This paper is about the reduction of the overall size of metal blanking sheet that is being used to form a stamping product or car body panel of a car manufacturer in Malaysia. The current blanking sheet produces extra waste which will be recycled and does not contribute to increase productivity but increases inventory cost. The reduction in the blanking sheet size will lead to the reduction of raw material hence reduced the production cost. However, the reduced size of blanking sheet could affect the yield strength of the product. The study of the yield strength and yield improvement of the product are done by simulating stress analysis by using CATIA software. The results show that the new proposed size of the metal blanking sheet provides accuracy of the product dimension as well as maintaining the yield strength of the product and it reduced a significant amount of metal scrap which is nearly 4% of material weight and save around 10% of inventory cost.
Body Mass Index (BMI) is the most established anthropometric indicator used for assessment of nutritional status. Other anthropometric indicators which are related closely to BMI are waist hip ratio (WHR) and waist circumference. In this paper, receiver operating characteristics (ROC) curves were constructed to assess the value of waist circumference and waist hip ratio as a screening measure for the need of weight management using BMI as the reference test. Sensitivity and specificity were calculated at several cut-offs. The areas under the ROC curve calculated by comparing waist circumference with BMI were high (0.70 - 0.86) while the areas calculated for WHR were low (0.46 - 0.67). Sensitivities of 0.745 and 0.800 were observed at cut-off points of waist circumference at 90cm and 80cm for males and females respectively, while the false positive rates were 0.233 for males and 0.250 for females. These cut-off points could be considered as a fair trade-off. Therefore it is concluded that waist circumference performed better than WHR as a screening test. It is indicative that waist circumference could be used as a tool in raising awareness of weight management in this population.
Bridges are designed to withstand different types of loads, including dead, live, environmental, and occasional loads during their service period. Moving vehicles are the main source of the applied live load on bridges. The applied load to highway bridges depends on several traffic parameters such as weight of vehicles, axle load, configuration of axles, position of vehicles on the bridge, number of vehicles, direction, and vehicle's speed. The estimation of traffic loadings on bridges are generally notional and, consequently, can be excessively conservative. Hence, accurate prediction of the in-service performance of a bridge structure is very desirable and great savings can be achieved through the accurate assessment of the applied traffic load in existing bridges. In this paper, a review is conducted on conventional vehicle-based health monitoring methods used for bridges. Vision-based, weigh in motion (WIM), bridge weigh in motion (BWIM), drive-by and vehicle bridge interaction (VBI)-based models are the methods that are generally used in the structural health monitoring (SHM) of bridges. The performance of vehicle-assisted methods is studied and suggestions for future work in this area are addressed, including alleviating the downsides of each approach to disentangle the complexities, and adopting intelligent and autonomous vehicle-assisted methods for health monitoring of bridges.
High consumption of sugar-sweetened beverages (SSBs) among adolescents has turned into a global concern due to its negative impact on health. This cross-sectional study determined the amount of SSB consumption among adolescents and its associated factors. A total of 421 adolescents aged 13.3 ± 1.3 years (41.8% males, 58.2% females) completed a self-administered questionnaire on sociodemographic characteristics, physical activity, screen-viewing behavior, sleep quality, frequency of eating at fast food restaurants, home food availability, peer social pressure, parenting practice, and SSB consumption. Weight and height were measured. Results showed that the mean daily consumption of SSBs among adolescents was 1038.15 ± 725.55 mL. The most commonly consumed SSB was malted drink, while the least commonly consumed SSB was instant coffee. The multiple linear regression results revealed that younger age (β = -0.204, p < 0.001), higher physical activity (β = 0.125, p = 0.022), higher screen time (β = 0.147, p = 0.007), poorer sleep quality (β = 0.228, p < 0.001), and unhealthy home food availability (β = 0.118, p = 0.032) were associated with a higher SSB intake. Therefore, promoting a healthy lifestyle may help to reduce the excessive consumption of SSBs among adolescents.
In the initial clinical examination of a child with ambiguous genitalia an accurate measurement of the corporeal length is needed. Most often the corporeal length is measured with a ruler from the symphysis pubis to the tip of the glans of a stretched penis. More recently, ultrasound has been successfully used to measure corporeal length. This study aimed to (i) establish normal values for corporeal length in normal male newborns using ultrasound measurement, (ii) compare these measurements to stretched corporeal measurements, (iii) compare the corporeal length of newborns of different races, and (iv) determine the relationship between corporeal length and birth weight, birth length and head circumference. This was a prospective study of 141 newborns. Ultrasound imaging was done in an oblique parasagittal plane such that the corpus could be included in a single image and measured, Stretched corporeal length was measured with the penis stretched alongside a wooden spatula and the length from the pubic bone to the tip of the glans was marked on the spatula and measured. By ultrasound measurement the mean corporeal length of the normal newborn was 3.18 +/- 0.56cm. There was no significant difference in the mean corporeal length when determined by ultrasound and by stretched corporeal measurement. There was no significant difference in the mean corporeal length of the different races when the length was determined by either ultrasound or stretched corporeal measurement. There was a positive correlation between ultrasound length and birth weight and birth length. However, there was no correlation between ultrasound length and head circumference. There was no significant correlation between the stretched length and either birth weight, birth length or head circumference.
Matched MeSH terms: Body Weights and Measures/statistics & numerical data
A total of 341 fertilized and 37 unfertilized oocytes from 63 intracytoplasmic sperm injection (ICSI) treatment cycles were included for retrospective assessment using the Embryoscope time-lapse video system. The second polar body (pb2) extrusion occurred at 2.9±0.1 h (range 0.70-10.15 h) relative to sperm injection. All oocytes reduced in size following sperm injection (p<0.05) with shrinkage ceasing after 2h in the unfertilized and at pb2 extrusion in the fertilized oocytes. Pb2 extrusion was significantly delayed for women aged >38 years compared to those <35 years (3.4±0.2 vs. 2.8±0.1, p<0.01) or 35-38 years (3.4±0.2 vs. 2.8±0.1, p<0.01), but timing was not related to the Day 3 morphological grades (1-4) of subsequent embryos (2.9±0.1, 2.9±0.1, 2.8±0.2 and 3.0±0.1; p>0.05 respectively). A shorter time of first cleavage division relative to either sperm injection or pb2 extrusion is associated with both top grade (AUC=0.596 or 0.601, p=0.006 or 0.004) and usable embryos (AUC=0.638 or 0.632, p=0.000 respectively) on Day 3. In summary, (i) pb2 of human oocytes extrudes at various times following sperm injection, (ii) the timing of pb2 extrusion is significantly delayed when female age >38 years, but not related to subsequent embryo development, (iii) all human oocytes reduce in size following sperm injection, (iv) completion of pb2 extrusion in the fertilized oocytes is a pivotal event in terminating shrinkage of the vitellus, and (v) time to first cleavage division either from sperm injection or pb2 extrusion is a significant predictive marker for embryo quality on Day 3.
A bulk of used paper supplied to recycling industry may contain water in their internal voids. This is because the price of the used paper is currently based on their weight and it has a huge potential of suppliers to add with water in order to increase the price. Currently used methods for detecting moisture content in a paper are restricted to a sheet of paper only. This paper presents a non-intrusive method for quick and in-situ measurement of water content in a bulk of used paper. The proposed method extends the capability of common paper moisture gauge, by using a neutron device. A fast neutron source (Am-Be 241) and a portable backscattering neutron detector are used for water measurement. It theoretically indicates that the slow neutron counts can be correlated to the hydrogen or water level in a paper. The method has the potential of being used by the paper-recycling industry for rapid and non-destructive measurement of water in a bulk of used paper.
The purpose of this study was to determine the effects of 100% feedback frequencies, 65% of feedback frequencies and bandwidth feedback on overhand throwing skill among children and motivation of the children during practices. 60 of female students from range of aged 10 to 11 years old are participated in this study (age: M=10.53 years/SD=.503, weight: M=29.11/SD3.08, height=126.68/3.04). All participants practiced 60 trials of overhand throwing accuracy task and the motivation of the participant had been measured by using Intrinsic Motivation Inventory Questionnaire (IMI) (r=0.59). Participants were randomly assigned into three group 100% feedback, 65% feedback and bandwidth feedback groups. Learning was inferred from the performance on the delayed (24-hour) retention. To analyze the data, we use mixed-between ANOVA for practice phases, One Way ANOVA for retention test and correlation analysis to measure the relationship between feedback frequencies and motivation. There was no significant result between group (F (2, 57) =.286, p= .752) during practices, there is a significant difference on retention test phase (p
In a meristic, morphometric and distributional study of Neolissochilus from Peninsular Malaysia, Khaironizam et al. (2015) subsumed Lissochilus tweediei Herre in Herre & Myers 1937 and a taxon they called "Tor soro Bishop 1973" into the synonymy of N. soroides (Duncker 1904) based on data collected from museum specimens. However, "Bishop 1973" is not the correct author citation for Tor soro. Instead, Tor (now placed in Neolissochilus) soro was originally described as Barbus soro by Valenciennes in Cuvier & Valenciennes (1842:191). Since "Tor soro Bishop 1973" is not a valid name/author combination, Neolissochilus soro, as treated by Khaironizam et al. (2015), cannot be considered a junior synonym of N. soroides.
A series of ester compounds derived from ricinoleic acid to be used as biolubricants base stock have been synthesized. The resulting products were confirmed by FTIR and NMR analyses. The synthesis was carried out in three stages: epoxidation of ricinoleic acid; synthesis of 10,12-dihydroxy-9-acyloxystearic acid from epoxidized ricinoleic acid with various fatty acids and esterification of the acyloxystearic acid products with octanol to yield octyl-10,12-dihydroxy-9-acyloxystearate. The viscosities, flash points and pour points (PP) behavior of the products were measured. The resulting esters had an increased in molar weight and viscosity and decreased in pour points as compared to ricinoleic acid.
We put attention on Intrinsic Josephson Junction (IJJ) to study the fundamental physic for device applications. Convenient self-flux method was used to grow BSCCO single crystals. We investigated the lid effect to examine the single crystal growth of high TC (Critical Temperature). We found that for the crystal growth with no lid, two stage transitions of TC ≅ 61 K and 77 K were observed. While for the crystal growth with lid, the BSCCO has TC ≅ 80K, ΔTC = 10K and approximately average size5x2mm 2 . When we increased weight of lid, the single crystal have increased to TC =80K, ΔTC = 4K and the typical size was ≅7x3mm 2 . TC and the crystal growth show a tendency to increase by the effect of the lid. From observed quasi-particle characteristics, c-axis direction changed from semiconductor to intrinsic Josephson characteristic with decreasing temperature.
Accurate values are a must in medicine. An important parameter in determining the quality of a medical instrument is agreement with a gold standard. Various statistical methods have been used to test for agreement. Some of these methods have been shown to be inappropriate. This can result in misleading conclusions about the validity of an instrument. The Bland-Altman method is the most popular method judging by the many citations of the article proposing this method. However, the number of citations does not necessarily mean that this method has been applied in agreement research. No previous study has been conducted to look into this. This is the first systematic review to identify statistical methods used to test for agreement of medical instruments. The proportion of various statistical methods found in this review will also reflect the proportion of medical instruments that have been validated using those particular methods in current clinical practice.
Matched MeSH terms: Weights and Measures/instrumentation; Weights and Measures/standards
Previous reports of patients undergoing parathyroidectomy and of patients receiving teriparatide as antiosteoporotic treatment have suggested a plausible relationship between parathyroid hormone (PTH) and uric acid. However, similar data at population level were lacking. The current study aimed to determine the relationship between PTH and uric acid in a group of apparently healthy Malaysian men.
Sexual dimorphism is a common phenomenon in the animal kingdom. To test the consistency of sexual dimorphism patterns among sympatric species of the same genus, ten morphometric characteristics of mud crabs Scylla olivacea, S. tranquebarica and S. paramamosain were measured and compared using Discriminant Function Analysis (DFA). The descriptive analysis revealed that in all three species, body size dimensions and cheliped dimensions were significantly larger in males whereas the abdomen width was female-biased. Also, we described a morphological variation (carapace width, CW ≤ CW at spine 8, 8CW) that is unique to S. olivacea. Discriminant function analysis revealed that all nine morphometric characteristics were sexually dimorphic in S. olivacea, S. tranquebarica (except right cheliped's merus length, ML) and S. paramamosain (except 8CW). The obtained discriminant functions based on the morphometric ratios (with CW as divisor) correctly classified 100% of adults of known sex of all three species. Further, based on the selected body traits, DFA was able to almost completely distinguish males (94%), but not females (74%), among the three Scylla species. This study highlights that congeneric species of portunids (e.g., Scylla spp.) show similar sexually dimorphic characteristics (body size and secondary sexual characteristics).
To assist in the broadcasting of time-critical traffic information in an Internet of Vehicles (IoV) and vehicular sensor networks (VSN), fast network connectivity is needed. Accurate traffic information prediction can improve traffic congestion and operation efficiency, which helps to reduce commute times, noise and carbon emissions. In this study, we present a novel approach for predicting the traffic flow volume by using traffic data in self-organizing vehicular networks. The proposed method is based on using a probabilistic generative neural network techniques called deep belief network (DBN) that includes multiple layers of restricted Boltzmann machine (RBM) auto-encoders. Time series data generated from the roadside units (RSUs) for five highway links are used by a three layer DBN to extract and learn key input features for constructing a model to predict traffic flow. Back-propagation is utilized as a general learning algorithm for fine-tuning the weight parameters among the visible and hidden layers of RBMs. During the training process the firefly algorithm (FFA) is applied for optimizing the DBN topology and learning rate parameter. Monte Carlo simulations are used to assess the accuracy of the prediction model. The results show that the proposed model achieves superior performance accuracy for predicting traffic flow in comparison with other approaches applied in the literature. The proposed approach can help to solve the problem of traffic congestion, and provide guidance and advice for road users and traffic regulators.
Phenotypic selection of individuals is the first step in a selective breeding program for elite hybrid seed production. In
this study, a total of 295 Jatropha curcas individuals raised from cuttings representing 21 accessions, collected from eight
different countries were evaluated for growth performance. The evaluation was done at the Biodiesel Research Station
of Universiti Kebangsaan Malaysia, Kuala Pilah from December 2012 to December 2013. Individual plants from each
accession were observed on several agronomic and yield related traits and all the data were recorded periodically.
Performance of each accession was analyzed using Statistical Analysis System (SAS) 9.4. Four traits which were plant
height (PH), number of flowers per inflorescence (NFI), number of female flowers per inflorescence (NFFPI) and hundred
seed weight (HSW) showed significant differences among the accessions after one year of planting. Maximum values for
each trait were 115.5 cm for PH, 6 for number of branches per plant (BPP), 9 for number of inflorescences per plant
(NIPP), 25 for number of fruits per plant (NFPP), 5 for number of fruits per inflorescence (NFPI), 191 for NFI, 10 for
NFFPI, 81.0 g for HSW and 70 for number of seeds per plant (NSPP). Accession number 1 from Thailand showed the best
performance for most traits. A highly significant and positive correlation was found between NFPP and NSPP. Based on
superior trait values for NIPP, NFPP, NFPI, NFI, NFFPI and HSW, five plants from accession UKMJC 01, 04, 05, 13 and 14
have been selected for generating elite intraspecific hybrids.
CONTEXT: Selecting an appropriate size double-lumen tube (DLT) for one-lung ventilation has always been a challenge as most choose it based on experience or using the existing guidelines based on gender and height.
AIMS: The aim of this study was to determine if the appropriate choice of this tube could be based on the patients' height, weight, tracheal diameter (TD), or the left main stem bronchus diameter (LMBD) and also to determine the relationship between height and depth of insertion among Asians.
SUBJECTS AND METHODS: This was a retrospective review of 179 patients who were intubated with a left-sided DLT and also had a posterior-anterior view of a digital chest radiograph for tracheal and left main bronchus diameter measurements. Additional data collected included patients' demographics and DLT size used.
RESULTS: There were 123 (68.7%) males and 56 (31.3%) females with an overall mean age of 33.3 ± 16.3 years. Majority of the males (48.8%) used a size 39 Fr while females (46.4%) used a 35 Fr. There were weak correlations between DLT size with height (male: R2 = 0.222; female: R2 = 0.193), DLT size with weight (male: R2 = 0.109; female: R2 = 0.211), DLT size with TD (male: R2 = 0.027); female: R2 = 0.016), and DLT size with LMBD (male: R2 = 0.222; female: R2 = 0.193). There was a good correlation between depth of DLT inserted with patient's height for both genders.
CONCLUSION: The appropriate size of the left-sided DLT could not be predicted based on patients' height, weight, tracheal or left main bronchus diameter alone in Asians; however, the depth of insertion of the tube was dependent on the height in both genders.