Atomic force microscopes (AFM) as one of the scanning probe microscopy (spm) modes have become useful tools, not only for observing surface morphology and nanostructure topography but also for fabrication of various nanostructures itself. In this work, silicon oxide (SiOx) patterns were formed on Si(100) surface by means of AFM anodization, where a non-contact mode used to oxidize Si wafer at the nanoscale size. The oxide patterns could serve as masks for the chemical etching of Si surface in alkaline solution in order to create the Si nanodots. A special attention is paid to finding relations between the size of dots and operational parameters as tip bias voltage and tip writing speed Dot arrays with 10 nm high and less than 50 nm in diameter have been successfully fabricated. The ability to control oxidation and scanning speed can be utilized in fabrication of complex nanostructures and make scanning probe lithography (SPL) as a very promising lithographic technique in nanoelectronic devices, nanophotonics and other high-tech areas.
In this study TiO2 films have been prepared using two different techniques i.e. sol-gel and electron gun evaporation (e-gun) techniques. The films were annealed at 300, 350 and 400oC in air. The microstructure study using field emission scanning electron microscope and x-ray diffractometer showed nanometer grains size and only the film prepared by sol-gel and annealed at 400oC has anatase phase while others are amorphous. To study the effect of the films (as buffer layer) onto the dielectric bolometer Ba0.6Sr 0.4TiO3 as distance sensor, sensors with the configuration of Al/BST/TiO2/RuO2/SiO2/Si were built. Two different measurements i.e. with and without infrared source were carried out to measure the sensitivity and repeatability of the sensors. The sensors which contained sol-gel TiO2 films gave reading for both type of measurements, indicating that the sensor can act as active and passive sensors. However, the sensors which contained e-gun TiO2 films only gave responses when the IR source was used, indicating that they can only act as passive sensors. The most sensitive sensor was TiO2 film prepared by sol gel and annealed at 350oC. In general sensors which contained TiO2 films prepared by sol gel showed good repeatability.
Co-synthesis of In2O3 and ZnO nanowires (NWs) were grown on silicon and alumina substrates using vapour transport deposition method. Their morphological structures showed that the NWs were rather aligned on silicon substrate and randomly oriented on alumina substrate. The formation of NWs on silicon substrate was found to be dominated by the growth of ZnO NWs while that on alumina substrate was dominated by the growth of In2O3 NWs. The In2O3 and ZnO NWs were highly crystalline and have wurtzite structure.
Bottom-contact pentacene OTFTs are fabricated using cross-linked poly(vinyl alcohol) (PVA) insulator and its reliability characteristics are analyzed. The hysteresis of the OTFTs is mainly caused by the electrons that are injected from the gate electrode to the cross-linked PVA insulator. To block the injection of electrons, plasma-enhanced chemical vapor deposition (PECVD) SiO2 layer is inserted between the gate electrode and the cross-linked PVA layer, so that the minimum hysteresis can be obtained. In addition, the effects of the gate bias stress as a function of time is investigated to examine the long-term reliability of the device during the operation.
Thin films of barium strontium titanate (Ba0.6Sr0.4TiO3) perovskite system are promising candidates for microelectronic devices that can be integrated with semiconductor technology. Ba0.6Sr0.4TiO3 thin films have been prepared onto BST/TiO2/RuO2/SiO2/Si substrate using the spin coating and sol-gel process. Then the samples were subsequently annealed at 600oC, 650oC and 700oC for 60 minutes in air. The microstructure and dielectric properties show that the crystallization improved as the annealing temperature was increased. All of the films have nanometer grain size. The average grain size of the films increased as the temperature was increased. The dielectric constant and ac conductivity of the films also increased as the average grain size increased. These results showed that the microstructure and dielectric properties depend on the annealing temperature.
Spatial and temporal variations in silica concentration were determined at various rivers and tributaries in the Linggi River Basin, which has been highly polluted due to urban, industrial and agricultural wastes. The silica content measured as reactive silicate in the whole Linggi River Basin ranged from 1.4 to 26.3 mg/L. A clear seasonal variation in silica was noted especially in the major rivers with higher concentration during dry months and lower concentration during the wet months. The concentration was found to decrease as the water flooded downstream. The large drainage area with granite dominated lithology and high denudation especially in the upper catchment is attributed for high silica content in the water of Linggi River Basin.
Infiltration caused by rainfall will lead to the changes of moisture content and soil pore water pressure or matric suction of the soil. These changes indicate the behavior of the soil especially during wetting and drying process. This paper presents the experimental test result of rain water infiltration into soil column for two samples of soils. The main objectives were to study the effect of rainfall intensity and duration of soil infiltration process for the forest soil and to compare its result to the gravelly sand. Infiltration experimental in this study involved three main components; water supply system, soil column and instrumentations, including percolation collection system. This study uses two types of tensiometers; 5 and 10 cm long. The results of TDR and tensiometers which were used to obtained moisture content and matric suction, respectively, shows that the system was successfully developed. For the forest soil, the result showed that moisture content of the top section is higher compared with the other sections. On the other hand, for gravelly sand, the moisture content in middle section is higher compared with the top and bottom section of the soil. Meanwhile, matric suction for both soils dropped during rainfall and gradually increases towards drying process. Other than that the comparison of soil matric suction between 5 and 10 cm tensiometers shows significant results for gravelly sand compared to forest soil.
Dry sliding wear of polyester hybrid composites containing carboxylic functionalized multi-walled carbon nanotubes (cNT) and microparticles, silica (Si02) was studied at different sliding distances. An attempt has been made to produce uniform dispersion of nano- and micro- particles in the test samples by ultrasonication. The tribological properties of the hybrid composites were performed by using pin-on-disc (POD) tester against grey cast iron countersurface. The dry sliding wear tests were carried out under pressure-velocity (pv) condition of 0.4 MPa and 4 m/s for total sliding distance of 28800 m and at an interval of every sliding distance of 3600 m, wear properties and behavior were studied. The samples containing 10 wt.% silica (microparticles) with and without CNT always show increase in coefficient of friction at the expense of wear rate. However, samples containing only ci'rr have the lowest wear rate with the increase in coefficient of friction. Sliding distance studies also provide the information on wear rates which were ever changing at different sliding distances whereas average coefficient of friction did not vary throughout the tests. SEM observations of wear surfaces showed different wear morphologies when reinforcement (cNT or Si02) incorporated into the composites either alone or in combination.
The mechanical properties of fractured rock mass are largely dependent on the fracture structure under the coupling of freeze-thaw cycles and large temperature difference. Based on the traditional macroscopic continuum theory, the thermal and mechanical model and the corresponding theories ignore the material internal structure characteristics, which add difficulty in describing the mesoscopic thermal and mechanical behavior of the fractured rock mass among different phases. In order to uncover the inherent relationship and laws among the internal crack development, structural change and the physical and mechanical properties of rock under strong cold and frost weathering in cold area, typical granite and sandstone in cold region were analyzed in laboratory tests. The SEM scanning technology was introduced to record the microstructural change of rock samples subject to freeze-thaw cycles and large temperature difference. Association rules between the microstructure and the physical mechanical properties of rock mass were analyzed. The results indicated that, with the increase of the cyclic number, the macroscopic physical and mechanical indexes and the microscopic fracture index of granite and sandstone continuously and gradually deteriorate. The width of original micro crack continues to expand and extend and new local micro cracks are generated and continue to expand. The fracture area and width of the rock increase and the strength of the rock is continuously damaged. In particular, the strength and elastic modulus of granite decrease by 20.2% and 33.36%, respectively; the strength and elastic modulus of sandstone decrease by 33.4% and 36.43%, respectively.
Siliceous mesoporous molecular sieve (Si-MCM-41) material with highly ordered hexagonal pore arrangement was synthesized at 373 K for 8-days duration by hydrothermal method, dried at 393 K and calcined at 823 K in N2 atmosphere. The calcined Si-MCM-41 was later functionalized with 10-50 wt. % monoethanolamine (MEA) by impregnation method and dried in vacuum at 343 K. The MEA-Si-MCM-41 samples were characterized for their physicochemical properties with FTIR, XRD, TGA, HRTEM, FESEM, BET and elemental analysis. XRD results showed that the intensity of the characteristic peaks of Si-MCM-41 reduces with increasing loading of MEA indicating that the MEA molecules are loaded in the pores as well as on the surface of Si-MCM-41. The appearance of FTIR peaks corresponding to N-H, C-N and C-H bonds suggested that Si-MCM-41 has been functionalized with MEA. The presence of Si-O-Si peaks in FTIR spectra of MEA-Si-MCM-41 samples indicates that the hexagonal pore arrangement remains intact and this is supported by HRTEM images. FESEM images show that MEA-Si-MCM-41 samples became agglomerated with increase loading of MEA. TGA analyses show that the MEA-Si-MCM-41 samples are thermally stable up to 528 K. N2 adsorption-desorption isotherms show that the textural properties of Si-MCM-41 material slowly change from a mesoporous material to non-porous material as the MEA loading increases due to pore filling effect during functionalization with MEA. Detection of N, C and H by elemental analysis confirms the presence of MEA in MEA-Si-MCM-41 samples.
Rayleigh surface acoustic waves (SAWs) have been demonstrated as a powerful and effective means for driving a wide range of microfluidic actuation processes. Traditionally, SAWs have been generated on piezoelectric substrates, although the cost of the material and the electrode deposition process makes them less amenable as low-cost and disposable components. As such, a "razor-and-blades" model that couples the acoustic energy of the SAW on the piezoelectric substrate through a fluid coupling layer and into a low-cost and, hence, disposable silicon superstrate on which various microfluidic processes can be conducted has been proposed. Nevertheless, it was shown that only bulk vibration in the form of Lamb waves can be excited in the superstrate, which is considerably less efficient and flexible in terms of microfluidic functionality compared to its surface counterpart, that is, the SAW. Here, we reveal an extremely simple way that quite unexpectedly and rather nonintuitively allows SAWs to be generated on the superstrate-by coating the superstrate with a thin gold layer. In addition to verifying the existence of the SAW on the coated superstrate, we carry out finite-difference time domain numerical simulations that not only confirm the experimental observations but also facilitate an understanding of the surprising difference that the coating makes. Finally, we elucidate the various power-dependent particle concentration phenomena that can be carried out in a sessile droplet atop the superstrate and show the possibility for simply carrying out rapid and effective microcentrifugation-a process that is considerably more difficult with Lamb wave excitation on the superstrate.
This paper describes the preparation, characterisation, and potential application of flexible palm oil-based polyurethane foam (PUF) as a support for iron-silica (Fe-Si) adsorbent. Fe-Si/polyurethane composite (Fe-Si/PUC) was prepared by impregnating Fe-Si adsorbent onto the surface of PUF by using a novel immersion-drying method. Morphological analysis of Fe-Si/PUC proved that Fe-Si was successfully impregnated onto the surface of PUF. Compression test and thermogravimetric analysis were carried out to determine the flexibility and thermal stability of Fe-Si/PUC, respectively. The Fe-Si/PUC removed 90.0% of 10 ppm methylene blue (MB) from aqueous solution in 60 min. The reusability study showed that Fe-Si/PUC removed 55.9% of MB on the seventh cycle. Hence, the synthesis of Fe-Si/PUC opens up a new path of implementing palm oil-based PUF to assist in the recovery of an adsorbent for environmental clean-up. The mechanism of physical interaction during the impregnation of Fe-Si adsorbent onto PUF was proposed in this paper.
This study was conducted to determine the influence of the oil palm boiler ash (OPBA) reinforcement on the microstructural, physical, mechanical and thermal properties of epoxy polymer composites. The chemical composition analysis of OPBA revealed that it contains about 55 wt.% of SiO2 along with other metallic oxides and elements. The surface morphology of OPBA showed angular and irregular shapes with porous structures. The influence of OPBA as a reinforcement in epoxy composite was studied with varying filler loadings (10-50 wt.%) and different particle sizes (50-150 μm). The result showed that the incorporation of OPBA in composites has improved the physical, mechanical and thermal properties of the epoxy matrix. The highest physical and mechanical properties of fabricated composites were attained with 30 wt.% loading and size of 50 μm. Also, thermal stability and the percentage of char residue of the composite increased with increasing filler loading. Furthermore, the contact angle of OPBA reinforced epoxy composites increased with the increase of filler loading. The lowest value of the contact angle was obtained at 30 wt.% of filler loading with the OPBA particle size of 50 μm. The finding of this study reveals that the OPBA has the potential to be used as reinforcement or filler as well as an alternative of silica-based inorganic fillers used in the enhancement of mechanical, physical and thermal properties of the epoxy polymer composite.
The dispersion of hyperaccumulators used in the phytoremediation process has caused environmental concerns because of their heavy metal (HM) richness. It is important to reduce the environmental risks and prevent the HM to reenter the ecological cycle and thereby the human food web. In this work, supercritical water gasification (SCWG) technology was used to convert Sedum plumbizincicola into hydrogen (H2) gas and to immobilize HMs into biochar. The H2 production correlated with temperature ranging from 380 to 440 ℃ with the highest H2 yield of 2.74 mol/kg at 440 ℃. The free-radical reaction and steam reforming reaction at high temperatures were likely to be the mechanism behind the H2 production. The analyses of bio-oil by the Gas Chromatography-Mass Spectrometer (GC-MS) and Nuclear magnetic resonance spectroscopy (NMR) illustrated that the aromatic compounds, oxygenated compounds, and phenols were degraded into H2-rich gases. The increase of temperature enhanced the HM immobilization efficiency (>99.2 % immobilization), which was probably due to the quickly formed biochar that helped adsorb HMs. Then those HMs were chemically converted into stable forms through complexation with inorganic components on biochar, e.g., silicates, SiO2, and Al2O3. Consequently, the SCWG process was demonstrated as a promising approach for dispersing hyperaccumulators by immobilizing the hazardous HMs into biochar and simultaneously producing value-added H2-rich gases.
Fast and efficient separation remains a big challenge in high performance liquid chromatography (HPLC). The need for higher efficiency and resolution in separation is constantly in demand. To achieve that, columns developed are rapidly moving towards having smaller particle sizes and internal diameters (i.d.). However, these parameters will lead to high back-pressure in the system and will burden the pumps of the HPLC instrument. To address this limitation, monolithic columns, especially silica-based monolithic columns have been introduced. These columns are being widely investigated for fast and efficient separation of a wide range of molecules. The present article describes the current methods developed to enhance the column efficiency of particle packed columns and how silica monolithic columns can act as an alternative in overcoming the low permeability of particle packed columns. The fundamental processes behind the fabrication of the monolith including the starting materials and the silica sol-gel process will be discussed. Different monolith derivatization and end-capping processes will be further elaborated and followed by highlights of the performance such monolithic columns in key applications in different fields with various types of matrices.
Glass ionomer cement (GIC) has theunique fluoride release property and able to formionic bond with tooth structure. However, the brittleness of the material results in low hardness. In the present study, a new approach in utilization of local waste materials as fillers for improvement of hardness of GIC is reported.The synthesized wollastonite and mine-silica by-product were individually incorporated into commercial GIC and the Vickers hardness were evaluated. The results shown that the incorporation of 1 % wollastonite into GIC gave ~ 6% increment in hardness compared to the control GIC (66.53H ±7.37 versus 62.66HV±2.98)but not for themine-silica. Thus, wollastonite could be a potential material to be utilized as fillersin dental restorative composite
Silicon, as the most important electronic material, has a lot of applications in the electronic industry and this includes the use of silicon in solar cells. One of the solar grade silicon production processes is the use of acid leaching for the removal of metallic impurities from silicon. The main advantage of this process for silicon purification is that it is based on a low temperature process. The purification of metallurgical grade silicon by acid leaching was studied as a function of time, temperature and etching. Based upon experimental results and under optimum conditions, it was possible to remove 41%, 71% and 25% of iron, calcium and aluminum respectively, with the use of aqua regia.
Compartmented Fluidized Bed Gasifier (CFBG), consisting of two compartments - the combustorand gasifier, uses air blown instead of pure oxygen for syngas production in bubbling fluidization mode, eliminating the need of air separation unit, and reducing the capital cost, thus distinguishes it from other traditional ones. Fluidization quality is a determining factor in the CFBG to guarantee its well-lifted behaviour. Previous study, without solid circulation at ambient conditions, brought to the fore the necessity of considering the effect of the minimum allowable effective diameter. The study was then performed in the CFBG cold physical model of 0.66m overall diameter (effective diameter for combustor and gasifier is 0.413m and 0.257m) to investigate the fluidization quality and compare it with the results obtained from the previous cold model of about 1.36 times smaller, but with the same compartmented ratio of 65:35. Different inert particles (river sand, quartz sand and alumina) were used, over a range of aspect ratios, for the aforementioned objective. The results showed that the fluidization quality in the gasifier has not been achieved and the degradation of fluidization quality in the combustor is still observed, notwithstanding the fact that the condition of the minimum allowable effective diameter has been met. The reduction of distributor free area, to increase the distributor pressure drop, showed a marginal effect on the quality. The effect of the minimum allowable effective diameter on fluidization quality in CFBG as well as the interplay of geometric and operational parameters require further studies be carried out. The fluidization quality of the binary mixture is also currently under investigation.
The purpose of this study is to measure and monitor the radon concentration from fabricated foamed light concrete, made of Portland cement, mine sand and granite. The concentration of radon released was measured using Radon Monitor Model 1027 from Sun Nuclear. The results of this research showed that the avearge radon concentration from foamed light concrete was 2.2 pCiL-1 L. Higher radon concentrations were detected after three days of measurements. Environment Protection Agency stated in its guidelines that radon concentration must lower than 4 pCiL-1 for a healthy environment. Thus, the use of foamed light concrete can be one of the alternatives to reduce radon concentration levels in human environment.
Measurement of low magnetic field has played an important role in many electronics applications such as navigation, military, non-destructive test, traffic detection as well as medical diagnosis and treatment. The presence of magnetic field, particularly its strength and direction, can be measured using magnetometer. There are many types of magnetometers being investigated through the years and one of the prominent types is fluxgate magnetometer. The main components of fluxgate magnetometer consisting of driving coils, sensing coils and magnetic core are developed by MEMS silicon processing technology. In this paper, an investigation on physical characteristics of the three-dimensional coil structure for a micro-scaled fluxgate magnetometer is presented. The physical characteristics such as width of the coil, distance between successive coils, and gap between the top and bottom coils which would influence the magnetic energy in magnetometer is discussed. In this work, finite-element method simulations to investigate the physical characteristics of the sensing coils were carried out, where the parameter of interest is the coils’ inductance as well as the magnetic flux density. Based on the simulation results, the varying of physical characteristics of the coils had its effects particularly in coil inductance, magnetic flux density, and magnetic energy. It could also be seen that the simulated results agreed with the theoretical aspects of magnetism in a coil. From the investigations, suitable coil dimensions were proposed.