Pressurized water reactor (PWR) type AP1000 is a third generation of a nuclear
power plant. The primary system of PWR using uranium dioxide to generate heat energy
via fission process. The process influences temperature, pressure and pH value of water
chemistry of the PWR. The aim of this paper is to transform the primary system of PWR
using fuzzy autocatalytic set (FACS). In this work, the background of primary system
of PWR and the properties of the model are provided. The simulation result, namely
dynamic concentration of PWR is verified against published data.
In this study, Single-Walled and Multi-Walled Carbon Nanotubes in their perfect forms were investigated by the Finite Element Method. Details on the modeling of the structure are provided in this paper, including the appropriate elements, the element properties that should be defined based on the atomic structure of Carbon Nanotubes and the corresponding chemical bonds. Non-covalent van der Waals interactions between two neighbor atoms as well as the required approximations for the modeling of the structures with this kind of interaction are also presented. Specific attention was dedicated to the necessity of using some time- and energy-consuming steps in the simulation process. First, the effect of simulating only a single ring of the whole structure is studied to find out if it would represent the same mechanical behavior as the long structure. Results show that by applying an appropriate set of boundary conditions, the stiffness of the shortened structure is practically equal to the long perfect structure. Furthermore, Multi-Walled Carbon Nanotube structures with and without defining the van der Waals force are studied. Based on the observations, applying the van der Waals force does not significantly influence the obtained Young's modulus of the structure in the case of a uniaxial tensile test.
The Green Turtle (Chelonia mydas) and Olive Ridley Turtle (Lepidochelys olivacea) are the only sea turtles with recorded landings in the Pulau Pinang coastal area. The Green Turtle has been the most abundant and widely distributed sea turtle in this area since it was first surveyed in 1995. Statistical analysis by the Pulau Pinang Department of Fisheries on the distribution of sea turtles from 2001 through 2009 has identified Pantai Kerachut and Telok Kampi as the most strongly preferred beaches for Green Turtle landings, with records for almost every month in every year. Green Turtle tracks and nests have also been found along the coast of Pulau Pinang at Batu Ferringhi, Tanjong Bungah, Pantai Medan, Pantai Belanda, Telok Kumbar, Gertak Sanggul, Moonlight Beach, Telok Duyung, Telok Aling, Telok Bahang and Telok Katapang. The Olive Ridley Turtle is present in smaller numbers; landing and nesting have only been recorded on a few beaches. There are no previous records of Olive Ridley landings at Pantai Kerachut and Telok Kampi, but tracks and nests have been found at Telok Kumbar, Tanjong Bungah, Pantai Medan, Telok Duyung and Gertak Sanggul. A Turtle Conservation Centre has been established at Pantai Kerachut to protect these species from extinction in Pulau Pinang. This paper presents details of the records and distribution of sea turtles in Pulau Pinang from 1995 through 2009.
Katabatic winds dramatically affect the polar climate. Their activity depends on density of air and temperature in the source region. This paper presents for first time an analysis of the precipitable water vapour (PWV) variability and its relation to a katabatic event at Scott Base station, Antarctica. A significant effect in their characteristics toward calculation of a reliable user accuracy in GPS applications is addressed. Our investigations using the data between 21st and 30th of November 2002 showed that the PWV profile exhibited an irregular pattern with a maximum value of 7.38 mm (~ 6 mm on average), and was more strongly influenced by relative humidity than by wind speed activity. The dominant wind flow during this period was from the North-Northeast (blowing from the Ross Sea) with a median speed of 4.96 ms–1. The PWV was high when the temperature was between –15ºC and –11ºC. During the dates identified as a katabatic event between 21:30 UT of 28th November and 18:40 UT on 29th November, the wind blew from the Southeast-South direction (from the Ross Ice Shelf) with a maximum speed of 10.92 ms–1. The PWV increased ~1.4 mm (23%) from the mean value, indicating severe wind during this event which had pronounced effect on GPS observations.
In the moving layer of particles with variable concentration, the shear estimation is not directly predictable and there is no existing clear mathematical or empirical formula to achieve this objective. This paper presents a developed approach to estimate the shear forces in a flow having suspended and moving layers of solid particles in liquid flow. The two-layer approach was taken whereby the flow consisting of one upper suspended layer of particles in the liquid, and the bottom layer was the moving bed of particles. In the present work, the method of finding the force acting on the pipe wall by the particles in the layer, termed as the ‘dry force’, was presented using a “pseudo hydrostatic pressure” method. To attain the equation for the dry force, a mathematical approach is taken with the assumptions that the flow is horizontal, two-phase pipe flow (solid in Newtonian liquid), incompressible and it is at steady-state. The analysis was conducted considering various particles densities, various concentrations in the suspended layer and different thicknesses of the moving bed. Changing the concentration in the suspended layer from 0.00001 up to 0.001 didn’t showed significant changes in the dry force evaluation. The dry friction force is increasing with increasing moving bed thickness. The developed mathematical model can be
applicable in solving for the shear force in horizontal solid liquid two-phase flows.
This paper presents a suitable and unique system for observing dielectrophoretic particle separation in a microfluidic device. Details presented on the experimental setup used will enable real time examination, monitoring and analysis of carboxylate-modified latex sphere particles in a colloidal mixture. Observations of the particles were made possible through an optical setup that illuminates the particles that went through the microelectrode array in the microchannel that was controlled by two analog signal generators. Through the setup, it was easily observed that the latex sphere particles move at a flow rate of 0.2 μl/s without colliding or overlapping on each other and successfully separated in two bands left and right. The new separation of one finest particles size for finest purification with respect to frequency was also observed, obtained and analysed.
The paper looks into the possibility of using standard addition method to analyse uranium and thorium in tin slag. Tin slag samples obtained from Butterworth was grind to 180 ȝm and injected with different concentrations of uranium and thorium. Linear calibration graphs were obtained for both these samples with R 2 values for uranium and thorium as 0.9989 and 0.9915 respectively. Based on this graphs, the initial uranium and thorium in the tin slag sample was established as 60 ppm for uranium and 160 ppm for thorium.
Nuclear power is considered as one of the best option for future energy development in Malaysia. Since Malaysia has no experience in nuclear energy generation, commissioning the first nuclear power plant needs tremendous effort in various aspects. Site selection is one of important step in nuclear power plant commissioning process. This paper proposes candidate sites for nuclear power plant in Mersing, Kota Tinggi, Muar and Batu Pahat district in Johor, Malaysia. The candidate selection process uses the IAEA document and AELB guideline as main reference, supported by site selection procedure by various countries. MapInfo Professional software was used to simulate the selection process for candidate areas for the nuclear power plant. This paper concluded that Tenggaroh and Jemaluang area are the most suitable area for nuclear power plant facilities in Johor, Malaysia.
Nuclear power is considered as one of the best option for future energy development in Malaysia. Since Malaysia has no experience in nuclear energy generation, commissioning the first nuclear power plant needs tremendous effort in various aspects. Site selection is one of important step in nuclear power plant commissioning process. This paper proposes candidate sites for nuclear power plant in Mersing, Kota Tinggi, Muar and Batu Pahat district in Johor, Malaysia. The candidate selection process uses the IAEA document and AELB guideline as main reference, supported by site selection procedure by various countries. Mapinfo Professional software was used to simulate the selection process for candidate areas for the nuclear power plant. This paper concluded that Tenygaroh and Jemaluang area are the most suitable area for nuclear power plant facilities in Johor, Malaysia.
Even though EDXRF analysis has major advantages in the analysis of stainless steel samples such as simultaneous determination of the minor elements, analysis can be done without sample preparation and non-destructive analysis, the matrix issue arised from the inter element interaction can make the the final quantitative result to be in accurate. The paper relates a comparative quantitative analysis using standard and standardless methods in the determination of these elements. Standard method was done by plotting regression calibration graphs of the interested elements using BCS certified stainless steel standards. Different calibration plots were developed based on the available certified standards and these stainless steel grades include low alloy steel, austentic, ferritic and high speed. The standardless method on the other hand uses a mathematical modelling with matrix effect correction derived from Lucas-Tooth and Price model. Further
improvement on the accuracy of the standardless method was done by inclusion of pure elements into the development of the model. Discrepancy tests were then carried out for these quantitative methods on different certified samples and the results show that the high speed method is most reliable for determining of Ni and the standardless method for Mn.
Shotcrete is a process where concrete is projected or “shot” under pressure, using a feeder or a
“gun” onto a surface to form structural shapes including walls, floors, and roofs. The surface can
be wood, steel, polystyrene, or any other surfaces that concrete can be projected onto. The surface
can be trowel led smooth while the concrete is still wet. Shotcrete has high strength, durability, low
permeability, excellent bond, and limitless shape possibilities. These properties allow shotcrete
to be used as a structural material in most cases. Although the hardened properties of shotcrete
are similar to conventional cast-in-place concrete, the nature of the placement process provides
additional benefits, such as excellent bond with most substrates and instant or rapid capabilities,
particularly on complex forms or shapes. In addition to building homes, shotcrete can also be used
to build pools. The practice of underground tunneling shows that the degree of stability of tunnels
is dependent on the state of the soil, rock mass, and shotcrete around the tunnel contour. The
development in the urban or suburban areas leads to the construction of tunnels in all kinds of soil
and rock. Meanwhile, the construction of tunnels in shallow depth or soft soils causes the ground
to displace. The determination of soil and rock mechanical properties to assess the stability of New
Austrian Tunnelling Method (NATM) tunnels and design the support system is one of the most
important steps in tunnelling. This paper provides information pertaining to the safety and increase
the stability of NATM tunnel before, during and after the operation of the tunnel. Therefore, the
shotcrete process is a recognized method for cemented sandy silt stabilization, with the aid of high
pressure shot concrete to increase the stability of tunnels.
One of the most interesting water management case studies in Iran is the case of Zayandehrud River, the main river that supplies water to Isfahan Province which is located in Gavkhuni River Basin (GRB). This paper examines the present and future demands for water and determines the extent to which water will be available for agricultural use by the year 2020. Although demand and supply conditions in 2000 were more or less in balance, there was an increase in the supply of some 28% by 2010 due to the completion of the third trans-basin diversion and the development of other local water sources. However, the demand exceeded its supply in 2010 and the basin fell into severe deficit. In this condition, the only way to keep supply and demand in balance is to reduce allocations to agriculture. By 2020, agriculture would only have 5% more water than the present and water supply is only 90% that of the normal, and this would then shrink from 2025 onwards. In other words, agriculture would have to be sacrificed in order to ensure full supplies of water for the other sectors. The scenarios examined reveal that a sustainable agriculture can only be accomplished by water saving practices and management measures, which may further lead to reduced demand, control supplies, and improve the efficiency of water use.
Lightning is a natural phenomenon that generates a high electric field during thunderstorm. It has been
reported that lightning strikes amid storms can occur around 100 times per second. The atmospheric
electric field is an imperative parameter during a thunderstorm. Therefore, monitoring the electric field
and its parameters is the best way for local lightning forecast. The electric field monitoring data can
validate the accuracy of weather prediction in a local area from meteorology department or by using
equipment specially designed to measure this electric field that exists when the phenomenon of lightning occurs. In this paper, the relationship between lightning, air humidity and temperature is discussed to understand the post lightning effect on these electric parameters. Additionally, the characteristics of the parameters are observed and analysed.
In recent years, vegetable oil such as Palm Oil (PO) has been identified as a potential alternative dielectric insulating fluid for transformers. It is biodegradable, non-toxic and has high flash and fire points. In this paper, a study on the positive lightning impulse breakdown voltages of PO under non-uniform field is carried out. The testing was carried out using needle-plane electrodes configuration at gap distances of 25 mm and 50 mm. Rising voltage, 1 and 3 shots per step testing methods were used and 3 types of Refined Bleach and Deodorized Palm Oil (RBDPO) and Mineral Oil (MO) were examined. It was found there is no significant effect on the breakdown voltages of all samples. The breakdown voltages of all RBDPO at 50% probability are comparable with MO. At 1% probability and gap distance of 50 mm, the breakdown voltages of all RBDPO are lower than MO.
This paper examined the significant relationship between government regulation and
construction waste management among Malaysian construction industries. Survey
was conducted among 10 contractors registered G7, using proportionate stratified
random sampling, out of which 10 questionnaire were collected for data analysis with
five point Likert scale categories of waste management from previous studies,
statistical analysis affirmed a significant positive relationship between government
regulation and construction waste management in Malaysian construction industries
through Statistical Package for the Social Sciences.
In this paper, the syntheses of kojic acid esters via chemical and enzymatic methods are
reviewed. The advantages and disadvantages of chemical process in term of process, safety and
efficiency are discussed. In enzymatic process, the significant process parameters related to the
synthesis of kojic acid esters such as the lipases, solvent, temperature and water content are
highlighted. Possible enzymatic synthesis using solvent and solvent-free system taking into
consideration of the difference in these systems involving cost, lipase reusability and efficiency
is comparatively reviewed. The possible approach for large scale production using various
enzyme reactor designs is also discussed and re-evaluated.
In this paper, we report the effect of BaAl2O4 addition (0-30 wt. %) on power consumption and oxygen sensing response of hot-spots developed on short Er123 ceramic rods of around 12 mm length synthesized using standard solid-state reaction. All the sensor rods showed increase in output current with increasing voltage followed by sudden reduction in output current and appearance of hot spot. After appearance of hot spot, for each rod, output current was observed to decrease gradually with increasing voltage with the slope of the I-V curve gradually approaching zero. Output current after the hot spot formation showed sensitivity to oxygen partial pressure, pO2 between 1 to 100 kPa. Addition of 30 wt. % BaAl2O4 reduced the fluctuation of current and increased the sensitivity for pO2 below 10 kPa. In addition, overshoot current was also reduced and resulted in improvement of response time from around 10 s to 5 s. Our result also showed that minimum power consumption was significantly reduced in the Er123 rods with 30 wt. % BaAl2O4.
The suction between soil particles is the basis and core problem in the study of unsaturated soil. However, is the suction between soil particles just the matrix suction (which has been widely used since the discipline of unsaturated soil mechanics was established). In fact, the concept of matrix suction is from soil science and reflects the water-absorbing capacity of the soil. Matrix suction characterizes the interaction between soil particles and pore water rather than the interactions between soil particles, which were not in conformity with the principle of effective stress of soils. The suction of unsaturated soil, in essence, is the intergranular suction composed of absorbed suction and structural suction. In this paper, first, the basic concepts of absorbed suction and structural suction were briefly introduced. Then, with soil mechanics, powder science, crystal chemistry, granular material mechanics and other related disciplines of knowledge for reference, the quantitative calculation formulas were theoretically deduced for the absorbed suction for equal-sized and unequal-sized unsaturated soil particles with arbitrary packing and the variable structural suction for equal-sized unsaturated soil particles with arbitrary packing and unequal-sized unsaturated soil particles with close tetrahedral packing. The factors that influence these equations were discussed. Then, the shear strength theory of unsaturated soil was established based on the theory of intergranular suction through the analysis of the effective stress principle of unsaturated soil. This study demonstrates that the shear strength of unsaturated soil consists of three parts: The effective cohesive force, the additional strength caused by external loads and the strength caused by intergranular suction. The contribution of the three parts to the shear strength of unsaturated soil depends on the following influence factors: Soil type, confining pressure, water content and density. Therefore, these factors must be comprehensively considered when determining the strength of an unsaturated soil.
In this work, the Sandvik uncoated carbide insert, CNGG 120408-SGF-H13A was used as a cutting tool in high-speed turning of titanium alloy Ti-6A1-4V EH (extra-low interstitial) with hardness of 32 HRC. Wear is one of the problems that cannot be avoided in machining process. Therefore, the objective of this paper was to investigate tool-wear behavior of various cutting-speed values (high-speed range) on the tool life of the cutting tools, especially in finishing titanium alloy. The experiments were performed under flooded coolant condition using water-based mineral-oil. The cutting speeds employed were 120, 170 and 220 mlmin. The feed rate was constant at 02 mm/rev and the depth of cut was 0.4 mm. Based on the results, the highest cutting speed of 220 m/min caused the highest wear rate. By linking the machine operations and the tool life curves obtained using flank wear data, the wear behavior of uncoated carbide was described.
The aim of this paper is to introduce a compact double-negative (DNG) metamaterial that exhibits a negative refractive index (NRI) bandwidth of more than 3.6 GHz considering the frequency from 2 to 14 GHz. In this framework, two arms of the designed unit cell are split in a way that forms a Modified-Z-shape structure of the FR-4 substrate material. The finite integration technique (FIT)-based Computer Simulation Technology (CST) Microwave Studio is applied for computation, and the experimental setup for measuring the performance is performed inside two waveguide ports. Therefore, the measured data complies well with the simulated data of the unit cell at 0-degree and 90-degree rotation angles. The designed unit cell shows a negative refractive index from 3.482 to 7.096 GHz (bandwidth of 3.61 GHz), 7.876 to 10.047 GHz (bandwidth of 2.171 GHz), and 11.594 to 14 GHz (bandwidth of 2.406 GHz) in the microwave spectra. The design also exhibits almost the same wide negative refractive index bandwidth in the major region of the C-band and X-band if it is rotated 90 degrees. However, the novelty of the proposed structure lies in its effective medium ratio of more than 4, wide bandwidth, and compact size.