The hydrochloride, sulphate and ethylcarbonate salts of quinine were given in single oral doses (600 mg base equivalent) to nine healthy male subjects according to a cross-over design. No statistically significant differences were noted in the plasma drug concentration-time profiles although inter- and intra-subject variation in AUC, Cmax and tmax values was appreciable. The ethylcarbonate salt may be preferred for use in paediatric patients because of its neutral taste.
Poly(hydroxamic acid) ion exchange resin was evaluated for speciation of iron(II) and iron(III) ions. Distribution coefficients indicate that the resin is more selective towards iron(III) ion. Column extractions show that iron(III) ion is quantatively extracted from sulfuric acid solutions at concentrations of between 0.01 to 0.00lM but only 2% or less of iron(II) ion is retained under these conditions. Further studies show that these two ions can be separated and their separations are not affected by the presence of nickel, zinc, copper, calcium, chloride, bromide, nitrate and sulphate.
Resin penukar ion poli(asid hidroksamik) telah dikaji untuk penspesiesan ion-ionferum. Pekali taburan menunjukkan resin ini mempunyai kepilihan yang tinggi terhadap ion ferik berbanding dengan ionferus. Pengekstrakan dengan kaedah turus mendapati ion ferik dari larutan asid sulfurik 0.01 dan 0.00lM boleh diesktrak secara kuantitatif manakala pengekstrakan ion ferus hanya 2% atau lebih kecil. Kajian lanjut menunjukkan resin ini boleh memisahkan ion ferik dari ion ferus dan pemisahan ini tidak diganggu oleh kehadiran ion-ion nikel, zink, kuprum, kalsium, klorida, bromida, nitrat dan sulfat.
Treatment of vanadium(V) oxide with an ethanol-concentrated sulfuric acid mixture, followed by the addition of an equimolar amount of beta-alanine and sodium hydroxide, and finally raising the pH to 3.9 with sodium carbonate solution, under continuous heating in a water bath and in the presence of air, leads to the polyionic sodium cyclo-[mu(6)-(sulfato-O,O',O'')tris[mu-(beta-alanine-O,O')-mu-oxo]tris(mu-hydroxo-mu-oxo)hexa[oxovanadium(V)]] sulfate tridecahydrate which crystallizes in the monoclinic P2(1)/n space group [a = 9.5192(4), b = 20.1185(9), c = 22.6174(9) A, beta = 97.011(1) degrees; Z = 4]. The crown-shaped polyoxovanadium(V) cluster cation, with carboxylate-bridging amino acid ligands, has an Anderson structure with two unique capping sulfato ligands. Its structural analysis, together with IR, UV-vis, and preliminary data on its solution properties, is presented.
In this work, we studied whether chondroitin sulfates and dextran sulfates (DXSs) can influence hypochlorite-induced peroxidation of phosphatidylcholine (PC) liposomes. Multilamellar liposomes (2 mg lipid/ml) were prepared in phosphate buffer, pH 7.4, with NaCl or not and exposed to reagent HOCl/ClO- (1mM) at 37 degrees C in the presence of different concentrations of chondroitin 6-sulfate (C6S), chondroitin 4-sulfate (C4S), DXS 8000, DXS 40,000, and DXS 500,000. Lipid peroxidation was assessed by thiobarbituric acid-reactive substance (TBARS) production. DXSs and C6S enhanced TBARS production in a dose-dependent manner. The decline in TBARS production at the relatively high C6S concentrations may be attributed to C4S present in C6S, since in contrast to C6S, C4S is known to react with hypochlorite. Dextrans, nonsulfated analogues of DXS, failed to modulate TBARS production. This fact indicates the important role of negatively charged sulfate groups for DXS to facilitate hypochlorite-induced peroxidation of PC liposomes. The electrostatic nature of the mechanism providing for the pro-oxidative effect of DXS was also supported by the influence of liposome surface charge and solution ionic strength on the extent of liposome peroxidation. The addition of calcium ions to the incubation mixture did not prevent the pro-oxidative action of DXS. The relevance of the results to atherogenesis is discussed.
Polymer electrolytes based on poly(ethylene oxide)-lithium triflate (PEO-LiCF3SO3) and poly(ethylene oxide)-lithium sulphate (PEO-Li2S4) were prepared by using solution casting method. Measurements of conductivity and dielectric were carried out on these films as a function of frequency at various temperatures. It was observed that PEO-LiCF3SO3 polymer electrolytes have higher conductivity. The interaction between PEO and Li salts were studied by Fourier transform infrared (FTIR).
We present our two year experience with a dermal regeneration template (INTEGRA) in burn reconstructive surgery for contracture release as well as a reconstructive tool for management of soft tissue loss.
The treatment of major burn injuries are a formidable challenge to the burn surgeon. Early aggressive surgery for deep to full thickness burn injuries is vital in the prevention of infection. The ultimate goal in major burn injuries is to prevent the onset of multi-resistant organisms and achieve early wound cover. The field of tissue engineering can help to expedite the healing of these burn wounds. The development of keratinocyte culture delivery system can be used clinically to fasten the healing process and save many lives.
Corrosion caused by sulphate-reducing bacteria (SRB) isolated from seawater nearby to Pasir Gudang has been studied. The test coupon was a AISI 304 stainless steel. Potential and corrosion rate measurements were carried out in various types of culturing solutions, with SRB1, SRB2, combination of SRB1 & SRB2 and without SRBs inoculated (sterilized). From Tafel plots a higher corrosion rate has been found in medium inoculated with SRBs than that of the sterilized medium (control). When SRBs were present in the medium, the Tafel plot shifted towards more negative values (Ecorr was shifted to much less anodic values) and increase in current density compared to that of the sterilized medium (control). Localized corrosion was observed on the metal surface, and it was associated to the SRB activity. X-ray analysis (EDAX) showed that the corrosion product has higher content of sulphur for medium containing SRBs than that of the sterilized medium. X-Ray Diffraction analysis carried out on corrosion products which showed the presence of iron sulphide. This indicates the influence of the presence of SRB in corrosion process.
The aim of this study was to determine the surface chemistry during biocorrosion process on growth and on the production of exopolymeric substances (EPS) in batch cultures of mix-strains of marine sulphate-reducing bacteria (SRB) isolated from Malaysian Shipyard and Engineering Harbours, Pasir Gudang. The EPS and precipitates were analyzed by x-ray photoelectron spectroscopy (XPS). The XPS results indicate that Fe(2p3/2) spectrum for iron sulphide can be fitted with Fe(II) and Fe(III) components, both corresponding to Fe-S bond types. The absence of oxide oxygen in the O(1s) spectrum and Fe(III)-O bond types in the Fe(2p3/2) spectrum supports the conclusion that iron sulphides are composed of both ferric and ferrous iron coordinated with monosulphide and disulphide.
The corrosion potential of AISI 304 stainless steel coupons influenced by sulphate-reducing bacteria (SRB) has been studied. Pure colony of SRB was isolated from the Malaysia Marine and Heavy Engineering, Pasir Gudang, Johor. Open circuit potential measurements were carried out in variable types of culturing solutions with SRB1, SRB2, combination of SRB1 & SRB2 and without SRBs inoculated. Results showed that the corrosion potential, Eoc increased in the presence of SRBs (in pure and mixed culture) compared to that of control. EDS analysis showed the strong peak of sulphur in coupon containing SRB cultures compared to the control. ESEM data showed that the high density cell of SRBs were associated with corroding sections of surface steel comparing with non-corroding sections for coupons immersed in VMNI medium containing SRBs.
Strategies to control outbreaks of influenza, a contagious respiratory tract disease, are focused mainly on prophylactic vaccinations in conjunction with antiviral medications. Currently, several mammalian cell culture-based influenza vaccine production processes are being established, such as the technologies introduced by Novartis Behring (Optaflu) or Baxter International Inc. (Celvapan). Downstream processing of influenza virus vaccines from cell culture supernatant can be performed by adsorbing virions onto sulfated column chromatography beads, such as Cellufine sulfate. This study focused on the development of a sulfated cellulose membrane (SCM) chromatography unit operation to capture cell culture-derived influenza viruses. The advantages of the novel method were demonstrated for the Madin Darby canine kidney (MDCK) cell-derived influenza virus A/Puerto Rico/8/34 (H1N1). Furthermore, the SCM-adsorbers were compared directly to column-based Cellufine sulfate and commercially available cation-exchange membrane adsorbers. Sulfated cellulose membrane adsorbers showed high viral product recoveries. In addition, the SCM-capture step resulted in a higher reduction of dsDNA compared to the tested cation-exchange membrane adsorbers. The productivity of the SCM-based unit operation could be significantly improved by a 30-fold increase in volumetric flow rate during adsorption compared to the bead-based capture method. The higher flow rate even further reduced the level of contaminating dsDNA by about twofold. The reproducibility and general applicability of the developed unit operation were demonstrated for two further MDCK cell-derived influenza virus strains: A/Wisconsin/67/2005 (H3N2) and B/Malaysia/2506/2004. Overall, SCM-adsorbers represent a powerful and economically favorable alternative for influenza virus capture over conventional methods using Cellufine sulfate.
This study investigated the electrochemical oxidation of stabilized leachate from Pulau Burung semi-aerobic sanitary landfill by conducting laboratory experiments with sodium sulfate Na(2)SO(4) (as electrolyte) and graphite carbon electrodes. The control parameters were influent COD, current density and reaction time, while the responses were BOD removal, COD removal, BOD:COD ratio, color and pH. Na(2)SO(4) concentration was 1 g/L. Experiments were conducted based on a three-level factorial design and response surface methodology (RSM) was used to analyze the results. The optimum conditions were obtained as 1414 mg/L influent COD concentration, 79.9 mA/cm(2) current density and 4 h reaction time. This resulted in 70% BOD removal, 68% COD removal, 84% color removal, 0.04 BOD/COD ratio and 9.1 pH. Electrochemical treatment using graphite carbon electrode was found to be effective in BOD, COD and color removal but was not effective in increasing the BOD/COD ratio or enhancing biodegradability of the leachate. The color intensity of the treated samples increased at low influent COD and high current density due to corrosion of electrode material.
New solid acid catalyst consisting of zirconium sulfate (ZS) supported on a pure-HMS hexagonal mesoporous material (HMS) have been prepared and characterized. This heterogeneous catalyst is able to make a contribution to the field of acid catalyst involving bulky organic molecules. XRD analysis shows that ZS is intact after impregnated on HMS surface and formed finely dispersed species. No ZS crystal phase was developed even at ZS loadings as high as 40 wt %. The occurrence of chemical interaction between ZS and HMS was observed by XPS analysis. Further, XRF results demonstrated that there is no leaching of ZS elements after impregnation. This study shows that ZS can be impregnated on HMS and would be a promising solid acid catalyst for acid-type reactions espcially invovling bulky organic molecuels.
A co-deposition of nickel-phosphorus-alumina (NiPA) composite coatings were obtained from an ordinary sulphate-based plating bath consisting of 5 g/l alumina (Al2O3) particles. The particles were dispersed by using mechanical agitation at 125 rpm. The presence of Ni3P and Al2O3 phases in the coatings was confirmed by XRD analysis. SEM/EDX results indicated that a smooth Ni3P coating was obtained and Al2O3 particles were embedded into the coating. Microscopic observation showed that the bonding between the Ni3P metal matrix and the Al2O3 ceramic particles was compact.
Sulphate-reducing bacteria (SRB), implicated in microbiologically influenced corrosion were isolated from the deep subsurface at the vicinity of Pasir Gudang, Johor, Malaysia. Electrochemical impedance spectroscopic (EIS) study was carried out to determine the polarization resistance in various types of culturing solutions, with SRB1, SRB2, combination of SRB1 and SRB2 and without SRBs inoculated (control). EIS results showed that in the presence of SRB1, SRB2 and mixed culture SRB1 and SRB2, polarisation resistance values were 7170, 6370 and 7190 ohms respectively compared to that of control, 92400 ohm. X-ray analysis (EDS) of the specimens indicated high sulphur content in the medium containing SRBs. Localized corrosion was observed on the metal surface which was associated with the SRB activity.
Binding constants for the enantiomers of modafinil with the negatively charged chiral selector sulfated-β-CD (S-β-CD) using CE technique is presented. The calculations of the binding constants employing three different linearization plots (double reciprocal, X-reciprocal and Y-reciprocal) were performed from the electrophoretic mobility values of modafinil enantiomers at different concentrations of S-β-CD in the BGE. The highest inclusion affinity of the modafinil enantiomers were observed for the S-enantiomer-S-β-CD complex, in agreement with the computational calculations performed previously. Binding constants for each enantiomer-S-β-CD complex at different temperatures, as well as thermodynamic parameters for binding, were calculated. Host-guest binding constants using the double reciprocal fit showed better linearity (r(2)>0.99) at all temperatures studied (15-30°C) and compared with the other two fit methods. The linear van't Hoff (15-30°C) plot obtained indicated that the thermodynamic parameters of complexation were temperature dependent for the enantiomers.
Redox polymerization of acrylonitrile (AN) with ethyl acrylate (EA) and fumaronitrile (FN), as comonomer and termonomer respectively, were carried out using sodium bisulfite (SBS) and potassium persulphate (KPS) as initiators at 40°C. The actual composition of monomers in copolymers and terpolymers has been characterized by gas chromatography (GC). The effects of EA and FN on the glass transition temperature (Tg) and stabilization temperature have been studied by Differential Scanning Calorimetry (DSC). The degradation behaviour and char yield were obtained by thermogravimetric analysis. Meanwhile, incorporation of 10 mol% of EA in homoPAN system was found to greatly reduce Tg to 66°C as compared to that of the homoPAN (Tg=105°C). The initial cyclization temperature (Ti) was found to be higher (264°C) in comparison to that of homoPAN (246°C). In addition, the incorporation of EA was also shown to reduce the char yield of copolymer to 40%. When FN was incorporated as termonomer, the char yield of poly(AN/EA/ FN) 90/4/6 increased up to 44% after the heat treatment with the lowest Ti (241°C).
The present study aimed to provide an insight of C. jejuni ATCC 33560 phenotype profiles (carbon sources and sensitivity to osmolytes and pH) using Phenotypic MicroArray (PM) system in response to optimal and suboptimal temperature. C. jejuni ATCC 33560 showed utilization carbon sources from amino acids and carboxylates but not from sugars. C. jejuni ATCC 33560 is sensitive to NaCl at 2% and above but showed survival in a wide range of food preservatives (sodium lactate, sodium phosphate, sodium benzoate, ammonium sulphate and sodium nitrate). When incubated at suboptimal temperature, no phenotype loss was observed in carbon source plates. Phenotype loss of C. jejuni ATCC 33560 was observed in sodium chloride (1%), sodium sulphate (2-3%), sodium formate (1%), sodium lactate (7-12%), sodium phosphate pH7 (100mM and 200mM), ammonium sulphate pH8 (50mM), sodium nitrate (60mM, 80mM and 100mM), sodium nitrite (10mM), and growth in pH5. The phenotypic profile from present study will provide a better insight related to survival of C. jejuni ATCC 33560.
This study reports the conversion of Jatrophacurcas L. oil to biodiesel catalyzed by sulfated zirconia loaded on alumina catalyst using response surface methodology (RSM), specifically to study the effect of interaction between process variables on the yield of biodiesel. The transesterification process variables studied were reaction temperature, reaction duration, molar ratio of methanol to oil and catalyst loading. Results from this study revealed that individual as well as interaction between variables significantly affect the yield of biodiesel. With this information, it was found that 4h of reaction at 150°C, methanol to oil molar ratio of 9.88 mol/mol and 7.61 wt.% for catalyst loading gave an optimum biodiesel yield of 90.32 wt.%. The fuel properties of Jatropha biodiesel were characterized and it indeed met the specification for biodiesel according to ASTM D6751.
The effects of Glucosamine Sulphate (GS) and Chondroitin Sulphate (CS) on the healing of damaged and repaired articular cartilage were investigated. This study was conducted using 18 New Zealand white rabbits as experimental models. Focal cartilage defects, surgically created in the medial femoral condyle, were either treated by means of autologous chondrocyte implantation (ACI) or left untreated as controls. Rabbits were then divided into groups which received either GS+/-CS or no pharmacotherapy. Three rabbits from each group were sacrificed at 12 and 24 weeks post-surgery. Knees dissected from rabbits were then evaluated using gross quantification of repair tissue, glycosaminoglycan (GAG) assays, immunoassays and histological assessments. It was observed that, in contrast to untreated sites, surfaces of the ACI-repaired sites appeared smooth and continuous with the surrounding native cartilage. Histological examination demonstrated a typical hyaline cartilage structure; with proteoglycans, type II collagen and GAGs being highly expressed in repair areas. The improved regeneration of these repair sites was also noted to be significant over time (6 months vs. 3 months) and in GS and GS+CS groups compared to the untreated (without pharmacotherapy) group. Combination of ACI and pharmacotherapy (with glucosamine sulphate alone/ or with chondroitin sulphate) may prove beneficial for healing of damaged cartilage, particularly in relation to focal cartilage defects.