Studies on toxicities and tolerances of cadmium (Cd), copper (Cu), lead (Pb) and zinc (Zn) in the brown alga Isochrysis galbana and in the green-lipped mussel Perna viridis were conducted by short-term bioassays using endpoints growth production and mortality, respectively. The 5-day EC(50) and 24-h LC(50) of these heavy metals were determined in the brown alga and mussel, respectively. The EC(50) values calculated for the alga were 0.74 mg/l for Cd, 0.91 mg/l for Cu, 1.40 mg/l for Pb and 0.60 mg/l for Zn. The LC(50) values for the mussels were 1.53 mg/l for Cd, 0.25 mg/l for Cu, 4.12 mg/l for Pb and 3.20 mg/l for Zn. These LC(50) values were within the concentration ranges as reported by other authors who used P. viridis as the test organism. Based on these EC(50) and LC(50) values, the alga was most sensitive to Zn, followed by Cd, Cu and Pb while the mussel was most sensitive to Cu, followed by Cd, Zn and Pb. Differences in the trophic levels, metal handling strategies, biology and ecology of the primary producer (brown alga) and the primary consumer (mussel) are believed to be the plausible causes for the different toxicities and tolerances of the metals studied.
It has been widely reported that heavy metal contamination in coastal waters can modify the allozyme profiles of marine organisms. Previous studies have recorded elevated metal concentrations in sediments and mussel tissues off Peninsular Malaysia. In the present study, horizontal starch gel electrophoresis was carried out to estimate the levels of allelic variation of the green-lipped mussel, Perna viridis, collected from one contaminated and three relatively uncontaminated sites off Peninsular Malaysia. Fourteen polymorphic loci were observed. In addition, the concentrations of cadmium, copper, lead, mercury and zinc were determined in the sediments and in the soft tissues of the mussels. Mussels from contaminated site, evidenced by high metal pollution indices (MPI) of the sediment and the mussel tissues, showed the highest percentage of polymorphic loci (78.6%), while those collected from the uncontaminated sites had lower MPI of the sediment and mussel tissue, and exhibited lower percentages of polymorphic loci (35.7-57.1%). The population from the contaminated site showed the highest excess of heterozygosity (0.289) when compared to that of the populations from the three uncontaminated sites (0.108-0.149). Allozyme frequencies at the phosphoglucomutase (PGM; E.C. 2.7.5.1) locus also differed between the contaminated and uncontaminated populations. Previous studies have shown that exposure to heavy metals can select or counter-select for particular alleles at this locus. The present results suggest that allozyme polymorphism in P. viridis is a potential biomonitoring tool for heavy metal contamination but further validation is required.
Total concentrations and speciation of cadmium (Cd), copper (Cu), lead (Pb) and zinc (Zn) in surface sediment samples were correlated with the respective metal measured in the total soft tissue of the green-lipped mussel Perna viridis, collected from water off the west coast of Peninsular Malaysia. The aim of this study is to relate the possible differences in the accumulation patterns of the heavy metals in P. viridis to those in the surface sediment. The sequential extraction technique was employed to fractionate the sediment into 'freely leachable and exchangeable' (EFLE), 'acid-reducible,' 'oxidisable-organic' and 'resistant' fractions. The results showed that significant (P .05) was found between Zn in P viridis and all the sediment geochemical fractions of Zn and total Zn in the sediment. This indicated that Zn was possibly regulated from the soft tissue of P. viridis. The present results supported the use of P viridis as a suitable biomonitoring agent for Cd, Cu and Pb.
Centella asiatica is widely used as a medicinal plant in Malaysia and other parts of the world. In the present study, the growth and uptake of heavy metal by C. asiatica were determined based on the plant exposure to different treatment of metal-contaminated soils under laboratory conditions. Heavy metals uptake in different parts of the plants namely roots, stems and leaves were determined. In general, it was found that the metal uptake capacity followed the order: roots > stems > leaves. Since a close positive relationship was established between the concentrations of metal accumulated in different parts of the plant and the metal levels in the most contaminated soil, C. asiatica has the potential of being used as a biomonitoring plant for heavy metal pollution in the polluted soils.
In this study, heavy metal data (including four geochemical fractions) from offshore and intertidal sediments collected off the west coast of Peninsular Malaysia were analyzed using factor analysis. A similarity was found when comparing between offshore and intertidal sediments, where out of the 20 variables, five factors (resistant Cu, total Cu, resistant Pb, total Pb and total Zn) could be clearly selected on the basis of their high loadings as derived by factor analysis in both sediment sampling areas. However, the statistical outputs based on the present study using factor analysis cannot be practically acceptable mainly because the resistant fractions are not of anthropogenic origins and ecotoxicologists are more concern on the anthropogenic ones. Only a modification using a specific normalizing agent such as the nonresistant fraction, should be tested to show feasibility of the contribution of anthropogenic sources in the two sampling areas. However, a more comprehensive metal monitoring data should be compiled to complement the results obtainable from factor analysis, before a valid Malaysian Marine Sediment Pollution Index or Sediment Quality Guidelines, can be proposed to be established.
The periostracum is the outermost layer overlying the inner prismatic and nacreous layers of the shells of bivalves. In the present study, the distributions of Cd and Pb in the soft tissues (ST) and periostracum of the green-lipped mussel Perna viridis sampled from 15 sampling sites in the coastal waters of Peninsular Malaysia were determined. The concentrations of Cd (0.21-10.87 mg/g dry weight) and Pb (1.16-40.20 mg/g dry weight) in the periostracum were generally higher than those in the ST (Cd: 0.10-5.55 mg/g dry weight; Pb: 2.53-18.62 mg/g dry weight). Based on correlation analysis from nine geographical populations, the higher correlation coefficients (R values) between the periostracum-geochemical fractions of the sediments than between the ST-geochemical fractions of the sediments indicated that the periostracum could be a potential biomonitoring material for Pb. Hence, the present results supported the use of the periostracum of P. viridis as a potential biomonitoring material for Pb but not for Cd. However, more studies are warranted to verify its usefulness for the biomonitoring of heavy metal pollution in tropical coastal waters.
This study compared some allometric parameters (shell length, shell width, shell height, total dry weight of soft tissues, condition index and heavy metals (Cd, Cu, Pb and Zn) in the different soft tissues of Perna viridis collected from Sebatu and Muar estuary. It was found that the total dry weight of soft tissues and condition index of mussels collected from Sebatu were significantly (p<0.05) higher than those in Muar. The significantly (p<0.05) higher concentrations of Cu in most soft tissues and some of Cd indicated a higher bioavailability of Cu and Cd at Muar than Sebatu. In addition, the significantly (p<0.05) higher levels of Cu, Cd, Zn and Pb in surface sediments collected from Muar supported the observable anthropogenic impacts at Muar than Sebatu and hence, higher metal contamination at Muar than Sebatu. The higher condition index value in mussels recorded in Sebatu than in Muar was believed to be a result of higher metal contamination at Muar estuary.
Resin-bonded fibre-reinforced composite bridges provide many advantages over the conventional
bridges or implant treatment in the management of a traumatically or congenitally missing anterior tooth.
Furthermore, there is an increasing demand towards providing a metal free resin-bonded bridges over the alloybased
restorations in order to meet the aesthetic needs especially in the anterior region. Advances in the
adhesive technology and tooth colored materials offer improved bonding system and better aesthetic outcome.
Nevertheless, careful selection of cases to receive this type of approach is also one of the key factor to ensure
the clinical survival of fibre-reinforced composite bridges. This report aims to present the use of fibre-reinforced
composite to construct indirect cantilever fibre-reinforced composite bridges as part of minimum intervention
dentistry.
The presence of both heavy metals and organic xenobiotic pollutants in a contaminated site
justifies the application of either a multitude of microbial degraders or microorganisms having
the capacity to detoxify a number of pollutants at the same time. Molybdenum is an essential
heavy metal that is toxic to ruminants at a high level. Ruminants such as cow and goats
experience severe hypocuprosis leading to scouring and death at a concentration as low as
several parts per million. In this study, a molybdenum-reducing bacterium with amide-degrading
capacity has been isolated from contaminated soils. The bacterium, using glucose as the best
electron donor reduces molybdenum in the form of sodium molybdate to molybdenum blue. The
maximal pH reduction occurs between 6.0 and 6.3, and the bacterium showed an excellent
reduction in temperatures between 25 and 40 oC. The reduction was maximal at molybdate
concentrations of between 15 and 25 mM. Molybdenum reduction incidentally was inhibited by
several toxic heavy metals. Other carbon sources including toxic xenobiotics such as amides
were screened for their ability to support molybdate reduction. Of all the amides, only
acrylamide can support molybdenum reduction. The other amides; such as acetamide and
propionamide can support growth. Analysis using phylogenetic analysis resulted in a tentative
identification of the bacterium as Pseudomonas sp. strain 135. This bacterium is essential in
remediating sites contaminated with molybdenum, especially in agricultural soil co-contaminated
with acrylamide, a known soil stabilizer.
The distribution of heavy metals (Cu, Zn, Cd, Pb) in surface sediments was examined in waters off the coast of Marang, Terengganu. A total of 20 samples were collected using Ponar grab and analysed by inductively coupled plasma-mass spectrometer after closed digestion with acid. The sediments were filtered using a dry sieving method to determine their particle size. The spatial distribution maps on the concentration of selected metals were drawn using the ArcGIS software. Results showed that the average concentration of Cu, Zn, Cd, and Pb were 2.33±0.38 µg/g dry weight, 28.4±3.78 µg/g dry weight, 0.09±0.01 µg/g dry weight and 8.35±1.48 µg/g dry weight, respectively. The level of pollution was also evaluated using the Index of Geoaccumulation (Igeo) and Pollution Load Index (PLI). All Igeo and PLI values obtained were low, which indicated low or no pollution. Meanwhile, the sediment mean size ranged between -0.77Ø and 3.18Ø, which characterised a sandy type of sediment. Correlation analysis showed a positive correlation between the heavy metals and sediment size. The results indicated that there was a common source of heavy metal pollution in the study area, possibly from shipping activities. Overall, there was no significant heavy metal pollution in the waters off Marang. This finding is important as the data could be used to evaluate the risk of metal contamination and the impact of anthropogenic activities on the marine environment.
The effect of corrosion inhibition of low carbon steel in water based medium containing lignin was investigated via weight loss method. The evolution of surface morphology has been carried out for 7 to 42 days via optical microscopy (OM), scanning electron microscopy (SEM), energy-dispersive X-ray spectroscopy (EDX) and X-ray photoelectron microscopy (XPS). Immersion of metal specimen without lignin shows that significant increase in the surface roughness. The longer the immersion time, the more the oxide crust formed. The surface degradation of metal specimen was well protected by immersion in lignin solution. A protective layer containing of lignin was formed on the surface of metal specimens after 7 and 21 days immersion. The corrosion inhibition gives about 13 and 53% inhibition for both 7 and 21 days immersion, respectively. The protective layers were spalling and separated from the metal surface after 42 days immersion in lignin solution possibly due to the increase in corrosion attack after long time immersion according to the increase in dissolved oxygen and may also due to the thermal mismatch between oxide and substrate. The adsorption of protective layer containing lignin was temporary adsorbed on the surface.
Metal-free carbonaceous nanomaterials have witnessed a renaissance of interest due to the surge in the realm of nanotechnology. Among myriads of carbon-based nanostructures with versatile dimensionality, one-dimensional (1D) carbon nanotubes (CNTs) and zero-dimensional (0D) carbon dots (CDs) have grown into a research frontier in the past few decades. With extraordinary mechanical, thermal, electrical and optical properties, CNTs are utilized in transparent displays, quantum wires, field emission transistors, aerospace materials, etc. Although CNTs possess diverse characteristics, their most attractive property is their unique photoluminescence. On the other hand, another growing family of carbonaceous nanomaterials, which is CDs, has drawn much research attention due to its cost-effectiveness, low toxicity, environmental friendliness, fluorescence, luminescence and simplicity to be synthesized and functionalized with surface passivation. Benefiting from these unprecedented properties, CDs have been widely employed in biosensing, bioimaging, nanomedicine, and catalysis. Herein, we have systematically presented the fascinating properties, preparation methods and multitudinous applications of CNTs and CDs (including graphene quantum dots). We will discuss how CNTs and CDs have emerged as auspicious nanomaterials for potential applications, especially in electronics, sensors, bioimaging, wearable devices, batteries, supercapacitors, catalysis and light-emitting diodes (LEDs). Last but not least, this review is concluded with a summary, outlook and invigorating perspectives for future research horizons in this emerging platform of carbonaceous nanomaterials.
The gene encoding a cellobiohydrolase 7B (CBH7B) of the thermophilic fungus Thielavia terrestris was identified, subcloned, and expressed in Pichia pastoris. CBH7B encoded 455 amino acid residues with a molecular mass of 51.8 kDa. Domain analysis indicated that CBH7B contains a family 7 glycosyl hydrolase catalytic core but lacks a carbohydrate-binding module. Purified CBH7B exhibited optimum catalytic activity at pH 5.0 and 55 °C with 4-methylumbelliferryl-cellobioside as the substrate and retained 85% of its activity following 24 H incubation at 50 °C. Despite the lack of activity toward microcrystalline substrates, this enzyme worked synergistically with the commercial enzyme cocktail Cellic(®) CTec2 to enhance saccharification by 39% when added to a reaction mixture containing 0.25% alkaline pretreated oil palm empty fruit bunch (OPEFB). Attenuated total reflectance Fourier transform infrared spectroscopy suggested a reduction of lignin and crystalline cellulose in OPEFB samples supplemented with CBH7B. Scanning electron microscopy revealed greater destruction extent of OPEFB strands in samples supplemented with CBH7B as compared with the nonsupplemented control. Therefore, CBH7B has the potential to complement commercial enzymes in hydrolyzing lignocellulosic biomass.
Pectin and modified pectin differ in the structure of the chains in which the modified version of pectin is shorter in length, non-branched, and galactose-rich. These differences in structure may be exploited for the removal of heavy metals. Durian (Durio zibethinus) rind, that is regarded as agri-food waste was processed into durian rind pectin (DRP) and modified durian rind pectin (mDRP). DRP and mDRP were evaluated as biosorbent for removal of toxic heavy metals (Pb(II), Cd(II), Cu(II), Zn(II) and Ni(II)) and were compared with two commercial products; citrus pectin (CP) and modified citrus pectin (MCP). In general, the order of removal of heavy metals by all biosorbents was Cu(II) > Pb(II) > Ni(II) > Zn > Cd(II). Except for the removal of Pb(II), the order of effectiveness of heavy metal removal of the biosorbents was MCP > mDRP > CP > DRP. MCP, a commercial biosorbent showed the best biosorbent ability, and mDRP a waste product from durian was also a favorable sorber that should be considered for sorption and removal of heavy metals.
With a view to understanding the effect of rare earth element (Ce, Pr, Nd, Sm and Gd) substitution for the La site in LaMnO3 (LMO), the samples were prepared via solid-state reaction. Structure investigation by X-ray diffraction (XRD) showed that structure transformation from trigonal (LMO) to orthorhombic (PMO, NMO, SMO and GMO) occurred when smaller trivalent rare earth element was replaced. The MnO6 octahedra were tilted and elongated or compressed, corresponding to the ionic radii of the rare earth inserted. Meanwhile, microstructure study using scanning electron microscopy (SEM) illustrated that La substitution by another rare earth element caused a reduction in grain size. This might due to the changes in enthalpy of fusion by other rare earth ions, where higher enthalpy of fusion favours formation of smaller grain size. However, CeMnO3 did not form under this preparation condition. The magnetic properties studied from the hysteresis plot taken at room temperature indicated that the substitution of La with other magnetic trivalent rare earth ions strongly weakened the magnetic strength of the system.
The present study aimed to assess the effects of anthropogenic activities on the heavy metal levels in the Langat River by transplantation of Corbicula javanica. In addition, potential ecological risk indexes (PERI) of heavy metals in the surface sediments of the river were also investigated. The correlation analysis revealed that eight metals (As, Co, Cr, Fe, Mn, Ni, Pb and Zn) in total soft tissue (TST) while five metals (As, Cd, Cr, Fe and Mn) in shell have positively and significantly correlation with respective metal concentration in sediment, indicating the clams is a good biomonitor of the metal levels. Based on clustering patterns, the discharge of dam impoundment, agricultural activities and urban domestic waste were identified as three major contributors of the metals in Pangsun, Semenyih and Dusun Tua, and Kajang, respectively. Various geochemical indexes for a single metal pollutant (geoaccumulation index (I geo), enrichment factors (EF), contamination factor (C f) and ecological risk (Er)) all agreed that Cd, Co, Cr, Cu, Fe, Mn, Ni and Zn are not likely to cause adverse effect to the river ecosystem, but As and Pb could pose a potential ecological risk to the river ecosystem. All indexes (degree of contamination (C d), combined pollution index (CPI) and PERI) showed that overall metal concentrations in the tropical river are still within safe limit. River metal pollution was investigated. Anthropogenic activities were contributors of the metal pollution. Geochemical indexes showed that metals are within the safe limit.
The purpose of this investigation was to determine the antioxidant potentials and anti-glucosidase activities of six tropical medicinal plants. The levels of phenolic constituents in these medicinal plants were also quantified and compared. Antioxidation potentials were determined colorimetrically for scavenging activities against DPPH and NO radicals. Metal chelating assay was based on the measurement of iron-ferrozine absorbance at 562 nm. Anti-diabetic potentials were measured by using α-glucosidase as target enzyme. Medicinal plants' total phenolic, total flavonoid and hydroxycinnamic acid contents were determined using spectrophotometric methods, by comparison to standard plots prepared using gallic acid, quercetin and caffeic acid standards, respectively. Radical scavenging and metal chelating activities were detected in all medicinal plants, in concentration-dependent manners. Among the six plants tested, C. nutans, C. formosana and H. diffusa were found to possess α-glucosidase inhibitory activities. Spectrophotometric analysis indicated that the total phenolic, total flavonoid and hydroxycinnamic acid contents ranged from 12.13-21.39 mg GAE per g of dry sample, 1.83-9.86 mg QE per g of dry sample, and 0.91-2.74 mg CAE per g of dry sample, respectively. Our results suggested that C. nutans and C. formosana could potentially be used for the isolation of potent antioxidants and anti-diabetic compounds. To the best of our knowledge, this study represents the first time that C. nutans (Acanthaceae family) was reported in literature with glucosidase inhibition activity.
There is a global need to use plants to restore the ecological environment. There is no systematic review of phytoremediation mechanisms and the parameters for environmental pollution. Here, we review this situation and describe the purification rate of different plants for different pollutants, as well as methods to improve the purification rate of plants. This is needed to promote the use of plants to restore the ecosystems and the environment. We found that plants mainly use their own metabolism including the interaction with microorganisms to repair their ecological environment. In the process of remediation, the purification factors of plants are affected by many conditions such as light intensity, stomatal conductance, temperature and microbial species. In addition the efficiency of phytoremediation is depending on the plants species-specific metabolism including air absorption and photosynthesis, diversity of soil microorganisms and heavy metal uptake. Although the use of nanomaterials and compost promote the restoration of plants to the environment, a high dose may have negative impacts on the plants. In order to improve the practicability of the phytoremediation on environmental restoration, further research is needed to study the effects of different kinds of catalysts on the efficiency of phytoremediation. Thus, the present review provides a recent update for development and applications of phytoremediation in different environments including air, water, and soil.
We report herewith the study of fingernail clippings obtained from the residents of Tokyo, Japan. A total of 18 participants with no health problems and occupational exposure to metals were recruited to provide fingernails samples for this study. Through the use of instrumental neutron activation analysis (INAA), 18 elements (Ag, Al, As, Ca, Cl, Co, Cu, Fe, Hg, K, Mg, Mn, Na, S, Sb, Se, V, and Zn) were determined. The results showed that the toxic elements in the fingernails are in the lower range when compared to literature values. There were no chronic exposures to toxic elements such as As and Hg found. The level of Hg found is lower than that reported 20 years ago, possibly due to the strict regulation control in Japan on the release of Hg to the environment. The elements Se and Zn are found to be rather uniformly distributed among participants and are in agreement with results from other countries. There were no significant differences in elemental concentrations due to genders and smoking habits. The overall data from this study showed similar concentrations to those of healthy participants from other countries. Thus, the current data could represent the background level of elemental concentrations in fingernails of residents in Tokyo, which could serve as reference values for future study.
Microcystins-LR (MC-LR) which is a kind of potent hepatotoxin for humans and wildlife can be biodegraded by microbial community. In this study, the capacity of biofilm in degrading MC-LR was investigated with and without additional metal ions (Mn(2+), Zn(2+) and Cu(2+)) at the concentration of 1 mg L(-1). The results indicated that the degradation rate of MC-LR by biofilm was inhibited by introduced Mn(2+) and Cu(2+) during the whole culture period. MC-LR cannot be degraded until a period of culture time passed both in the cases with Zn(2+) and Cu(2+) (2 and 8 days for Zn(2+) and Cu(2+), respectively). The results of mlrA gene analysis showed that the abundance of MC-LR degradation bacteria (MCLDB) in the microbial community under Mn(2+) condition was generally lower than that under no additional metal ion condition. Meanwhile, a two days lag phase for the proliferation of MCLDB occurred after introducing Zn(2+). And a dynamic change of MCLDB from Cu(2+) inhibited species to Cu(2+) promoted species was observed under Cu(2+) condition. The maximum ratio of MCLDB to overall bacteria under various conditions during culture process was found to follow the tendency as: Cu(2+) > Zn(2+) ≈ no additional metal ion (Control) > Mn(2+), suggesting the adverse effect of Mn(2+), no obvious effect of Zn(2+) and positive effect of Cu(2+) on the distribution ratio of MCLDB over the biofilm.