This article provides an analytical solute transport model to investigate the potential of groundwater contamination by polluted surface water in a two dimensional domain. The clogging of streambed which makes the aquifer partially penetrated by the stream, is considered in the model. The impacts of pumping process, hydraulic conductivity and clogging layer on the quality of water produced from nearby drinking water wells are evaluated. It is found that results are consistent with numerical simulation conducted by MODFLOW software. Moreover, the model is applied using data of contamination occurrence in Malaysia, where high contaminants concentrations are found close to streams. Results show that the pumping activities (rate and time period) are crucial factors when evaluating the risk of groundwater contamination from surface water. Additionally, this study illustrates that the increase in either hydraulic conductivity or leakance coefficient parameters due to the clogging layer will enlarge the area of contamination. The model is able to determine the suitable pumping rate and location of the well so that the contamination plume never reaches the extraction well, which is useful in constructing riverbank filtration sites.
Iron(III)-poly(hydroxamic acid) resin complex has been studied for its sorption abilities with respect to arsenate and arsenite anions from an aqueous solution. The complex was found effective in removing the arsenate anion in the pH range of 2.0 to 5.5. The maximum sorption capacity was found to be 1.15 mmol/g. The sorption selectivity showed that arsenate sorption was not affected by chloride, nitrate and sulphate. The resin was tested and found effective for removal of arsenic ions from industrial wastewater samples.
Matched MeSH terms: Water Pollution, Chemical/prevention & control*
Steroid estrogens, such as estrone (E1), 17β-estradiol (E2), estriol (E3), and 17α-ethinylestradiol (EE2), are natural and synthetic hormones released into the environment through incomplete sewage discharge. This review focuses on the sources of steroid estrogens in wastewater treatment plants (WWTPs). The mechanisms and fate of steroid estrogens throughout the entire wastewater treatment system are also discussed, and relevant information on regulatory aspects is given. Municipal, pharmaceutical industry, and hospitals are the main sources of steroid estrogens that enter WWTPs. A typical WWTP comprises primary, secondary, and tertiary treatment units. Sorption and biodegradation are the main mechanisms for removal of steroid estrogens from WWTPs. The fate of steroid estrogens in WWTPs depends on the types of wastewater treatment systems. Steroid estrogens in the primary treatment unit are removed by sorption onto primary sludge, followed by sorption onto micro-flocs and biodegradation by microbes in the secondary treatment unit. Tertiary treatment employs nitrification, chlorination, or UV disinfection to improve the quality of the secondary effluent. Activated sludge treatment systems for steroid estrogens exhibit a removal efficiency of up to 100%, which is higher than that of the trickling filter treatment system (up to 75%). Moreover, the removal efficiency of advance treatment systems exceeds 90%. Regulatory aspects related to steroid estrogens are established, especially in the European Union. Japan is the only Asian country that implements a screening program and is actively involved in endocrine disruptor testing and assessment. This review improves our understanding of steroid estrogens in WWTPs, proposes main areas to be improved, and provides current knowledge on steroid estrogens in WWTPs for sustainable development.
Matched MeSH terms: Water Pollution, Chemical/statistics & numerical data*
Dissolved organic matter (DOM) was characterised in water samples sampled in the Lower Kinabatangan River Catchment, Sabah, Malaysia between October 2009 and May 2010. This study aims at: (i) distinguishing between the quality of DOM in waters draining palm oil plantations (OP), secondary forests (SF) and coastal swamps (CS) and, (ii) identifying the seasonal variability of DOM quantity and quality. Surface waters were sampled during fieldwork campaigns that spanned the wet and dry seasons. DOM was characterised optically by using the fluorescence Excitation Emission Matrix (EEM), the absorption coefficient at 340 nm and the spectral slope coefficient (S). Parallel Factor Analysis (PARAFAC) was undertaken to assess the DOM composition from EEM spectra and five terrestrial derived components were identified: (C1, C2, C3, C4 and C5). Components C1 and C4 contributed the most to DOM fluorescence in all study areas during both the wet and dry seasons. The results suggest that component C4 could be a significant (and common) PARAFAC signal found in similar catchments. Peak M (C2 and C3) was dominant in all samples collected during wet and dry seasons, which could be anthropogenic in origin given the active land use change in the study area. In conclusion, there were significant seasonal and spatial variations in DOM which demonstrated the effects of land use cover and precipitation amounts in the Kinabatangan catchment.
Matched MeSH terms: Water Pollution/statistics & numerical data
We report the first study on the occurrence of antibiotic-resistant enterococci in coastal bathing waters in Malaysia. One hundred and sixty-five enterococci isolates recovered from two popular recreational beaches in Malaysia were speciated and screened for antibiotic resistance to a total of eight antibiotics. Prevalence of Enterococcus faecalis and Enterococcus faecium was highest in both beaches. E. faecalis/E. faecium ratio was 0.384:1 and 0.375:1, respectively, for isolates from Port Dickson (PD) and Bagan Lalang (BL). Analysis of Fisher's exact test showed that association of prevalence of E. faecalis and E. faecium with considered locations was not statistically significant (p < 0.05). Chi-square test revealed significant differences (χ(2) = 82.630, df = 20, p < 0.001) in the frequency of occurrence of enterococci isolates from the considered sites. Resistance was highest to nalidixic acid (94.84 %) and least for chloramphenicol (8.38 %). One-way ANOVA using Tukey-Kramer multiple comparison test showed that resistance to ampicillin was higher in PD beach isolates than BL isolates and the difference was extremely statistically significant (p < 0.0001). Frequency of occurrence of multiple antibiotic resistance (MAR) isolates were higher for PD beach water (64.29 %) as compared to BL beach water (13.51 %), while MAR indices ranged between 0.198 and 0.48. The results suggest that samples from Port Dickson may contain MAR bacteria and that this could be due to high-risk faecal contamination from sewage discharge pipes that drain into the sea water.
Information on the pollution level and the influence of hydrologic regime on the stormwater pollutant loading in tropical urban areas are still scarce. More local data are still required because rainfall and runoff generation processes in tropical environment are very different from the temperate regions. This study investigated the extent of urban runoff pollution in residential, commercial, and industrial catchments in the south of Peninsular Malaysia. Stormwater samples and flow rate data were collected from 51 storm events. Samples were analyzed for total suspended solids, 5-day biochemical oxygen demand, chemical oxygen demand, oil and grease (O&G), nitrate nitrogen (NO3-N), nitrite nitrogen, ammonia nitrogen, soluble reactive phosphorus, total phosphorus (TP), and zinc (Zn). It was found that the event mean concentrations (EMCs) of pollutants varied greatly between storm characteristics and land uses. The results revealed that site EMCs for residential catchment were lower than the published data but higher for the commercial and industrial catchments. All rainfall variables were negatively correlated with EMCs of most pollutants except for antecedent dry days (ADD). This study reinforced the earlier findings on the importance of ADD for causing greater EMC values with exceptions for O&G, NO3-N, TP, and Zn. In contrast, the pollutant loadings are influenced primarily by rainfall depth, mean intensity, and max 5-min intensity in all the three catchments. Overall, ADD is an important variable in multiple linear regression models for predicting the EMC values in the tropical urban catchments.
Matched MeSH terms: Water Pollution, Chemical/statistics & numerical data*
A study on physico-chemical parameters and pathogenic bacterial community was carried out at the coastal waters of Pulau Tuba island, Langkawi. The physico-chemical parameters such as temperature (27.43-28.88 degrees C), dissolved oxygen (3.79-6.49 mg l(-1)), pH (7.72-8.20), salinity (33.10-33.96 ppt), total dissolved solids (32.27-32.77 g l(-1)) and specific conductivity (49.83-51.63 mS cm(-1)) were observed. Station 3 and station 4 showed highest amount of nitrates (26.93 and 14.61 microg at N l(-1)) than station 1 (2.04 microg at N l(-1)) and station 2 (4.18 microg at N l(-1)). The highest concentration (12.4 +/- microg l(-1)) of chlorophyll a was observed in station 4 in October 2005. High phosphorus content (561 microg P l(-1)) was found in the station 2. Thirteen bacterial isolates were successfully identified using API 20E system. The highest amount of bacteria was observed at Station 4 (3400 CFU ml(-1)) and the lowest numberwas at Station 2 (890 CFU ml(-1)). Out of identified 13 Gram-negative bacterial isolates dominant species were Aeromonas hydrophila, Klebsiella oxytoca, Pseudomonas baumannii, Vibrio vulnificus, Proteus mirabilis, Providencia alcalifaciens and Serratia liquefaciens. Apart from this, oil biodegrading Pseudomonas putida were also identified. The study reveals the existing status of water quality is still conducive and the reasonably diverse with Gram-negative bacteria along the Pulau Tuba Langkawi.
Field and laboratory studies were conducted to estimate concentration of potential contaminants from landfill in the underlying groundwater, leachate, and surface water. Samples collected in the vicinity of the landfill were analyzed for physiochemical parameters, organic contaminants, and toxic heavy metals. Water quality results obtained were compared from published data and reports. The results indicate serious groundwater and surface water contamination in and around the waste disposal site. Analysis of the organic samples revealed that the site contains polychlorinated biphenyls and other organo-chlorine chemicals, principally chloro-benzenes. Although the amount of PCB concentration discovered was not extreme, their presence indicates a potentially serious environmental threat. Elevated concentrations of lead, copper, nickel, manganese, cadmium, and cobalt at the downgradient indicate that the contamination plume migrated further from the site, and the distribution of metals and metals containing wastes in the site is nonhomogeneous. These results clearly indicate that materials are poorly contained and are at risk of entering the environment. Therefore, full characterization of the dump contents and the integrity of the site are necessary to evaluate the scope of the problem and to identify suitable remediation options.
Gadilam river basin has gained its importance due to the presence of Neyveli Lignite open cast mines and other industrial complexes. It is also due to extensive depressurization of Cuddalore aquifer, and bore wells for New Veeranam Scheme are constructed downstream of the basin. Geochemical indicators of groundwater were used to identify the chemical processes that control hydrogeochemistry. Chemical parameters of groundwater such as pH, electrical conductivity, total dissolved solids, sodium (Na(+)), potassium (K(+)), calcium (Ca(+)), magnesium (Mg(+)), bicarbonate (HCO(-)(3)), sulfate (SO(-)(4)), phosphate (PO(-)(4)), and silica (H(4)SiO(4)) were determined. Interpretation of hydrogeochemical data suggests that leaching of ions followed by weathering and anthropogenic impact controls the chemistry of the groundwater. Isotopic study reveals that recharge from meteoric source in sedimentary terrain and rock-water interaction with significant evaporation prevails in hard rock region.
Matched MeSH terms: Water Pollution, Chemical/statistics & numerical data
A study has been conducted to determine the composition of surfactants in runoff water in the semi-urban area of Bandar Baru Bangi, Selangor, Malaysia. Runoff samples were collected from five different locations with contrasting functional activities and the colorimetric method was used to analyze the concentrations of surfactants as methylene blue active substances (MBAS) for anionic surfactants and as disulphine blue active substances (DBAS) for cationic surfactants. The results showed that the highest surfactant concentrations of MBAS and DBAS in runoff water were recorded in the samples collected at the residential area, with the concentrations of 3.192 ± 0.727 and 0.170 ± 0.028 μmol/L, respectively. Anionic surfactants as MBAS were found to dominate the concentration of surfactants in both runoff and rainwater. The concentrations of both anionic and cationic surfactants in runoff water were recorded as being higher than in rainwater.
Matched MeSH terms: Water Pollution, Chemical/statistics & numerical data
Contamination of endocrine disrupting compounds (EDCs) in tap water is an emerging global issue, and there are abundant influencing factors that have an ambivalent effect on their transportation and fate. Different housing types vary in terms of water distribution system operation and design, water consumption choices, and other hydraulic factors, which potentially affect the dynamics, loadings, and partitioning of pollutants in tap water. Thus, this study analyzed 18 multiclass EDCs in tap water from different housing types (i.e., landed and high-rise) and the associated health risks. Sample analyses revealed the presence of 16 EDCs, namely hormones (5), pharmaceuticals (8), a pesticide (1), and plasticizers (2) in tap water, with the prevalent occurrence of bisphenol A up to 66.40 ng/L in high-rise housing. The presence of caffeine and sulfamethoxazole distribution in tap water was significantly different between landed and high-rise housings (t(152) = -2.298, p = 0.023 and t(109) = 2.135, p = 0.035). Moreover, the salinity and conductivity of tap water in high-rise housings were significantly higher compared to those in landed housings (t(122) = 2.411, p = 0.017 and t(94) = 2.997, p = 0.003, respectively). Furthermore, there were no potential health risks of EDCs (risk quotient water intake. However, EDC variation in different housing types requires simulation of the occurrence, transport, and fate of EDCs in the distribution system and investigation of the underlying factors for effective mitigation, prevention, and intervention.
Recently, the graphite based materials have gained interest as excellent platforms to remove aqueous pollutants via adsorption routes. This is given that such materials possess large specific surface area and low density. In the present work, a comparative study of two facile and effective approaches is conventional thermal heating and microwave irradiation methods to fabricate expanded graphite from available flake graphite sources of Vietnam for oil-contaminated water purification. The as-prepared expanded graphite was characterized by using FT-IR, SEM, XRD and BET analysis. The results exhibited that expanded graphite has multilevel pore structures and the surface area of expanded graphite obtained from microwave irradiation and conventional heating was 147.5 (m²/g) and 100.97 (m²/g) under optimal processing conditions. The as-synthesized expanded graphite from the microwave irradiation method was found to have higher adsorption capacities for diesel oil, crude oil, and fuel oil compared to conventional heating method.
A study of water quality parameters (temperature, conductivity, total dissolved solid, dissolved oxygen, pH and water hardness) in Ampang Hilir Lake was conducted in January, April, July and October 2010. The water quality parameters were tested and recorded at different sampling stations chosen randomly using Hydrolab Data Sonde 4 and Surveyor 4 a water quality multi probe (USA). Six metals which were cadmium, chromium, lead, nickel, zinc and copper were determined in five different compartments of the lake namely water, total suspended solids, plankton, sediment and fish. The metals concentration were determined by Inductively Coupled Plasma Mass Spectrometer (ICP-MS), Perkin Elmer Elan, model 9000.The water quality parameters were compared with National Water Quality Standard (NWQS Malaysia) while metal concentrations were compared with Malaysian and international standards. The study shows that water quality parameters are of class 2. This condition is suitable for recreational activities where body contact is allowed and suitable for sensitive fishing activities. Furthermore, metal concentrations were found to be lower than the international standards, therefore toxic effects for these metals would be rarely observed and the adverse effects to aquatic organisms would not frequently occur.
Matched MeSH terms: Water Pollution, Chemical/analysis*
This study investigates the spatial variation of water quality parameters in Sungai Setiu Basin at ten different locations from March 2010 to February 2011. The water quality was assessed using the Water Quality Index by Malaysian Department of Environment (DOE-WQI) and classified according to the Malaysia Interim National Water Quality Standard (INWQS). Six water quality parameters embedded in the DOE-WQI were dissolved oxygen (DO), biochemical oxygen demand (BOD), chemical oxygen demand (COD), pH, ammoniacal nitrogen (AN) and total suspended solid (TSS). In addition, this study also examined the changes in water quality over the past 10 years by comparing the present water quality to the previous works. The overall mean WQI value obtained was 84.0 which indicate that the Sungai Setiu basin is in clean condition and all measured water quality parameters gave value within the permissible limits of the INWQS classification except for pH which fall in Class III. It can be concluded that water quality in Sungai Setiu does not varies greatly over a decade. Hence continuous monitoring is needed to improve the water quality and minimize water pollution.
As the division of work within the world economic system becomes increasingly complex, the impact of disturbing events on the economic system is expanding. Recently, Japan proposed to discharge nuclear wastewater into the Pacific Ocean, which will cause damage to marine fisheries, thereby seriously affecting fisheries and other industries in Japan and other countries and regions around the world. Considering different scenarios of final and intermediate demand shifting, this paper uses the Inoperability Input-Output Model (IIM) and Multi-Region Input-Output Model (MRIO) to simulate the economic consequences of nuclear wastewater discharge in Japan and calculate the economic changes of each industry and country (region). The results show that: In the short term, when only the final demand for Japanese fishery products decreases. (1) The ten countries (regions) with significant economic losses are Japan, the United States, Chinese Taipei, Canada, Chile, South Africa, Mexico, Peru, the United Kingdom, and Ireland. (2) The ten countries (regions) with a significant increase in total output due to demand shift are China (People's Republic of), the Rest of the World, India, Indonesia, Viet Nam, the Philippines, Brazil, Myanmar, the Russian Federation, and Malaysia. (3) A ranking of changes in the total output of different industries. In the long term, when both intermediate and final demand for Japanese fishery products decrease. (4) The change in value added in Japan. (5) The change in value added of 67 countries (regions) worldwide. The ten countries (regions) with the most significant increase in value-added are the Russian Federation, China (People's Republic of), the Rest of the World, the United States, Indonesia, Australia, Norway, Korea, Viet Nam, and Myanmar. The ten countries (regions) with the most significant decrease in value-added are Japan, Chinese Taipei, Chile, South Africa, Peru, Thailand, Mexico, Cambodia, Costa Rica, and Morocco. Changes in value added of 45 industrial sectors worldwide.
The strategic location of Malaysia along the world's busiest trade waterways underscores the need to cope ballast water issues for both domestic and international shipping. The adoption of Ballast Water Management Convention 2004 (BWMC) by the International Maritime Organization is suitable for management plans intended to prevent the introduction of invasive species through ballast water discharge. Malaysia has ratified the BWMC in September 2010 and the Convention has come into force in September 2017. However up to now, the BWMC has not been fully implemented by Malaysia for ships operating in its waters. This paper analyse the headway in implementing the provisions of the BWMC in Malaysia as well as the issues and challenges encountered for the implementation. The paper concludes that Malaysian government should promulgate laws and policies to clearly communicate on ballast water issues to the shipping industry communities.
Matched MeSH terms: Water Pollution/legislation & jurisprudence; Water Pollution/prevention & control*
Population in urban centers in Kenya is increasing rapidly due to rural urban migration in search of better paying jobs. This migration has resulted in unauthorized settlements in the various urban centers. The income per capital of these people is less than a dollar a day. The amount of money is inadequate for survival and this has resulted into cultivating on open grounds for food crops. Unfortunately, these slums have come up along rivers, which carry, wastewater from household and industries. This wastewater is rich in heavy metals and the inhabitants of these areas use this contaminated water for irrigating their crops. The food crops from such areas have very high levels of heavy metals. The present study has screened Zea mays, Commelina bengalensis and Amaranthus hybridus for their ability to bioaccumulate these metals from contaminated soils using atomic absorption spectrophotometer (AAS). The results obtained showed that the C. bengalensis has high potential for removal of Cu, Pb and Cd metals as compared to the Zea mays and Amaranthus hybridus even though, results showed that C. bengalensis has a low potential for the removal of Zn as compared to Zea mays and Amaranthus hybridus.
In recent times, surface water resource in the Western Region of Ghana has been found to be inadequate in supply and polluted by various anthropogenic activities. As a result of these problems, the demand for groundwater by the human populations in the peri-urban communities for domestic, municipal and irrigation purposes has increased without prior knowledge of its water quality. Water samples were collected from 14 public hand-dug wells during the rainy season in 2013 and investigated for total coliforms, Escherichia coli, mercury (Hg), arsenic (As), cadmium (Cd) and physicochemical parameters. Multivariate statistical analysis of the dataset and a linear stoichiometric plot of major ions were applied to group the water samples and to identify the main factors and sources of contamination. Hierarchal cluster analysis revealed four clusters from the hydrochemical variables (R-mode) and three clusters in the case of water samples (Q-mode) after z score standardization. Principal component analysis after a varimax rotation of the dataset indicated that the four factors extracted explained 93.3 % of the total variance, which highlighted salinity, toxic elements and hardness pollution as the dominant factors affecting groundwater quality. Cation exchange, mineral dissolution and silicate weathering influenced groundwater quality. The ranking order of major ions was Na(+) > Ca(2+) > K(+) > Mg(2+) and Cl(-) > SO4 (2-) > HCO3 (-). Based on piper plot and the hydrogeology of the study area, sodium chloride (86 %), sodium hydrogen carbonate and sodium carbonate (14 %) water types were identified. Although E. coli were absent in the water samples, 36 % of the wells contained total coliforms (Enterobacter species) which exceeded the WHO guidelines limit of zero colony-forming unit (CFU)/100 mL of drinking water. With the exception of Hg, the concentration of As and Cd in 79 and 43 % of the water samples exceeded the WHO guideline limits of 10 and 3 μg/L for drinking water, respectively. Reported values in some areas in Nigeria, Malaysia and USA indicated that the maximum concentration of Cd was low and As was high in this study. Health risk assessment of Cd, As and Hg based on average daily dose, hazard quotient and cancer risk was determined. In conclusion, multiple natural processes and anthropogenic activities from non-point sources contributed significantly to groundwater salinization, hardness, toxic element and microbiological contamination of the study area. The outcome of this study can be used as a baseline data to prioritize areas for future sustainable development of public wells.
Matched MeSH terms: Water Pollution/statistics & numerical data*