Displaying publications 221 - 240 of 739 in total

Abstract:
Sort:
  1. Fulltext Experimental Analysis of Heat-Affected Zone (HAZ) in Laser Cutting of Sugar Palm Fiber Reinforced Unsaturated Polyester Composites
    Masoud F, Sapuan SM, Ariffin MKAM, Nukman Y, Bayraktar E
    Polymers (Basel), 2021 Feb 26;13(5).
    PMID: 33652612 DOI: 10.3390/polym13050706
    In this paper, the influence of processing input parameters on the heat-affected zone (HAZ) of three different material thicknesses of sugar palm fiber reinforced unsaturated polyester (SPF-UPE) composites cut with a CO2 laser was investigated. Laser power, traverse speed, and gas pressure were selected as the most influential input parameters on the HAZ to optimize the HAZ response with fixing all of the other input parameters. Taguchi's method was used to determine the levels of parameters that give the best response to the HAZ. The significance of input parameters was also determined by calculating the max-min variance of the average of the signal-to-noise ratio (S/N) ratio for each parameter. Analysis of variation (ANOVA) was used to determine each input parameter's contribution to the influence on HAZ depth. The general results show that the minimum levels of laser power and the highest levels of traverse speed and gas pressure gave the optimum response to the HAZ. Gas pressure had the most significant effect on the HAZ, with contribution decreases as the material thickness increased, followed by the traverse speed with contribution increases with the increase in material thickness. Laser power came third, with a minimal contribution to the effect on the HAZ, and it did not show a clear relationship with the change in material thickness. By applying the optimum parameters, the desired HAZ depth could be obtained at relatively low values.
    Matched MeSH terms: Hot Temperature
  2. Fulltext Sustainable Production of Arecanut Husk Ash as Potential Silica Replacement for Synthesis of Silicate-Based Glass-Ceramics Materials
    Anuar MF, Fen YW, Azizan MZ, Rahmat F, Mohd Zaid MH, Khaidir REM, et al.
    Materials (Basel), 2021 Feb 28;14(5).
    PMID: 33670923 DOI: 10.3390/ma14051141
    Arecanut husk (AH) was selected as a material for silica replacement in the synthesis process of glass-ceramics zinc silicate and also the fact that it has no traditional use and often being dumped and results in environmental issues. The process of pyrolysis was carried out at temperature 700 °C and above based on thermogravimetric analysis to produce arecanut husk ash (AHA). The average purity of the silica content in AHA ranged from 29.17% to 45.43%. Furthermore, zinc oxide was introduced to AHA and zinc silicate started to form at sintering temperature 700 °C and showed increased diffraction intensity upon higher sintering temperature of 600 °C to 1000 °C based on X-ray diffraction (XRD) analysis. The grain sizes of the zinc silicate increased from 1011 nm to 3518 nm based on the morphological studies carried out by field emission scanning electron microscopy (FESEM). In addition, the optical band gap of the sample was measured to be in the range from 2.410 eV to 2.697 eV after sintering temperature. From the data, it is believed that a cleaner production of low-cost zinc silicate can be achieved by using arecanut husk and have the potential to be used as phosphors materials.
    Matched MeSH terms: Hot Temperature
  3. Fulltext Self-Fluxing Mechanism in Geopolymerization for Low-Sintering Temperature of Ceramic
    Jamil NH, Abdullah MMAB, Pa FC, Mohamad H, Ibrahim WMAW, Amonpattaratkit P, et al.
    Materials (Basel), 2021 Mar 10;14(6).
    PMID: 33801862 DOI: 10.3390/ma14061325
    Kaolin, theoretically known as having low reactivity during geopolymerization, was used as a source of aluminosilicate materials in this study. Due to this concern, it is challenging to directly produce kaolin geopolymers without pre-treatment. The addition of ground granulated blast furnace slag (GGBS) accelerated the geopolymerization process. Kaolin-GGBS geopolymer ceramic was prepared at a low sintering temperature due to the reaction of the chemical composition during the initial stage of geopolymerization. The objective of this work was to study the influence of the chemical composition towards sintering temperature of sintered kaolin-GGBS geopolymer. Kaolin-GGBS geopolymer was prepared with a ratio of solid to liquid 2:1 and cured at 60 °C for 14 days. The cured geopolymer was sintered at different temperatures: 800, 900, 1000, and 1100 °C. Sintering at 900 °C resulted in the highest compressive strength due to the formation of densified microstructure, while higher sintering temperature led to the formation of interconnected pores. The difference in the X-ray absorption near edge structure (XANES) spectra was related to the phases obtained from the X-ray diffraction analysis, such as akermanite and anothite. Thermal analysis indicated the stability of sintered kaolin-GGBS geopolymer when exposed to 1100 °C, proving that kaolin can be directly used without heat treatment in geopolymers. The geopolymerization process facilitates the stability of cured samples when directly sintered, as well as plays a significant role as a self-fluxing agent to reduce the sintering temperature when producing sintered kaolin-GGBS geopolymers.
    Matched MeSH terms: Hot Temperature
  4. Fulltext Preheated (Heat-Assisted) Clinching Process for Al/CFRP Cross-Tension Specimens
    Lin PC, Fang JC, Lin JW, Tran XV, Ching YC
    Materials (Basel), 2020 Sep 19;13(18).
    PMID: 32961763 DOI: 10.3390/ma13184170
    Effects of processing parameters on preheated (heat-assisted) clinching process to join aluminum alloy 5052-H32 (AA5052) and thermoplastic carbon-fiber-reinforced-plastic (TP-CFRP) sheets for cross-tension (CT) specimens were first studied. Preheating was critical since brittle TP-CFRP could be softened to avoid fracturing or cracking during clinching process. Four processing parameters, including punching force, die depth, heating mode, and heating temperature, were considered. Quasi-static tests and microscope observations were taken to evaluate AA5052/TP-CFRP clinch joints in CT specimens and determine appropriate processing parameters for fatigue tests. Finally, fatigue data and failure mode of clinch joints in CT specimens were obtained and discussed.
    Matched MeSH terms: Hot Temperature
  5. Fulltext MHD radiative nanofluid flow induced by a nonlinear stretching sheet in a porous medium
    Jafar AB, Shafie S, Ullah I
    Heliyon, 2020 Jun;6(6):e04201.
    PMID: 32637680 DOI: 10.1016/j.heliyon.2020.e04201
    In this article, we numerically investigate the influence of thermal radiation and heat generation on the flow of an electrically conducting nanofluid past a nonlinear stretching sheet through a porous medium with frictional heating. The partial differential equations governing the flow problems are reduced to ordinary differential equations via similarity variables. The reduced equations are then solved numerically with the aid of Keller box method. The influence of physical parameters such as nanoparticle volume fraction ϕ, permeability parameter K, nonlinear stretching sheet parameter n, magnetic field parameter M, heat generation parameter Q and Eckert number Ec on the flow field, temperature distribution, skin friction and Nusselt number are studied and presented in graphical illustrations and tabular forms. The results obtained reveal that there is an enhancement in the rate of heat transfer with the rise in nanoparticle volume fraction and permeability parameter. The temperature distribution is also influenced with the presence of K, Q, R and ϕ. This shows that the solid volume fraction of nanoparticle can be used in controlling the behaviours of heat transfer and nanofluid flows.
    Matched MeSH terms: Hot Temperature
  6. Fulltext Entropy Generation Analysis and Natural Convection in a Nanofluid-Filled Square Cavity with a Concentric Solid Insert and Different Temperature Distributions
    Alsabery AI, Ishak MS, Chamkha AJ, Hashim I
    Entropy (Basel), 2018 May 03;20(5).
    PMID: 33265426 DOI: 10.3390/e20050336
    The problem of entropy generation analysis and natural convection in a nanofluid square cavity with a concentric solid insert and different temperature distributions is studied numerically by the finite difference method. An isothermal heater is placed on the bottom wall while isothermal cold sources are distributed along the top and side walls of the square cavity. The remainder of these walls are kept adiabatic. Water-based nanofluids with Al 2 O 3 nanoparticles are chosen for the investigation. The governing dimensionless parameters of this study are the nanoparticles volume fraction ( 0 ≤ ϕ ≤ 0.09 ), Rayleigh number ( 10 3 ≤ R a ≤ 10 6 ) , thermal conductivity ratio ( 0.44 ≤ K r ≤ 23.8 ) and length of the inner solid ( 0 ≤ D ≤ 0.7 ). Comparisons with previously experimental and numerical published works verify a very good agreement with the proposed numerical method. Numerical results are presented graphically in the form of streamlines, isotherms and local entropy generation as well as the local and average Nusselt numbers. The obtained results indicate that the thermal conductivity ratio and the inner solid size are excellent control parameters for an optimization of heat transfer and Bejan number within the fully heated and partially cooled square cavity.
    Matched MeSH terms: Hot Temperature
  7. Fulltext Influence of honey types and heating treatment on the rheological properties of glutinous rice flour gels
    Seow EK, Gan CY, Tan TC, Lee LK, Easa AM
    J Food Sci Technol, 2019 Apr;56(4):2105-2114.
    PMID: 30996444 DOI: 10.1007/s13197-019-03691-z
    Present study compared the rheological properties of glutinous rice flour (GRF) gel (33.3%, w/v) added with raw bee honey (RBH) or stingless bee honey (SBH) with/without heating treatment. RBH (diatase activity: 12.14 Schade) and SBH (1.53 Schade) significantly reduced the network of GRF gel by lowering the gel viscosity, with RBH having the highest rate of viscosity decrease (- 2.74 × 10-5 Pa). As the addition of heated-SBH or heated-RBH did not reduce gel viscosity, it was hypothesised that active diastase played a major role to weaken gel network. This was further supported by the significant and the lowest storage modulus (G') value of RBH-GRF gel (5.99 ± 0.02 Pa), as compared to SBH-GRF (6.27 ± 0.04 Pa) and control (6.33 ± 0.04 Pa). A detail of rheological behaviour of the gels was further explained using power law. Overall, this GRF gel model has successfully demonstrated the potential of honey diastase in weakening network of starch-based food.
    Matched MeSH terms: Hot Temperature
  8. Fulltext Elevated-Temperature Performance, Combustibility and Fire Propagation Index of Fly Ash-Metakaolin Blend Geopolymers with Addition of Monoaluminium Phosphate (MAP) and Aluminum Dihydrogen Triphosphate (ATP)
    Zulkifly K, Cheng-Yong H, Yun-Ming L, Bayuaji R, Abdullah MMAB, Ahmad SB, et al.
    Materials (Basel), 2021 Apr 15;14(8).
    PMID: 33920865 DOI: 10.3390/ma14081973
    Thermal performance, combustibility, and fire propagation of fly ash-metakaolin (FA-MK) blended geopolymer with the addition of aluminum triphosphate, ATP (Al(H2PO4)3), and monoaluminium phosphate, MAP (AlPO4) were evaluated in this paper. To prepare the geopolymer mix, fly ash and metakaolin with a ratio of 1:1 were added with ATP and MAP in a range of 0-3% by weight. The fire/heat resistance was evaluated by comparing the residual compressive strengths after the elevated temperature exposure. Besides, combustibility and fire propagation tests were conducted to examine the thermal performance and the applicability of the geopolymers as passive fire protection. Experimental results revealed that the blended geopolymers with 1 wt.% of ATP and MAP exhibited higher compressive strength and denser geopolymer matrix than control geopolymers. The effect of ATP and MAP addition was more obvious in unheated geopolymer and little improvement was observed for geopolymer subjected to elevated temperature. ATP and MAP at 3 wt.% did not help in enhancing the elevated-temperature performance of blended geopolymers. Even so, all blended geopolymers, regardless of the addition of ATP and MAP, were regarded as the noncombustible materials with negligible (0-0.1) fire propagation index.
    Matched MeSH terms: Hot Temperature
  9. A Glimpse into the Extraction Methods of Active Compounds from Plants
    Chuo SC, Nasir HM, Mohd-Setapar SH, Mohamed SF, Ahmad A, Wani WA, et al.
    Crit Rev Anal Chem, 2020 Sep 20.
    PMID: 32954795 DOI: 10.1080/10408347.2020.1820851
    Naturally active compounds are usually contained inside plants and materials thereof. Thus, the extraction of the active compounds from plants needs appropriate extraction methods. The commonly employed extraction methods are mostly based on solid-liquid extraction. Frequently used conventional extraction methods such as maceration, heat-assisted extraction, Soxhlet extraction, and hydrodistillation are often criticized for large solvent consumption and long extraction times. Therefore, many advanced extraction methods incorporating various technologies such as ultrasound, microwaves, high pressure, high voltage, enzyme hydrolysis, innovative solvent systems, adsorption, and mechanical forces have been studied. These advanced extraction methods are often better than conventional methods in terms of higher yields, higher selectivity, lower solvent consumption, shorter processing time, better energy efficiency, and potential to avoid organic solvents. They are usually designed to be greener, more sustainable, and environment friendly. In this review, we have critically described recently developed extraction methods pertaining to obtaining active compounds from plants and materials thereof. Main factors that affect the extraction performances are tuned, and extraction methods are chosen in line with the properties of targeted active compounds or the objectives of extraction. The review also highlights the advancements in extraction procedures by using combinations of extraction methods to obtain high overall yields or high purity extracts.
    Matched MeSH terms: Hot Temperature
  10. Fulltext Morphological and compositional changes exhibited by rice husk when subjected to synergistic thermochemical treatments
    Revathi Rajan, Yusmazura Zakaria, Shaharum Shamsuddin, Nik Fakhuruddin Nik Hassan
    Malaysian Journal of Medicine and Health Sciences, 2020;16(101):1-7.
    MyJurnal
    Introduction: Rice husk has portrayed great potential in becoming a sustainable biomass source in producing silica, cellulose and carbon materials, which garnered widespread interest among researchers. The objective of the current study is to determine the morphological and compositional changes in rice husk due to the synergistic effects of ther- mochemical treatment. Methods: Washed and dried rice husk was blended into a fine powder and then subjected to step-wise heat treatment and acid digestion to produce white ash. The intermittent products, as well as the original rice husk and the final ash product, were characterised using analytical instruments to document the morphologi- cal and chemical composition changes. Results: This report highlights the production of pure rice husk ash using a step-wise treatment using a combination of thermochemical treatment and carbonisation. The results showed that a partial breakdown of the lignocellulose components was achieved using directed thermal treatment at low tem- perature. The ionic impurities were leached out in subsequent heated acid treatment. Thereafter, the carbonaceous organic matter was completely converted to carbon during the carbonisation of the sample and the remaining carbon residue was removed during calcination. High purity ash contained agglomerated and nanostructured silica in the dimensions of 20 to 50 nm in the amorphous form. Conclusion: The step-wise treatment allowed systematic removal of each compound while maintaining the amorphous mineral phase of silica and avoiding carbon fixation. Under- standing the effect of each treatment offers insight to produce purer silica from rice husk.
    Matched MeSH terms: Hot Temperature
  11. A Direct n-Butane Solid Oxide Fuel Cell Using Ba(Zr0.1Ce0.7Y0.1Yb0.1)0.9Ni0.05Ru0.05O3-δ Perovskite as the Reforming Layer
    Wang D, Wong SI, Sunarso J, Xu M, Wang W, Ran R, et al.
    ACS Appl Mater Interfaces, 2021 May 05;13(17):20105-20113.
    PMID: 33886260 DOI: 10.1021/acsami.1c02502
    Hydrocarbon-fueled solid oxide fuel cells (SOFCs) that can operate in the intermediate temperature range of 500-700 °C represent an attractive SOFC device for combined heat and power applications in the industrial market. One of the ways to realize such a device relies upon exploiting an in situ steam reforming process in the anode catalyzed by an anti-carbon coking catalyst. Here, we report a new Ni and Ru bimetal-doped perovskite catalyst, Ba(Zr0.1Ce0.7Y0.1Yb0.1)0.9Ni0.05Ru0.05O3-δ (BZCYYbNRu), with enhanced catalytic hydrogen production activity on n-butane (C4H10), which can resist carbon coking over extended operation durations. Ru in the perovskite lattice inhibits Ni precipitation from perovskite, and the high water adsorption capacity of proton conducting perovskite improves the coking resistance of BZCYYbNRu. When BZCYYbNRu is used as a steam reforming catalyst layer on a Ni-YSZ-supported anode, the single fuel cell not only achieves a higher power density of 1113 mW cm-2 at 700 °C under a 10 mL min-1 C4H10 continuous feed stream at a steam to carbon (H2O/C) ratio of 0.5 but also shows a much better operational stability for 100 h at 600 °C compared with those reported in the literature.
    Matched MeSH terms: Hot Temperature
  12. Unsteady free convection flow between two vertical parallel plates with newtonian heating
    Fasihah Zulkiflee, Ahmad Qushairi Mohamad, Sharidan Shafie, Arshad Khan
    MATEMATIKA, 2019;35(2):117-127.
    MyJurnal
    Free convection flow in a boundary layer region is a motion that results from the interaction of gravity with density differences within a fluid. These differences occur due to temperature or concentration gradients or due to their composition. Studies per- taining free convection flows of incompressible viscous fluids have received much attention in recent years both theoretically (exact or approximate solutions) and experimentally. The situation where the heat be transported to the convective fluid via a bounding sur- face having finite heat capacity is known as Newtonian heating (or conjugate convective flows). In this paper, the unsteady free convection flow of an incompressible viscous fluid between two parallel plates with Newtonian heating is studied. Appropriate non- dimensional variables are used to reduce the dimensional governing equations along with imposed initial and boundary conditions into dimensionless forms. The exact solutions for velocity and temperature are obtained using the Laplace transform technique. The corresponding expressions for skin friction and Nusselt number are also calculated. The graphical results are displayed to illustrate the influence of various embedded parameters such as Newtonian heating parameter and Grashof number. The results show that the effect of Newtonian heating parameter increases the Nusselt number but reduces the skin friction.
    Matched MeSH terms: Hot Temperature
  13. Fulltext Organic Selenium as Antioxidant Additive in Mitigating Acrylamide in Coffee Beans Roasted via Conventional and Superheated Steam
    Alafeef AK, Ariffin F, Zulkurnain M
    Foods, 2020 Aug 29;9(9).
    PMID: 32872507 DOI: 10.3390/foods9091197
    Selenium is an essential micronutrient with significant antioxidant activity promising in mitigating the formation of acrylamide during high-temperature roasting. In this study, green coffee beans pretreated with selenium (Se-coffee) were investigated on their selenium uptake, selenium retention in green and roasted beans, antioxidant activities, and formation of acrylamide during conventional and superheated steam roasting. Comparisons were made with positive (pretreated without selenium) and negative (untreated) controls. The acrylamide formation was significantly inhibited in Se-coffee (108.9-165.3 μg/kg) compared to the positive and negative controls by 73.9% and 52.8%, respectively. The reduction of acrylamide by superheated steam roasting only observed in the untreated coffee beans (negative control) by 32.4% parallel to the increase in its antioxidant activity. Selenium pretreatment significantly increased antioxidant activity of the roasted Se-coffee beans after roasting although soaking pretreatment significantly reduced antioxidant activity in the green beans. Acrylamide reduction in the roasted coffee beans strongly correlated with the change in antioxidant capacities after roasting (∆FRAP, 0.858; ∆DPPH, 0.836). The results indicate that the antioxidant properties of the organic selenium suppressed acrylamide formation during coffee roasting.
    Matched MeSH terms: Hot Temperature
  14. Vaccination of chickens against Newcastle disease with a food pellet vaccine
    Ideris A, Ibrahim AL, Spradbrow PB
    Avian Pathol, 1990 Apr;19(2):371-84.
    PMID: 18679945
    The Australian, heat-resistant, a virulent V4 strain of Newcastle disease (ND) virus was selected for further heat resistance to give a variant designated V4-UPM. V4-UPM was sprayed on to food pellets which were fed to chickens in amounts calculated to give about 10(6) EID50 per chicken. Chickens vaccinated only once by feeding developed no haemagglutination-inhibition (HI) antibodies and were not protected against challenge with a viscerotropic velogenic strain of ND virus. Chickens given food pellet vaccine at 3 and 6 weeks of age developed HI antibodies and were substantially protected against parenteral and contact challenge with virulent ND virus. Similar protection was achieved when the V4-UPM vaccine was given intranasally on two occasions or when the vaccine virus was allowed to spread by contact from intranasally vaccinated chickens to nonvaccinated chickens. Heat resistant ND vaccine incorporated in food pellets may provide a method for protecting village chickens against ND in tropical countries.
    Matched MeSH terms: Hot Temperature
  15. Quantitative comparisons of lung structure of adult domestic fowl and red jungle fowl, with reference to broiler ascites
    Vidyadaran MK, King AS, Kassim H
    Avian Pathol, 1990 Jan;19(1):51-8.
    PMID: 18679913
    A stereological comparison has been made of the structure of the lungs of the adult female domestic fowl and its wild progenitor the Red Jungle Fowl. The volume of the lung per unit body weight of the domestic bird is between 20 and 33% smaller than that of the wild bird. The domestic fowl has partly compensated for this by increasing the surface area for gas exchange per unit volume of exchange tissue. However, the blood-gas tissue barrier is about 28% thicker in the domestic fowl than in the Red Jungle Fowl, and this has led to a 25% lower anatomical diffusing capacity for oxygen of the blood-gas tissue barrier per unit body weight in the domestic fowl. These structural characteristics may make the modern domestic fowl vulnerable to stress factors such as altitude, cold, heat or air pollution by predisposing to hypoxaemia and perhaps thence to ascites.
    Matched MeSH terms: Hot Temperature
  16. Processing of coconut sap into sugar syrup using rotary evaporation, microwave, and open-heat evaporation techniques
    Asghar MT, Yusof YA, Mokhtar MN, Yaacob ME, Ghazali HM, Varith J, et al.
    J Sci Food Agric, 2020 Aug;100(10):4012-4019.
    PMID: 32337729 DOI: 10.1002/jsfa.10446
    BACKGROUND: Coconut sugar has a caramel color with a taste like brown sugar. It is commonly used as natural sweetener. However, coconut sugar has been produced from coconut sap using a traditional method that involves heating the sap at high temperature (>100 °C) in an open pan for a long period (3-5 h). This conventional method results in an over-cooked sugar, which leads to quality deterioration in terms of both its physical and chemical properties. The current study aimed to investigate the processing of coconut sap into sugar syrup using alternative processing techniques such as rotary vacuum evaporation (RE) and microwave evaporation (ME), comparing them with open-heat evaporation (OHE) technique.

    RESULTS: Coconut sugar syrup produced by rotary evaporation at 60 °C and 250 mbar vacuum (RE-60) required the shortest production time (12.2 min) and the lowest processing temperature (54.8 °C) when compared with ME (13 min and 103.2 °C) and OHE (46.8 min and 101.6 °C). It also had a light brownish color with a higher L* value (35.17) than the ME (29.84) and OHE (23.84) methods. It was found to contain higher amounts of monosaccharides (fructose and glucose) and lower amounts of disaccharides (sucrose). Furthermore, the amount of energy required for RE-60 (0.35 kWh) was much less than for OHE (0.83 kWh).

    CONCLUSION: This study provided an alternative processing method for the sugar processing industry to produce coconut sugar using the rotary evaporation method at 60 °C under 250 mbar vacuum with better physicochemical qualities, shorter processing time, and minimum input energy. © 2020 Society of Chemical Industry.

    Matched MeSH terms: Hot Temperature
  17. Fulltext Optimization of spray drying parameters for pink guava powder using RSM
    Islam Shishir MR, Taip FS, Aziz NA, Talib RA, Hossain Sarker MS
    Food Sci Biotechnol, 2016;25(2):461-468.
    PMID: 30263292 DOI: 10.1007/s10068-016-0064-0
    The optimization of pink guava was executed using central composite face-centred design to optimize the spray drying parameters of inlet temperature, maltodextrin concentration (MDC) and feed flow (FF). The experimental results were significantly (p<0.01) fitted into second-order polynomial models to describe and predict the response quality in terms of the final moisture, particle size and lycopene with R2 of 0.9749, 0.9616, and 0.9505, respectively. The final moisture content significantly (p<0.01) decreased with increasing inlet temperature and MDC, whereas the particle size increased. In contrast, the lycopene content significantly (p<0.01) decreased with the higher temperature and increased with increasing MDC. However, according to multiple response optimization, the optimum conditions of 150°C inlet temperature, 17.12% (w/v) MDC and 350 mL/h FF-predicted 3.10% moisture content, 11.23 μm particle size and 58.71 mg/100 g lycopene content. The experimental observation satisfied the predicted model within the acceptable range of the responses.
    Matched MeSH terms: Hot Temperature
  18. Fulltext Development of Porous Epoxy Micro-Beads Using Ammonium Bicarbonate through a Single Epoxy Droplet in Corn Oil
    Leemsuthep A, Zakaria Z, Tanrattanakul V, Ramarad S, Muniyadi M, Jaruga T, et al.
    Materials (Basel), 2021 Apr 28;14(9).
    PMID: 33924997 DOI: 10.3390/ma14092282
    This paper explored the effects of ammonium bicarbonate and different ratios of epoxy to polyamide on the formation of porous epoxy micro-beads through a single epoxy droplet. A single drop of a mixture, consisting of epoxy, polyamide, and ammonium bicarbonate, was dropped into heated corn oil at a temperature of 100 °C. An epoxy droplet was formed due to the immiscibility of the epoxy mixture and corn oil. The ammonium bicarbonate within this droplet underwent a decomposition reaction, while the epoxy and polyamide underwent a curing reaction, to form porous epoxy micro-beads. The result showed that the higher ammonium bicarbonate content in the porous, epoxy micro-beads increased the decomposition rate up to 11.52 × 10-3 cm3/s. In addition, a higher total volume of gas was generated when a higher ammonium bicarbonate content was decomposed. This led to the formation of porous epoxy micro-beads with a smaller particle size, lower specific gravity, and better thermal stability. At an epoxy to polyamide ratio of 10:6, many smaller micro-beads, with particle sizes ranging from 201 to 400 μm, were obtained at an ammonium bicarbonate content of 10 phr. Moreover, the porous epoxy micro-beads with open pores were shown to have a low specific gravity of about 0.93 and high thermal stability at a high ammonium bicarbonate content. Based on the findings, it was concluded that porous epoxy micro-beads were successfully produced using a single epoxy droplet in heated corn oil, where their shape and particle size depended on the content of ammonium bicarbonate and the ratio of epoxy to polyamide used.
    Matched MeSH terms: Hot Temperature
  19. Fulltext An Exploratory Study on Resistance Spot Welding of Titanium Alloy Ti-6Al-4V
    Fatmahardi I, Mustapha M, Ahmad A, Derman MN, Lenggo Ginta T, Taufiqurrahman I
    Materials (Basel), 2021 Apr 30;14(9).
    PMID: 33946335 DOI: 10.3390/ma14092336
    Resistance spot welding (RSW) is one of the most effective welding methods for titanium alloys, in particular Ti-6Al-4V. Ti-6Al-4V is one of the most used materials with its good ductility, high strength, weldability, corrosion resistance, and heat resistance. RSW and Ti-6Al-4V materials are often widely used in industrial manufacturing, particularly in automotive and aerospace industries. To understand the phenomenon of resistance spot weld quality, the physical and mechanical properties of Ti-6Al-4V spot weld are essential to be analyzed. In this study, an experiment was conducted using the Taguchi L9 method to find out the optimum level of the weld joint strength. The given optimum level sample was analyzed to study the most significant affecting RSW parameter, the failure mode, the weld nugget microstructure, and hardness values. The high heat input significantly affect the weld nugget temperature to reach and beyond the β-transus temperature. It led to an increase in the weld nugget diameter and the indentation depth. The expulsion appeared in the high heat input and decreased the weld nugget strength. It was caused by the molten material ejection in the fusion zone. The combination of high heat input and rapid air cooling at room temperature generated a martensite microstructure in the fusion zone. It increased the hardness, strength, and brittleness but decreased the ductility.
    Matched MeSH terms: Hot Temperature
  20. Fulltext Fabrication and Thermo-Electro and Mechanical Properties Evaluation of Helical Multiwall Carbon Nanotube-Carbon Fiber/Epoxy Composite Laminates
    Ali A, Andriyana A, Hassan SBA, Ang BC
    Polymers (Basel), 2021 Apr 29;13(9).
    PMID: 33947012 DOI: 10.3390/polym13091437
    The development of advanced composite materials has taken center stage because of its advantages over traditional materials. Recently, carbon-based advanced additives have shown promising results in the development of advanced polymer composites. The inter- and intra-laminar fracture toughness in modes I and II, along with the thermal and electrical conductivities, were investigated. The HMWCNTs/epoxy composite was prepared using a multi-dispersion method, followed by uniform coating at the mid-layers of the CF/E prepregs interface using the spray coating technique. Analysis methods, such as double cantilever beam (DCB) and end notched flexure (ENF) tests, were carried out to study the mode I and II fracture toughness. The surface morphology of the composite was analyzed using field emission scanning electron microscopy (FESEM). The DCB test showed that the fracture toughness of the 0.2 wt.% and 0.4 wt.% HMWCNT composite laminates was improved by 39.15% and 115.05%, respectively, compared with the control sample. Furthermore, the ENF test showed that the mode II interlaminar fracture toughness for the composite laminate increased by 50.88% and 190%, respectively. The FESEM morphology results confirmed the HMWCNTs bridging at the fracture zones of the CF/E composite and the improved interlaminar fracture toughness. The thermogravimetric analysis (TGA) results demonstrated a strong intermolecular bonding between the epoxy and HMWCNTs, resulting in an improved thermal stability. Moreover, the differential scanning calorimetry (DSC) results confirmed that the addition of HMWCNT shifted the Tg to a higher temperature. An electrical conductivity study demonstrated that a higher CNT concentration in the composite laminate resulted in a higher conductivity improvement. This study confirmed that the demonstrated dispersion technique could create composite laminates with a strong interfacial bond interaction between the epoxy and HMWCNT, and thus improve their properties.
    Matched MeSH terms: Hot Temperature
Related Terms
Filters
Contact Us

Please provide feedback to Administrator (afdal@afpm.org.my)

External Links