Groundwater is the main source of water in the Kingdom of Saudi Arabia (KSA). A larger part of groundwater is founded in alluvial (unconfined) aquifers. Prediction of water table elevations in
unconfined aquifers is very useful in water resources planning and management. During the last two
decades, many aquifers in different regions of the KSA experienced significant groundwater decline.
The declines in these aquifers raised concerns over the quantity and quality of groundwater, as well
as concerns over the planning and management policies used in KSA. The main objective of this study was to predict water table fluctuations and to estimate the annual change in water table at an alluvial aquifer at wadi Hada Al Sham near Makkah, KSA. The methodology was achieved using numerical groundwater model (MODFLOW). The model was calibrated and then used to predict water table elevations due to pumping for a period of 5 years. The output of the model was found to be in agreement with the previous records. Moreover, the simulation results also show reasonable declination of water table elevations in the study area during the study period.
MeSH terms: Calibration; Models, Theoretical; Saudi Arabia; Water; Groundwater; Water Resources
The development of a new, low-cost building material that is composed of non-fired, pressed laterite bricks incorporating oil palm empty fruit bunches (OPEFB) fibre was investigated in this study. The main aim of this research was to study the physical and mechanical properties of laterite brick reinforced with OPEFB fibre, including dimensions, weight, density, water absorption and compressive strength. The tests were carried out according to BS 3921:1985 for water absorption and compressive strength tests. The mix proportion of the control bricks was 70% soil, 24% sand, and 6% cement. Meanwhile, the OPEFB fibre contents ranged from 1% to 5% by weight of cement. The specimens were taken from a total of 120 bricks. The findings withdrawn from this research were: firstly, the density of laterite bricks was decreased with the increase in the OPEFB fibre content of the bricks. Secondly, it was found that the addition of the OPEFB fibres improved the compressive strength of the bricks, and the maximum compressive strength determined in this study for bricks was with 3% fibre content. Finally, the water absorption results indicated a small increase in water absorption with the increase in the OPEFB fibre content in laterite bricks.
A Pressurized Liquid Extraction (PLE) method was developed by using conventional High Performance
Liquid Chromatography (HPLC). It was found that all of the PAHs have been successfully extracted with dichloromethane-acetone with high percentage recovery. A high temperature of 180°C gave the highest recovery for fluoranthene (94.4%). Meanwhile, fluorene showed the highest recovery at 150 bar, with 94.6% recovery. It is noted that there is no significant day-to-day difference in the efficiency of the developed method, with the R.S.D. values averaging at 0.02. The optimized conditions applied to the soil samples were analysed using the High Temperature High Performance Liquid Chromatography (HT-HPLC) with chromatographic conditions: Octadecylsilyl-silica (ODSsilica) column (100 mm × 4.6 mm I.D.); mobile phase acetonitrile:water 40:60 (v/v); flow rate 2.5 mL/min; temperature 70°C; UV absorbance 254 nm; injection volume 5µL.
MeSH terms: Acetone; Acetonitriles; Chromatography, High Pressure Liquid; Chromatography, Liquid; Fluorenes; Methylene Chloride; Silicon Dioxide; Soil; Temperature; Water
One of the compounds present in Pluchea indica extracts is antioxidant which plays an important role in inhibiting free radicals and thus protects humans against infections and degenerative diseases, such as cancer, arthritis, and ageing process. The main objective of this study was to investigate and determine the total phenolic compounds of Pluchea indica in different concentrations of ethanolic extracts. This species was chosen because of its high phytonutrient compounds with potential medicinal properties. There was a significant difference (P ≤ 0.05) in the total phenolic among the different parts of the tested plant. 50% of the ethanolic extract produced the highest total phenolic compounds (1775.00±86.00 to 658.95±5.00 µmol/g), followed by water extract (759.79±1.53 µmol/g) and 100% ethanol extract (352.72±22.30 to 249.29±5.37 µmol/g), respectively. In terms of the plant parts, the leaves contained the highest phenolic compounds (1775.00±86.00 µmol/g in 50% ethanol extract, 759.79±1.53 µmol/g in 100% aqueous extract and 352.72±22.30 µmol/g in 100% ethanol extract), followed by the stems (990.22±24.00 µmol/g in 50% ethanol extract, 990.22±24.59 µmol/g in 100% aqueous extract and 293.48±0.00 µmol/g in 100% ethanol extract). Meanwhile, lower total phenolic compounds were detected in the flowers (727.71±11.00 µmol/g in 50% ethanol extract, 603.81±8.46 µmol/g in 100% aqueous extract and 249.29±5.37 µmol/g in 100% ethanol extract) and roots (658.95±5.00 µmol/g in 50% ethanol extract, 450.00±10.76 µmol/g in 100% aqueous extract and 272.28±0.53 µmol/g in 100% ethanol extract). Based on these findings, Pluchea indica has potential medicinal properties that can be further developed to produce neutraceutical products, diet supplements or cosmetic products. However, further research should first be conducted on the effects of these compounds on laboratory animals.
The antiplasmodial activity of the crude extracts of thirty plant species collected from Sabah was evaluated using chloroquine-sensitive strain (D10) and chloroquine-resistant strain (Gombak A) of Plasmodium falciparum. Significant activities were observed for the bark extract of Polyalthia insignis (IC50 3.89 and 11.89 mg/ml against Gombak A and D10, respectively), the leaf extracts of Kopsia dasyrachis (4.62 mg/ml against Gombak A) and Litsea elliptibacea (IC50 8.88 mg/ml against Gombak A), as well as the leaf and bark extracts of Neouvaria acuminatissima (IC50 6.90-10.08 and 0.69 mg/ml against Gombak A and D10, respectively), and the bark extract of Polyalthia microtus(IC50 9.0 and 12.12 mg/ml against Gombak A and D10, respectively).
Respiratory metabolism of the larvae of Malaysian horseshoe crab Tachypleus gigas (Müller) was studied under different salinities, pH, and temperature. The trend in oxygen consumption was uniform at all salinities, ranging from 10-40 ppt, indicating insignificant influence on the oxygen consumption by the larvae. Similarly, the correlation coefficient values showed that the relationship between oxygen consumption and salinity was not significant (P > 0.05; r = 0.245). During the first three hours, the oxygen consumption was 8.89, 10.72, 17.4, and 12.06% at 10, 20, 30, and 40 ppt salinities, respectively. Meanwhile, the maximum oxygen consumption was recorded after 12 hrs, i.e. at salinity 20 ppt. A sudden drop in oxygen consumption was recorded during 3-6 hours of the experiment. This was followed by a gradual increase in the consumption of oxygen up to 12 hours of experiment. A similar trend in the oxygen consumption was observed in different pH levels, ranging from 5 to 9. At pH 6 and 9, during the first six hour, a moderate consumption of oxygen was observed. However, at pH 6, 7 and 8, the rates of oxygen consumption were found to be relatively greater after six hours, indicating unfavourable conditions. The data were statistically tested and it was found that a high degree of correlations existed between pH and oxygen consumption (r = 0.97). The analysis of covariance showed a significant relationship between oxygen consumption and pH (P < 0.05). Meanwhile, minimal variation in oxygen consumption was recorded between 30 and 40oC, with a
gradual decrease in dissolved oxygen concentration up to 12 hours of experimental time. At 50oC,
almost all dissolved oxygen was consumed by the larvae. The rate of oxygen consumption between
30 and 40oC was low during the first 9 hours of the experiment but it was significantly increased at later hours. A sudden increase in the oxygen consumption was recorded at 50oC, suggesting that it
might be the most unfavourable temperature condition. Meanwhile, a significant relationship was
observed between temperature and oxygen consumption (P < 0.05; r = 0.98).
Aluminium (Al) is a low cost, lightweight and corrosion resistant material, which corrodes when exposed to pitting agents. Palm olein exhibits characteristics, which indicate its suitability as a corrosion inhibitor. Tween 20, hexane and diethyl triamine were used as additives to Palm olein to form the inhibitor formulation POT2OHA. The inhibition efficiency (IE) and behaviour of the POT2OHA were determined using potentiodynamic polarization in which Al 6061 samples were immersed in a 1 M HC1 solution at 26, 50 and 70 °C in the presence of different POT2OHA concentrations: 0, 0.03, 0.07, 0.10, 0.13 and 0.17 M The IE increased with increasing POT2OHA concentration, but decreased with increasing temperature. The work presented indicates that POT2OHA is a mixed-type inhibitor capable of inhibiting both corrosive anodic and cathodic reactions. According to the Langmuir isotherm results POT2OHA adsorbs on the A16061 surface through semiphys iosorption and/or semi-chemisorption. The POT2OHA adsorption mechanism on Al 6061 takes through the protonation of micelles by the HC1 solution, whereby protonated micelles in the presence of chloride ions adsorb on both cathodic and anodic surface corrosion sites.
Recently, research and development in the field of drug delivery systems (DDS) facilitating site-specific therapy has reached significant progression. DDS based on polymer micelles, coated micro- and nanoparticles, and various prodrug systems including water-soluble polymer have been prepared and extensively studied as novel drugs designed for cancer chemotherapy and brain delivery. Since polymers are going to be used in human, this study has the interest of testing two types of polymer, polyimides (PI) and polyphenylenevinylene (PPV) on neuronal cells. The objective of this study was to determine the possible neurotoxicity and potential neuroprotective effects of PI and PPV towards SH-SY5Y neuronal cells challenged by hydrogen peroxide (1120) as an oxidant. Cells were pretreated with either PI or PPV for 1 hour followed by incubation for 24 hour with 100 ,uM of 11201. MTS • assay was used to assess cell viability. Results show that PI and PPV are not harmful within the concentration up to 10 pM and 100 pM, respectively. However, PI and PPV do not protect neuronal cells against toxicity induced by H2O, or further up the cell death.
Anion clay hydrotalcite MgA1C0 3 with a Mg/A1 molar ratio of 3:1 was synthesized by co-precipitation at room temperature and pressure. The physicochemical properties were evaluated using Powder X-Ray Diffraction (PXRD), Fourier Transform Infrared (FTIR) spectroscopy and Thermogravimetric Analysis (TGA). The efficacy of anion clay hydrotalcite in the removal ofCcf- from aqueous solutions was investigated with respect to contact time, initial concentration, pH, adsorbent dosage and temperature. The Cd2- removal increased with the increased in contact time, adsorbent dosage, pH and initial concentration. Adsorption decreases with increasing initial concentration and temperature, for which the latter is indicative of an exothermic process. The equilibrium adsorption capacity of MgA1C0 3 was evaluated using linear Langmuir and Freundlich isotherms with respect to the separation factor, RL.
The electrical resistivity and flexural strength of plastic composites reinforced with pineapple leaf particles (PCPLP) is presented. PCPLP were produced using different plastic materials; Polyethylene (PE) and Polypropylene (PP), and different plastic pineapple leaf particle ratios; 50:50 and 70:30. The PCPLP were tested and evaluated with respect to electrical resistivity and flexural strength according to ASTM D257 and D790, respectively. The results indicate that PCPLP made from PP exhibits better electrical resistance than PE, which may be attributed to the better frequency insulation behaviour ofPP. PCPLP using the higher ratio of 70:30 also exhibited better electrical resistance than the lower 50:50 ratio. Cellulose materials inherently influence the electrical resistance of plastic composites, due to their natural propensity to absorb moisture. The PCPLP produced using a ratio of 50:50 for both PP and PE composites exhibited better MOE results than the 70:30 composites, however the converse is true with respect to the MOR. MOE of PCPLP was increased with increasing pineapple leaf particles content due to the greater matrix stiffness of this natural particle with respect to plastic matrix. However, high percentage offiller particles in the matrix (70:30 ratio) has reduced the toughness in the composite structure due to the lost ofphysical contact between high accumulated particles.
MeSH terms: Cellulose; Electricity; Plastics; Polypropylenes; Electric Impedance; Polyethylene; Ananas
Sound is one of the source of energy generated by vibration and is carried through the air in a form of pressure waves (Frederick, 1975). This pressure waves consist of pulsation or vibration of molecules of an elastic medium such as gas, liquid and even solid (Gerber, 1974). Due to its nature, sound can be irritating when it is excessive. The excessive amount of sound is called noise. Exposure to noise is common to the workers working at the industry. This can lead to hearing loss. Hearing loss is one of the most common health problems in the industrialized world. Working activities have been related to noise exposure due to increase use of machine that generates sounds. Many workers throughout the world experience hazardous noise exposure which is ≥ 85 decibels (dB) (Seter, 1998). Based on the previous study in the European region, most of the employers had difficulties to compensate workers diagnosed with hearing loss or hearing impairment cause by the working nature. (Rachiotis et al., 2006). According to European Survey on Working Conditions, about 7% of the workers considered that their work affects their health in the form of hearing disorders. Occupational risk factors for hearing loss include occupational noise, whole body vibration, work-related diseases and exposure to chemical. In this report, we specified in the noise exposure level of the workers.
MeSH terms: Deafness; Industry; Noise, Occupational; Surveys and Questionnaires; Risk Factors; Sound; Vibration; Hearing Loss
This study was done to investigate the background level on microbiological indoor air pollutants in new constructed 8 stories buildings (2 level of Hostel facilities, 3 level of Training Room level, 2 level of Offices and 1 Exhibition Halls and Rooms) in Bandar Baru Bangi, Selangor. The offices and exhibition hall are carpeted furnished. All these spaces were using centralized air conditioning system. Airborne microbes’ concentrations were determined by using a single stage impactor (Biosampler) as per requirement of National Institute of Occupational Safety and Health NIOSH method NIOSH Manual Analytical Method MAM 0800. Mean concentration of total bacteria detected is 1351 CFU/m3 and it was found significantly higher compared to maximum exposure limit 500 CFU/m3 in office room. The mean concentration of total fungi in the office rooms is 479 CFU/m3 and it was found slightly lower compared to maximum exposure limit 500 CFU/m3. The airborne microbe levels were found slightly lower in the accommodation, training and exhibition rooms compared to office room. These findings indicate that although a new constructed building should be having a significant background level of airborne microbe (total bacteria and total fungi).
MeSH terms: Air Conditioning; Air Pollutants; Bacteria; Fungi; National Institute for Occupational Safety and Health (U.S.); United States; Occupational Health; Air Pollution, Indoor
Brush cutting is a commonly performed activity occupationally as well as recreationally in Malaysia. There are various occupational injuries reported related to brush cutting, for example foreign body penetration. There were 11 reported cases of foreign body penetrated in leg of brush cutting workers admitted to orthopaedic ward in Hospital Raja Permaisuri Bainun from the period of January till October 2009. Among the cases, 4 were surgically removed under local anaesthesia and 7 cases performed under general anesthesia. 2 cases reported foreign body penetrated into tibia bone. There were many contributing factors to the injury, which include lack of protective measures for workers, engineering property of brush cutting machine and education on handling of equipment. It is vital to study the factors separately in order to determine and recommend useful preventive measures. However, the actual numbers of cases are under reported and awareness of the problem is undermined.
There is a high prevalence of chronic diseases in the community. Promoting health at the workplace is an effective measure to manage such diseases. This study shares the findings of country-wide company health screening program. The prevalence of high cholesterol among participants was 29 %, high blood pressure was 8% and high blood sugar was 3%. The prevalence of high cholesterol from workplace screening was higher than the community prevalence but the prevalence of high blood pressure and high blood sugar was lower than the community prevalence. The various factors influencing these findings are discussed.
Needle Stick Injury is injuries caused by suture needle and hollow bore needle and does not include injuries via scalpel blades, lancet and glass pieces or by other means for the purpose of this training program. This problem needs to be prevented or minimized by embarking on an effective training program. The applicability of this program will be determined by the response of the participants to the contents and teaching methods which will in future effect the long term out come and the success of the Needle Stick Injury prevention and Universal Precautions training program. This Health Education program was designed to be used for the induction training of new workers as well as those already in service and is applicable to all levels of Health Care Workers especially those directly dealing with or handling syringes and needles. This Needle Stick Injury and Universal Precautions Training Program was carried out in one of the health facility under the Ministry of Health in Sabah and the outcome evaluation and analysis using paired t-test has shown a significant difference in their effectiveness in increasing the knowledge of the Health Care Workers after being exposed to the program (p < 0.01). The process evaluation was able to show that this approach was instrumental in creating awareness among the Health Care Workers who had attended this program. From the study, 98% (49) had not attended any formal training since joining the service, followed by 90% who had given a good overall rating for the program. For the lecture and its relevance, 90% and 74% for the hands–on training. About 77% of the participant was satisfied with the discussion. The program can be developed further and with it a comprehensive training module can be produced. The long-term benefits of such a training program will need to be evaluated in a future study.
MeSH terms: Health Education; Health Facilities; Health Personnel; Health Promotion; Malaysia; Needles; Sutures; Syringes; Needlestick Injuries; Universal Precautions
A preliminary study has been conducted in a new constructed 8 stories building (2 level of Hostels facility, 3 level of Training Room, 2 Level of Offices and 1 level of Exhibition Halls and Rooms) in Bandar Baru Bangi, Selangor. The Hostels facility is a floor tile and furnished with build in locker and use split air conditioning system while the Training Room and Exhibition Rooms used floor tile. The Offices and Exhibition Hall are carpeted furnished. All these spaces were using centralized air conditioning systems. A pre-commissioning assessment on 5 chemical parameters of indoor air pollutants such Total Volatile Organic Compounds (TVOC), Formaldehyde, Respirable Particulates (PM!
MeSH terms: Air Conditioning; Air Pollutants; Formaldehyde; Respiration; Air Pollution, Indoor; Cell Respiration; Volatile Organic Compounds
The research is focus generally to identify and investigate the issue of accessible design for wheelchair users on selected Keretapi Tanah Melayu Berhad (KTM) commuter stations in the city of Kuala Lumpur. The objectives are to ensure that the design of accessibility is comply with the law, regulations, standard requirements and guidelines; to understand the recent condition and their needs in commuter stations and to allow their secure equal rights and opportunities as others. The research began by gaining reliable information through literature study and a checklist for building audit was prepared to evaluate the accessibility. A building access survey was carried out on selected stations which enclosed three main stages to show the pattern of passengers’ path. Stage 1: From the road to the ticket counter. Stage 2: From the ticket counter to the platform. Stage 3: From the platform to the train. A series of structured questionnaire was also constructed to study and get a feedback from selected target of users. Result of findings in this study had been analyzed to assist the management and the station concerned in upgrading their station facilities to a comfortable, accessible, friendly and safe environment in order to encourage more users, including disabled persons to benefit from it.
MeSH terms: Disabled Persons; Human Rights; Publications; Surveys and Questionnaires; Transportation; Wheelchairs; Checklist
Societal dynamics and increased public demands on education have produced adverse stressful classroom situation that have led to increase emotional and physical disabilities among teacher. The main objective of this descriptive study was to identify the causes of occupational stress amongst secondary school teachers. This study also conducted in order to determine the suitable ways and strategies at helping teachers to cope with the work related pressures that have increased during the past decade. The samples of this study were 100 teachers from four secondary schools in Dungun District, Terengganu. The data were descriptively analyzed based on the responds on a set of questionnaires, checklist and 20 interview sessions conducted for exploration of coping strategy with 20 out of 100 teachers. Based on the finding, it can be concluded that interpersonal relations, physical conditions and job interest contribute towards workrelated stress among teachers. Also discussed the 10 most frequently used coping strategies by teachers. Therefore, there are suggesting measures, which teachers may take to help them cope more effectively with potentially stressful situations at school.
MeSH terms: Adaptation, Psychological; Humans; Interpersonal Relations; Malaysia; Surveys and Questionnaires; Schools; Stress, Psychological*; School Teachers
Individual factors have been considered to be a key issue to organizations’ performance and survival. Specifically, previous studies provide evidence that individual factors are closely associated with accidents in the workplace. Therefore, this study seeks to investigate the relationship between individual factors and workplace safety. 50 respondents have been randomly chosen from a manufacturing company in Johor Bahru, Malaysia. Data are collected using a survey and are analyzed using SPSS version 16.0. A descriptive statistic, cross tabulation, independent sample t-test and one-way between groups ANOVA are employed to interpret findings of the study. Findings show that employees’ perception on safety performance is at high level (Mean= 115, Standard Deviation= 17.73). Furthermore, the results of cross tabulation demonstrate that individual factors play a key role to determine the organization safety performance level. Another significant finding reveals that there is a significant difference of safety performance mean to two of individual factors namely gender and tenure of service. Individual factors namely gender, age, tenure of service and academic qualification give a significant impact to employees’ perception on safety performance.
MeSH terms: Accidents; Analysis of Variance; Employment; Malaysia; Surveys and Questionnaires; Safety; Workplace
Disaster can strike at any time on a small or large scale, but if an institution is prepared, the damage may be reduced or avoided. A disaster is a serious disruption of the functioning of a society, causing widespread human, material, or environmental losses which exceed the ability of affected society to cope using only its own resources. Disasters are often classified according to their speed of onset (sudden or ‘slow burning’), or according to their cause (natural or man-made). There is no single and specific method in handling a disaster. The application and method of disaster management do not only depend on types, location and levels of disaster, but also depend on the effectiveness and good system of management as well as the total commitment of first responders and disaster managers involved in handling a disaster. National Security Council Directive No. 20 is both a proactive and reactive generic plan to manage disasters in Malaysia. It is an integrated disaster management plan in mitigation, preparedness, response and recovery.