The rapid generation rate of solid waste is due to the increasing population and industrialization. Nowadays, solid waste has been a major concerning problem in handling and disposal thus adsorption treatment process has been introduced which is an effective and low-cost method in removing organic and inorganic compounds from leachates such as chemical oxygen demand (COD) and ammoniacal nitrogen (NH3-N). A most commonly adsorbent used for the removal of organic and inorganic compounds is activated carbon (AC), yet the main disadvantage is being too expensive in cost. Many researchers tried to use low-cost adsorbent waste materials, such as peat soil, limestone etc. This review article reveals a list of low-cost adsorbent and their capacity of adsorption for the removal of COD and NH3-N. Furthermore, the preparation of these low-cost adsorbents as well as their removal efficiencies, relative cost, and limitation are discussed. The most efficient, cost-effective, and environment-friendly adsorbent can be used for the removal of COD and NH3-N thus can be provided for commercial usage or water treatment plant.Implications: The concentration of organic constituents (COD) and ammonia nitrogen in stabilized landfill leachate has significant strong influences of human health and environmental. This review article shows the list of low-cost adsorbent (i.e., Activated carbon, Peat soil, Zeolite, Limestone, and cockle shell and their capacity of adsorption for the removal of COD and ammonia nitrogen. This would be greatly applicable in future research era as well as conventionally minimizing high-cost materials use and thereby lowering the operating cost of leachate wastewater treatment.
The SARS-CoV-2 virus has spread globally and has severely impacted public health and the economy. Hand hygiene, social distancing, and the usage of personal protective equipment are considered the most vital tools in controlling the primary transmission of the virus. Converging evidence indicated the presence of SARS-CoV-2 in wastewater and its persistence over several days, which may create secondary transmission of the virus via waterborne and wastewater pathways. Although, researchers have started focusing on this mode of virus transmission, limited knowledge and societal unawareness of the transmission through wastewater may lead to significant increases in the number of positive cases. To emphasize the severe issue of virus transmission through wastewater and create societal awareness, we present a state of the art critical review on transmission of SARS-CoV-2 in wastewater and the potential remedial strategies to effectively control the viral spread and safeguard society. For low-income countries with high population densities, it is suggested to identify the virus in large scale municipal wastewater plants before following up with one-to-one testing for effective control of the secondary transmission. Ultrafiltration is an effective method for wastewater treatment and usually more than 4 logs of virus removal are achieved while safeguarding good protein permeability. Decentralized wastewater treatment facilities using solar-assisted disinfestation methods are most economical and can be effectively used in hospitals, isolation wards, and medical centers for reducing the risk of transmission from high local concentration sites, especially in tropical countries with abundant solar energy. Disinfection with chlorine, sodium hypochlorite, benzalkonium chloride, and peracetic acid have shown potential in terms of virucidal properties. Biological wastewater treatment using micro-algae will be highly effective in removal of virus and can be incorporated into membrane bio-reaction to achieve excellent virus removal rate. Though promising results have been shown by initial research for inactivation of SARS-CoV-2 in wastewater using physical, chemical and biological based treatment methods, there is a pressing need for extensive investigation of COVID-19 specific disinfectants with appropriate concentrations, their environmental implications, and regular monitoring of transmission. Effective wastewater treatment methods with high virus removal capacity and low treatment costs should be selected to control the virus spread and safeguard society from this deadly virus.
This research aims to evaluate the performance of PolyCera® Titan membrane for different wastewater treatment. Membrane filtration of several cycles was conducted in understanding the fouling mechanism, fouling propensity, and defouling potential of the PolyCera® Titan which had not been studied by any other researcher before. The PolyCera® Titan membrane is effective for the treatment of textile industry wastewater, palm oil mill effluent (POME), leachate, and semiconductor-industry wastewater. Rejection of methylene blue (MB) and Congo red (CR) was in the range of 78.76-86.04% and 88.89-93.71%, respectively; 94.72-96.50% NaCl, 96.07-97.62% kaolin, and 97.26-97.73% glucose were rejected from synthetic leachate indicating the removal of TDS, TSS, and COD from the leachate, respectively. Standard blocking and complete model were the best models used to explain the PolyCera® Titan membrane fouling mechanism in all types of wastewater treatment processes with a high R2 value. Physical cleaning with the use of distilled water was able to recover the permeate flux with the flux recovery ratio (FRR) value in the range of 79.2-95.22% in the first cycle, 81.20-98.16% in the second cycle, and 86.09-95.96% in the third cycle.
This work discusses the preparation and characterizations of glass hollow fiber membranes prepared using zeolite-5A as a starting material. Zeolite was formed into a hollow fiber configuration using the phase inversion technique. It was later sintered at high temperatures to burn off organic materials and change the zeolite into glass membrane. A preliminary study, that used thermogravimetric analysis (TGA), X-ray diffraction (XRD), and Fourier transform infrared (FTIR), confirmed that zeolite used in this study changed to glass at temperatures above 1000 °C. The glass hollow fiber membranes prepared using the phase inversion technique has three different microstructures, namely (i) sandwich-like structure that originates from inner layer, (ii) sandwich-like that originates from outer layer, and (iii) symmetric sponge like. These variations were influenced by zeolite weight loading and the flow rate of water used to form the lumen. The separation performances of the glass hollow fiber membrane were studied using the pure water permeability and the rejection test of bovine serum albumin (BSA). The glass hollow fiber membrane prepared from using 48 wt% zeolite loading and bore fluid with 9 mL min(-1) flow rate has the highest BSA rejection of 85% with the water permeability of 0.7 L m(-2) h(-1) bar(-1). The results showed that the separation performance of glass hollow fiber membranes was in the ultrafiltration range, enabled the retention of solutes with molecular sizes larger than 67 kDa such as milk proteins, endotoxin pyrogen, virus, and colloidal silica.
Malaysia is one of the highest starch producers. In this study, sago starch was utilized as a natural coagulant aid to reduce the dosage of aluminum-based coagulant in leachate treatment. The potential of native sago trunk starch (NSTS) and commercial sago starch (CSS) was evaluated as sole coagulant and coagulant aid in the presence of polyaluminum chloride (PACl) in the removal of color, suspended solids (SS), NH3-N, turbidity, chemical oxygen demand, organic UV254, Cd, and Ni. Leachate was sampled from Pulau Burung Landfill Site, one of the semi-aerobic landfills in Malaysia. The optimum dosage for PACl in the presence of NSTS or CSS as coagulant aid was reduced from 3100 to 2000 mg/L. In the presence of 2000 mg/L PACl with 6000 mg/L NSTS and 2000 mg/L PACl with 5000 mg/L CSS, the removal performance for color, SS, and turbidity are 94.7, 99.2, and 98.9%, respectively. Similar results were obtained with the use of 3100 mg/L PACl alone. Therefore, CSS and NSTS can be used as coagulant aid.
The Yoon-Nelson model serves as a widely used tool for describing the breakthrough behavior of organic micropollutants within fixed bed adsorbers. This study aims to augment its modeling efficacy through two proposed refinements found in the literature: a logarithmic transformation and the incorporation of steric hindrance effects. We systematically evaluated the original Yoon-Nelson model alongside the modified versions, using breakthrough data associated with micropollutant adsorption on solid materials. Three distinct cases were scrutinized: (1) caffeine adsorption on activated carbon; (2) tetracycline adsorption on hierarchical porous carbon; and (3) diclofenac adsorption on organoclay. While all three models demonstrated comparable performance with highly symmetric breakthrough data in case 1, their efficacy diverged significantly when confronted with strongly asymmetric breakthrough data in cases 2 and 3. The original Yoon-Nelson model and the logarithmically modified version fell short in accurately representing these intricate breakthrough curves. In contrast, the version incorporating steric hindrance effects showcased substantial accuracy, outperforming other models in capturing the complexities of asymmetric breakthrough data. This advancement markedly enhances the modeling accuracy and versatility of the Yoon-Nelson model, particularly in assessing the dynamic behavior of organic micropollutants within fixed bed adsorbers.
Microplastic pollution is one of the most pressing global environmental problems due to its harmful effects on living organisms and ecosystems. To address this issue, researchers have explored several techniques to successfully eliminate microplastics from water sources. Chemical coagulation, electrocoagulation, magnetic extraction, adsorption, photocatalytic degradation, and biodegradation are some of the recognized techniques used for the removal of microplastics from water. In addition, membrane-based techniques encompass processes propelled by pressure or potential, along with sophisticated membrane technologies like the dynamic membrane and the membrane bioreactor. Recently, researchers have been developing advanced membranes composed of metal-organic frameworks, MXene, zeolites, carbon nanomaterials, metals, and metal oxides to remove microplastics. This paper aims to analyze the effectiveness, advantages, and drawbacks of each method to provide insights into their application for reducing microplastic pollution.
Water reuse/recycle has gained much attention in recent years for environmental sustainability reasons, as well as the rising costs of fresh water and effluent treatment. Process integration techniques for the synthesis of water network have been widely accepted as a promising tool to reduce fresh water and wastewater flowrates via in-plant water reuse/recycle. To date, the focus in this area has been on water network synthesis problems, with little attention dedicated to the rare but realistic cases of so-called threshold problems. In this work, targeting for threshold problems in a water network is addressed using the recently developed numerical tool of water cascade analysis (WCA). Targeting for plant-wide integration is then addressed. By sending water sources across different geographical zones in plant-wide integration, the overall fresh water and wastewater flowrates are reduced simultaneously.
Matched MeSH terms: Water Purification/instrumentation*; Water Purification/methods
Microbial desalination cells (MDCs) have been experimentally proven as a versatile bioelectrochemical system (BES). They have the potential to alleviate environmental pollution, reduce water scarcity and save energy and operational costs. However, MDCs alone are inadequate to realise a complete wastewater and desalination treatment at a high-efficiency performance. The assembly of identical MDC units that hydraulically and electrically connected can improve the performance better than standalone MDCs. In the same manner, the coupling of MDCs with other BES or conventional water reclamation technology has also exhibits a promising performance. However, the scaling-up effort has been slowly progressing, leading to a lack of knowledge for guiding MDC technology into practicality. Many challenges remain unsolved and should be mitigated before MDCs can be fully implemented in real applications. Here, we aim to provide a comprehensive chronological-based review that covers technological limitations and mitigation strategies, which have been developed for standalone MDCs. We extend our discussion on how assembled, coupled and scaled-up MDCs have improved in comparison with standalone and lab-scale MDC systems. This review also outlines the prevailing challenges and potential mitigation strategies for scaling-up based on large-scale specifications and evaluates the prospects of selected MDC systems to be integrated with conventional anaerobic digestion (AD) and reverse osmosis (RO). This review offers several recommendations to promote up-scaling studies guided by the pilot scale BES and existing water reclamation technologies.
Membrane based technologies are highly reliable for water and wastewater treatment, including for removal of total oil and grease from produced water. However, performances of the pressure driven processes are highly restricted by membrane fouling and the application of traditional air bubbling system is limited by their low shear stress due to poor contacts with the membrane surface. This study develops and assesses a novel finned spacer, placed in between vertical panel, for membrane fouling control in submerged plate-and-frame module system for real produced water filtration. Results show that permeability of the panel is enhanced by 87% from 201 to 381 L/(m2 h bar). The spacer system can be operated in switching mode to accommodate two-sided panel aeration. This leads to panel permeability increment by 22% higher than the conventional vertical system. The mechanisms of finned spacer in encouraging the flow trajectory was proven by visual observation and flow simulation. The fins alter the air bubbles flow trajectory toward the membrane surface to effectively scour-off the foulant. Overall results demonstrate the efficacy of the developed spacer in projecting the air bubble trajectory toward the membrane surface and thus significantly enhances membrane panel productivity.
Membrane distillation (MD) is an advantageous separation process compared with pressure-driven technologies and was subsequently introduced to treat aquaculture wastewater. Harnessing a superhydrophobic membrane in an MD process is of extreme importance to prevent membrane wetting. In this work, the electrospun polypropylene (PP) membrane was surface modified by depositing an additional coating of PP via the solvent-exchange method, thereby improving the membrane's superhydrophobicity. Layer-by-layer deposition of PP caused the formation of uniform polymer spherulites on the membrane surface, which levelled up the membrane's surface roughness. A superhydrophobic surface was achieved by applying a single-layered PP coating, with static water contact angle of 152.2° and sliding angle of 12.5°. While all membranes achieved almost perfect salt rejection (up to 99.99%), the MD permeate flux improved by 30%, average of 13.0 kg/m2h, when the single-layered PP-coated membrane was used to treat the high salinity water in both 2 and 60 hr MD processes. Further layers of coating resulted in larger size of PP spherulites with higher sliding angle, followed by lowered flux in MD. The evenness of the surface coating and the size of the aggregate PP spherulites (nano-scaled) are two predominant factors contributing to the superhydrophobicity character of a membrane.
This investigation explores the efficacy of employing ultrasonic cavitation and coupling it with advanced oxidation processes (hydrogen peroxide and Fenton's reagent) for reducing the levels of total ammonia nitrogen in fish pond water containing Tilapia fishes. Ultrasonic cavitation is a phenomenon where the formation, growth and collapse of vaporous bubbles occur in a liquid medium producing highly reactive free radicals. Ultrasonic probe system (20 kHz with 750 W and 1000 W) was used to induce cavitation. Besides, to intensify the process, ultrasonic cavitation was coupled with hydrogen peroxide and Fenton's reagent. Using SERA colour indicator test kits, the levels of ammonium, nitrite and carbonate hardness were measured. The results obtained from this study clearly show that the advanced oxidation processes are more efficient in reducing the ammonium and nitrite levels in fish pond water than using ultrasound alone. The pH and carbonate hardness levels were not affected significantly by ultrasonic cavitation. The optimal treatment time and ultrasound power to treat the water samples were also established. Energy efficiency and cost analysis of this treatment have also been presented, indicating that ultrasonic cavitation coupled with hydrogen peroxide appears to be a promising technique for reducing total ammonia nitrogen levels in the fish pond water.
The vast amount of oily wastewater released to the environment through industrialization has worsened the water quality in recent years, posing adverse impacts on general human health. Oil emulsified in water is one of the most difficult mixtures to be treated, making it imperative for new technology to be explored to address this issue. The use of conventional water treatment such as flotation, coagulation, precipitation, adsorption, and chemical treatment have low separation efficiencies and high energy costs, and are not applicable to the separation of oil/water emulsions. Therefore, there is a demand for more efficient methods and materials for the separations of immiscible oil/water mixtures and emulsions. Superwetting materials that can repel oil, while letting water pass through have been widely explored to fit into this concern. These materials usually make use of simultaneous hydrophilic/oleophobic mechanisms to allow a solid surface to separate oily emulsion with little to no use of energy. Also, by integrating specific wettability concepts with appropriate pore scale, solid surfaces may achieve separation of multifarious oil/water mixtures namely immiscible oil/water blends and consolidated emulsions. In this review, materials used to impart superwetting in solid surfaces by focusing on superhydrophilic/superoleophobic wetting properties of the materials categorized into fluorinated and non-fluorinated surface modification are summarized. In each material, its background, mechanism, fabricating processes, and their effects on solid surface's wetting capability are elaborated in detail. The materials reviewed in this paper are mainly organic and green, suggesting the alternative material to replace the fluorine group that is widely used to achieve oleophobicity in oily wastewater treatment.
Chemical pollution in the transboundary Langat River in Malaysia is common both from point and non-point sources. Therefore, the water treatment plants (WTPS) at the Langat River Basin have experienced frequent shutdown incidents. However, the Langat River is one of the main sources of drinking water to almost one-third of the population in Selangor state. Meanwhile, several studies have reported a high concentration of Arsenic (As) in the Langat River that is toxic if ingested via drinking water. However, this is a pioneer study that predicts the As concentration in the Langat River based on time-series data from 2005-2014 to estimate the health risk associated with As ingestion via drinking water at the Langat River Basin. Several time-series prediction models were tested and Gradient Boosted Tree (GBT) gained the best result. This GBT model also fits better to predict the As concentration until December 2024. The mean concentration of As in the Langat River for both 2014 and 2024, as well as the carcinogenic and non-carcinogenic health risks of As ingestion via drinking water, were within the drinking water quality standards proposed by the World Health Organization and Ministry of Health Malaysia. However, the ingestion of trace amounts of As over a long period might be detrimental to human health because of its non-biodegradable characteristics. Therefore, it is important to manage the drinking water sources to minimise As exposure risks to human health.
This article offers a trend of inventions and implementations of photocatalysis process, desalination technologies and solar disinfection techniques adapted particularly for treatment of industrial and domestic wastewater. Photocatalysis treatment of wastewater using solar energy is a promising renewable solution to reduce stresses on global water crisis. Rendering to the United Nation Environment Programme, 1/3 of world population live in water-stressed countries, while by 2025 about 2/3 of world population will face water scarcity. Major pollutants exhibited from numerous sources are critically discussed with focus on potential environmental impacts & hazards. Treatment of wastewater by photocatalysis technique, solar thermal electrochemical process, solar desalination of brackish water and solar advanced oxidation process have been presented and systematically analysed with challenges. Both heterogenous and homogenous photocatalysis techniques employed for wastewater treatment are critically reviewed. For treating domestic wastewater, solar desalination technologies adopted for purifying brackish water into potable water is presented along with key challenges and remedies. Advanced oxidation process using solar energy for degradation of organic pollutant is an important technique to be reviewed due to their effectiveness in wastewater treatment process. Present article focused on three key issues i.e. major pollutants, wastewater treatment techniques and environmental benefits of using solar power for removal of pollutants. The review also provides close ideas on further research needs and major concerns. Drawbacks associated with conventional wastewater treatment options and direct solar energy-based wastewater treatment with energy storage systems to make it convenient during day and night both listed. Although, energy storage systems increase the overall cost of the wastewater treatment plant it also increases the overall efficiency of the system on environmental cost. Cost-efficient wastewater treatment methods using solar power would significantly ensure effective water source utilization, thereby contributing towards sustainable development goals.
Hazardous industrial wastes negatively impact the environment by creating issues for aquatic as well as human's life. This study investigates the treatment of hazardous industrial wastewater using cost-effective graphite adsorbent along with electrochemical regeneration integrated with renewable solar energy. The synthetic industrial effluent containing crystal violet dye was treated using an adsorbent (Nyex™ 1000) having a surface area of 1.0 m2 g-1 . The efficiency of removing solute was found to be more than 90%. The adsorbent regeneration efficiency was achieved at 99.5% by passing a charge of 100 C g-1 at current density of 10 mA cm-2 for 1 h. Solar energy was integrated with electrochemical reactor for the regeneration of adsorbent to make the system cost-effective and self-sustainable. PRACTITIONER POINTS: Industrial hazardous wastewater treatment with a cost-effective graphite integrated adsorbent. Development of renewable solar energy-integrated with electrochemical system for regeneration. Regeneration efficiency of adsorbent Nyex™ 1000 was achieved around 99.5% with integrated system. Sustainable system was introduced to incorporate with renewable energy for waste water treatment.
Surging growth of aquaculture industry has alarmed the public when the wastewater discharged had an adverse effect on the environment. This current study is a pioneer in the use of membrane distillation (MD) to treat real aquaculture wastewater. In addition to excellent hydrophobicity, the slippery surface of membrane used for MD is another key factor that enhances the performance of MD. The slippery surface of the membrane was tuned by layering high-viscosity and low-viscosity polypropylene (PP) polymers on the electrospun membrane by solvent-exchanged method. While the high-viscosity PP coating (PP/HV) rendered the membrane surface slippery, the low-viscosity PP coating (PP/LV) caused the fish farm wastewater to have stick-slip movement on the membrane surface. In the long-term 70-hour direct contact membrane distillation (DCMD) separation, PP/HV and PP/LV membranes can perfectly eliminate the undesirable components in the fish farm wastewater. The PP/HV membrane has registered a flux of 19.1 kg/m2·h, while the flux of PP/LV membrane was only 7.3 kg/m2·h. The PP/HV membrane also showed excellent anti-scaling properties in relative to the PP/LV membrane. This is because the PP/HV membrane promotes effortless gliding of the feed water along the surface of the membrane, while the surface of the PP/LV membrane has a static water boundary. Therefore, it can be concluded that the application of MD using the membrane coated with high-viscosity PP polymer is a feasible technology for the treatment of aquaculture wastewater.
The current novel work presents the optimization of factors affecting defluoridation by Al doped ZnO nanoparticles using response surface methodology (RSM). Al doped ZnO nanoparticles were synthesized by the sol-gel method and validated by FTIR, XRD, TEM/EDS, TGA, BET, and particle size analysis. Moreover, a central composite design (CCD) was developed for the experimental study to know the interaction between Al doped ZnO adsorbent dosage, initial concentration of fluoride, and contact time on fluoride removal efficiency (response) and optimization of the process. Analysis of variance (ANOVA) was achieved to discover the importance of the individual and the effect of variables on the response. The model predicted that the response significantly correlated with the experimental response (R2 = 0.97). Among the factors, the effect of adsorbent dose and contact time was considered to have more influence on the response than the concentration. The optimized process parameters by RSM presented the adsorbent dosage: 0.005 g, initial concentration of fluoride: 1.5 g/L, and contact time: 5 min, respectively. Kinetic, isotherm, and thermodynamic studies were also investigated. The co-existing ions were also studied. These results demonstrated that Al doped ZnO could be a promising adsorbent for effective defluoridation for water.
Millions of litters of multifarious wastewater are directly disposed into the environment annually to reduce the processing costs leading to eutrophication and destroying the clean water sources. The bioelectrochemical systems (BESs) have recently received significant attention from researchers due to their ability to convert waste into energy and their high efficiency of wastewater treatment. However, most of the performed researches of the BESs have focused on energy generation, which created a literature gap on the utilization of BESs for wastewater treatment. The review highlights this gap from various aspects, including the BESs trends, fundamentals, applications, and mechanisms. A different review approach has followed in the present work using a bibliometric review (BR) which defined the literature gap of BESs publications in the degradation process section and linked the systematic review (SR) with it to prove and review the finding systematically. The degradation mechanisms of the BESs have been illustrated comprehensively in the current work, and various suggestions have been provided for supporting future studies and cooperation.