MyMedR

Displaying publications 1 - 20 of 139 in total

Abstract:

Sort:

Fulltext Use of a reflectance spectroscopy accessory for optical characterization of ZnO-Bi(2)O(3)-TiO(2) ceramics

Ghazali MS, Zakaria A, Rizwan Z, Kamari HM, Hashim M, Zaid MH, et al.

Int J Mol Sci, 2011;12(3):1496-504.
PMID: 21673903 DOI: 10.3390/ijms12031496

The optical band-gap energy (E(g)) is an important feature of semiconductors which determines their applications in optoelectronics. Therefore, it is necessary to investigate the electronic states of ceramic ZnO and the effect of doped impurities under different processing conditions. E(g) of the ceramic ZnO + xBi(2)O(3) + xTiO(2), where x = 0.5 mol%, was determined using a UV-Vis spectrophotometer attached to a Reflectance Spectroscopy Accessory for powdered samples. The samples was prepared using the solid-state route and sintered at temperatures from 1140 to 1260 °C for 45 and 90 minutes. E(g) was observed to decrease with an increase of sintering temperature. XRD analysis indicated hexagonal ZnO and few small peaks of intergranular layers of secondary phases. The relative density of the sintered ceramics decreased and the average grain size increased with the increase of sintering temperature.

Matched MeSH terms: Ceramics/chemistry*
Fulltext Characterization and phase evolution of cordierite based glass synthesis from pure oxide and minerals

Banjuraizah Johar, Hasmaliza Mohamad, Zainal Arifin Ahmad

Journal of Nuclear and Related Technologies, 2009;2009(1):237-246.
MyJurnal

α Cordierite is very important phase in MgO-Al2O3-SiO2 system because of their very outstanding thermal, chemical and electrical properties. In this presents study nonstoichiometry cordierite (MgO:Al2O3:SiO2 = 3:1.5:5) using 2 different initial raw materials ( (i)mixture of pure oxide, and ii) mainly mixture of minerals) were fabricated and compared in terms of phase transformation and physical properties. Cordierite was prepared by glass method at low melting temperature (1350°C). Low melting temperature has resulted in partly crystalline glass which has possesses higher hardness, required longer milling time and result in contamination from grinding media. However, α-cordierite has successfully crystallized and fully densified at 850°C/2h. Activation energy for densification was investigated from thermal expansion coefficient (TCE) results. Other properties that were discussed included thermal properties using DTA/TGA.

Matched MeSH terms: Ceramics
Fulltext Synthesis and characterization of β-tricalcium phosphate ceramic via sol-gel method

Mohd Al Amin Muhamad Nor, Maryam Mohd Ridzuan, Zainal Arifin Ahmad

Journal of Nuclear and Related Technologies, 2009;2009(1):199-205.
MyJurnal

Ceramic materials play key role in several biomedical applications. One of them is bone graft which is use in treating bone defect which caused by injury or osteoporosis. Calcium phosphates based ceramic are preferred as bone grafts in hard tissue engineering because of their chemical compositions are similar to the composition of human bone, superior bioresorbable and bioactivity. In this study, β-tricalcium phosphate (β-TCP) ceramic was synthesized by using sol-gel method. Phosphorous pentoxide (P2O5) and calcium nitrate tetrahydrate (Ca(NO3)2.4H2O) were used as calcium and phosphate precursors. The effects of calcination temperature on the synthesis powder were studied using the XRD, SEM-EDS and FTIR techniques. It was found that calcination temperature greatly influence the purity of the synthesized powders. The β-TCP was the dominant phase with the formation of α-TCP at calcination temperature from 600 to 800°C. Pure β-TCP was obtained at calcination of 900°C. As the temperature increased to 1000°C, the β-TCP was decomposed to for calcium phosphate oxide (CPO). The sol-gel method has some advantages over other methods, mainly its simplicity and ability to produce pure β-TCP at lower calcination temperature.

Matched MeSH terms: Ceramics
Fulltext Effect of slurries density on the properties of ceramic foam produced via polymer replication method

Mohd Al Amin Muhamad Nor, Lee, Chain Hong, Hazizan Md. Akil, Zainal Arifin Ahmad

Journal of Nuclear and Related Technologies, 2007;2005(1):35-41.
MyJurnal

Ceramic foams are a class of high porosity materials that are used or being considered for a wide range of technological applications. Ceramic foam was produce by polymer replication method. In this process, commercial polymeric sponge was use as template, dipping with ceramic particles slurry, drying and then sintered to yield a replica of the original foams. The study was focus on the fabrication of different density of ceramic foams by varying the density of ceramic slurries (1.1876, 1.2687, 1.3653 and 1.5295 g/cm3). Properties of ceramic foam produced such as density was characterized accordingly to ASTM C 271-94 and porosity were characterized using Archimedes methods. Compressive and bending strength was performed accordingly to ASTM C1161-94 and C773-88 (1999), respectively. The morphological study was performed using Scanning Electron Microscopy (SEM) and EDX. Density of ceramic foams produced was about 0.5588 and 1.1852 g/cm3, where as porosity was around 26.28 and 70.59 %. Compressive and bending strength was increase from strength also increases from 2.60 to 23.07 MPa and 1.20 to 11.10 MPa, respectively, with increasing of slurries density from 1.1876 to 1.3653 g/cm3. The SEM micrographs show that the cells structure become denser as the slurries density increased. EDX proved that the ceramic used is porcelain. As a conclusion, increasing in slurries density produced ceramic foams with good mechanical properties such as compressive and bending strength and denser body.

Matched MeSH terms: Ceramics
Fulltext Correlation between the bending strength and the thickness interlayer of alumina-mild steel friction welded at lower rotational speed

Mohamad Zaky Noh, Luay Bakir Hussain, Zainal Arifin Ahmad

Journal of Nuclear and Related Technologies, 2007;2007(1):75-82.
MyJurnal

The joining of ceramic-metal could be done through a few techniques: brazing, diffusion bonding, friction welding etc. However, the mechanism of ceramic-metal joining was still not properly understood. In this study, alumina rod was bonded to mild steel rod via friction welding technique by using Al 1100 sheet as interlayer. The diameter of the rods was 10 mm. Friction pressure of 20 MPa and forging pressure of 40 MPa were used. Rotational speeds were maintained at 900 rpm and friction times of 2 to 20 seconds were applied. The joining strength was determined through four point bending test. The maximum bending strength, 240 MPa was obtained at the friction times of 20 seconds. Under optical microscope and SEM observation, the deformation of the aluminum interface was clearly obtained. Mechanical interlocking and close contact between the aluminaaluminum and aluminum-mild steel were observed at magnifications of 3000X. The strength of alumina-steel bonding is much dependent on the wettability of the alumina surface by the molten aluminum and the existing of mechanical interlocking between interlayer and sample materials.

Matched MeSH terms: Ceramics
Fulltext The effects of CR2O3 addition on microstructure and fracture toughness of ZTA ceramic composite

Ahmad Zahirani Ahmad Azhar, Hasmaliza Mohamed, Mani Maran Ratnam, Zainal Arifin Ahmad

Journal of Nuclear and Related Technologies, 2013;2013(2):9-15.
MyJurnal

The microstructure and mechanical properties of ceramic composites produced from alumina, yttria stabilized zirconia and chromia oxide system was investigated. The Cr2O3 weight percent was varied from 0 wt% to 1.0 wt%. Each batch of composition was mixed, uniaxially pressed to 13mm diameter and sintered at 1600 ◦C for 4 h in pressureless conditions. Studies on the effects of the sample microstructures on their mechanical and physical properties such as fracture toughness and bulk density were carried out. Results show that an addition of 0.6 wt% of Cr2O3 produces the best mechanical properties. Furthermore, microstructural observations show that the Al2O3 grain size is significantly dependent on the amount of Cr2O3 additives used. Maximum value obtained with 0.6 wt % Cr2O3 for the fracture toughness is 5.36 MPa.m1/2.

Matched MeSH terms: Ceramics
Fulltext Rietveld quantitative phase analysis of non-stoichiometric cordierite synthesised from mainly talc and kaolin: effect of sintering temperature

Banjuraizah Johar, Hasmaliza Mohamad, Zainal Arifin Ahmad

Journal of Nuclear and Related Technologies, 2009;2009(1):103-110.
MyJurnal

Indialite or α-cordierite was synthesized by glass crystallization method using mainly talc and kaolin and with small amount of MgO, Al2O3, SiO2 to compensate the chemical formulation of non-stoihiometric compositions of cordierite. (3MgO.1.5Al2O3.5SiO2). B2O3, P2O5 and CaO was also added to decrease the melting and sintering temperature of cordierite. The glasses were pelletized and sintered from 850 o C up to 1050 o C. Phase compositions of both heat treated glass was quantified by X-ray powder diffraction data by the Rietveld method using TOPAS Ver 3 software. Result shows that about 60wt% of α cordierite has successfully crystallized at 850 o C. Beside secondary phases (forsterite) which come from initial raw materials, phases from grinding media were also presents in the sample. The contamination was considered high since it has reacted with existence phases to form a new phase at higher temperature. Without any contamination from grinding it was expected to obtain more than 90wt% α cordierite using the same composition.

Matched MeSH terms: Ceramics
Fulltext Electrodeposition of nickel-phosphorus-alumina composite coatings

Nur Azam Badarulzaman, Ng, Jun Wei, Ahmad Azmin Mohamad, Purwadaria, Sunara, Zainal Arifin Ahmad

Journal of Nuclear and Related Technologies, 2009;2009(1):43-50.
MyJurnal

A co-deposition of nickel-phosphorus-alumina (NiPA) composite coatings were obtained from an ordinary sulphate-based plating bath consisting of 5 g/l alumina (Al2O3) particles. The particles were dispersed by using mechanical agitation at 125 rpm. The presence of Ni3P and Al2O3 phases in the coatings was confirmed by XRD analysis. SEM/EDX results indicated that a smooth Ni3P coating was obtained and Al2O3 particles were embedded into the coating. Microscopic observation showed that the bonding between the Ni3P metal matrix and the Al2O3 ceramic particles was compact.

Matched MeSH terms: Ceramics
Study on changing the coefficient of thermal expansion (CTE) of dental porcelain

Jamaluddin O, Zainal AA

Med J Malaysia, 2004 May;59 Suppl B:143-4.
PMID: 15468859

Raising the thermal expansion coefficient (CTE) of dental porcelains is important to match the CTE of the ceramic material with the higher CTE of the metal inlay in dental restorations. The higher thermal expansion of the leucite phase increases the overall thermal expansion coefficient of the dental porcelain. Potassium nitrate (KNO3) additions in controlled percentages to the base dental porcelain formulation help in the formation of a leucite phase. The percentage added was 5,10 and 20 weight percent of leucite, respectively, to the total base frit composition. The change in CTE values was then investigated using a Linseis Dilatometer. A 20wt% KNO3 addition resulted in a CTE of 9.0 microm/m-K compared to the 7.7 microm/m-K CTE of the base composition. The microstructures observed under the scanning electron microscope (SEM) show a multiphase material with the leucite phases dispersed within a glassy matrix. The results suggest that higher CTEs in the dental porcelain are possible by increasing the KNO3- additions within the limits tested.

Matched MeSH terms: Ceramics/analysis*
Fulltext Heat treatment effect with the electrode contact of CaCu3Ti4O12

Muhammad Azwadi Sulaiman, Hutagalung, Sabar D., Zainal A. Ahmad

Journal of Nuclear and Related Technologies, 2013;2013(2):43-52.
MyJurnal

CaCu3Ti4O12 (CCTO) has attracted a great attention for electronic devices miniaturization due to its
very high dielectric constant properties at a wide range of frequency and nearly constant over broad temperature range. The origins of the giant dielectric constant have been speculated from electrical heterogeneous of interior elements of the CCTO ceramics. Four origins were suggested contributed to the electrical heterogeneous. In this study heat treatment were done with the electrode contact in Argon gas environment and the electrical properties over very wide frequency of CCTO ceramics were investigated. Cylindrical CCTO pellets samples were prepared by solid state reaction method and single phase of XRD pattern was obtained after sintering processes. Electrical impedance responds were measured at frequency from 100 Hz to 1 GHz for the samples for untreated and heat treated at 200ºC, 250ºC, 300ºC, 350ºC and 400ºC of CCTO. Improvement to the dielectric constant can be seen for 350ºC and 400ºC samples and dielectric loss were improved for 200ºC and 300ºC samples for overall frequency. The variations were discussed based on oxygen deficiency content and resistivity of the elements inside of CCTO structure.

Matched MeSH terms: Ceramics
Fulltext Midterm Results of Conversion from Failed Bipolar Hemiarthroplasty to Total Hip Arthroplasty

Park KS, Chan CK, Lee DH, Yoon TR

Indian J Orthop, 2018 8 7;52(4):369-373.
PMID: 30078894 DOI: 10.4103/ortho.IJOrtho_494_16

Background: Conversion from failed bipolar hemiarthroplasty (HA) to total hip arthroplasty (THA) presents a great challenge to orthopedic surgeons for bipolar head removal and cup placement with or without change of femoral stem. Conversion THA after failed bipolar arthroplasty is known to offer both symptomatic and functional improvement. This study evaluates the midterm functional outcome and complications, especially dislocation associated with femoral head diameter, after conversion THA.
Materials and Methods: Forty eight hips with the conversion of bipolar HA to THA were followed up for an average 6.2 years (range 2.0-11.5 years). Twenty one hips had conversion surgery to THA using metal-on-metal articulation (28 or 32 mm head). Nine hips used ceramic-on-ceramic (28-40 mm) and eighteen hips used large head metal-on-metal bearing (>40 mm). Outcome was evaluated using Harris Hip Score (HHS) and Western Ontario McMaster Universities Osteoarthritis Index (WOMAC) score. The radiographs were analyzed for evidence of osteolysis and/or loosening. The complications were evaluated, especially dislocation with different femoral head diameter.
Results: Average HHS significantly improved from 42 preoperatively to 86 postoperatively and the average WOMAC score also significantly improved from 47 to 22 postoperatively. Radiological evaluation showed all the femoral components were stable. There was one acetabular component loosening, which required revision 9 years after conversion to THA. One dislocation and one recurrent dislocation were recorded in isolated acetabular revision hip; whereas one dislocation, one recurrent dislocation, and one trochanteric nonunion occurred in the hips with revision of both components. All dislocations occurred in hips with a femoral head size of 28 mm (P = 0.052). The cup and femoral head interval length was the most significant factor contributing to dislocation (P = 0.013).
Conclusions: Conversion THA after failed bipolar HA offers a reliable pain relief and functional improvement. To prevent dislocation, it is highly recommended to use a larger diameter femoral head, especially where the cup size is big.

Matched MeSH terms: Ceramics
Revision total hip arthroplasty with metal on metal bearing for ceramic bearing fractures

Park KS, Chan CK, Kim SK, Li QS, Im CJ, Yoon TR

J Orthop Sci, 2019 May;24(3):452-457.
PMID: 30415823 DOI: 10.1016/j.jos.2018.10.016

BACKGROUND: Due to concern of potential metallosis caused by residual microscopic ceramic particles, metal-on-metal (MoM) bearing is deemed undesirable in revision total hip arthroplasty (THA) for ceramic bearing fracture. We determined whether MoM bearing is suitable to be used in revision THA for ceramic fractures and also evaluated whether this treatment increases serum iron levels compared with MoM bearing revision THA for polyethylene failure.
METHODS: Between 2006 and 2012, 22 patients underwent revision surgery using MoM bearing (28 mm femoral head in 18 hips and 32 mm in 4 hips) for ceramic bearing fracture and followed average 52.1 months. We assessed radiological parameter and functional outcome using Harris hip score (HHS) and WOMAC score. Also, serum cobalt (Co) and chromium (Cr) blood tests were performed and compared with the result obtained from age, sex- and follow-up duration-matched patients with MoM revision THA for failed polyethylene bearing.
RESULTS: The mean HHS improved from 60.6 preoperatively to 90.3 at final follow-up. There were no changes in cup position, progression of osteolytic lesions, and measurable wear of MoM bearing articulation at final follow-up radiographs. There was one case of recurrent dislocation after surgery, which was treated with greater trochanter distal advancement and one case of deep infection, which underwent two-stage revision. Mean serum Co level (1.7 vs. 1.4 μg/dl; p = 0.211) and Cr level (0.70 vs. 1.01 μg/dl; p = 0.327) showed no significant difference.
CONCLUSIONS: MoM articulation with liner cementation into the acetabular cup along with total synovectomy can be chosen in revision surgery for ceramic fracture with good midterm follow-up. However, the use of MoM bearing is indicated when the stem and metal shell can be retained and ceramic on ceramic or ceramic on polyethylene bearing cannot be selected. Also long-term outcome needs to be further evaluated.

Matched MeSH terms: Ceramics*
Macroporous bioceramics: a remarkable material for bone regeneration

Lew KS, Othman R, Ishikawa K, Yeoh FY

J Biomater Appl, 2012 Sep;27(3):345-58.
PMID: 21862511 DOI: 10.1177/0885328211406459

This review summarises the major developments of macroporous bioceramics used mainly for repairing bone defects. Porous bioceramics have been receiving attention ever since their larger surface area was reported to be beneficial for the formation of more rigid bonds with host tissues. The study of porous bioceramics is important to overcome the less favourable bonds formed between dense bioceramics and host tissues, especially in healing bone defects. Macroporous bioceramics, which have been studied extensively, include hydroxyapatite, tricalcium phosphate, alumina, and zirconia. The pore size and interconnections both have significant effects on the growth rate of bone tissues. The optimum pore size of hydroxyapatite scaffolds for bone growth was found to be 300 µm. The existence of interconnections between pores is critical during the initial stage of tissue ingrowth on porous hydroxyapatite scaffolds. Furthermore, pore formation on β-tricalcium phosphate scaffolds also allowed the impregnation of growth factors and cells to improve bone tissues growth significantly. The formation of vascularised tissues was observed on macroporous alumina but did not take place in the case of dense alumina due to its bioinert nature. A macroporous alumina coating on scaffolds was able to improve the overall mechanical properties, and it enabled the impregnation of bioactive materials that could increase the bone growth rate. Despite the bioinertness of zirconia, porous zirconia was useful in designing scaffolds with superior mechanical properties after being coated with bioactive materials. The pores in zirconia were believed to improve the bone growth on the coated system. In summary, although the formation of pores in bioceramics may adversely affect mechanical properties, the advantages provided by the pores are crucial in repairing bone defects.

Matched MeSH terms: Ceramics*
Electrochemical Characteristics of a Polymer/Garnet Trilayer Composite Electrolyte for Solid-State Lithium-Metal Batteries

Walle KZ, Musuvadhi Babulal L, Wu SH, Chien WC, Jose R, Lue SJ, et al.

ACS Appl Mater Interfaces, 2021 Jan 20;13(2):2507-2520.
PMID: 33406841 DOI: 10.1021/acsami.0c17422

Although solid-state Li-metal batteries (LMBs) featuring polymer-based solid electrolytes might one day replace conventional Li-ion batteries, the poor Li-ion conductivity of solid polymer electrolytes at low temperatures has hindered their practical applications. Herein, we describe the first example of using a co-precipitation method in a Taylor flow reactor to produce the metal hydroxides of both the Ga/F dual-doped Li7La3Zr2O12 (Ga/F-LLZO) ceramic electrolyte precursors and the Li2MoO4-modified Ni0.8Co0.1Mn0.1O2 (LMO@T-LNCM 811) cathode materials for LMBs. The Li/Nafion (LiNf)-coated Ga/F-LLZO (LiNf@Ga/F-LLZO) ceramic filler was finely dispersed in the poly(vinylidene fluoride)/polyacrylonitrile/lithium bis(trifluoromethanesulfonimide)/succinonitrile matrix to give a trilayer composite polymer electrolyte (denoted "Tri-CPE") through a simple solution-casting. The bulk ionic conductivity of the Tri-CPE at room temperature was approximately 4.50 × 10-4 S cm-1 and exhibited a high Li+ ion transference number (0.84). It also exhibits a broader electrochemical window of 1-5.04 V versus Li/Li+. A full cell based on a CR2032 coin cell containing the LMO@T-LNCM811-based composite cathode, when cycled under 1 C/1 C at room temperature for 300 cycles, achieved an average Columbic efficiency of 99.4% and a capacity retention of 89.8%. This novel fabrication strategy for Tri-CPE structures has potential applications in the preparation of highly safe high-voltage cathodes for solid-state LMBs.

Matched MeSH terms: Ceramics
Influence of sodalite zeolite infiltration on the coefficient of thermal expansion and bond strength of all-ceramic dental prostheses

Naji GA, Omar RA, Yahya R

J Mech Behav Biomed Mater, 2017 03;67:135-143.
PMID: 28006713 DOI: 10.1016/j.jmbbm.2016.12.007

In all-ceramic systems, a high incidence of veneer chip-off has been reported in clinical studies. Coefficient of thermal expansion (CTE) behaviour is one of the factors that may increase residual stress in the interface and influence the veneer/core bond strength. Therefore, this study aimed to evaluate the effect of sodalite zeolite-infiltration on the CTE behaviour and bond strength of different all-ceramic prostheses. The case-study groups were synthesized sodalite zeolite-infiltrated alumina (IA-SOD) and synthesized sodalite zeolite-infiltrated zirconia-toughened alumina (ZTA) (IZ-SOD), while the control groups were glass-infiltrated alumina (IA-glass) and glass-infiltrated ZTA (IZ-glass). Forty cylindrical-shaped samples measuring 5 mm in diameter and 10 mm in height were tested for CTE using a thermo-mechanical analyser machine, and forty disc-shaped ceramic samples measuring 12 mm in diameter and 1.2 ± 0.2 mm in thickness were prepared using specially designed stainless steel split mould and veneered by cylinder-shaped (2 mm high × 2 mm diameter) low-fusing porcelain (Vita VM7). The veneer/core samples were sintered and tested for shear bond strength using a high precision universal testing machine. Scanning electron microscope, stereo microscope, atomic force microscope, and energy-dispersive X-ray spectroscopy were used to investigate the structural characteristics of samples at the fracture surface. The collected data were analyzed with a one-way ANOVA and Tukey HSD test (α=.05). IZ-SOD revealed highest CTE and shear bond strength values, while the IA-glass revealed the lowest values than the other groups. There was no significant difference in CTE and bond strength among IZ-SOD, IA-SOD and IZ-glass samples (p>0.05). The experimental SOD zeolite-infiltrated samples revealed higher CTE mismatch and bond strength along with a more favourable mode of failure than did the commercial glass-infiltrated samples. Sandblast technique is considered as effective conditioning procedure for enhancing the surface roughness of SOD zeolite-infiltrated frameworks which subsequently improving the bond strength.

Matched MeSH terms: Ceramics*
Strain measurements and fracture resistance of endodontically treated premolars restored with all-ceramic restorations

Seow LL, Toh CG, Wilson NH

J Dent, 2015 Jan;43(1):126-32.
PMID: 25448436 DOI: 10.1016/j.jdent.2014.10.001

OBJECTIVES: The aim of this study was to investigate the recovery of cuspal stiffness and fracture resistance in endodontically treated maxillary premolars restored with bonded ceramic inlays and onlays of various designs.
METHODS: Seventy intact premolars were selected for this study; six cavity designs were investigated: (i) mesio-occlusal-distal (MOD) inlay (I), (ii) MOD inlay with palatal cusp coverage (IPC), (iii) MOD onlay (O), (iv) MOD inlay with pulp chamber extension (IPE), (v) MOD inlay with palatal cusp coverage and pulp chamber extension (IPCPE), and (vi) MOD onlay with pulp chamber extension (OPE). Intact teeth acted as control. Strain gauges were attached to the buccal and palatal surfaces of the teeth to measure cuspal stiffness under static loading. All specimens were eventually subjected to compressive load to failure. Cuspal stiffness and fracture resistance data were analyzed using ANOVA and Tukey test.
RESULTS: The I and IPE restorations restored cuspal stiffness to 75% of the sound tooth value. The O and OPE restored teeth had stiffness values greater than that of a sound tooth. The I, IPC, O, IPE, IPCPE and OPE restored teeth demonstrated fracture strength values of 938N±113 N (s.d.), 1073N±176 N and 1317N±219 N, 893N±129 N, 1062N±153 N and 1347N±191 N respectively.
CONCLUSIONS: Within the limitations of this study, it was concluded that the all-ceramic onlay or inlay with palatal cusp coverage provided best biomechanical advantage in restoring an endodontically treated maxillary premolar tooth.
CLINICAL SIGNIFICANCE: The onlay approach which is more conservative compared to full coverage restoration is considered an appropriate approach to the restoration of endodontically treated maxillary premolars. The addition of a pulpal extension to the all-ceramic restorations, apart from being technically challenging, was not found to offer any biomechanical advantage to the restored teeth.
KEYWORDS: Endodontically treated teeth; Fracture strengths; Inlay; Onlay; Pulp chamber extension; Strains

Matched MeSH terms: Ceramics
Remaining tooth structure associated with various preparation designs for the endodontically treated maxillary second premolar

Seow LL, Toh CG, Wilson NH

Eur J Prosthodont Restor Dent, 2005 Jun;13(2):57-64.
PMID: 16011232

Existing literature suggests a relationship between the amount of remaining tooth structure and the fracture resistance of the restored endodontically treated tooth. This study investigated the amount of tooth structure remaining following various tooth preparations used in the restoration of the endodontically treated maxillary second premolar. Illustrations of the maxillary second premolar in buccopalatal, mesiodistal and occlusal sections were drawn to scale. Outlines of various intra- and extracoronal preparations were superim-posed on the illustrations to reveal the amount of tooth tissue remaining in each case. Preparations for a ceramic inlay, inlay with palatal cusp coverage and onlay left 2.0-2.5mm of tooth structure buccally and palatally. Following preparation for a metal-ceramic crown, approximately 1.0mm of tooth structure remained buccally, and between 1.6mm-1.8mm palatally. Preparation for an all-ceramic crown was observed to leave 1.0mm-1.2mm of tooth structure surrounding what remained of the endodontic access cavity. It was concluded that decisions as to the type of definitive restoration to restore the endodontically treated maxillary second premolar may be influenced, amongst other factors, by information on the amount of tooth tissue remaining following preparation.

Matched MeSH terms: Ceramics
Fulltext An audit of the turnaround time of fixed prosthodontics cases in the ceramic laboratory

Khan, A., Mohd Noor, N.S., Sukumaran, P., Sheikh Aladin, S.H.A., Wai Ying, Y.

Ann Dent, 2016;22(2):1-8.
MyJurnal

This clinical audit is aimed to provide an insight into the performance of dental technicians in rendering
fixed prosthodontics services at Faculty of Dentistry, University of Malaya. A retrospective audit was
carried out between 1st of November 2014 and 31st January 2015 using data derived from records and
monthly returns of the technicians, which are kept at the ceramic laboratory. Retrospective data on
cases of diagnostic wax-ups, full metal crowns, metal ceramic crowns, all ceramic crowns and bridges
that were sent to ceramic laboratory for fabrication from 1st of September 2013 to 31st of August 2014
was systematically extracted from the record and tabulated categorically in SPSS version 22.0. The
turnaround time in workings day for diagnostic wax-ups and the prostheses was calculated by deducting
exit date from entry date. Subsequently, the turnaround time and the complexity of cases were categorized
accordingly. The association of turnaround time and the complexity of the cases was analysed using
Fisher Exact test with p value < 0.05. Within this time frame, a total of 102 cases of diagnostic waxups,
36 cases of crown and 18 cases of bridges were fabricated. 57.8% of diagnostic wax-ups were
completed within 3 days. 100% of 1 unit crown were completed within 7 days and 94.4% of bridges were
completed within 14 days. There was a significant association of turnaround time and the complexity of
the cases for diagnostic wax-ups and crowns with p value

Matched MeSH terms: Ceramics
Surface properties of Indonesian-made narrow dynamic compression plates

Dewo P, Sharma PK, van der Tas HF, van der Houwen EB, Timmer M, Magetsari R, et al.

Med J Malaysia, 2008 Jul;63 Suppl A:21-2.
PMID: 19024964

The enormous need of orthopaedic (surgical) implants such as osteosynthesis plates is difficult to be fulfilled in developing countries commonly rely on imported ones. One of the alternatives is utilization of local resources, but only after they have been proven safe to use, to overcome this problem. Surface properties are some of the determining factors of safety for those implants. We have succeeded in developing prototype of osteosynthesis plate and the results indicate that Indonesian-made plates need improvement with regards to the surface quality of physical characterization.

Matched MeSH terms: Ceramics
Fulltext "Ormocer an innovative technology": A replacement for conventional cements and veneer? A comparative in vitro analysis

Rajeev V, Arunachalam R, Nayar S, Arunima PR, Ganapathy S, Vedam V

Eur J Dent, 2017 4 25;11(1):58-63.
PMID: 28435367 DOI: 10.4103/ejd.ejd_113_16

OBJECTIVE: This in vitro study was designed to assess shear bond strength (SBS) of ormocer flowable (OF) resin as a luting agent, ormocer as an indirect veneer material with portrayal of modes of failures using scanning electron microscope (SEM).
MATERIALS AND METHODS: Sixty maxillary central incisors were divided into Group I, II, and III with 20 samples each based on luting cement used. They were OF, self-adhesive (SA) cement, and total etch (TE) cement. These groups were subdivided into "a" and "b" of ten each based on the type of veneering materials used. Veneer discs were fabricated using Ormocer restorative (O) and pressable ceramic (C). Specimens were thermocycled and loaded under universal testing machine for SBS. The statistical analysis was done using one-way ANOVA post hoc Tukey honest significant difference method.
RESULTS: A significant difference was observed between the Groups I and II (P < 0.05). The highest mean bond strength when using ormocer veneer was obtained with the Group Ia (19.11 ± 1.92 Mpa) and lowest by Group IIa (8.1 ± 1.04 Mpa), whereas the highest mean bond strength while using ceramic veneer was of similar range for Group Ib (18.04 ± 4.08 Mpa) and Group IIIb (18.07 ± 1.40 Mpa). SEM analysis revealed OF and TE presented mixed type of failure when compared with SA where failure mode was totally adhesive.
CONCLUSION: OF was found equally efficient like TE. Bond strength of ormocer as a veneer was not inferior to ceramic making it one of the promising additions in the field of dentistry.

Matched MeSH terms: Ceramics; Organically Modified Ceramics

Filters

Please provide feedback to Administrator (afdal@afpm.org.my)

External Links