Displaying all 14 publications

Abstract:
Sort:
  1. Syahrul, A.S., Jaafar, M.S., Al-Halemi, Ahmed, Hamouda, S.A.
    MyJurnal
    The purpose of this study is to measure and monitor the radon concentration from fabricated foamed light concrete, made of Portland cement, mine sand and granite. The concentration of radon released was measured using Radon Monitor Model 1027 from Sun Nuclear. The results of this research showed that the avearge radon concentration from foamed light concrete was 2.2 pCiL-1 L. Higher radon concentrations were detected after three days of measurements. Environment Protection Agency stated in its guidelines that radon concentration must lower than 4 pCiL-1 for a healthy environment. Thus, the use of foamed light concrete can be one of the alternatives to reduce radon concentration levels in human environment.
    Matched MeSH terms: United States Environmental Protection Agency
  2. Mah, D.Y.S., Lau, J.T.
    MyJurnal
    Urbanisation increases the level of imperviousness in a catchment, and more runoff is converted from rainfall in urban areas. To mitigate this adverse situation, dispensed green infrastructure presents the best solution for delivering results in reducing stormwater impact. Green roofs and rain gardens are extensively studied and widely available in the literature, but this is not the case for green walls, which more often than not, are treated as ornaments. Thus, this study developed a computer-aided stormwater model that incorporates a green wall to investigate its effectiveness as an urban drainage system. The effectiveness of employing a green wall as a stormwater component is tested using USEPA SWMM 5.1 and the embedded bioretention cell interface. Four simulation models according to different conditions and precipitation input are tested, compared and discussed. The conditions include investigation of different soil types, average recurrence interval (ARI) and storm duration with design and observed rainfall. The results reveal that synthesis precipitation data, used in Scenario 1, 2 and 3, decreased runoff by more than half, at 55% on condition of one-year ARI and 5 minutes of storm duration. Meanwhile, Scenario 4 also shows a repetition of runoff reduction by half after the integration of the green wall using the observed rainfall data. Thus, it is verified that a green wall can be effectively used as an urban drainage system in reducing surface runoff.
    Matched MeSH terms: United States Environmental Protection Agency
  3. Ahmed, Al-Halemi, Jaafar, M.S.
    MyJurnal
    Radon-222 emanation from selected locally produced samples of building materials, used in Malaysia were measured using the Professional Continuous Radon Monitor Model 1027, which is a patented electronic detecting-junction photodiode sensor to measure the concentration of radon gas. Each sample was placed for 72 hours inside a 3.11 x 10 -2 m 3 sealed container. It was found that the average radon concentration Bqm -3 of air for concrete bricks, concrete brick with cemented coatings, concrete brick with cemented coatings and paint samples were, 303.7 Bq/m 3, 436.6 Bqm -3, and 410.7 Bqm -3, respectively. (Bqm -3 ) for brown clay brick, brown clay brick with cemented coatings, brown clay brick with cemented coatings and paint were 166.5 Bqm -3, 166.5 Bqm -3, and 148 Bqm -3, respectively. (Bqm -3 ) for sample of compact ceramic tile was 0 Bqm -3. The findings show that concrete brick samples are important source of radon emanation, while brown clay brick have been accepted as the recommendation of the U.S. Environmental Protection Agency (EPA), and ceramic tiles had no emanation of radon gas due to their compact surface, or the glazed layer created on the tile surface during the manufacturing process, which blocks radon emanation. A positive correlation between radon emanation and radium content has been observed for both brown clay brick and concrete brick samples whereas a negative correlation for ceramic tile has been observed. Consequently from the findings, in order to reduce radon emanation and radon exposure in house dwellings and in addition to EPA recommendation of sealed cracks and established good ventilation, we recommend concrete walls to be painted and concrete floors to be paved with ceramic tiles.
    Matched MeSH terms: United States Environmental Protection Agency
  4. Ahmad Saat, Zaini Hamzah, Zaharidah Abu Bakar, Zuraidah A. Munir, Siti Mariam Sumari, Misbah Hassan
    MyJurnal
    A study was carried out to determine short term diurnal radon concentration at five locations in Malaysia. Two locations (KG & AP) are former tin mining areas that has been converted to housing area and training centre respectively, one a relatively new city (SA), that was formerly a rubber and oil palm plantation area, one older cities (KB) and one housing complex by the sea (LP). The study was carried out in 2005, 2006 and 2007 using a diffused-junction photodiode sensor continuous radon monitor. The monitor is recognized by the USEPA. In each location, measurements were carried out on at least ten sites. Former tin mining areas of KG and AP shows up to seven times higher indoor average than the average in the other three locations. However the indoor average in all locations is still below the action level of 4 pCiL-1. For outdoor, the former tin mining areas average concentration was higher than the global average of 0.4 pCiL-1. For the twenty four hours temporal variation the trend indicated that former tin mining areas concentration are always higher, and at time up to six fold higher. The hourly variation of all locations follows an identical trend of high concentration during early to late morning and drop in the afternoon till evening. The outdoor twenty four hour temporal average of former tin mining areas is consistently higher than the outdoor global average of 0.4 pCiL-1. The strong correlation between indoor and outdoor concentration at AP, indicates that indoor radon might originates from outdoor environment. The study was also extended to estimate the effective dose (mSvyr-1) of Rn-222 to the public.
    Matched MeSH terms: United States Environmental Protection Agency
  5. Mohammad Razaul Karim, Sumiani Yusoff, Hashim Abdul Razak, Faisal I. Chowdhury, Hossain Zabed
    Sains Malaysiana, 2018;47:523-530.
    Technical benefit of incorporation of Palm Oil Clinker (POC) in cement-based applications has been proven in recent
    studies. The aim of this work was to assess the heavy metal leaching behavior to ensure environmental safety of using
    POC in cement-based applications. The chemical composition, morphology, total organic carbon (TOC) and mineralogy
    were determined using XRF, FESEM, TOC analyzers and XRD to select appropriate chemical reagents for complete digestion.
    HNO3
    , HF and HClO4
    were used for digestion of POC to measure heavy metal content using ICP-MS. The chemical reagents
    CH3
    COOH, NH2
    OH-HCl, H2
    O2
    +CH3
    COONH4
    and HF+HNO3
    +HCl were used for extraction of acid soluble, reducible,
    oxidizable and residual fractions of heavy metals in POC, respectively. The leaching toxicity of the POC was investigated
    by the USEPA 1311 TCLP method. The result showed the presence of Be, V, Cr, Ni, Cu, Zn, As, Se, Ag, Cd, Ba and Pb with
    levels of 5.13, 11.02, 2.65, 1.93, 45.43, 11.84, 15.07, 0, 0, 81.97 and 1.76 mg/kg, respectively, in POC. The leaching value
    in mg/L of As (4.56), Cu(1.05), Be (0.89), Zn(0.51), Ba(0.26), Ni (0.17), V(0.15), Cr(0.001) and Se (0.001) is found well
    below the standard limit of risk. Risk assessment code (RAC) analysis confirms the safe incorporation of POC in cementbased
    applications.
    Matched MeSH terms: United States Environmental Protection Agency
  6. Ng HW, Doughty SW, Luo H, Ye H, Ge W, Tong W, et al.
    Chem Res Toxicol, 2015 Dec 21;28(12):2343-51.
    PMID: 26524122 DOI: 10.1021/acs.chemrestox.5b00358
    Some chemicals in the environment possess the potential to interact with the endocrine system in the human body. Multiple receptors are involved in the endocrine system; estrogen receptor α (ERα) plays very important roles in endocrine activity and is the most studied receptor. Understanding and predicting estrogenic activity of chemicals facilitates the evaluation of their endocrine activity. Hence, we have developed a decision forest classification model to predict chemical binding to ERα using a large training data set of 3308 chemicals obtained from the U.S. Food and Drug Administration's Estrogenic Activity Database. We tested the model using cross validations and external data sets of 1641 chemicals obtained from the U.S. Environmental Protection Agency's ToxCast project. The model showed good performance in both internal (92% accuracy) and external validations (∼ 70-89% relative balanced accuracies), where the latter involved the validations of the model across different ER pathway-related assays in ToxCast. The important features that contribute to the prediction ability of the model were identified through informative descriptor analysis and were related to current knowledge of ER binding. Prediction confidence analysis revealed that the model had both high prediction confidence and accuracy for most predicted chemicals. The results demonstrated that the model constructed based on the large training data set is more accurate and robust for predicting ER binding of chemicals than the published models that have been developed using much smaller data sets. The model could be useful for the evaluation of ERα-mediated endocrine activity potential of environmental chemicals.
    Matched MeSH terms: United States Environmental Protection Agency
  7. Yap CK, Cheng WH, Karami A, Ismail A
    Sci Total Environ, 2016 May 15;553:285-96.
    PMID: 26925739 DOI: 10.1016/j.scitotenv.2016.02.092
    A total of 40 marine mussel Perna viridis populations collected (2002-2009) from 20 geographical sites located in two busy shipping lanes namely the Straits of Malacca (10 sites; 16 populations) and the Straits of Johore (8 sites; 21 populations) and three populations (2 sites) on the east coast of Peninsular Malaysia, was determined for Cd, Cu, Fe, Ni, Pb and Zn concentrations. In comparison with the maximum permissible limits (MPLs) set by existing food safety guidelines, all metal concentrations found in all the mussel populations were lower than the prescribed MPLs. In terms of the provisional tolerable weekly intake prescribed by the Joint FAO/WHO Expert Committee on Food Additives (JECFA) and oral reference doses (ORDs) by the USEPA, all the studied metals (except for Pb) were unlikely to become the limiting factors or unlikely to pose a risk for the consumption of the mussel populations. The estimated daily intake (EDI) for average level mussel (ALM) and high level mussel (HLM) consumers of mussels was found to be lower than the ORD guidelines for Cd, Cu, Fe, Ni and Zn. Furthermore, the target hazard quotient (THQ) was found to be less than 1 for ALM consumers but higher than 1 for HLM consumers in some sites. Therefore, there were no potential human health risks to the ALM consumers of the mussels. However, for Pb THQ values, the Pb levels in some mussel populations could create a health risk problem. Present results indicate that the consumption amounts of mussels should be limited for minimizing potential health risks of heavy metals to the HLM consumers.
    Matched MeSH terms: United States Environmental Protection Agency
  8. Sa’adiah Shahabudin, Rohayu Hami, Lim, Lee-Sim, Amalina Salleh
    MyJurnal
    The aim of this study to assess the efficiency of flushing
    method of Dental Unit Waterline (DUWL) system in reducing the
    number of microorganism. Water samples were taken before and after
    two minutes of flushing from air-water syringes system in ten randomly
    selected dental units in a Dental Teaching Centre. These samples
    were immediately transferred to the microbiology laboratory in the cool
    box within 8 hours for the heterotrophic plate count (HPC) test. Paired
    t-test was used to analyse number of microbe before and after flushing.
    The numbers of colony forming unit (CFU) ranged from 13,000 to
    120,000CFU/ml in unflushed samples, and 3,000 to 15,000CFU/ml in
    flushed samples. The mean HPC post-flushing was lower than preflushing [8360.00 (4561.48) vs 63300.00 (44587.12) CFU/ml]. The
    mean HPC between pre- and post-flushing was significantly different
    (P=0.004, 95% CI 22039.52, 87840.48). The coliform count from the
    control was 140 CFU/ml. In conclusion, flushing method of DUWL
    system significantly reduces the number of microorganisms in the
    dental unit. However, the level of microorganisms still does not meet
    the standard guideline by Environmental Protection Agency for safe
    drinking water, which should be below 500 CFU/ml. In our opinion, the
    duration of flushing should be increased and additional chemical
    treatments of the dental units should be implemented to ensure the
    safety of patients and dental personnel.
    Matched MeSH terms: United States Environmental Protection Agency
  9. Beddu S, Abd Manan TSB, Zainoodin MM, Khan T, Wan Mohtar WHM, Nurika O, et al.
    Data Brief, 2020 Aug;31:105843.
    PMID: 32596432 DOI: 10.1016/j.dib.2020.105843
    Coal combustion by-products (CCPs) (i.e. fly (FA) and bottom (BA) ashes) generated by power plants contain heavy metals. This research presents leaching properties of coal ashes (FA and BA) collected from Jimah coal-fired power station, Port Dickson, Negeri Sembilan using USEPA standard methods namely toxicity characteristic leaching procedure (TCLP), and synthetic precipitation leaching procedure (SPLP). Heavy metals like lead (Pb), zinc (Zn), copper (Cu) and arsenic (As) were quantified using atomic absorption spectrometer (AAS). The leached of heavy metals fluxes were Cu < Zn < Pb < As. As leached the most whilst indicating of possible contamination from As. Overall, the ranges of leached concentration were adhered to permissible limits of hazardous waste criteria for metal (Pb and As) and industrial effluent (Zn and Cu). The presented data has potential reuse as reference for the coal ash concrete mixed design application in construction industries.
    Matched MeSH terms: United States Environmental Protection Agency
  10. Ahmad Saat, Nor Shazlina Zainal, Zaini Hamzah
    MyJurnal
    Ground water contain natural radioactivity associated with uranium and thorium that present naturally in rocks and soils. Humans may be exposed to the emission of energetic alpha particle from supported radon decaying process in this water when it is inhaled or ingested. Assessment of supported radon in ground water was carried out using fourteen ground water samples from Cameron Highlands. The measurement was accomplished by degassing the water samples using pump and then allowing the gas to flow into specially constructed 0.0191 m8 metal chamber. The activity concentration of supported radon in water sample was measured using continuous radon monitor inside the radon chamber. Measurement was carried out at one hour interval for twenty four hours. The hourly supported radon concentration was found to stabilize after about 8 hours. The stabilized concentration was used to determine supported radon activity concentration in the water samples. Results of the study show that depending on the sampling location, the activity concentrations of supported radon are in the range from 0.09 - 0.48 Bq/L which is lower than the activity concentration of radon in drinking water as proposed by USEPA (11 Bq/L).
    Matched MeSH terms: United States Environmental Protection Agency
  11. Mohd Hasni Jaafar
    MyJurnal
    Dioxins are a most toxic compound ever studied by human until today. Their significant health effects involved all ranges of age, including infants due to exposure to contaminated breast milk. The objective of the study was to appraise the status of dioxin contamination in breast milk among postnatal mothers live in urban and suburban areas in Klang Valley. It was conducted as a cross sectional study involving 101 postnatal mothers who came for their infant second hepatitis B vaccination. The samples were analysed using High Resolution Gas Chromatography (HRGC) following the USEPA Method 8290. About 70.3% of the samples were found detected with dioxin congeners. More suburban mothers have positive breast milk dioxins compared to urban mothers, 100.0% and 67.0% respectively. Significant associated factors include high fat daily intake (p=0.013), high milk daily intake (p= 0.044), high meat daily intake (p=0.001), body mass index more than 30 kg/m2 (p=0.005), and body fat % of more than 26% (p=0.046). In conclusion, amount daily intake of fat diet, meat, milk, body mass index and body fat are significant associated factors for the present of dioxins in breast milk among postnatal mothers in Klang Valley. More suburban mothers contain dioxins in their breast milk, which poses higher risk of health problems among their infants. A comprehensive study need to be conducted and regular followup need to be established in monitoring the future severity of maternal breast milk contamination to ensure the health of the next generations.
    Matched MeSH terms: United States Environmental Protection Agency
  12. Dora Esphylin, Sharifah Norkhadijah Syed Ismail, Sarva Mangala Praveena, Zailina Hashim, Emilia Zainal Abidin
    MyJurnal
    Background: Prolonged exposure of heavy metals in the respirable particulate matter (PM10) from municipal solid waste (MSW) landfills may affect children health. Objective: To investigate the association of reported respiratory symptom with heavy metals in PM10, with heavy metals in fingernails among children residing close to MSW landfills. Methods: Two groups of children age 7 to 12 years old were involved in this cross-sectional study. Those residing within 3 km radius from a landfill were the exposed group and those residing more than 3 km radius as the unexposed group. Questionnaires adapted from American Thoracic Society were applied in the survey. Fingernails were used as biomarker. Ten heavy metals elements in PM and fingernail samples were analysed using inductively coupled plasma mass spectrometry (ICP-MS). Results: The cadmium, chromium, copper, manganese, nickel and lead concentrations in PM around the MSW landfills and residential areas exceeded the Canada and USEPA standard permissible limit. Heavy metals in fingernails (p
    Matched MeSH terms: United States Environmental Protection Agency
  13. Abd Manan TSB, Khan T, Wan Mohtar WHM, Beddu S, Mohd Kamal NL, Yavari S, et al.
    Data Brief, 2020 Jun;30:105518.
    PMID: 32382595 DOI: 10.1016/j.dib.2020.105518
    Perak River basin is in Perak state of Peninsular Malaysia. In this research, the river stretch serves as water intake for domestic, agricultural and industrial purposes in Perak Tengah, Hilir Perak and Manjung regions. It is located in mixed use area whilst exposing the river to anthropogenic elements. The sampling locations were conducted at selected points of Perak River namely Tanjung Belanja Bridge (TBB), Water Treatment Plant Parit (WTPP), Parit Town discharge (PTD), Water Treatment Plant Senin (WTPS) and Water Treatment Plant Kepayang (WTPK). The existence of aromatic hydrocarbons in freshwater samples was pre-assessed via qualification analysis; specific ultraviolet absorbance (SUVA254) method at 254 nm of wavelength. The SUVA dataset were 48.38 L/mg-m (TBB), 50.54 L/mg-m (WTPP), 8.05 L/mg-m (PTD), 85.75 L/mg-m (WTPS) and 217.39 L/mg-m (WTPK). The SUVA254 values of fresh water at the river basin have exceeded the water quality standards value equivalent to 2.0 L/mg-m permitted by the Environmental Protection Agency of United States. The exceeding values were an indication of a large portion of aromatic compounds in the water. Qualification analyses evident the existence of water pollutants at treacherous concentrations for public health in freshwater samples of Perak River basin. Thus, this research has presented important findings towards further research and countermeasure for a better alternative of water treatment in Malaysia.
    Matched MeSH terms: United States Environmental Protection Agency
  14. McDaniel PA, Solomon G, Malone RE
    Environ Health Perspect, 2005 Dec;113(12):1659-65.
    PMID: 16330343
    Tobacco is a heavily pesticide-dependent crop. Because pesticides involve human safety and health issues, they are regulated nationally and internationally; however, little is known about how tobacco companies respond to regulatory pressures regarding pesticides. In this study we analyzed internal tobacco industry documents to describe industry activities aimed at influencing pesticide regulations. We used a case study approach based on examination of approximately 2,000 internal company documents and 3,885 pages of U.S. Environmental Protection Agency documents obtained through Freedom of Information Act requests. The cases involved methoprene, the ethylene bisdithiocarbamates, and phosphine. We show how the tobacco industry successfully altered the outcome in two cases by hiring ex-agency scientists to write reports favorable to industry positions regarding pesticide regulations for national (U.S. Environmental Protection Agency) and international (World Health Organization) regulatory bodies. We also show how the industry worked to forestall tobacco pesticide regulation by attempting to self-regulate in Europe, and how Philip Morris encouraged a pesticide manufacturer to apply for higher tolerance levels in Malaysia and Europe while keeping tobacco industry interest a secret from government regulators. This study suggests that the tobacco industry is able to exert considerable influence over the pesticide regulatory process and that increased scrutiny of this process and protection of the public interest in pesticide regulation may be warranted.
    Matched MeSH terms: United States Environmental Protection Agency
Filters
Contact Us

Please provide feedback to Administrator (afdal@afpm.org.my)

External Links