A series of polycrystalline samples (La1-xSmx)0.67Sr0.33MnO3 (X=0.00, 0.05 and 0.10) were prepared using the conventional solid-state reaction method. The XRD analysis indicated that all the samples were fully crystalline and in a single phase with a rhombohedral structure after a sintering at 1200ºC for 24 hours in air. Meanwhile, the Atomic Force Microscopy measurements showed that a small amount of Sm doping in La sites affected the grain growth and this might affect the grain boundary layer, thus resulting in the reduction of the Curie temperature, TC. Extrinsic magnetoresistance (MR) was observed for all the samples with a large negative MR at low field (0-0.1 or 0.2T) region, followed by a slower varying MR at high field (0.1 or 0.2-1T). The highest low-field MR value of -4.6% (at 0.1T) and -6.1% (at 0.2T) were observed for sample X=0.10 and X=0.05, respectively. Hence, these indicated that the extrinsic MR was grain size dependent and was therefore enhanced with a small amount of Sm substitution in La sites.
Chlorella is one of the common microalgae found in a wide range of habitats, including Antarctica. Chlorella UMACC 234 is an interesting isolate in the collection of Antarctic microalgae in the University of Malaya algae culture collection (UMACC) as it grows well at temperatures much higher than the ambience. The alga was isolated from snow samples collected from Casey, Antarctica. This study investigates the influence of nitrogen source on the growth, biochemical composition and fatty acid profile of Chlorella UMACC 234. The cultures were grown in Bold’s Basal Medium with 3.0 mM NaNO3, NH4Cl or urea. The cultures grown on NaNO3 attained the highest specific growth rate (μ = 0.43 day–1) while the specific growth rates of those grown on NH4Cl and urea were not significantly different (p > 0.05). The urea-grown cells produced the highest amounts of lipids (25.7% dry weight) and proteins (52.5% dry weight) compared to those grown on other nitrogen sources. The cell numbers attained by the cultures grown at NaNO3 levels between 0.3 and 3.0 mM were similar but decreased markedly at 9.0 mM NaNO3. The fatty acids of Chlorella UMACC 234 were dominated by saturated fatty acids, especially 16:0 and 18:0. The percentage of polyunsaturated fatty acids was very low, especially in cells grown on urea (0.9% total fatty acids). Characterisation of the growth and biochemical composition of this Antarctic Chlorella is important to our studies on the relationship of Chorella isolates from tropical, temperate and polar regions, especially in terms of phylogeny and stress adaptation.
The consequence of postoperative infections associated with orthopaedic or biomaterial-associated implants is devastating to both the patients and the surgeons. Bacterial microcolonies adhere to the surface of implants, forming biofilms and then detaching part of itself into free-floating planktonic forms may be the cause of recurrent and persistent infections. These bacteria are very resistant towards antibiotics and require a higher drug concentration than usual in order to eradicate them. Quorem-sensing is regarded as one mechanism of communication or integration between these microorganisms in the biofilm and may even be in the transfer of resistant genes. Disruption of this pathway is regarded as one method of inhibiting its growth and formation. Implant design, technique and stability of fixation as well as the surface characteristics, the material and its biocompatibility may also influence bacterial adhesion. It has been suggested that multi-prong strategies such as prevention and disruption of biofilm formation, parenteral antibiotics, use of antibiotic-impregnated construction materials and altering the intrinsic properties of the implant surface may help to eradicate this menace.
Even though a lot of new advanced materials have been developed nowadays, steel remains a major material in construction, automobiles, appliances, industrial machinery as well as in the nuclear industry. Due to steel easily corroded, a proper surface protection is required to avoid any failures and extended the life cycle of the components. Surface coating is an efficient and economical method to obtain desirable material surfaces properties. Hot dip aluminizing technique was utilized in this study. Experiments have been conducted on the mild steel substrates with 12mm diameter. Prior to hot dipping process, observation on grain growth at three different temperatures had also been conducted to understand the behaviour of steel under application of heat. The substrates were heated at 700ºC, 800ºC and 900ºC for 1 hour and the microstructure was analyzed. The temperature of 800C was chosen for hot dipping. The substrates were dipped into the molten aluminum maintained at temperature 800ºC for 2,4,6,8,10,15 and 20 minutes. Optical microscopy and energy dispersive X-ray spectroscopy were used in this investigation. From the microstructure observation, it showed the appearance of intermetallic layer covered by the top layer of Al on the mild steel substrate increased with the increase in dipping time ranging from 36 to 282μm. The result of EDX analysis revealed the existence of Fe and Al in form of Fe2Al5 phase for all the dipping time.
An antimicrobial (AM) Active Packaging can be made by incorporating and immobilizing suitable AM agents into food package matrices and applying a bio switch concept. A starchbased film was prepared and incorporated with an antimicrobial agent, i.e. lysozyme with EDTA as a chelating agent. This film was then inoculated with the bacteria Escherichia coli and Bacillus subtilis to carry out the microbial contamination study. The inhibition of both E. coli and B. subtilis by the AM film was clearly observed as a clear zone formation in the culture agar test. The film appearance showed that lysozymes could give a better inhibition to the growth of E. coli and to B. subtilis, at a satisfying inhibition rate. From the broth test, the decreased in the optical densities were found to be 65.83% and 91.30%, suggesting an effective growth inhibition of E. coli and B. subtilis, respectively. Physically, the film which was incorporated with lysozymes was found to be slightly different from the control film. The moisture content of the film, with lysozymes, was found to be below 10.5%, as compared to the control, after 24 hours of formation in the storage at ambient temperature.
The production of ethanol, from glucose in batch and fed batch culture, was investigated. In the fed batch culture, the glucose feeding was added into the culture at 16th hour of fermentation. The effects of different glucose concentration feeding rates on ethanol fermentation were investigated for fed batch culture. The 2gL-1hr-1 glucose concentration feeding rate was found to give higher ethanol yield (2.47 g ethanol g glucose-1), with respect to substrate consumed as compared to 8 gL-1hr-1 (0.23 g ethanol g glucose-1) and 4 gL-1hr-1 (0.20 g ethanol g glucose-1). The ethanol yield with respect to substrate consumed obtained in batch culture was 0.81 g ethanol g glucose-1. The fed batch culture at 2 gL-1hr-1 glucose concentration feeding rate was proven to be a better fermentation system than the batch culture. The specific growth rate, specific glucose consumption rate and specific ethanol production rate for the fed batch fermentation, at 2 gL-1hr-1 glucose concentration feeding rate, were 0.065 hr-1, 1.20 hr-1 and 0.0009 hr-1, respectively.
Complicated crown-root fractures are rare and often need complex treatment planning. This paper describes a simplified treatment option for a complicated crown root fracture that minimally encroached into the biologic region in a growing child without the need for surgery or orthodontic treatment.
Silicon nanowires were synthesized on Si substrates (111) via thermal evaporation using AuPd thin layer catalyst. Pre cleaned of Si wafer was used as a substrate to assemble the nanostructure products. In this work, the effect of growth temperature that ranging from 800 to 1000°C on the formation of silicon nanowires studied extensively. X-ray diffraction and field emission scanning electron microscope were employed to characterize the structures and morphology of nanowires. Vertical aligned silicon nanowires have been successfully grown on Si substrates at 900 and 1000°C. At 1100°C, the high aspect ratio of silicon nanowires can be produced but the formation density is low. The presence of AuPd catalyst on the tip of nanowires, it is expected that VLS is the most suitable to explain the growth mechanism of obtained SiNWs. The crystalline structure of SiNWs was proved by XRD data.
The state of Selangor, Malaysia, is facing a significant rise in the number of malaria cases with the incidence varying from 20 to 90 per 100,000 persons in a population. A study was carried out to describe the distribution of malaria cases in relation to the growing number of foreign workers in Selangor. Data were reviewed using the return forms "PBV (M) 101", a summary of malaria cases in Selangor for 2006 and Annual Reports of Vector-Borne Disease Control Unit, Selangor State Department for 2001- 2005. The malaria cases in Selangor varied between 172 cases in 2001 and 90 cases in 2006. Most of the cases were contributed by foreign workers, who were predominantly male of economically active age group and came from malaria endemic countries. Most of these cases were concentrated in the urban districts. Malaria is still endemic in Selangor. Malarial infection has the potential of contributing to an urban outbreak of malaria.
This study aim to evaluate antimicrobial efficacy of sodium hypochlorite (NaOCl) and ozonated water against Enterococci faecalis biofilm. The bacterial biofilm was exposed to 2.62%, 1.31% NaOCl and 0.1 ppm ozonated water over a range of time periods. The presence of viable cells was determined by enumeration of colony forming units (CFU). All experiments were repeated four times (n=4). The effectiveness of the agents was compared using nonparametric Kruskal- Wallis test. The result revealed that 2.62% of NaOCl can completely kill E. faecalis biofilm in 15 minutes whereas 1.31 % NaOCl required a longer time to produce such effect. 0.1 ppm ozonated, however, did not exhibit any antimicrobial effect within the period of time tested. From this study, it can be concluded that 0.1 ppm ozonated water was not comparable with 2.62% and 1.31% NaOCl in antimicrobial efficacy against E. faecalis biofilm.
At present, research in composite materials is being directed at using natural fibres instead of synthetic fibres. Kenaf which is extensively grown in the Far East including Malaysia, has been identified as a bast (stem) fibre with significant market potential. In this work, long and random kenaf fibres (non-woven mat form) were used in the as-received condition and alkalized with a 0.06M NaOH solution. They were combined with polypropylene thin sheets, sandwiched between layers of kenaf fibres and hot-pressed to form natural fibre composites. The mechanical properties of the composites were investigated to observe the effect of fibre alignment, fibre treatment and pre-irradiation method used. A general trend was observed whereby alkalized and long fibre composites gave higher flexural modulus and flexural strength compared with random mat and untreated fibres. The long fibre composites also gave a higher work of fracture. However, the correlation between fibre surface treatment and the work of fracture was less clear. Pre-irradiation on the polypropylene pellets and fibres before the composite is manufactured showed significant improvement on the flexural modulus and flexural strength. The bond performance test performed on the treated composites demonstrated good bonding and interfacial adhesion between the fibre and matrix. However, the method of moulding used need to be improved to optimize the performance of the composites.
Varicella or chickenpox is an infectious disease caused by Varicella Zoster Virus (VZV), which commonly affects the children. It is a mild, self-limiting disease and rarely complicate to serious conditions except in adults. Decreasing incidence of chickenpox among children, probably owing to improved living conditions ,prevention and health care, is worrisome as growing number of adults are being infected. This creates disturbing concerns in many parties as women at childbearing age might get infected and not only are them at a great risk of serious complications, but also their unborn fetus or their newborn babies.
Neck abscess is still common in developing countries. Often the presentation is late especially when the pain becomes intolerable or the airway is compromised. Intramuscular abscess in the neck is very rarely encountered. We report a case of an abscess of the right sternocleidomastoid. The culture grew Proteus mirabilis. The outline of management is discussed.
Texture evolution of NiO formed during oxidation of polycrystalline single oriented (100) Ni-Cr was investigated. This foil was also termed rolling assisted biaxially textured substrate (RABiTS). X-ray diffractograms of oxidized Ni-Cr RABiTS foil showed the existence of mostly (200) NiO indicating (100)-type NiO formed exclusively on (100) singly oriented Ni-Cr grains. Epitaxial relationship between the two layers is observed. However the dual-in-plane texture was recorded.
The in-plane texture was assessed by conducting phi scan and plotting series of pole figures measured at (111) NiO peak. The mechanism of the oxides formation was proposed to take into account the formation of (100)-type NiO. Cross section morphology of the oxidised foils reveals two oxidation layers; fast growing external layer consisting of the (100)-type NiO and an internal layer consisted of mostly Cr2O3 and maybe NiCr2O4. The thickness of NiO was ~ 10Pm. Cr2O3 formed as needle-like oxides embedded in a matrix of Ni foil. Inward diffusion of oxygen is believed to have caused this to happen. The external NiO layer was consisted of duplex microstructure characterised by columnar layer growing vertical on the surface of the metal and a few micron thick of equiaxed NiO. Delamination of the outer NiO layer often occurred at the columnarequiaxed interface which could be cured by CeO2 deposition on the foil prior to the oxidation process. CeO2 was deposited by conversion immersion using Ce(NO3)3.6H2O solution. (200) NiO formed on this coated sample as well.
We put attention on Intrinsic Josephson Junction (IJJ) to study the fundamental physic for device applications. Convenient self-flux method was used to grow BSCCO single crystals. We investigated the lid effect to examine the single crystal growth of high TC (Critical Temperature). We found that for the crystal growth with no lid, two stage transitions of TC ≅ 61 K and 77 K were observed. While for the crystal growth with lid, the BSCCO has TC ≅ 80K, ΔTC = 10K and approximately average size5x2mm 2 . When we increased weight of lid, the single crystal have increased to TC =80K, ΔTC = 4K and the typical size was ≅7x3mm 2 . TC and the crystal growth show a tendency to increase by the effect of the lid. From observed quasi-particle characteristics, c-axis direction changed from semiconductor to intrinsic Josephson characteristic with decreasing temperature.
Ceramic of BaxSr1-xTiO3 (BST) for x =0.3; 0.5 and 0.7 were successfully deposited by solid solution method. The BST ceramic were analyzed by x-ray diffraction (XRD). The XRD spectra was recorded on a Philips type PW 3701 diffractometer using CuKD (Oco = 1.54056 Å) radiation at 30 KV and 30 mA (900 watt). The spectra shows that BST ceramic are polycrystalline with tetragonal structure. The lattice constants analysis of the grown ceramics was analyzed by visual basic program. Using Cohen’s and Cramer’s algorithms in visual basic program, , the lattice constants are a = b = 3.877 Å; c = 3.970 Å for Ba0.3Sr0.7TiO3 ceramic, a = b = 3.979 Å; c = 3.981 Å. for Ba0.5Sr0.5TiO3 ceramic and a = b = 3.965 Å; c = 4.005 Å for Ba0.7Sr0.3TiO3 ceramic, respectively. The reform value of the lattice constant of BST ceramic is possibly associated with the anti site defects of Ba and Sr.
Natural radionuclides such as 210 Po and 210 Pb were analyzed in soft part of cockle (Anadara granosa) obtained from Kuala Selangor in the west coast Peninsular of Malaysia. The activity levels of both nuclides fluctuated within the size of cockles from 41.3 ± 2.5 Bq/kg to 114 ± 7 Bq/kg and 12.9 ± 1.7 Bq/kg to 96.8 ± 5.3 Bq/kg in dry weight (dwt) for 210 Po and 210 Pb, respectively. The level activity in wet weight (wwt) also varied from 8.60 ± 0.52 Bq/kg to 25.70 ± 1.63 Bq/kg and 2.47 ± 0.40 Bq/kg to 19.27 ± 1.05 Bq/kg for 210 Po and 210 Pb, respectively, probably related to the different of metabolic rate and growth of cockles. Activity ratio of 210 Po/ 210 Pb in dry weight also fluctuated from 0.93 to 6.41 with not related to the decay of 210 Pb.
Breast-feeding offers many benefits to the baby and the mother. For instance, breast milk provides the right balance of nutrients to help an infant grow into a strong and healthy toddler. Even though breastfeeding is a natural process, it is not always easy. In certain situations, some mothers are unable to breastfeed their babies or the babies are unable to adapt to breastfeeding. This will lead to the use of bottle-feeding. The effect of breast-feeding and bottle-feeding on physical growth has been well established but less has been concentrated on the craniofacial growth and dental development. This review reveals the effects of breast-feeding and bottle-feeding on craniofacial growth and dentoalveolar development based on the available literature.
The purpose of this study was to examine the effect of stimulus sweep direction on the fine structure of the 2f1-f2 distortion product otoacoustic emission (DPOAE). It was hypothesised that the DPOAE fine structure could be shifted if the stimulus sweep changed from one direction to the other. In the present study, ascending, descending and random frequency sweeps were used, with f2 frequency varying between 992 Hz and 2496 Hz and f2/f1 fixed at 1.22. DPOAE fine structure was recorded at 16 Hz intervals. Screening, spontaneous otoacoustic emission (SOAE) and DPOAE measurements were carried out on 19 ears of 19 subjects aged between 22 and 30 years. Data from 14 ears that had at least one significant peak or valley in their DPOAE fine structure were included in the main analysis. Of these, five ears showed at least one occurrence of SOAE over the frequency span 600 Hz to 2500 Hz. Data for ears with and without SOAEs were grouped and analysed separately. The results showed no effect of sweep direction on DPOAE fine structure. No significant differences were observed in peak or valley frequencies, peak height or valley depth between the three stimulus sweep conditions (p > 0.05). There was also no significant effect of stimulus sweep direction on DPOAE level at the point at which SOAE frequency equalled DPOAE frequency (p > 0.05). In conclusion, the study found no effect of stimulus sweep direction on the fine structure of the 2f1-f2 DPOAE, either in ears with or without SOAEs. Therefore, future measurements of this fine structure may use either sweep direction.
This paper outlines the past five decades of scientific interests and advances in medicinal plant research in Malaysia. Initially the prime interest of research programmes has been on phytochemical studies leading to the discovery of biologically active compounds as chemical templates to produce new drug candidates. As the Malaysian herbal medicine market experiences an extraordinary growth, the research approaches taken have recently included activities to develop herbal medicines into quality, efficacious and safe products for human consumption. Advances in chromatographic and spectroscopic techniques have had a tremendous impact on the isolation and structure elucidation of the constituents of medicinal plants. The development of a series of bioassay methodologies and utilization of bioassay-guided isolation techniques have contributed significantly to the progress of medicinal plant research in Malaysia. Research work on some medicinal plants carried out by the local scientists will be illustrated as examples.