A gene encoding a thermotolerant lipase with broad pH was isolated from an Antarctic Pseudomonas strain AMS3. The recombinant lipase AMS3 was purified by single-step purification using affinity chromatography, yielding a purification fold of approximately 1.52 and a recovery of 50%. The molecular weight was approximately ∼60 kDa including the strep and affinity tags. Interestingly, the purified Antarctic AMS3 lipase exhibited broad temperature profile from 10-70 °C and stable over a broad pH range from 5.0 to pH 10.0. Various mono and divalent metal ions increased the activity of the AMS3 lipase, but Ni(2+) decreased its activity. The purified lipase exhibited the highest activity in the presence of sunflower oil. In addition, the enzyme activity in 25% v/v solvents at 50 °C particularly to n-hexane, DMSO and methanol could be useful for catalysis reaction in organic solvent and at broad temperature.
Although carbon dioxide (CO2) is well known as one of the major green-house gases, it is also an economical C1 resource. Thus, CO2has been regarded as an appealing starting material for the synthesis of polymers, like polycarbonates by the reaction with epoxides. Herein the reaction between natural epoxidized soybean oil (ESO), propylene oxide (PO) and CO2under high pressure (4.0MPa) with the presence of Co-Zn double metal cyanide (Co-Zn DMC) catalyst was studied. Temperature and reaction time were varied accordingly and the products obtained were characterized by FTIR, GPC and1H NMR. The results obtained indicate the formation of polycarbonates in the samples collected with yields vary from 60 to 85%. The number average molecular weight (Mn) of the resultant polymer prepared at reaction temperature of 80°C and reaction time of 6h can reach up to 6498g/mol.
Poly(3-hydroxybutyrate-co-4-hydroxybutyrate) [(P(3HB-co-4HB)] copolymer receives attention as next generation biomaterial in medical application. However, the exploitation of the copolymer is still constrained since such copolymer has not yet successfully been performed in industrial scale production. In this work, we intended to establish pilot production system of the copolymer retaining the copolymer quality which has recently discovered to have novel characteristic from lab scale fermentation. An increase of agitation speed has significantly improved the copolymer accumulation efficiency by minimizing the utilization of substrates towards cell growth components. This is evidenced by a drastic increase of PHA content from 28 wt% to 63 wt% and PHA concentration from 3.1 g/L to 6.5 g/L but accompanied by the reduction of residual biomass from 8.0 g/L to 3.8 g/L. Besides, fermentations at lower agitation and aeration have resulted in reduced molecular weight and mechanical strength of the copolymer, suggesting the role of sufficient oxygen supply efficiency in improving the properties of the resulting copolymers. The KLa-based scale-up fermentation was performed successfully in maintaining the yield and the quality of the copolymers produced without a drastic fluctuation. This suggests that the scale-up based on the KLa values supported the fermentation system of P(3HB-co-4HB) copolymer production in single-stage using mixed-substrate cultivation strategy.
This article reports on the structural characteristics and antioxidant activity of unmodified autohydrolyzed ethanol organosolv lignin (AH EOL) extracted from oil palm fronds (OPF) and modified autohydrolyzed ethanol organosolv lignin via incorporation of p-nitrophenol (AHNP EOL). The isolated lignin were analyzed by FTIR, (1)H and (13)C NMR spectroscopy, 2D NMR; HSQC and HMBC, CHN analysis, molecular weight distribution using GPC analyzer, thermal analysis; TGA and DSC. The chemical modification by utilizing an organic scavenger during delignification process provided smaller lignin fragments and enhanced the solubility of lignin by reducing its hydrophobicity properties. It was revealed that the antioxidant properties increased as compared to the unmodified organosolv lignin. Additionally, the modified lignin has better solubility in water (DAHNP EOL=35%>DAH EOL=25%).
In this present study, a series of polymer electrolyte thin films were synthesized by incorporating different ratios of lithium triflate (LiCF3SO3) in a low molecular weight polyvinyl chloride (PVC) matrix by the solution casting technique. The incorporation of LiCF3SO3 suppressed the high degree of crystallinity in PVC enabling the system to possess an appreciable ionic conductivity. The ionic conductivity of the samples, with different LiCF3SO3 content, was determined by the aid of ac impedance spectroscopy. The highest ionic conductivity of 4.04 10–9 S cm–1 was identified for the composition of PVC: LiCF3SO3 (75:25). Further understanding of the ionic conductivity mechanism was based on temperature-dependent conductivity data which obeyed Arrhenius theory, indicating that the ionic conductivity enhancement was thermally assisted. The possible dipole-dipole interaction between the chemical constituents was confirmed with changes in cage peak, analysed using Fourier transform infrared spectroscopy.
The β-1,6-glucanases are ubiquitous enzymes which appear to be implicated in the morphogenesis and have the ability to become virulence factor in plant-fungal symbiotic interaction. To our knowledge, no report on ß-1,6-glucanases purification from Trichoderma longibrachiatum has been made, although it has been proven to have a significant effect as a biocontrol agent for several diseases. Therefore, the aim of this study was to purify β-1,6- glucanase from T. longibrachiatum T28, with an assessment on the physicochemical properties and substrate specificity. β-1,3-glucanase enzyme, from the culture filtrate of T. longibrachiatum T28, was successively purified through precipitation with 80% acetone, followed by anionexchange chromatography on Neobar AQ and chromatofocusing on a Mono P HR 5/20 column. (One β-1,6-glucanase) band at 42kDa in size was purified, as shown by the SDS-PAGE. The physicochemical evaluation showed an optimum pH of 5 and optimum temperature of 50°C for enzyme activity with an ability to maintain 100% enzyme stability. Enzyme activity was slightly reduced by 10-20% in the presence of 20 mM of Zn2+, Ca2+, Co2+, Mg2+, Cu2+, Mn2+ and Fe2+. The highest β-1,6-glucanase hydrolysis activity was obtained on pustulan due to the similarity of β-glucosidic bonds followed by laminarin, glucan and cellulose. Therefore, it can be concluded that the characterization of ß-1,6-glucanase secreted by T. longibrachiatum in term of molecular weight, responsed to selected physicochemical factors and the substrate specificity are approximately identical to other Trichoderma sp.
Background: Many proteins released by cells to the blood and other fluids are glycoproteins. One set of glycoproteins carry the ABO blood group determinants and glycoproteins have been shown to be vital in determining the structure and organization of plasma membranes. There is evidence suggesting their important role in cell-to-cell contact, adhesion, hormone interaction and vital transformation. Differences in proteins and glycoproteins in the different human blood groups may influence the invasion process of Plasmodium falciparum. The objectives of the study were to determine whether there are any changes in proteins and glycoproteins of red blood cells upon infection by P. falciparum and whether these protein and glycoprotein changes differ in the various ABO blood groups.
Methods: A Malaysian strain of P. falciparum was cultured in vitro in red blood cells from A, B, O and AB blood groups. Protein and glycoprotein profiles of uninfected and P. falciparum- infected red blood cells from the different human ABO blood groups were analyzed by SDS-PAGE. For protein bands, the gels were stained with Coomassie blue while glycoproteins were visualized following staining of gels using GelCode ® Glycoprotein Staining Kit.
Results: Cell membranes of P. falciparum infected erythrocytes from different ABO blood groups have different glycoprotein profiles compared to uninfected cells. All the infected samples showed a prominent protein band of molecular weight 99 kDa which was not present in any of the uninfected samples while a 48 kDa band was seen in four out of the seven infected samples. The erythrocyte cell membranes of A and AB blood groups showed different glycoprotein profiles upon infection with P. falciparum when compared to those from blood groups B and O.
Conclusion: The two glycoproteins of molecular weights 99 kDa and 48 kDa should be further studied to determine their roles in the pathogenesis of malaria and as potential targets for drug and vaccine development.
HCFCs, in addition to destroying the ozone layer, have been recognized as a contributing factor that increases global warming. It is widely used as working fluid in window air-conditioning system, where capillary tube serves as an expansion device. Literature reports have shown that no single refrigerant can solve the problem of ozone layer depletion and global warming. Refrigerant HC290/HC600a/HFC407C mixture, an eco-friendly refrigerant, has been recognized as an alternative to HCFC22. The objective of this study is to, for cost effectiveness, develop an empirical correlation to predict the refrigerant HC290/ HC600a/HFC407C mixture mass flow rate using statistical experimental design approach. A review of relevant literature shows that refrigerant’s mass flow rate depends on condensing temperature, degree of subcooling, inner diameter and length of capillary tube. The relationship between the mass flow rate and the four independent variables was established as an empirical mathematical correlation using central composite design (CCD), a response surface methodology (RSM). This empirical correlation was examined using analysis of variance (ANOVA) of 5% level of significance. The results of these analysis showed that the correlation fitted well with the experimental data yielding an average and standard deviation of 1.05% and 2.62%, respectively. The validity of the present correlation was further assessed by comparing it with published empirical correlation in literature and the result showed that the present correlation is consistent.
Long carbon chain alkanediols are used in the production of poly(3-hydroxybutyrate-co-4-hydroxybutyrate) [P(3HB-co-4HB)], however these substrates possess high toxicity towards bacterial cells. This study demonstrated the effective utilisation of a long carbon chain alkanediol, namely 1,8-octanediol, to enhance the yield and production of a copolymer with a high molecular weight of over 1000 kDa, which is desirable for novel applications in medical and biopharmaceuticals. The increased PHA content (47-61 wt%) and concentration (1.7-4.5 g/L) was achieved by additional feeding of a combination of C4 substrates at C/N 10, with 1,8-octanediol + γ-butyrolactone producing P(3HB-co-22 mol% 4HB) with a high molecular weight (1060 kDa) and elongation at break of 970%. The DO-stat feeding strategy of C/N 10 has shown an increment of PHA concentration for both carbon combination, 0.45-4.27 g/L and 0.32-3.36 g/L for 1,8-octanediol + sodium 4-hydroxybutyrate (4HB-Na) and 1,8-octanediol + γ-butyrolactone, but with a slight reduction on molecular weight and mechanical strength. Nonetheless, further study revealed that a nitrogen-absence feeding strategy could retain the high molecular weight and elongation at break of the copolymer, and simultaneously improving the overall P(3HB-co-4HB) production.
Lignosus rhinocerotis has a long history of use by the indigenous community within East Asia to treat a range of health conditions including asthma and chronic cough. To date, there is limited scientific evidence to support its therapeutic effects in relieving these airways conditions. In this study, we examined the effects of the different molecular weight fractions [high-molecular-weight (HMW), medium-molecular-weight (MMW), and low-molecular-weight (LMW)] obtained from the cold water sclerotial extract (CWE) of L. rhinocerotis on airways patency using airway segments isolated from Sprague Dawley rat in an organ bath set-up. It is demonstrated that the HMW and MMW fractions exhibited higher efficacy in relaxing the pre-contracted airways when compared to the CWE and LMW fraction. In addition, the HMW fraction markedly supressed carbachol-, 5-hydroxytrptamine-, and calcium-induced airway contractions. CWE demonstrated a lower efficacy than the HMW fraction but it also significantly attenuated carbachol- and calcium-induced airway contractions. Results showed that the bronchorelaxation effect of CWE and fractions is mediated via blockade of extracellular Ca2+ influx. The composition analysis revealed the following parts of carbohydrate and proteins, respectively: HMW fraction: 71 and 4%; MMW fraction: 35 and 1%; and LMW fraction: 22 and 0.3%. Our results strongly suggest that the polysaccharide-protein complex or proteins found in the HMW and MMW fractions is likely to contribute to the bronchorelaxation effect of CWE.
A revision of a metal-on-ultra high molecular weight (UHMWPE) bearing couple for total hip replacement was performed due to aseptic loosening after 23 years in-vivo. It is a major long-term failure identified from wear generation. This study includes performing failure analysis of retrieved polyethylene acetabular cup from Zimmer Trilogy® Acetabular system. The UHMWPE acetabular cup was retrieved from a 61 years old male patient with ability to walk but limited leg movement when he presented to hospital in early 2016 with complaint left thigh pain. It was 23 years after his primary total hip replacement procedure. Surface roughness and morphology condition were measured using 3D laser microscope and Scanning Electron Microscope (SEM) to evaluate and characterize the wear features on polyethylene acetabular cup surface. ATR-Fourier Transform Infra-Red (ATR-FTIR), differential scanning calorimetry (DSC) and gel permeation chromatography (GPC) were used to characterize the chemical composition of carbon-oxygen bonding, crystallinity percentage and molecular weight of the polymer liner that might changes the mechanical properties of polyethylene. Nano indentation is to measure hardness and elasticity modulus where the ratio of hardness to elastic modulus value can be reflected as the degradation of mechanical properties. A prominent difference of thickness between two regions resulted from acentric loading concentration was observed and wear rate were measured. The linear wear rate for thin side and thick side were 0.33 mm/year and 0.05 mm/year respectively. Molecular weight reduction of 57.5% and relatively low ratio of hardness to elastic modulus (3.59 × 10-3) were the indicator of major mechanical properties degradation happened on UHMWPE acetabular cup. This major degradation was contributed by oxidation and polishing wear feature accompanied with delamination, craters, ripple and cracks were the indication of extensive usage of UHMWPE from the suggested life span of acetabular cup application.
An extractive bioconversion conducted on soluble starch with cyclodextrin glycosyltransferase (CGTase) enzyme in ethylene oxide-propylene oxide (EOPO)/potassium phosphates liquid biphasic system (LBS) to extract gamma-cyclodextrin (γ-CD) was examined. A range of EOPO (with potassium phosphates) molecular weights was screen to investigate the effect of the latter on the partioning efficency of CGTase and γ-CD. The results show that the optimal top phase γ-CD yield (74.4%) was reached in 35.0% (w/w) EOPO 970 and 10.0% (w/w) potassium phosphate with 2.0% (w/w) sodium chloride. A theoretical explanation for the effect of NaCl on γ-CD was also presented. After a 2 h bioconversion process, a total of 0.87 mg/mL concentration of γ-CD was produced in the EOPO/ phosphates LBS top phase. After the extraction of top phase from LBS, four continuous repetitive batches were successfully conducted with relative CGTase activity of 1.00, 0.86, 0.45, and 0.40 respectively.
The increase in the price of commercial succinic acid has necessitated the need for its
synthesis from waste materials such as glycerol. Glycerol residue is a waste product of
Oleochemical production which is cheaply available and a very good source of carbon.
The use of immobilized cells can further reduce the overall cost of the production process.
This study primarily aims to produce succinic acid from glycerol residue through the use
of immobilized Escherichia coli in a batch fermentation process. The parameters which
affect bacterial fermentation process such as the mass substrate, temperature, inoculum
size and duration of fermentation were screened using One-Factor-At-a-Time (OFAT)
method. The result of the screening process shows that a substrate (glycerol) concentration
of 30 g, inoculum size 20% v/v, and time 4 h produced the maximum succinic acid
concentration of 117.99 g/L. The immobilized cells were found to be stable as well as
retain their fermentative ability up to the 6th cycle of recycling, thereby presenting as an
advantage over the free cell system. Therefore, conclude that using immobilized cells can
contribute immensely to the cost-effective production of succinic acid from glycerol
residue.
The formation of aqueous two-phase system (ATPS) with the environmentally friendly and recyclable ionic liquid has been gaining popularity in the field of protein separation. In this study, the ATPSs comprising N,N-dimethylammonium N',N'-dimethylcarbamate (DIMCARB) and thermo-responsive poly(propylene) glycol (PPG) were applied for the recovery of recombinant green fluorescent protein (GFP) derived from Escherichia coli. The partition behavior of GFP in the PPG + DIMCARB + water system was investigated systematically by varying the molecular weight of PPG and the total composition of ATPS. Overall, GFP was found to be preferentially partitioned to the hydrophilic DIMCARB-rich phase. An ATPS composed of 42% (w/w) PPG 1000 and 4.4% (w/w) DIMCARB gave the optimum performance in terms of GFP selectivity (1,237) and yield (98.8%). The optimal system was also successfully scaled up by 50 times without compromising the purification performance. The bottom phase containing GFP was subjected to rotary evaporation of DIMCARB. The stability of GFP was not affected by the distillation of DIMCARB, and the DIMCARB was successfully recycled in three successive rounds of GFP purification. The potential of PPG + DIMCARB + water system as a sustainable protein purification tool is promising.
Lignin from kenaf (Hibiscus cannabinus) core was investigated as an alternative filler for rubber. Three types of extraction methods were used to isolate lignin from kenaf, namely kraft, soda and organosolv process. The particle size, surface area, functionalities changes, molecular weight and thermal properties of the lignin were characterized. The results showed that Kraft lignin (KL) has the smallest particle size (40.41 μm) compared to soda lignin (SL) (63.85 μm) and organosolv lignin (OL) (66.85 μm). This is in good agreement with the BET surface area of 9.52 m2/g, 1.25 m2/g and 2.40 m2/g respectively. However, the smaller surface area of SL compared to OL is due to the smaller pore size and pore volume of SL. KL also showed high hydroxyl content with corresponding high thermal stability as confirmed by NMR and TGA. The thermal stability of the lignin correlates well with the molecular weight (MW). From the overall characteristics, it can be concluded that KL, SL and OL can be used as an alternative filler in rubber compounds to substitute common fillers like silica and carbon.
Two inorganic pigments (TiO2 and SiO2) were used to prepare composites with polyaniline (PANI) by situ polymerization method. PANI and PANI composites with SiO2 and TiO2 were characterized using Fourier transform infrared spectroscopy and X-ray diffraction. The morphology of the synthesized pigments (PANI , PANI-SiO2 and PANI-TiO2) was examined using scanning electron microscopy. Samples were then used as pigments through blending them with acrylic paint and applied on the surface of carbon steel panels. Corrosion was evaluated for coating of carbon steel panels through full immersion test up to standard ASTMG 31. Mass loss was calculated after they have been exposed in acidic media. A digital camera was also used for monitoring corrosion visually on the surface of carbon steel specimens. The results revealed that acrylic paint pigmented by PANI-SiO2 composite was more efficient in corrosion protection for carbon steel compared with the other synthesized pigments.
This study was conducted to evaluate umami taste in protein hydrolysate produced from green mussel (Perna viridis) by hydrolysing with flavorzyme at pH 8, enzyme substrate ratio (E/S) 3% with or without the presence of 0.4% sodium tripolyphosphate (STPP) and 1.5% NaCI. Degree of hydrolysis (DH), yield, amino acid compositions, molecular weight distribution and sensory evaluation were determined. The highest DH (23.18%), darkest color and highest yield (8.34%) were recorded for hydrolysate produced in the presence of both STPP and NaCI. Electrophoresis analysis showed the presence of protein bands between 10 to 70 kDa where hydrolysate with addition of STPP and NaCI had bands with lower intensities. Amino acids which contribute to the umami taste such as glutamic acid, glycine and aspartic acid were higher in hydrolysate produced with STPP and NaCI addition. The hydrolysate has lesser fishy odor and flavor than those produced with only in the presence of flavorzyme and was also rated with highest score for all the five basic tastes including bitterness. However, the score for bitterness was still lower than the reference solutions. Therefore, green mussel hydrolysate produced in this study has a good potential as a food flavorant.
A search is presented for the single production of vector-like quarks in proton-proton collisions at
s
= 13
TeV
. The data, corresponding to an integrated luminosity of 35.9
fb
- 1
, were recorded with the CMS experiment at the LHC. The analysis focuses on the vector-like quark decay into a top quark and a W boson, with one muon or electron in the final state. The mass of the vector-like quark candidate is reconstructed from hadronic jets, the lepton, and the missing transverse momentum. Methods for the identification of b quarks and of highly Lorentz boosted hadronically decaying top quarks and W bosons are exploited in this search. No significant deviation from the standard model background expectation is observed. Exclusion limits at 95% confidence level are set on the product of the production cross section and branching fraction as a function of the vector-like quark mass, which range from 0.3 to 0.03
pb
for vector-like quark masses of 700 to 2000
GeV
. Mass exclusion limits up to 1660
GeV
are obtained, depending on the vector-like quark type, coupling, and decay width. These represent the most stringent exclusion limits for the single production of vector-like quarks in this channel.
The continuous depletion of global oil reserves with the propensity for light distillates
propels the oil and gas industry to explore heavier fractions of crude oils with significant
amount of paraffin waxes. However, the precipitation and deposition of waxes during the
transportation of these waxy crude oils in the pipelines contribute to several issues, such as
the flowability reduction, excessive pumping cost, and wax gel formation, that adversely
affect the supposedly steady offshore oil production. As a result, substantial resources are
expended to resolve these flow assurance problems. The wax inhibitors and pour point
depressants are developed and modified to meet the wax remediation criteria. Essentially,
the wax crystals are formed through the nucleation, growth, and agglomeration processes,
while the deposition of these waxes occurs via molecular diffusion and shear dispersion.
The wax inhibitors are able to control the growth of wax crystals through nucleation, cocrystallization,
adsorption, and dispersion interactions. This paper particularly assessed
the following compounds: (1) polymeric wax inhibitors, (2) nano-hybrid pour point
depressants, (3) organic solvents, and
(4) surfactants. Given the significance of
these compounds in the deposition and
precipitation of waxes, it is imperative to
comprehensively explore the types and
nature of these compounds and their recent
applications as well as to critically assess
their strengths and drawbacks, which were
addressed in this paper. Furthermore, the
challenges of using these compounds and the factors that govern their efficiencies were also discussed. Accordingly, the carbon
length and the molecular weight of both paraffin waxes and wax inhibitors are among the
most influential factors.
In this study, polyacrylonitrile (PAN) nanofiber membrane was prepared by an electrospinning technique. After alkaline hydrolysis, the ion-exchange nanofiber membrane (P-COOH) was grafted with chitosan molecules to form a chitosan-modified nanofiber membrane (P-COOH-CS). Poly(hexamethylene biguanide) (PHMB) was then covalently immobilized on P-COOH and P-COOH-CS to form P-COOH-PHMB and P-COOH-CS-PHMB, respectively. The nanofiber membranes were subjected to various surface analyses as well as to the evaluations of antibacterial activity against Escherichia coli. The optimal modification conditions for P-COOH-CS-PHMB were attained by water-soluble chitosan at 50 kDa of molecular weight, coupling pH at 7, and 0.05% (w/w) of PHMB. Within 10 min of treatment, the antibacterial rate was close to 100%. Under the similar conditions of antibacterial treatment, the P-COOH-CS-PHMB exhibited a better antibacterial efficacy than the P-COOH-PHMB. When the number of bacterial cells was increased by 2000 folds, both types of nanofiber membranes still maintained the antibacterial rate close to 100%. After five cycles of repeated antibacterial treatment, the antibacterial efficacy of P-COOH-PHMB was 96%, which was higher than that of P-COOH-CS-PHMB (83%). The experimental results revealed that the PHMB-modified nanofiber membranes can be suitably applied in water treatment such as water disinfection and biofouling control.