrylate stationary support increased with each step of the Schiff-base process: poly(Ethylene glycol Dimethacrylate-co-Glycidyl methacrylate) or poly(EDMA-co-GMA) [196.0 °C (±1.8)]; poly(EDMA-co-GMA)-Ethylenediamine [235.9 °C (±6.1)]; poly(EDMA-co-GMA)-Ethylenediamine-Glutaraldehyde [255.4 °C (±2.7)]; and aptamer-modified monolith [273.7 °C (±2.5)]. These initial temperature increments reflected in the associated endothermic energies were determined with differential scanning calorimetry. The aptameric ligand density obtained after immobilisation was 480 pmol/μL. Increase in pH and ionic concentration affected the surface charge distribution and the binding characteristics of the aptamer-modified disk-monoliths, resulting in the optimum binding pH and ionic concentration of 8.0 and 5 mM Mg2+, respectively. These results are critical in understanding and setting parametric constraints indispensable to develop and enhance the performance of aptasensors.
    Matched MeSH terms: Calorimetry, Differential Scanning
  12. Fulltext Thermal and Structural Analysis of Epoxidized Jatropha Oil and Alkaline Treated Kenaf Fiber Reinforced Poly(Lactic Acid) Biocomposites
    Kamarudin SH, Abdullah LC, Aung MM, Ratnam CT
    Polymers (Basel), 2020 Nov 06;12(11).
    PMID: 33171889 DOI: 10.3390/polym12112604
    New environmentally friendly plasticized poly(lactic acid) (PLA) kenaf biocomposites were obtained through a melt blending process from a combination of epoxidized jatropha oil, a type of nonedible vegetable oil material, and renewable plasticizer. The main objective of this study is to investigate the effect of the incorporation of epoxidized jatropha oil (EJO) as a plasticizer and alkaline treatment of kenaf fiber on the thermal properties of PLA/Kenaf/EJO biocomposites. Kenaf fiber was treated with 6% sodium hydroxide (NaOH) solution for 4 h. The thermal properties of the biocomposites were analyzed using a differential scanning calorimetry (DSC) and thermogravimetric analysis (TGA). It must be highlighted that the addition of EJO resulted in a decrease of glass transition temperature which aided PLA chain mobility in the blend as predicted. TGA demonstrated that the presence of treated kenaf fiber together with EJO in the blends reduced the rate of decomposition of PLA and enhanced the thermal stability of the blend. The treatment showed a rougher surface fiber in scanning electron microscopy (SEM) micrographs and had a greater mechanical locking with matrix, and this was further supported with Fourier-transform infrared spectroscopy (FTIR) analysis. Overall, the increasing content of EJO as a plasticizer has improved the thermal properties of PLA/Kenaf/EJO biocomposites.
    Matched MeSH terms: Calorimetry, Differential Scanning
  13. Characterization of Microcrystalline Cellulose Isolated from Conocarpus Fiber
    Fouad H, Kian LK, Jawaid M, Alotaibi MD, Alothman OY, Hashem M
    Polymers (Basel), 2020 Dec 07;12(12).
    PMID: 33297332 DOI: 10.3390/polym12122926
    Conocarpus fiber is an abundantly available and sustainable cellulosic biomass. With its richness in cellulose content, it is potentially used for manufacturing microcrystalline cellulose (MCC), a cellulose derivative product with versatile industrial applications. In this work, different samples of bleached fiber (CPBLH), alkali-treated fiber (CPAKL), and acid-treated fiber (CPMCC) were produced from Conocarpus through integrated chemical process of bleaching, alkaline cooking, and acid hydrolysis, respectively. Characterizations of samples were carried out with Scanning Electron Microscope (SEM), Energy Dispersive X-ray (EDX), Fourier Transform Infrared-Ray (FTIR), X-ray Diffraction (XRD), Thermogravimetric (TGA), and Differential Scanning Calorimetry (DSC). From morphology study, the bundle fiber feature of CPBLH disintegrated into micro-size fibrils of CPMCC, showing the amorphous compounds were substantially removed through chemical depolymerization. Meanwhile, the elemental analysis also proved that the traces of impurities such as cations and anions were successfully eliminated from CPMCC. The CPMCC also gave a considerably high yield of 27%, which endowed it with great sustainability in acting as alternative biomass for MCC production. Physicochemical analysis revealed the existence of crystalline cellulose domain in CPMCC had contributed it 75.7% crystallinity. In thermal analysis, CPMCC had stable decomposition behavior comparing to CPBLH and CPAKL fibers. Therefore, Conocarpus fiber could be a promising candidate for extracting MCC with excellent properties in the future.
    Matched MeSH terms: Calorimetry, Differential Scanning
  14. Fulltext Microcapsules Filled with a Palm Oil-Based Alkyd as Healing Agent for Epoxy Matrix
    Shahabudin N, Yahya R, Gan SN
    Polymers (Basel), 2016 Apr 06;8(4).
    PMID: 30979216 DOI: 10.3390/polym8040125
    One of the approaches to prolong the service lifespan of polymeric material is the development of self-healing ability by means of embedded microcapsules containing a healing agent. In this work, poly(melamine-urea-formaldehyde) (PMUF) microcapsules containing a palm oil-based alkyd were produced by polymerization of melamine resin, urea and formaldehyde that encapsulated droplets of the suspended alkyd particles. A series of spherical and free-flowing microcapsules were obtained. The chemical properties of core and shell materials were characterized by Attenuated total reflection-Fourier transform infrared spectroscopy (ATR-FTIR) and proton nuclear magnetic resonance spectroscopy (¹H-NMR). Differential scanning calorimetry (DSC) analysis showed a glass transition around -15 °C due to the alkyd, and a melting temperature at around 200 °C due to the shell. Thermogravimetric analysis (TGA) results showed that the core and shell thermally degraded within the temperature range of 200⁻600 °C. Field emission scanning electron microscope (FESEM) examination of the ruptured microcapsule showed smooth inner and rough outer surfaces of the shell. Flexural strength and microhardness (Vickers) of the cured epoxy compound were not affected with the incorporation of 1%⁻3% of the microcapsules. The viability of the healing reactions was demonstrated by blending small amounts of alkyd with epoxy and hardener at different ratios. The blends could readily cure to non-sticky hard solids at room temperature and the reactions could be verified by ATR-FTIR.
    Matched MeSH terms: Calorimetry, Differential Scanning
  15. Fulltext Functional Hydrophilic Membrane for Oil-Water Separation Based on Modified Bio-Based Chitosan-Gelatin
    Zakuwan SZ, Ahmad I, Abu Tahrim N, Mohamed F
    Polymers (Basel), 2021 Apr 06;13(7).
    PMID: 33917600 DOI: 10.3390/polym13071176
    In this study, we fabricated a modified biomaterial based on chitosan and gelatin, which is an intrinsic hydrophilic membrane for oil-water separation to clean water contamination by oil. Modification of the membrane with a non-toxic natural crosslinker, genipin, significantly enhanced the stability of the biopolymer membrane in a water-based medium towards an eco-friendly environment. The effects of various compositions of genipin-crosslinked chitosan-gelatin membrane on the rheological properties, thermal stability, and morphological structure of the membrane were investigated using a dynamic rotational rheometer, thermogravimetry analysis, and chemical composition by attenuated total reflectance spectroscopy (ATR). Modified chitosan-gelatin membrane showed completely miscible blends, as determined by field-emission scanning electron microscopy, differential scanning calorimetry, and ATR. Morphological results showed membrane with establish microstructure to further experiment as filtration product. The membranes were successfully tested for their oil-water separation efficiencies. The membrane proved to be selective and effective in separating water from an oil-water mixture. The optimum results achieved a stable microporous structure of the membrane (microfiltration) and a separation efficiency of above 98%. The membrane showed a high permeation flux, generated as high as 698 and 420 L m-2 h-1 for cooking and crude oils, respectively. Owing to its outstanding recyclability and anti-fouling performance, the membrane can be washed away easily, ensuring the reusability of the prepared membrane.
    Matched MeSH terms: Calorimetry, Differential Scanning
  16. Fulltext Physicochemical Characterization, Molecular Docking, and In Vitro Dissolution of Glimepiride-Captisol Inclusion Complexes
    Pal A, Roy S, Kumar A, Mahmood S, Khodapanah N, Thomas S, et al.
    ACS Omega, 2020 Aug 18;5(32):19968-19977.
    PMID: 32832751 DOI: 10.1021/acsomega.0c01228
    This present study investigated the effect of Captisol, a chemically modified cyclodextrin, on the in vitro dissolution of glimepiride. We prepared glimepiride-Captisol complexes of different mass ratios (1:1, 1:2, and 1:3 w/w) by a physical mixing or freeze-drying technique, and found that complexation with Captisol enhanced the water solubility of glimepiride. Molecular docking and dynamic simulation predicted complex formation; at the same time, Fourier transform infrared spectroscopy, differential scanning calorimetry, powder X-ray diffractometry, and scanning electron microscope indicated molecular interactions that support complexation. We also found that an inclusion complex was better than a physical mixture in enhancing the complexation of glimepiride with Captisol and enhancing water solubility. Phase solubility study of the glimepiride-Captisol complex showed an AL-type profile, implying the formation of a 1:1 inclusion complex. The study also revealed that pH influenced the stability of the complex because the stability constant of the glimepiride-Captisol complex was higher in distilled water of pH ∼6.0 than in phosphate buffer of pH 7.2.
    Matched MeSH terms: Calorimetry, Differential Scanning
  17. Fulltext Functionality of Cellulose Nanofiber as Bio-Based Nucleating Agent and Nano-Reinforcement Material to Enhance Crystallization and Mechanical Properties of Polylactic Acid Nanocomposite
    Shazleen SS, Yasim-Anuar TAT, Ibrahim NA, Hassan MA, Ariffin H
    Polymers (Basel), 2021 Jan 27;13(3).
    PMID: 33513688 DOI: 10.3390/polym13030389
    Polylactic acid (PLA), a potential alternative material for single use plastics, generally portrays a slow crystallization rate during melt-processing. The use of a nanomaterial such as cellulose nanofibers (CNF) may affect the crystallization rate by acting as a nucleating agent. CNF at a certain wt.% has been evidenced as a good reinforcement material for PLA; nevertheless, there is a lack of information on the correlation between the amount of CNF in PLA that promotes its functionality as reinforcement material, and its effect on PLA nucleation for improving the crystallization rate. This work investigated the nucleation effect of PLA incorporated with CNF at different fiber loading (1-6 wt.%) through an isothermal and non-isothermal crystallization kinetics study using differential scanning calorimetry (DSC) analysis. Mechanical properties of the PLA/CNF nanocomposites were also investigated. PLA/CNF3 exhibited the highest crystallization onset temperature and enthalpy among all the PLA/CNF nanocomposites. PLA/CNF3 also had the highest crystallinity of 44.2% with an almost 95% increment compared to neat PLA. The highest crystallization rate of 0.716 min-1 was achieved when PLA/CNF3 was isothermally melt crystallized at 100 °C. The crystallization rate was 65-fold higher as compared to the neat PLA (0.011 min-1). At CNF content higher than 3 wt.%, the crystallization rate decreased, suggesting the occurrence of agglomeration at higher CNF loading as evidenced by the FESEM micrographs. In contrast to the tensile properties, the highest tensile strength and Young's modulus were recorded by PLA/CNF4 at 76.1 MPa and 3.3 GPa, respectively. These values were, however, not much different compared to PLA/CNF3 (74.1 MPa and 3.3 GPa), suggesting that CNF at 3 wt.% can be used to improve both the crystallization rate and the mechanical properties. Results obtained from this study revealed the dual function of CNF in PLA nanocomposite, namely as nucleating agent and reinforcement material. Being an organic and biodegradable material, CNF has an increased advantage for use in PLA as compared to non-biodegradable material and is foreseen to enhance the potential use of PLA in single use plastics applications.
    Matched MeSH terms: Calorimetry, Differential Scanning
  18. Fulltext PRELIMINARY STUDY OF 4-ARMS POLY(CAPROLACTONE) STAR- SHAPED POLYMER: SYNTHESIS AND CHARACTERIZATION
    Siti Hajar Ahmad Shariff, Mohamad Wafiuddin Ismail
    Journal of Academia Universiti Teknologi MARA Negeri Sembilan, 2021;9(1):127-138.
    MyJurnal
    Star-shaped polymers have vast potential in bioapplication due to their architecture. In this study, the suitability of ring opening polymerization (ROP) technique to synthesis star-shaped poly(caprolactone) and the thermal properties of the synthesized star-shaped polymers were demonstrated. The 4 -arm star- shaped of poly(caprolactone) (4s PCL) with -OH terminal and average molecular weight (Mn) of 5000, 10000, and 15000 g/mol were synthesized via ROP of ԑ-caprolactone (ԑ-CL) using a symmetric pentaerythritol (PET) as the core. Different molecular weights were obtained by using different ratios of ԑ-CL and PET in the presence of catalyst, stannous octoate (Sn(Oct)2). The FTIR spectra showed the presence of bands of methylene group of polymer repeating chain which confirm ROP of the ԑ- caprolactone. The average molecular weight (Mn) determined from proton nuclear magnetic resonance (1H NMR) analysis showed that all 4s PCL have approximately the same molecular weight as the theoretical values. All polymers obtained had high yield with >85%. Thermogravimetric analysis (TGA) and differential scanning calorimetry (DSC) analysis showed that there were no significance different in the thermal properties of the synthesized polymers. A single step degradation for all 4s PCL was observed and the crystallization melting point of the polymers was within the range of melting point of PCL.
    Matched MeSH terms: Calorimetry, Differential Scanning
  19. Effect of 1-Hexyl-3-Methylimidazolium Iodide Ionic Liquid on Ionic Conductivity and Energy Conversion Efficiency of Solid Polymer Electrolyte-Based Nano-Crystalline Dye-Sensitized Solar Cells
    Khanmirzaei MH, Ramesh S, Ramesh K
    J Nanosci Nanotechnol, 2020 Apr 01;20(4):2423-2429.
    PMID: 31492257 DOI: 10.1166/jnn.2020.17192
    Solid polymer electrolytes (SPEs) were prepared using rice starch as the polymer, sodium iodide (NaI) as the salt and 1-hexyl-3-methylimidazolium iodide (HMII) as the ionic liquid (IL). The solution casting technique was used for preparation of the PEs. The ionic conductivity and temperaturedependent properties of the PEs were measured and all the SPEs were found to follow the Arrhenius thermal activated model. Ionic conductivity increased as the percentage of ILs increased. The SPE containing 20% (wt) of HMII IL showed the highest ionic conductivity of 1.83×10-3 S/cm. Spectral and structural characterization of the PEs were performed by Fourier transform infrared spectroscopy (FTIR) and X-ray diffraction (XRD), respectively. The results of thermogravimetric analysis (TGA) and differential scanning calorimetry (DSC) indicate that the decomposition temperature (Tdc), glass transition temperatures (Tg) and melting points (Tm) shifted when complexation with HMII occurred. The PEs were used to fabricate dye-sensitized solar cells (DSSCs) and the DSSCs were analyzed under a 1-sun simulator. The SPE with the highest ionic conductivity displayed a short circuit current density (Jsc) of 9.07 (mA cm-2), open circuit voltage (Voc) of 0.58 (V), a fill factor (FF) of 0.65 and had the highest energy conversion efficiency of 3.42%.
    Matched MeSH terms: Calorimetry, Differential Scanning
  20. Fulltext Predictive Equations for the Estimation of Basal Metabolic Rate of Malaysian Adolescents
    Malays J Nutr, 1999;5(1):-.
    MyJurnal
    A longitudinal study was conducted to relate basal metabolic rate (BMR) with growth during adolescence. Subjects comprise 70 boys and 69 girls aged between ten and thirteen years at the time of recruitment. Parameters studied include anthropometric measurements and BMR, which was measured by indirect calorimetry using the Deltatrac metabolic monitor. Measurements were carried out serially once every six months, with a total of 713 BMR data points collected over three years. Mean BMR of boys aged 11, 12, 13 and 14 years were 4.96 ± 0.63 MJ/day, 5.28 ± 0.71 MJ/day, 5.73 ± 0.68 MJ/day and 5.92 ± 0.63 MJ/day, respectively; while mean BMR of girls in the 10, 11, 12 and 13 year age groups were 4.96 ± 0.63 MJ/day, 4.85 ± 0.63 MJ/day, 5.05 ± 0.55 MJ/day and 4.94 ± 0.51 MJ/day, respectively. Comparison of measured BMR with BMR values predicted from the FAO/WHO/UNU (1985) equations shows that the predictive equations overestimated the BMR of Malaysian boys by 3% and that of girls by 5%. The Henry & Rees (1991) equations for populations in the tropics underestimated BMR of boys and girls by 1% and 2%, respectively. Linear regression equations to predict BMR based on body weight were derived according to sex and age groups. It is recommended that these predictive equations be used for the estimation of BMR of Malaysian adolescents.
    Matched MeSH terms: Calorimetry, Indirect
Related Terms
Filters
Contact Us

Please provide feedback to Administrator (afdal@afpm.org.my)

External Links