Displaying publications 21 - 33 of 33 in total

Abstract:
Sort:
  1. Fulltext Effects of Starter Defect on Energy Release Rate of Three-Point End-Notch Flexure Tested Unidirectional Carbon Fiber Reinforced Polymer Composite
    Nor FM, Lim JY, Tamin MN, Lee HY, Kurniawan D
    Polymers (Basel), 2020 Apr 14;12(4).
    PMID: 32295111 DOI: 10.3390/polym12040904
    The mechanics of damage and fracture process in unidirectional carbon fiber reinforced polymer (CFRP) composites subjected to shear loading (Mode II) were examined using the experimental method of the three-point end-notch flexure (3ENF) test. The CFRP composite consists of [0o]16 with an insert film in the middle plane for a starter defect. A 3ENF test sample with a span of 50 mm and interface delamination crack length of 12.5 mm was tested to yield the load vs. deformation response. A sudden load drop observed at maximum force value indicates the onset of delamination crack propagation. The results are used to extract the energy release rate, GIIC, of the laminates with an insert film starter defect. The effect of the starter defect on the magnitude of GIIC was examined using the CFRP composite sample with a Mode II delamination pre-crack. The higher magnitude of GIIC for the sample with insert film starter defect was attributed to the initial straight geometry of the notch/interface crack and the toughness of the resin at the notch front of the fabricated film insert. The fractured sample was examined using a micro-computerized tomography scanner to establish the shape of the internal delamination crack front. Results revealed that the interface delamination propagated in a non-uniform manner, leaving a curved-shaped crack profile.
    Matched MeSH terms: Resins, Plant
  2. Effect of phosphite loading on the mechanical and fire properties of palm-based polyurethane
    Khairiah Badri, Amamer Musbah Redwan
    Sains Malaysiana, 2010;39.
    Fire-retarding polyurethane (PU) composite was produced by adding 2,4-ditert-butylphenyl phosphite (FR) to palm-based monoester resin with loading percentage of 0, 2, 4, and 6 wt%. The Shore D hardness index increased marginally with increasing FR content. However, the impact and flexural strengths decreased with increasing FR loading attributed to the weak interfacial bonding between FR and PU matrix. The fire test indicated lowering of burning rate (from 5.30 mm.s-1 to 2.80 mm.s-1) as the loading percentage of FR increased. The combustion enthalpy of the composites also decreased with higher loading percentage of FR.
    Matched MeSH terms: Resins, Plant
  3. Effect of aluminum hydroxide loading on the compression stress and modulus, thermal conductivity and acoustic properties of palm-based polyurethane hybrid composite
    Nor Rabbi’atul ‘Adawiyah Norzali, Khairiah Badri, Mohd Zaki Nuawi
    Sains Malaysiana, 2011;40.
    The effect of adding aluminum hydroxide (ATH) in the palm-based polyurethane hybrid composite was studied. The compression stress and modulus, thermal conductivity and acoustic property were determined. The hybrid composite was prepared by adding 10 wt% of oil palm empty fruit bunch fibre (EFB) followed by ATH at varying amount of 2, 4 and 6 wt% of the overall mass of the resin. The compression stress and modulus gave the highest values of 575 kPa and 2301 kPa, respectively at 2 wt% ATH. At 4 wt% ATH, the compression stress and modulus decreased to 431 kPa and 1659 kPa, respectively and further decreased at 6 wt% ATH to 339 kPa and 1468 kPa respectively. The k-value increased with the increment of the ATH loading exhibited a poor thermal conductivity. Sound absorption analysis indicated that the absorption coefficient was higher at higher frequency (4000 Hz) for all samples with PU-EFB/ATH with 4% ATH showed the highest absorption coefficient.
    Matched MeSH terms: Resins, Plant
  4. Fulltext Datasets of essential oils from naturally formed and synthetically induced Aquilaria malaccensis agarwoods
    Abdul Kadir FA, Azizan KA, Othman R
    Data Brief, 2020 Feb;28:104987.
    PMID: 32226799 DOI: 10.1016/j.dib.2019.104987
    Agarwood is the highly valuable fragrant resin of the wounded Aquilaria spp. trees widely used in fragrances, medicines and incenses. Among the Aquilaria spp., A. malaccensis is the primary producer and is mainly found in Indonesia and Malaysia. In normal condition, agarwood is naturally formed in Aquilaria trees as a defense mechanism upon physical damage or microbial infection on the trees, which is a slow process that occurs over several years. The high demand in agarwood has spurred the development of various artificial inoculation methods where agarwood formation is synthetically induced in a shorter period of time. However, the synthetic induction method produces agarwood with aromas different from the naturally formed agarwood. To understand the changes in the agarwoods produced from different induction conditions, metabolite profiling of agarwood essential oil from A. malaccensis has been performed. The essential oils of healthy undamaged tree trunks and, naturally formed and synthetically induced agarwoods were obtained using hydrodistillation (HS) method and analysed using gas chromatography mass spectrometer (GC-MS). These data will provide valuable resources for chemical components of agarwood produced by the species in the genus Aquilaria.
    Matched MeSH terms: Resins, Plant
  5. Fulltext Comparison of Flexural Strength of Kevlar, Glass, and Nylon Fibers Reinforced Denture Base Resins With Heat Polymerized Denture Base Resins
    Kannaiyan K, Biradar Sharashchandra M, Kattimani S, Devi M, Vengal Rao B, Kumar Chinna S
    J Pharm Bioallied Sci, 2020 Aug;12(Suppl 1):S399-S403.
    PMID: 33149494 DOI: 10.4103/jpbs.JPBS_117_20
    Introduction: Polymethyl methacrylate (PMMA) has been widely accepted and used in dentistry owing to its working characteristics, aesthetics and stability in the oral environment, ease in manipulation, and inexpensive processing methods and equipment.

    Aim and Objectives: The aim of this study was to evaluate the flexural strength of a high-impact PMMA denture base resin material and flexural strength of a commonly available heat cure PMMA denture base material with Kevlar, glass, and nylon fibers.

    Materials and Methods: The test samples were studied under two groups. The Group I (control group) comprised pre-reinforced PMMA (Lucitone 199; Dentsply Sirona Prosthetics, York, Pennsylvania, USA) consisting of 12 samples and second group comprised regular PMMA (DPI, Mumbai, India) reinforced with different fibers. The second test group was further divided into three subgroups as Group 2, Group 3, and Group 4 comprising 12 samples each designated by the letters a-l. All the samples were marked on both ends. A total of 48 samples were tested. Results were analyzed and any P value ≤0.05 was considered as statistically significant (t test).

    Results: All the 48 specimens were subjected to a 3-point bending test on a universal testing machine (MultiTest 10-i, Sterling, VA, USA) at a cross-head rate of 2 mm/min. A load was applied on each specimen by a centrally located rod until fracture occurred; span length taken was 50 mm. Flexural strength was then calculated.

    Conclusion: Reinforcement of conventional denture base resin with nylon and glass fibers showed statistical significance in the flexural strength values when compared to unreinforced high impact of denture base resin.

    Matched MeSH terms: Resins, Plant
  6. Fulltext Colour vision of workers in the plastics industry
    Kaur S, Mursyid A, Ariffin AE
    Journal of Occupational Safety and Health, 2004;1(1):25-30.
    MyJurnal
    A study was undertaken to determine the effect of polyethylene and polystyrene used in the manufacture of plastic items on colour perception. Colour vision was assessed using the Ishihara plates, panel 015 test and the Farnsworth Munsell 100-Hue test. Two factories were chosen at random. One factory (referred here as factory A) used virgin resin in pellet form (polyethylene) in the manufacturing of plastic containers to store consumer edible oil. The other factory (referred as factory B) used polystyrene to make plastic bags. A total of 39 healthy employees from factory A (mean age 26.4 :t 8.2 years) and 40 healthy employees from factory B (mean age 26.8 :t 9.6 years) were recruited in this study. A control group of 27 normal healthy subjects (mean age 27.4 :t 4.3 years) who were employees of UKM with no occupational involvement with petroleum derivatives were also recruited in this study and they performed the same colour vision tests. All subjects passed the Ishihara plates test showing that none of the subjects (employees of factory A and B, and control subjects) had a congenital red-green defect. All control subjects passed all of the colour vision tests whilst some employees of factories A and B failed the 015 and FM100 Hue tests. For employees from factory A results from the 015 test showed that 7 (17.9%) had a tritan (blue-yellow) type of defect and 1 (2.6%) had a complex type of defect. The FM 100 Hue results of factory A employees showed that 51.3% (n=20) had a complex type of defect. Total error scores (TES) calculated from the FM 100 Hue test revealed that employees from factory A had a statistically significant higher mean TES of 65.13:!: 48.31 compared to that of control subjects with a mean TES of 31.26:!: 14.93. For employees in factory B, 10 employees (25.0%) had a tritan (blue-yellow) type of defect and 2 (5.0%) had a complex type of defect. Results of the FM 100 Hue test showed that 4 employees (1.0%) had a tritan type of defect whereas 22 (55.0%) had a complex type of defect. Mean total error scores (TES) calculated from the FM 100 Hue test revealed that employees from factory B had a statistically significant higher mean TES of 71.54 :t 54.63 compared with that of control subjects with a mean TES of 31.26 :t. 14.93

    The above results show that employees of the plastic factories studies are associated with a higher risk of acquiring colour vision defects as compared to normal subjects who are not engaged in the plastic manufacturing industry. This may have an implication towards the future retinal health of employees in petrod1emical-based industries.
    Matched MeSH terms: Resins, Plant
  7. Fulltext Bond strengths of composite resins used for the attachment of bonded retainers
    Sinniah, Saraswathy D., Jones, Steven P., Georgiou, George, Cunningham, Susan J., Petrie, Aviva
    Compendium of Oral Science, 2016;3(1):17-24.
    MyJurnal
    used with bonded retainers. Setting: Department of Orthodontics, UCL Eastman Dental Institute, United Kingdom. Methods: Flowable composite resins (Transbond TM Supreme LV, StarFlowTM and Tetric EvoFlow®) and non -flowable control resin (TransbondTM LR) were made into cylinders prior to bonding to hydoxyapatite discs. They were then mounted into jigs and tested in the InstronTM Universal Testing Machine in both shear and tensile modes. Results: The highest mean shear bond strength was seen with StarFlow TM (14.09 MPa), which was significantly higher than both TransbondTM LR (9.48 MPa) and TransbondTM Supreme LV (8.20 MPa). The mean shear bond strength of Tetric EvoFlow® (11.86 MPa) was also significantly higher than TransbondTM Supreme LV. The highest mean tensile bond strength was seen with Tetric EvoFlow® (2.14 MPa), which was significantly higher than TransbondTM LR (1.15 MPa) and TransbondTM Supreme LV (0.61 MPa) but not significantly different to StarFlowTM (1.47 MPa). For shear loading, StarFlowTM had the highest 50th percentile survival estimate at 15.10 MPa, followed by Tetric EvoFlow® (13.00 MPa) and TransbondTM Supreme LV (7.50 MPa). TransbondTM LR had a 50th percentile estimate at 9.00 MPa. For tensile loading, Tetric EvoFlow® had the highest 50th percentile survival estimate at 2.50 MPa, followed by StarFlowTM (1.30 MPa) and TransbondTM Supreme LV (0.50 MPa). TransbondTM LR had a 50th percentile estimate at 1.00 MPa. Conclusions: Mean shear bond strengths for all of the resins were significantly higher than the mean tensile bond strengths. StarFlowTM and Tetric EvoFlow® could potentially be suitable clinical alternatives to TransbondTM LR due to its low viscosity flow characteristics and adequate shear and tensile bond strengths.
    Matched MeSH terms: Resins, Plant
  8. Blends of LNR with unsaturated polyester resin from recycled PET: comparison of mechanical properties and morphological analysis with the optimum blend by commercial resin
    Siti Farhana Hisham, Ishak Ahmad, Rusli Daik, Anita Ramli
    Sains Malaysiana, 2011;40:1179-1186.
    In this study, poly(ethylene terephthalate) (PET) wastes bottle was recycled by glycolysis process using ethylene glycol. The unsaturated polyester resin (UPR) was then prepared by reacting the glycolysed product with maleic anhydride. The blend of UPR based on recycled PET wastes with liquid natural rubber (LNR) was carried out by varying the amount of LNR from 0 to 7.5 wt%. Mechanical tests such as tensile and impact were conducted to investigate the effects of LNR on the mechanical properties. Scanning Electron Microscopy (SEM) was used to analyze the morphology of the breaking area resulted from the tensile tests on the UPR and blend samples. From the results, the blend of 2.5 wt% LNR in UPR based recycled PET wastes achieved the highest strength in the mechanical properties and showed a well dispersed of elastomer particles in the sample morphology compared to other blends concentrations. This blend sample was then compared to the optimum blend of LNR with commercial resin through the glass transition temperature value Tg, mechanical strength and morphology properties. The comparison study showed that the Tg for UPR based recycled PET was higher than the value represented from commercial resin due to the degree of crystalinity in the molecular structure of the materials. LNR was found to be an effective impact modifier which gave a greater improvement in UPR from recycled PET wastes structure but not to the commercial one which needs 5% LNR to achieve the optimum properties. Thus, the compatibility between the UP resin based recycled PET and LNR was much better than with the commercial resin.
    Matched MeSH terms: Resins, Plant
  9. As-spun bio-novolac fibre morphological study based on resin’s physico-chemical properties
    Siti Noorul Aina Ab Rahim, Sarani Zakaria, Sharifah Nabihah Syed Jaafar, Chin HC, Rasidi Roslan, Hatika Kaco, et al.
    Sains Malaysiana, 2017;46:1659-1665.
    Bio-novolac fibre made from phenol-formaldehyde derived oil palm empty fruit bunch (EFB) was produced using electrospinning method. The bio-novolac phenol-formaldehyde was prepared via liquefaction and resinification at two different molar ratios of formaldehyde to liquefied EFB (LEFB) (F:LEFB = 0.5:1 and 0.8:1). Electrospinning was applied to the bio-novolac phenol-formaldehyde (BPF) in order to form smooth and thin as-spun fibre. The BPF was electrospun at 15 kV and 15 cm distance between needle and collector at a flow rate of 0.5 mL/h. At lower molecular weight of BPF resin, beads formation was observed. The addition of poly(vinyl) butyral (Mw = 175,000 - 250,000) has improved the fibre formation with lesser beads hence produced more fibre. Polymer solution with higher molecular weight produced better quality fibre.
    Matched MeSH terms: Resins, Plant
  10. Archaeological resinous samples from Asian wrecks: Taxonomic characterization by GC-MS
    Burger P, Charrié-Duhaut A, Connan J, Flecker M, Albrecht P
    Anal Chim Acta, 2009 Aug 19;648(1):85-97.
    PMID: 19616693 DOI: 10.1016/j.aca.2009.06.022
    Plant resins, and particularly dammars from the Dipterocarpaceae family, were widely used in the past, notably as part of caulking material. The organic composition of resins, already complicated, is not always preserved over time and can be considerably affected by ageing. Hence, their occurrence in archaeological items leads to the necessity to identify them taxonomically with precision. Resinous organic materials collected near and/or on wrecks discovered in South China Sea, supposed to contain dammar resins because of their geographical excavation context, were investigated by gas chromatography-mass spectrometry (GC-MS), together with freshly collected dammars, to establish taxonomic and alteration parameters allowing to identify dammar even in very altered samples or in mixtures together with other organic materials. This study specially focuses on three samples collected within or close to the M1J wreck, a Portuguese wreck lost in the Straight of Malacca during the 16th century. Our analyses establish that all three are made of dammar, two of them in association with pitch and bitumen. In addition, biodegradation biomarkers were detected in all these three samples, indicating that they were submitted to microbial degradation processes during their ageing.
    Matched MeSH terms: Resins, Plant/chemistry*
  11. Antinociceptive and antiinflammatory activities of the aqueous extract of Trigonopleura malayana resin in experimental animal models
    Sulaiman MR, Zakaria ZA, Kamaruddin A, Meng TF, Ali DI, Moin S
    Methods Find Exp Clin Pharmacol, 2008 Nov;30(9):691-6.
    PMID: 19229377 DOI: 10.1358/mf.2008.30.9.1305824
    Trigonopleura malayana L. (Euphorbiaceae) resin, locally known as Gambir Sarawak, has been used traditionally to alleviate pain associated with insect bites, muscle ache, toothache and minor injuries. The present study was carried out using various animal models to determine the antinociceptive and antiinflammatory activities of the T. malayana resin aqueous extract. Antinociceptive activity was measured using the abdominal constriction, hot plate and formalin tests, while antiinflammatory activity was measured using the carrageenan-induced paw edema test. The extract, obtained after 24 h of soaking the dried resin in distilled water, was prepared in doses of 0.3, 3 and 10 mg/kg and administered subcutaneously 30 min prior to the assays. The mechanism of action was also determined by prechallenging with naloxone (10 mg/kg), a nonselective opioid antagonist. The extract was found to exhibit significant (P < 0.05) and dose-dependent antinociceptive and antiinflammatory activities; naloxone failed to inhibit the former activity. In conclusion, the aqueous extract of T. malayana resin possesses nonopioid antinociceptive and antiinflammatory activities, thus supporting previous claims regarding its traditional use by the Malays to treat various ailments, particularly those related to pain.
    Matched MeSH terms: Resins, Plant/chemistry
  12. Adsorption and desorption characteristics of flavonoids from white tea using macroporous adsorption resin
    Yang Y, Liang Q, Zhang B, Zhang J, Fan L, Kang J, et al.
    J Chromatogr A, 2024 Jan 25;1715:464621.
    PMID: 38198876 DOI: 10.1016/j.chroma.2023.464621
    White tea contains the highest flavonoids compared to other teas. While there have been numerous studies on the components of different tea varieties, research explicitly focusing on the flavonoid content of white tea remains scarce, making the need for a good flavonoid purification process for white tea even more important. This study compared the adsorption and desorption performance of five types of macroporous resins: D101, HP20, HPD500, DM301, and AB-8. Among the tested resins, AB-8 was selected based on its best adsorption and desorption performance to investigate the static adsorption kinetics and dynamic adsorption-desorption purification of white tea flavonoids. The optimal purification process was determined: adsorption temperature 25 °C, crude tea flavonoid extract pH 3, ethanol concentration 80 %, sample loading flow rate and eluent flow rate 1.5 BV/min, and eluent dosage 40 BV. The results indicated that the adsorption process followed pseudo-second-order kinetics. Under the above purification conditions, the purity of the total flavonoids in the purified white tea flavonoid increased from approximately 17.69 to 46.23 %, achieving a 2.61-fold improvement, indicating good purification results. The purified white tea flavonoid can be further used for nutraceutical and pharmaceutical applications.
    Matched MeSH terms: Resins, Plant
  13. Fulltext Acute and sub-acute oral toxicity of Dracaena cinnabari resin methanol extract in rats
    Al-Afifi NA, Alabsi AM, Bakri MM, Ramanathan A
    BMC Complement Altern Med, 2018 Feb 05;18(1):50.
    PMID: 29402248 DOI: 10.1186/s12906-018-2110-3
    BACKGROUND: Dracaena cinnabari (DC) is a perennial tree that located on the Southern coast of Yemen native to the Socotra Island. This tree produces a deep red resin known as the Dragon's blood, the Twobrother's Blood or Damm Alakhwain. The current study performed to evaluate the safety of the DC resin methanol extract after a single or 28 consecutive daily oral administrations.

    METHODS: In assessing the safety of DC resin methanol extract, acute and sub-acute oral toxicity tests performed following OECD guidelines 423 and 407, respectively, with slight modifications. In acute oral toxicity test, DC resin methanol extract administered to female Sprague Dawley rats by oral gavage at a single dose of 300 and 2000 mg/kg body weight. Rats observed for toxic signs for 14 days. In sub-acute oral toxicity test, DC resin methanol extract administered to the rats by oral gavage at 500, 1000, and 1500 mg/kg body weight daily up to 28 days to male and female Spradgue Dawley rats. The control and high dose in satellite groups were also maintained and handled as the previous groups to determine the late onset toxicity of DC resin methanol extract. At the end of each test, hematological and biochemical analysis of the collected blood were performed as well as gross and microscopic pathology.

    RESULTS: In acute oral toxicity, no treatment-related death or toxic signs were observed. It revealed that the DC resin methanol extract could be well tolerated up to the dose 2000 mg/kg body weight and could be classified as Category 5. The sub-acute test observations indicated that there are no treatment-related changes up to the high dose level compared to the control. Food consumption, body weight, organ weight, hematological parameters, biochemical parameters and histopathological examination (liver, kidney, heart, spleen and lung) revealed no abnormalities. Water intake was significantly higher in the DC resin methanol extract treated groups compared to the control.

    CONCLUSION: This study demonstrates tolerability of DC resin methanol extract administered daily for 28 days up to 1500 mg/kg dose.

    Matched MeSH terms: Resins, Plant/administration & dosage; Resins, Plant/toxicity*
Related Terms
Filters
Contact Us

Please provide feedback to Administrator (afdal@afpm.org.my)

External Links