MyMedR

Displaying publications 41 - 60 of 139 in total

Abstract:

Sort:

Effect of geometrical parameters on the performance of longitudinal functionally graded femoral prostheses

Oshkour AA, Talebi H, Seyed Shirazi SF, Yau YH, Tarlochan F, Abu Osman NA

Artif Organs, 2015 Feb;39(2):156-64.
PMID: 24841371 DOI: 10.1111/aor.12315

This study aimed to assess the performance of different longitudinal functionally graded femoral prostheses. This study was also designed to develop an appropriate prosthetic geometric design for longitudinal functionally graded materials. Three-dimensional models of the femur and prostheses were developed and analyzed. The elastic modulus of these prostheses in the sagittal plane was adjusted along a gradient direction from the distal end to the proximal end. Furthermore, these prostheses were composed of titanium alloy and hydroxyapatite. Results revealed that strain energy, interface stress, and developed stress in the femoral prosthesis and the bone were influenced by prosthetic geometry and gradient index. In all of the prostheses with different geometries, strain energy increased as gradient index increased. Interface stress and developed stress decreased. The minimum principal stress and the maximum principal stress of the bone slightly increased as gradient index increased. Hence, the combination of the femoral prosthetic geometry and functionally graded materials can be employed to decrease stress shielding. Such a combination can also be utilized to achieve equilibrium in terms of the stress applied on the implanted femur constituents; thus, the lifespan of total hip replacement can be prolonged.

Matched MeSH terms: Finite Element Analysis
Finite element analysis on longitudinal and radial functionally graded femoral prosthesis

Oshkour AA, Abu Osman NA, Davoodi MM, Yau YH, Tarlochan F, Wan Abas WA, et al.

Int J Numer Method Biomed Eng, 2013 Dec;29(12):1412-27.
PMID: 23922316 DOI: 10.1002/cnm.2583

This study focused on developing a 3D finite element model of functionally graded femoral prostheses to decrease stress shielding and to improve total hip replacement performance. The mechanical properties of the modeled functionally graded femoral prostheses were adjusted in the sagittal and transverse planes by changing the volume fraction gradient exponent. Prostheses with material changes in the sagittal and transverse planes were considered longitudinal and radial prostheses, respectively. The effects of cemented and noncemented implantation methods were also considered in this study. Strain energy and von Mises stresses were determined at the femoral proximal metaphysis and interfaces of the implanted femur components, respectively. Results demonstrated that the strain energy increased proportionally with increasing volume fraction gradient exponent, whereas the interface stresses decreased on the prostheses surfaces. A limited increase was also observed at the surfaces of the bone and cement. The periprosthetic femur with a noncemented prosthesis exhibited higher strain energy than with a cemented prosthesis. Radial prostheses implantation displayed more strain energy than longitudinal prostheses implantation in the femoral proximal part. Functionally graded materials also increased strain energy and exhibited promising potentials as substitutes of conventional materials to decrease stress shielding and to enhance total hip replacement lifespan.

Matched MeSH terms: Finite Element Analysis*
Design of new generation femoral prostheses using functionally graded materials: a finite element analysis

Oshkour AA, Abu Osman NA, Yau YH, Tarlochan F, Abas WA

Proc Inst Mech Eng H, 2013 Jan;227(1):3-17.
PMID: 23516951

This study aimed to develop a three-dimensional finite element model of a functionally graded femoral prosthesis. The model consisted of a femoral prosthesis created from functionally graded materials (FGMs), cement, and femur. The hip prosthesis was composed of FGMs made of titanium alloy, chrome-cobalt, and hydroxyapatite at volume fraction gradient exponents of 0, 1, and 5, respectively. The stress was measured on the femoral prosthesis, cement, and femur. Stress on the neck of the femoral prosthesis was not sensitive to the properties of the constituent material. However, stress on the stem and cement decreased proportionally as the volume fraction gradient exponent of the FGM increased. Meanwhile, stress became uniform on the cement mantle layer. In addition, stress on the femur in the proximal part increased and a high surface area of the femoral part was involved in absorbing the stress. As such, the stress-shielding area decreased. The results obtained in this study are significant in the design and longevity of new prosthetic devices because FGMs offer the potential to achieve stress distribution that more closely resembles that of the natural bone in the femur.

Matched MeSH terms: Finite Element Analysis
Hartmann and Reynolds numbers effects in the newtonian blood flow of a bifurcated artery with an overlapping stenosis

Norliza Mohd. Zain, Zuhaila Ismail

MATEMATIKA, 2019;35(2):213-227.
MyJurnal

Blood flow through a bifurcated artery with the presence of an overlapping stenosis located at parent’s arterial lumen under the action of a uniform external magnetic field is studied in this paper. Blood is treated as an electrically conducting fluid which exhibits the Magnetohydrodynamics principle and it is characterized by a Newtonian fluid model. The governing equations are discretized using a stabilization technique of finite element known as Galerkin least-squares. The maximum velocity and pressure drop evaluated in this present study are compared with the results found in previous literature and COMSOL Multiphysics. The solutions found in a satisfactory agreement, thus verify the source code is working properly. The effects of dimensionless parameters of Hartmann and Reynolds numbers in the fluid’s velocity and pressure are examined in details with further scientific discussions.

Matched MeSH terms: Finite Element Analysis
Fulltext Finite element simulation of takraw balls and their impact on a flat surface

Norhafizan Ahmad, Zahari Taha, Tuan Mohammad Yusoff Shah Tuan Ya, Iskandar Hasanuddin

Movement Health & Exercise, 2012;1(1):1-9.
MyJurnal

The takraw ball is a very unique interwoven ball used in the action game of sepak takraw. The traditional takraw ball is manufactured by conventionally weaving split rattan strips into a spherical basket. Modern takraw balls are manufactured by forming strips of plastics materials into interwoven hoop. These interwoven hoops form 12 pentagon holes and 30 intersections. The purpose of this study is to construct a finite-element (FE) model of a takraw ball in particular for normal impact simulation on flat surfaces under low speed conditions. Two FE models were developed to observe the dynamic behavior including impact forces, contact time, coefficient of restitution and deformation of the ball. The first model consists of a single solid hollow ball with 12 pentagon holes and the second model consists of six center strips and 12 side edge strips of
extrusion hoops to form 12 pentagon holes and 270 cross-sections. The models were also compared with results of experimental impact tests whereby the ball was impacted normal to a rigid plate at three different heights. The ball is described in the FE model as a linear elastic material.
It was found that the FE analysis solution of the ball model was found to be reasonably close with the experimental results. However further improvement need to be done by taking into consideration the nonlinearity of the takraw ball under large deformation as well as at high impact velocity.

Matched MeSH terms: Finite Element Analysis
Fulltext A Finite Element Model for Dynamic Analysis of Triple-Layer Composite Plates with Layers Connected by Shear Connectors Subjected to Moving Load

Nguyen HN, Nguyen TY, Tran KV, Tran TT, Nguyen TT, Phan VD, et al.

Materials (Basel), 2019 Feb 16;12(4).
PMID: 30781542 DOI: 10.3390/ma12040598

Triple-layered composite plates are created by joining three composite layers using shear connectors. These layers, which are assumed to be always in contact and able to move relatively to each other during deformation, could be the same or different in geometric dimensions and material. They are applied in various engineering fields such as ship-building, aircraft wing manufacturing, etc. However, there are only a few publications regarding the calculation of this kind of plate. This paper proposes novel equations, which utilize Mindlin's theory and finite element modelling to simulate the forced vibration of triple-layered composite plates with layers connected by shear connectors subjected to a moving load. Moreover, a Matlab computation program is introduced to verify the reliability of the proposed equations, as well as the influence of some parameters, such as boundary conditions, the rigidity of the shear connector, thickness-to-length ratio, and the moving load velocity on the dynamic response of the composite plate.

Matched MeSH terms: Finite Element Analysis
Assessment of compressive failure process of cortical bone materials using damage-based model

Ng TP, R Koloor SS, Djuansjah JRP, Abdul Kadir MR

J Mech Behav Biomed Mater, 2017 02;66:1-11.
PMID: 27825047 DOI: 10.1016/j.jmbbm.2016.10.014

The main failure factors of cortical bone are aging or osteoporosis, accident and high energy trauma or physiological activities. However, the mechanism of damage evolution coupled with yield criterion is considered as one of the unclear subjects in failure analysis of cortical bone materials. Therefore, this study attempts to assess the structural response and progressive failure process of cortical bone using a brittle damaged plasticity model. For this reason, several compressive tests are performed on cortical bone specimens made of bovine femur, in order to obtain the structural response and mechanical properties of the material. Complementary finite element (FE) model of the sample and test is prepared to simulate the elastic-to-damage behavior of the cortical bone using the brittle damaged plasticity model. The FE model is validated in a comparative method using the predicted and measured structural response as load-compressive displacement through simulation and experiment. FE results indicated that the compressive damage initiated and propagated at central region where maximum equivalent plastic strain is computed, which coincided with the degradation of structural compressive stiffness followed by a vast amount of strain energy dissipation. The parameter of compressive damage rate, which is a function dependent on damage parameter and the plastic strain is examined for different rates. Results show that considering a similar rate to the initial slope of the damage parameter in the experiment would give a better sense for prediction of compressive failure.

Matched MeSH terms: Finite Element Analysis
Fulltext Numerical Prediction of Residual Stresses Distribution in Thin-Walled Press-Braked Stainless Steel Sections

Mutafi A, Yidris N, Koloor SSR, Petrů M

Materials (Basel), 2020 Nov 26;13(23).
PMID: 33256257 DOI: 10.3390/ma13235378

Stainless steels are increasingly used in construction today, especially in harsh environments, in which steel corrosion commonly occurs. Cold-formed stainless steel structures are currently increasing in popularity because of its efficiency in load-bearing capacity and its appealing architectural appearance. Cold-rolling and press-braking are the cold-working processes used in the forming of stainless steel sections. Press braking can produce large cross-sections from thin to thick-walled sections compared to cold-rolling. Cold-forming in press-braked sections significantly affect member behaviour and joints; therefore, they have attained great attention from many researchers to initiate investigations on those effects. This paper examines the behaviour of residual stress distribution of stainless steel press-braked sections by implementing three-dimensional finite element (3D-FE) technique. The study proposed a full finite element procedure to predict the residual stresses starting from coiling-uncoiling to press-braking. This work considered material anisotropy to examine its effect on the residual stress distribution. The technique adopted was compared with different finite element techniques in the literature. This study also provided a parametric study for three corner radius-to-thickness ratios looking at the through-thickness residual stress distribution of four stainless steels (i.e., ferritic, austenitic, duplex, lean duplex) in which have their own chemical composition. In conclusion, the comparison showed that the adopted technique provides a detailed prediction of residual stress distribution. The influence of geometrical aspects is more pronounced than the material properties. Neglecting the material anisotropy shows higher shifting in the neutral axis. The parametric study showed that all stainless steel types have the same stress through-thickness distribution. Moreover, R/t ratios' effect is insignificant in all transverse residual stress distributions, but a slight change to R/t ratios can affect the longitudinal residual stress distribution.

Matched MeSH terms: Finite Element Analysis
Fulltext An investigation on longitudinal residual strains distribution of thin-walled press-braked cold formed steel sections using 3D FEM technique

Mutafi A, Yidris N, Ishak MR, Zahari R

Heliyon, 2018 Nov;4(11):e00937.
PMID: 30839801 DOI: 10.1016/j.heliyon.2018.e00937

Steel sections are normally shaped via cold work manufacturing processes. The extent of cold work to shape the steel sections might induce residual stresses in the region of bending. Previously, researchers had performed studies on the influences of local buckling on the failure behavior of steel compression members which shown that failure will happen when most of the yielding has extended to the middle surface in the bend region of the sections. Therefore, these cold work methods may have major effect on the behavior of the steel section and also its load-bearing capability. In addition, another factor may play significant role in formed section's load-bearing capacity which is the longitudinal residual strain. The longitudinal residual strain raised during forming procedure can be used to define the section imperfection of the formed section and its relation to the existence of defects. Therefore, the main motivation of this research paper is to perform three-dimensional finite element (3D-FE) to investigate peak longitudinal residual strains of a thin-walled steel plate with large bending angle along member length. A 3D finite element simulation in ABAQUS has been employed to simulate this forming process. The study concluded that the longitudinal residual strain at the section corner edge was higher than those at the rest of the corner region. These strains at the edge were higher than the yield strain

(

ε

y

)

of the formed section which occurred due to the lack of transverse restraint. This made the plate edge tended to bend toward the normal direction when it was under a high transverse bending. This causes a significant difference in longitudinal strain at the plate edge.

Matched MeSH terms: Finite Element Analysis
The influence of experimental silane primers on dentin bond strength and morphology: a laboratory and finite element analysis study

Mustafa AA, Matinlinna JP, Saidin S, Kadir MR

J Prosthet Dent, 2014 Dec;112(6):1498-506.
PMID: 24993375 DOI: 10.1016/j.prosdent.2014.05.011

STATEMENT OF PROBLEM: The inconsistency of dentin bonding affects retention and microleakage.
PURPOSE: The purpose of this laboratory and finite element analysis study was to investigate the effects on the formation of a hybrid layer of an experimental silane coupling agent containing primer solutions composed of different percentages of hydroxyethyl methacrylate.
MATERIAL AND METHODS: A total of 125 sound human premolars were restored in vitro. Simple class I cavities were formed on each tooth, followed by the application of different compositions of experimental silane primers (0%, 5%, 25%, and 50% of hydroxyethyl methacrylate), bonding agents, and dental composite resins. Bond strength tests and scanning electron microscopy analyses were performed. The laboratory experimental results were validated with finite element analysis to determine the pattern of stress distribution. Simulations were conducted by placing the restorative composite resin in a premolar tooth by imitating simple class I cavities. The laboratory and finite element analysis data were significantly different from each other, as determined by 1-way ANOVA. A post hoc analysis was conducted on the bond strength data to further clarify the effects of silane primers.
RESULTS: The strongest bond of hybrid layer (16.96 MPa) was found in the primer with 25% hydroxyethyl methacrylate, suggesting a barely visible hybrid layer barrier. The control specimens without the application of the primer and the primer specimens with no hydroxyethyl methacrylate exhibited the lowest strength values (8.30 MPa and 11.78 MPa) with intermittent and low visibility of the hybrid layer. These results were supported by finite element analysis that suggested an evenly distributed stress on the model with 25% hydroxyethyl methacrylate.
CONCLUSIONS: Different compositions of experimental silane primers affected the formation of the hybrid layer and its resulting bond strength.

Matched MeSH terms: Finite Element Analysis
Fulltext Finite element modelling and simulation for lower limb of human bone: a review

Muhammad Hanif Ramlee

Malaysian Journal of Medicine and Health Sciences, 2020;16(3):262-271.
MyJurnal

Most orthopaedic cases that involved with bone fracture are normally treated with medical implants. To be noticed that some precautions in terms of biomechanical and biomaterial properties are necessary for a successful post-sur- gery process. The biomechanical evaluation of implants could be carried out using computing and engineering technologies. However, in the computer simulation, some assumptions are needed as the limitations on computer resources and data input. This review focuses on the current method of developing the finite element model for patients with specific values of material properties for lower limb part such as hip, knee and ankle joint. Previous literature was reviewed from which keywords and search engines were identified. In this review, inclusion and exclusion criteria were used to limit the literature search. We reviewed the state-of-the-art in this area and provide recommendations for future research. In conclusion, the previous published reports illustrated different methods to develop numerical models.

Matched MeSH terms: Finite Element Analysis
Fulltext Biomechanical Stress in Obturator Prostheses: A Systematic Review of Finite Element Studies

Mousa MA, Abdullah JY, Jamayet NB, Alam MK, Husein A

Biomed Res Int, 2021;2021:6419774.
PMID: 34447852 DOI: 10.1155/2021/6419774

Aim: This systematic review is aimed at investigating the biomechanical stress that develops in the maxillofacial prostheses (MFP) and supporting structures and methods to optimize it. Design and Methods. A literature survey was conducted for full-text English articles which used FEA to examine the stress developed in conventional and implant-assisted MFPs from January 2010 to December 2020.
Results: 87 articles were screened to get an update on the desired information. 74 were excluded based on a complete screening, and finally, 13 articles were recruited for complete reviewing. Discussion. The MFP is subjected to stress, which is reflected in the form of compressive and tensile strengths. The stress is mainly concentrated the resection line and around the apices of roots of teeth next to the defect. Diversity of designs and techniques were introduced to optimize the stress distribution, such as modification of the clasp design, using materials with different mechanical properties for dentures base and retainer, use of dental (DI) and/or zygomatic implants (ZI), and free flap reconstruction before prosthetic rehabilitation.
Conclusion: Using ZI in the defective side of the dentulous maxillary defect and defective and nondefective side of the edentulous maxillary defect was found more advantageous, in terms of compression and tensile stress and retention, when compared with DI and free flap reconstruction.

Matched MeSH terms: Finite Element Analysis
Extracellular matrix integrity affects the mechanical behaviour of in-situ chondrocytes under compression

Moo EK, Han SK, Federico S, Sibole SC, Jinha A, Abu Osman NA, et al.

J Biomech, 2014 Mar 21;47(5):1004-13.
PMID: 24480705 DOI: 10.1016/j.jbiomech.2014.01.003

Cartilage lesions change the microenvironment of cells and may accelerate cartilage degradation through catabolic responses from chondrocytes. In this study, we investigated the effects of structural integrity of the extracellular matrix (ECM) on chondrocytes by comparing the mechanics of cells surrounded by an intact ECM with cells close to a cartilage lesion using experimental and numerical methods. Experimentally, 15% nominal compression was applied to bovine cartilage tissues using a light-transmissible compression system. Target cells in the intact ECM and near lesions were imaged by dual-photon microscopy. Changes in cell morphology (N(cell)=32 for both ECM conditions) were quantified. A two-scale (tissue level and cell level) Finite Element (FE) model was also developed. A 15% nominal compression was applied to a non-linear, biphasic tissue model with the corresponding cell level models studied at different radial locations from the centre of the sample in the transient phase and at steady state. We studied the Green-Lagrange strains in the tissue and cells. Experimental and theoretical results indicated that cells near lesions deform less axially than chondrocytes in the intact ECM at steady state. However, cells near lesions experienced large tensile strains in the principal height direction, which are likely associated with non-uniform tissue radial bulging. Previous experiments showed that tensile strains of high magnitude cause an up-regulation of digestive enzyme gene expressions. Therefore, we propose that cartilage degradation near tissue lesions may be due to the large tensile strains in the principal height direction applied to cells, thus leading to an up-regulation of catabolic factors.

Matched MeSH terms: Finite Element Analysis
Mechanical behaviour of in-situ chondrocytes subjected to different loading rates: a finite element study

Moo EK, Herzog W, Han SK, Abu Osman NA, Pingguan-Murphy B, Federico S

Biomech Model Mechanobiol, 2012 Sep;11(7):983-93.
PMID: 22234779 DOI: 10.1007/s10237-011-0367-2

Experimental findings indicate that in-situ chondrocytes die readily following impact loading, but remain essentially unaffected at low (non-impact) strain rates. This study was aimed at identifying possible causes for cell death in impact loading by quantifying chondrocyte mechanics when cartilage was subjected to a 5% nominal tissue strain at different strain rates. Multi-scale modelling techniques were used to simulate cartilage tissue and the corresponding chondrocytes residing in the tissue. Chondrocytes were modelled by accounting for the cell membrane, pericellular matrix and pericellular capsule. The results suggest that cell deformations, cell fluid pressures and fluid flow velocity through cells are highest at the highest (impact) strain rate, but they do not reach damaging levels. Tangential strain rates of the cell membrane were highest at the highest strain rate and were observed primarily in superficial tissue cells. Since cell death following impact loading occurs primarily in superficial zone cells, we speculate that cell death in impact loading is caused by the high tangential strain rates in the membrane of superficial zone cells causing membrane rupture and loss of cell content and integrity.

Matched MeSH terms: Finite Element Analysis
Interface pressure profile analysis for patellar tendon-bearing socket and hydrostatic socket

Moo EK, Osman NA, Pingguan-Murphy B, Abas WA, Spence WD, Solomonidis SE

Acta Bioeng Biomech, 2009;11(4):37-43.
PMID: 20405814

Conventionally, patellar tendon-bearing (PTB) sockets, which need high dexterity of prosthetist, are widely used. Lack of chartered and experienced prosthetist has often led to painful experience of wearing prosthesis and this will in turn deter the patients to wear the prosthesis, which will further aggravate stump shrinkage. Thus, the hydrostatic socket which demands relatively lower level of fabricating skill is proposed to replace the PTB socket in order to produce the equivalent, if not better, quality of support to the amputee patients. Both sockets' pressure profiles are studied and compared using finite element analysis (FEA) software. Three-dimensional models of both sockets were developed using MIMICS software. The analysis results showed that hydrostatic socket did exhibit more uniform pressure profiles than that of PTB socket. PTB socket showed pressure concentration near the proximal brim of the socket and also at the distal fibula. It was also found that the pressure magnitude in hydrostatic socket is relatively lower than that of PTB socket.

Matched MeSH terms: Finite Element Analysis
Fulltext A Theoretical Study of Surface Mode Propagation with a Guiding Layer of GaN/Sapphire Hetero-Structure in Liquid Medium

Mohd Razip Wee MF, Jaafar MM, Faiz MS, Dee CF, Yeop Majlis B

Biosensors (Basel), 2018 Dec 05;8(4).
PMID: 30563159 DOI: 10.3390/bios8040124

Gallium Nitride (GaN) is considered as the second most popular semiconductor material in industry after silicon. This is due to its wide applications encompassing Light Emitting Diode (LED) and power electronics. In addition, its piezoelectric properties are fascinating to be explored as electromechanical material for the development of diverse microelectromechanical systems (MEMS) application. In this article, we conducted a theoretical study concerning surface mode propagation, especially Rayleigh and Sezawa mode in the layered GaN/sapphire structure with the presence of various guiding layers. It is demonstrated that the increase in thickness of guiding layer will decrease the phase velocities of surface mode depending on the material properties of the layer. In addition, the Q-factor value indicating the resonance properties of surface mode appeared to be affected with the presence of fluid domain, particularly in the Rayleigh mode. Meanwhile, the peak for Sezawa mode shows the highest Q factor and is not altered by the presence of fluid. Based on these theoretical results using the finite element method, it could contribute to the development of a GaN-based device to generate surface acoustic wave, especially in Sezawa mode which could be useful in acoustophoresis, lab on-chip and microfluidics applications.

Matched MeSH terms: Finite Element Analysis
Fulltext Simulating bio-composite cycling helmet performance through FEA and CFD approaches

Mohd Naim Abdullah, Mustapha, F., Muda, M.K.H., Arrifin, M.K.A., Rafie, A.S.M., Shamsudin, M.A.

Movement Health & Exercise, 2015;4(1):77-91.
MyJurnal

Finite Element Analysis (FEA) and Computational Fluid Dynamics (CFD) analysis were performed in this work in order to obtain the best design for safety and aerodynamic performance of the bicycle cycling helmet. FEA analysis was computed on two different helmet designs to determine the critical area subjected to impact. A pressure load was applied on the helmets’ outer surface to simulate oblique loading. The critical areas of the helmets were then highlighted and identified, enabling design improvements to be made on both designs. CFD analysis was then executed in order to obtain the lowest drag coefficient number in reducing the air resistance induced by both of the helmet designs, inherently increasing cyclist performance and ensuring competition success.

Matched MeSH terms: Finite Element Analysis
Fulltext Investigation into mass loading sensitivity of sezawa wave mode-based surface acoustic wave sensors

Mohanan AA, Islam MS, Ali SH, Parthiban R, Ramakrishnan N

Sensors (Basel), 2013;13(2):2164-75.
PMID: 23389346 DOI: 10.3390/s130202164

In this work mass loading sensitivity of a Sezawa wave mode based surface acoustic wave (SAW) device is investigated through finite element method (FEM) simulation and the prospects of these devices to function as highly sensitive SAW sensors is reported. A ZnO/Si layered SAW resonator is considered for the simulation study. Initially the occurrence of Sezawa wave mode and displacement amplitude of the Rayleigh and Sezawa wave mode is studied for lower ZnO film thickness. Further, a thin film made of an arbitrary material is coated over the ZnO surface and the resonance frequency shift caused by mass loading of the film is estimated. It was observed that Sezawa wave mode shows significant sensitivity to change in mass loading and has higher sensitivity (eight times higher) than Rayleigh wave mode for the same device configuration. Further, the mass loading sensitivity was observed to be greater for a low ZnO film thickness to wavelength ratio. Accordingly, highly sensitive SAW sensors can be developed by coating a sensing medium over a layered SAW device and operating at Sezawa mode resonance frequency. The sensitivity can be increased by tuning the ZnO film thickness to wavelength ratio.

Matched MeSH terms: Finite Element Analysis
Fulltext Optimization of interlocking structures made of flax fibre composites to improve its energy absorption capability

Mohamed Ibrahim J. Ibrahim, Mohd Zuhri Mohamed Yusoff

Journal of Advanced Research in Applied Sciences and Engineering Technology, 2018;10(1):1-17.
MyJurnal

This study presents an investigation about the effect of size variation on mechanical
performance of square core interlocking structures, by using finite element analysis
(FEA). The material used in this study is flax fibre reinforced polypropylene (PP)
composite. Abaqus software was used for modelling and visualizing number of six
interlocking honeycomb structures with different cell sizes and heights. In the first
analysis, Abaqus/standard was performed on the perfect models by applying quasistatic
loading to identify the imperfection shape and obtaining the buckling Eigenmodes
for the models, then the Eigen-modes from abaqus/standard were imported
to abaqus/explicit to run post-buckling analysis and simulate the overall imperfection
behaviour of models. The numerical results from the finite element analysis
simulation were used to plot load-displacement curve to each model. The area under
the load-displacement curve represents the total absorbed energy, energy absorption
per unit mass indicates the specific energy absorption, and the highest value of
specific energy absorption represents the optimum size. The findings demonstrated
that the square interlocking structure exhibits good energy absorption performance
in some geometrical cases, and also revealed that the natural fibre composites have
unique energy absorption capability under quasi-static loads.

Matched MeSH terms: Finite Element Analysis
Fulltext A three-dimension finite element analysis to evaluate the stress distribution in tooth supported 5-unit intermediate abutment prosthesis with rigid and nonrigid connector

Modi R, Kohli S, Rajeshwari K, Bhatia S

Eur J Dent, 2015 6 4;9(2):255-261.
PMID: 26038660 DOI: 10.4103/1305-7456.156847

OBJECTIVE: The aim of the study is to evaluate the stress distribution in tooth supported 5-unit fixed partial denture (FPD) having tooth as pier abutment using rigid and nonrigid connectors respectively, under simultaneous and progressive loading.
MATERIAL AND METHODS: The three-dimensional (3D) finite element program (ANSYS software) was used to construct the mathematical model. Two 5-unit FPD'S were simulated, one with rigid connector and another one with nonrigid connector. For analysis, each of these models were subjected to axial and oblique forces under progressive loading (180, 180, 120, 120, 80 N force on first and second molars, premolars and canine respectively) and simultaneous loading (100, 100, 100, 100, 100 N force on first and second molars, premolars and canine respectively).
RESULTS: The rigid and nonrigid connector design have effect on stress distribution in 5-unit FPDs with pier abutments.
CONCLUSION: Oblique forces produce more stresses than vertical forces. Nonrigid connector resulted in decrease in stress at the level of prosthesis and increase in stress at the level of alveolar crest.

Matched MeSH terms: Finite Element Analysis

Filters

Please provide feedback to Administrator (afdal@afpm.org.my)

External Links