Land development, especially construction works, increase storm water volumes and pollution loads into rivers and lakes. The temporary drainage system at construction sites, particularly during the construction stage discharges a large amount of pollutants that can damage the aquatic system of the receiving water bodies. The potential of vegetative swale to alleviate this problem was evaluated. The size of the constructed vegetative swale was 7cm deep, 400cm long and 15cm wide at the bottom, and 17cm wide at the top. The experiment was conducted batch wise by filling the storage tank with the run-off water from the construction site. The water was allowed to flow through a pipe into the retention basin to maintain uniform flow before it entered the swale. The study showed that the run-off infiltrated through the soil at a rate of 489.6 mm/hr. Samples of surface run-off and infiltration water were collected at the end and the bottom of the swale. The results indicate that chemical oxygen demand (COD), total suspended solid (TSS), turbidity, iron and zinc were reduced by 85.4%, 80.8%, 36.4%, 52.8% and 96.0%, respectively, by surface flow and 91.1%, 98.8%, 58.2% 55.5% and 98.1%, respectively, by infiltration. Removal of nitrate and phosphorus by the planted vegetation was 69.4% and 21.1%, respectively, by infiltration. However, nutrient removal by surface flow was negligible. In conclusion, the vegetative swale was able to improve the water quality of the storm water run-off from the construction site from Class V to Class III, according to the Interim National Water Quality Standards for Malaysia.
Ficus deltoidea leaves were widely used as a tea beverages in Malaysia with no information of its mineral content. Hence the mineral content of two species of Ficus deltoidea leaves were investigated. The dried leaves of F. deltoidea var. angustifolia and F. deltoidea var. deltoidea were acid digested and mineral elements of Na, Mg, K, Ca, Mn, Cr, Fe and Zn were determined using ICP–MS. Magnesium, potassium, sodium, manganese, iron and zinc were found to be present in the leaves of F. deltoidea var. angustifolia and F. deltoidea var. deltoidea. Concentration of magnesium (1934 mg/L), manganese (58.37 mg/L), iron (6.89 mg/L) and zinc (1.77 mg/L) in F. deltoidea var. deltoidea species were significantly (P < 0.05) higher than in F. deltoidea var. angustifolia species with concentration of 317 mg/L, 29.62 mg/L, 4.55 mg/L and 1.26 mg/L for magnesium, manganese, iron and zinc respectively. Meanwhile, concentration of sodium in F. deltoidea var. deltoidea species (3.13 mg/L) was found to be significantly (P < 0.05) lower than the concentration in F. deltoidea var. angustifolia species (9.11 mg/L). The finding showed that the leaves of F. deltoidea var. deltoidea has higher nutritional value than the leaves of F. deltoidea var. angustifolia. Leaves of Ficus deltoidea especially the F. deltoidea var. deltoidea species contain high amount of magnesium, manganese and potassium. Therefore, tea made of this leaves can be served as a good source of minerals for human consumption.
The status ofhve l1eavy metals: cadmium, lead copper, zinc and mercury were determined in seafood and its products imported_ti·om Thailand via Bukit Kayu Hiram, Kedah, Flame Atomic Absorption Spectrophotometer was used to determine the level of these heary metals except for mercury, where the cold vapor technique was used, Randomized sampling was done according to a predetermined sampling plan based on the previous years consignments. Data collected were compared with the maximum permitted level of -metal contaminants in fish and fish products- ofthe Fourteenth Schedule (Regulation 38) of Food Act I983 and Food Regulations I 985 to ascertain compliance. lt was noted form this study, that the level of metals detected in seafood and its products had a very wide range, The levels detected for cadmium was at a range of 0. 00] - 3.9/2, 0.07 — 0.29, 0,04 - 4,4 mg/kg in fish, shellfish and cuttlefish respectivelv. In general, cadmium level in some samples was notably higher particularly in shellfish. All samples had lead level less than the permitted value except for fish where the highest value detected was 3.28 mg/kg. The level of copper and zinc was higher than the permitted value in octopus, prawn and crab, Mercury level in all samples analvzed was found to be below the detection level. As for fish samples, zinc level was found to be higher whereas copper was within the limit. However, it was also noted that the level of all the heavy metals in jiozen jish was within the permitted limit.
Trace metals are required in many cellular processes in bacteria but also induce toxic effects to cells when present in excess. As such, various forms of adaptive responses towards extracellular trace metal ions are essential for the survival and fitness of bacteria in their environment. A soil Pseudomonas putida, strain S13.1.2 has been isolated from French vineyard soil samples, and shown to confer resistance to copper ions. Further investigation revealed a high capacity to tolerate elevated concentrations of various heavy metals including nickel, cobalt, cadmium, zinc and arsenic. The complete genome analysis was conducted using single-molecule real-time (SMRT) sequencing and the genome consisted in a single chromosome at the size of 6.6 Mb. Presence of operons and gene clusters such as cop, cus, czc, nik, and asc systems were detected and accounted for the observed resistance phenotypes. The unique features in terms of specificity and arrangements of some genetic determinants were also highlighted in the study. Our findings has provided insights into the adaptation of this strain to accumulation and persistence of copper and other heavy metals in vineyard soil environment.
The natural environment embraces agriculture and all its components-crops, animals, land, water,
forestry and fisheries. It is the most important user of environmental resources, made more complex
by the interactions of the various systems, biophysical elements and their implications. Increased food
production, especially of animal protein supplies are unable to meet current and projected future needs
for humans, including about 15 %of the world population being malnourished. Agriculture is currently
waning, and a coordinated and concerted technologically-driven transformation is necessary. Poorly
managed agriculture for example, can lead to serious environmental degradation and exacerbate
poverty. Land and water are considered to be the most limiting factors in the future. Non- irrigated
rainfed areas can be divided into high potential and low potential areas; the former offers considerable
promise to expand food production. This paper argues for increased Research and Development (R&D)
focus that can maximise improved natural resource management(NRM), and whether agricultural
development can maximise productivity yields .Other opportunities include expanding crop–animal
production systems in less favoured areas (LFAs), intensifying land use for silvopastoral systems in
rainfed areas , and enhance carbon sequestration. Ruminants can be used as an entry point for the
development of LFAs, and the presence of about 41.5% of the goat population found in the semi-arid/
arid AEZs X provides good opportunities for expanding food security and human well-being. Communitybased
interdisciplinary and systems approaches are essential to provide the solutions. The legacy of
continuing malnutrition and food insecurity must be overcome by effective development policy, multidonor
resource allocation, governance and political will that target food insecurity and poverty. The R&D
agendas and resource allocations are compelling, but dedicated vision can lead the way for sciencedriven
sustainable environment, efficiency in NRM, and self-reliance to the extent possible , in harmony
with nature and the environment.
Although carbon dioxide (CO2) is well known as one of the major green-house gases, it is also an economical C1 resource. Thus, CO2has been regarded as an appealing starting material for the synthesis of polymers, like polycarbonates by the reaction with epoxides. Herein the reaction between natural epoxidized soybean oil (ESO), propylene oxide (PO) and CO2under high pressure (4.0MPa) with the presence of Co-Zn double metal cyanide (Co-Zn DMC) catalyst was studied. Temperature and reaction time were varied accordingly and the products obtained were characterized by FTIR, GPC and1H NMR. The results obtained indicate the formation of polycarbonates in the samples collected with yields vary from 60 to 85%. The number average molecular weight (Mn) of the resultant polymer prepared at reaction temperature of 80°C and reaction time of 6h can reach up to 6498g/mol.
High concentration of fluoride in wastewater discharge from various industries is threatening the environment due to its hazardous effects and properties. This research work aims to develop an efficient adsorbent for fluoride removal in wastewater. Graphite oxide (GO) was impregnated
with ZnO nanoparticles as an adsorbent, and the effect of synthesis parameters of GO-ZnO adsorbent for fluoride removal were studied (sonication temperature, synthesis time, and ratio of GO to ZnO). The surface functional groups of these synthesized adsorbents were analyzed by
using FTIR. The synthesis parameters that contribute to the highest adsorption capacity and percentage removal are 5:1 ratio of GO-ZnO, 45 ºC of sonication temperature and 60 minutes of synthesis time, respectively. The highest value of adsorption capacity obtained from the fluoride
removal is 55.5 mg/g. The functional groups contained in the GO-ZnO adsorbent are hydroxyl group (O-H), C=O group, aromatics group, carboxyl group (C-O), epoxy group and alkoxy group. These functional groups showed significant impact towards fluoride adsorption due to the bonding of fluoride ion to the functional groups.
Development and urbanization processes around Terengganu River estuary are expected to release a significant amount of heavy metals into the existing surface sediment. However, information on how and why these metals are attached into specific fraction of sediments is still lacking. Therefore, this study aimed to explain the heavy metal concentration distribution in each available fraction in Terengganu River estuary. In this study, nine surface sediments originated from various human activities area in Terengganu River estuary were collected during four different sampling sessions in 2017. Heavy metal content from the collected sediments were extracted using 3-steps BCR sequential extraction method followed by detection using Inductively Coupled Plasma Mass-Spectrometer (ICP-MS) and we discovered that the total concentration of arsenic (As), cobalt (Co), copper (Cu), and zinc (Zn) ranged from 2.18 to 17.48 mg/kg dry wt., 2.53 to 20.53 mg/kg dry wt., 1.01 to 13.13 mg/kg dry wt., and 6.10 to 65.71 mg/kg dry wt., respectively. Dominance of metals in each fraction can be arranged as follows: As: residual > reducible > exchangeable > oxidizable; Co: residual > exchangeable > reducible > oxidizable; Cu: residual > oxidizable > reducible > exchangeable; Zn: residual > exchangeable > reducible > oxidizable. Availability of metals in the sediment at Terengganu River estuary is limited since that majority of metals resides in non-mobilisable fraction of the sediment. In essence, the sequential extraction provides information regarding the metals’ fractionation, availability and mobility, which could be used in assessing the environmental contamination in the area.
Along with the growing utilization of zinc (Zn) and Zn-containing nanoparticles in various industries, Zn ecotoxicological evaluation on human food supply is necessary even though Zn is generally considered safe and rarely concentrated ecotoxicologically. This study aimed to investigate the bioaccumulation of Zn in 18 species of vegetables (seven leafy, nine fruity vegetables and one species each of tuber and legume) collected from two farming sites in the west coast of Peninsular Malaysia. A human health risk assessment (HHRA) was also conducted. In addition to HHRA based on the general population, HHRA based on each major ethnic group of the Malaysian society was also determined considering that the food consumption pattern would definitely be varied across ethnicities and age groups (children and adults). The study results showed that Zn concentrations were significantly higher (p < 0.05) in leafy vegetables than in other types of vegetables. However, the target hazard quotient (THQ) values were all found to be < 1.0. Therefore, based on the Malaysian ethnicities and age groups with their respective vegetable consumption patterns, the results indicated insignificant noncarcinogenic human health risk of Zn via oral consumption of vegetables by the Malaysian population. As a metric of measurement of HHRA, a comparison of THQ values could yield previously unreported insights into HHRA differences among the compared populations. A comparison of THQ values among the consumer groups indicated higher HHR for Chinese Malaysians and children due to their higher vegetable consumption and lower body weight, respectively. A comparison the Zn intakes of all the consumer groups with the recommended nutrient intakes indicated that the oral consumption of the vegetable species collected in this study would not result in Zn-related hazards and would not be able to fulfil the Zn dietary need of the individual consumer.
For highly sensitive pH sensing, an electrolyte insulator semiconductor (EIS) device, based on ZnO nanorod-sensing membrane layers doped with magnesium, was proposed. ZnO nanorod samples prepared via a hydrothermal process with different Mg molar ratios (0-5%) were characterized to explore the impact of magnesium content on the structural and optical characteristics and sensing performance by X-ray diffraction analysis (XRD), atomic force microscopy (AFM), and photoluminescence (PL). The results indicated that the ZnO nanorods doped with 3% Mg had a high hydrogen ion sensitivity (83.77 mV/pH), linearity (96.06%), hysteresis (3 mV), and drift (0.218 mV/h) due to the improved crystalline quality and the surface hydroxyl group role of ZnO. In addition, the detection characteristics varied with the doping concentration and were suitable for developing biomedical detection applications with different detection elements.
Iron oxide nanoparticles are suitable for biomedical applications owing to their ability to anchor to various active agents and drugs, unique magnetic properties, nontoxicity, and biocompatibility. In this work, the physico-chemical and magnetic properties, as well as the cytotoxicity, of Fe3O4 nanoparticles coated with a polymeric carrier and loaded with a 5-fluorouracil (5-FU) anti-cancer drug are discussed. The synthesized Fe3O4 nanoparticles were coated with polyvinyl alcohol and Zn/Al-layered double hydroxide as the drug host. The XRD, DTA/TG, and FTIR analyzes confirmed the presence of the coating layer on the surface of nanoparticles. The results showed a decrease in saturation magnetization of bare Fe3O4 nanoparticles after coating with the PVA/5FU/Zn/Al-LDH layer. In addition, the presence of the coating prevented the agglomeration of nanoparticles. Furthermore, the pseudo-second-order equation governed the kinetics of drug release. Finally, the coated nanoparticles showed stronger activity against liver cancer cells (HepG2) compared to that of the naked 5-FU drug, and displayed no cytotoxicity towards 3T3 fibroblast cell lines. The results of the present study demonstrate the potential of a nano delivery system for cancer treatment.
The hepatitis C virus (HCV) consists of eight genotypes and 90 subtypes, with genotype (GT) 3 being the second most common globally and is linked to higher incidences of steatosis and rapid development of fibrosis and cirrhosis. The NS3/4A serine protease, a heterodimer complex of two HCV non-structural proteins, is an effective target for pharmaceutical intervention due to its essential roles in processing HCV polyproteins and inhibiting innate immunity. This study combines structure-based virtual screening (SBVS) of predefined compound libraries, pharmacokinetic prediction (ADME/T) and in vitro evaluation to identify potential low molecular weight (<500 Dalton) inhibitors of the NS3/4A serine protease (GT3). In silico screening of ZINC and PubChem libraries yielded five selected compounds as potential candidates. Dose-dependent inhibition of the NS3/4A serine protease and HCV replication in HuH-7.5 cells revealed that compound A (PubChem ID No. 16672637) exhibited inhibition towards HCV GT3 with an IC50 of 106.7µM and EC50 of 25.8µM, respectively. Thus, compound A may be developed as a potent, low molecular weight drug against the HCV NS3/4A serine protease of GT3.
A widely distributed urban bird, the house crow (Corvus splendens), was used to assess bioavailable heavy metals in urban and rural environments across Pakistan. Bioaccumulation of arsenic (As), zinc (Zn), lead (Pb), cadmium (Cd), nickel (Ni), iron (Fe), manganese (Mn), chromium (Cr), and copper (Cu) was investigated in wing feathers of 96 crows collected from eight locations and categorized into four groups pertaining to their geographical and environmental similarities. Results revealed that the concentrations of Pb, Ni, Mn, Cu, and Cr were positively correlated and varied significantly among the four groups. Zn, Fe, Cr, and Cu regarded as industrial outputs, were observed in birds both in industrialized cities and in adjoining rural agricultural areas irrigated through the Indus Basin Irrigation System. Birds in both urban regions accrued Pb more than the metal toxicity thresholds for birds. The house crow was ranked in the middle on the metal accumulation levels in feathers between highly accumulating raptor and piscivore and less contaminated insectivore and granivore species in the studied areas,. This study suggests that the house crow is an efficient bioindicator and supports the feasibility of using feathers to discriminate the local pollution differences among terrestrial environments having different levels and kinds of anthropogenic activities.
Mangrove located near urban area is exposed to various industrial discharge including heavy metals. Mangrove soil is capable of accumulating and storing these heavy metals. Heavy metals are toxic and non-biodegradable, so their accumulations affect water quality, while bioaccumulation and bio-assimilation of heavy metals in mangrove organisms negatively impact the food chain. Bacteria-derived biosurfactants are compounds capable of removing heavy metals from soil and sediment. Furthermore, environmentally friendly properties, such as biodegradability and low toxicity, exhibited by biosurfactants make them a suitable replacement for chemical surfactants for remediation efforts. This study was conducted to investigate the lead- (Pb) and zinc- (Zn) removing capability of rhamnolipid (RL), a type of biosurfactant produced by marine bacterium, Pseudomonas aeruginosa UMTKB-5. Rhamnolipid solutions of three different concentrations (25 mg/L, 50 mg/L and 75 mg/L) were added to mangrove soil and incubated for 7 days. The removal of Pb from soils was up to 18.3% using 25 mg/L RL solution, while 50 mg/L RL solution removed 48.3%, and 75 mg/L RL solution removed 75.9% Pb over time. Meanwhile, zinc removal of 25 mg/L RL solution was up to 24.9%, while 50 mg/L removed 16.5%, and 75 mg/L RL removed 30.5% of Zn. The results showed that RL from P. aeruginosa UMTKB-5 could be a potential biomaterial to be used to remediate heavy metals in sediment.
Semiconductor oxides such as titanium dioxide (TiO2) and zinc oxide (ZnO) are used as the photocatalyst for removing contaminants. In addition, TiO2 and ZnO nanoparticles in the suspension form makes it difficult to be recovered and recycled. This study was conducted to investigate the efficiency of immobilizing TiO2 and ZnO nanoparticles in epoxy beads. The immobilization process using different ratios of photocatalysts TiO2/ZnO (1:0, 3:1, 1:1, 1:3 and 0:1) fixed on epoxy material. These epoxy beads were used for dye removal in photocatalysis using methylene blue (MB) solution at a concentration of 10mg/L. Besides, epoxy beads also characterized using scanning electron microscope (SEM), attenuated total reflection Fourier-transform infrared (ATR-FTIR) spectroscopy and thermogravimetric analysis (TGA). The results showed that the highly recommended epoxy bead is 3:1 ratio of TiO2/ZnO because it has good performance in dye degradation that proved from reducing concentration of MB to 2.4mg/L (76%). However, TiO2/ZnO characterization of 3:1 by SEM show on the surface the particle are found to be spherical in shape which is relatively high efficiency for the degradation, ATR-FTIR pattern in broad band 4000 cm-1 - 400cm-1 which correspond to hydroxyl stretching to be adsorbed at peak (474.49 cm-1 - 3722.61cm-1) respectively to the optimum for the degradation and TGA rate of change are 5mg to 2.5mg that residue (49.78%) due to decomposition or oxidation from mass loss. These findings are very effective and economical technique to be cost saving and highly efficient photocatalyst.
Chitosan (CS)-dextran (DN) biopolymer electrolytes doped with ammonium iodide (NH4I) and plasticized with glycerol (GL), then dispersed with Zn(II)-metal complex were fabricated for energy device application. The CS:DN:NH4I:Zn(II)-complex was plasticized with various amounts of GL and the impact of used metal complex and GL on the properties of the formed electrolyte were investigated.The electrochemical impedance spectroscopy (EIS) measurements have shown that the highest conductivity for the plasticized system was 3.44 × 10-4 S/cm. From the x-ray diffraction (XRD) measurements, the plasticized electrolyte with minimum degree of crystallinity has shown the maximum conductivity. The effect of (GL) plasticizer on the film morphology was studied using FESEM. It has been confirmed via transference number analysis (TNM) that the transport mechanism in the prepared electrolyte is predominantly ionic in nature with a high transference number of ion (ti)of 0.983. From a linear sweep voltammetry (LSV) study, the electrolyte was found to be electrochemically constant as the voltage sweeps linearly up to 1.25 V. The cyclic voltammetry (CV) curve covered most of the area of the current-potential plot with no redox peaks and the sweep rate was found to be affecting the capacitance. The electric double-layer capacitor (EDLC) has shown a great performance of specific capacitance (108.3 F/g), ESR(47.8 ohm), energy density (12.2 W/kg) and power density (1743.4 W/kg) for complete 100 cycles at a current density of 0.5 mA cm-2.
The intercalation of a drug active, perindopril, into Mg/Al-layered double hydroxide for the formation of a new nanocomposite, PMAE, was accomplished using a simple ion exchange technique. A relatively high loading percentage of perindopril of about 36.5% (w/w) indicates that intercalation of the active took place in the Mg/Al inorganic interlayer. Intercalation was further supported by Fourier transform infrared spectroscopy, and thermal analysis shows markedly enhanced thermal stability of the active. The release of perindopril from the nanocomposite occurred in a controlled manner governed by pseudo-second order kinetics. MTT assay showed no cytotoxicity effects from either Mg/Al-layered double hydroxide or its nanocomposite, PMAE. Mg/Al-layered double hydroxide showed angiotensin-converting enzyme inhibitory activity, with 5.6% inhibition after 90 minutes of incubation. On incubation of angiotensin-converting enzyme with 0.5 μg/mL of the PMAE nanocomposite, inhibition of the enzyme increased from 56.6% to 70.6% at 30 and 90 minutes, respectively. These results are comparable with data reported in the literature for Zn/Al-perindopril.
Sixteen trace elements found in 309 street heroin samples, piped water and contaminated water were determined using inductively coupled plasma-mass spectrometry. All the street heroin samples were found to contain high levels of sodium, a reflection of the use of sodium bicarbonate during heroin synthesis. Additionally, this element was also found to be one of the potential contaminants acquired from the piped water. Calcium could be derived from lime while iron, aluminum and zinc could have come from the metallic container used in the processing/cutting stage. The levels of these elements remained low in the heroin and it could be due to the dilution effects from the addition of adulterants. Statistical validation was performed with six links of related heroin samples using principal component analysis to find the best pretreatment for sample classification. It was obtained that normalization followed by fourth root showed promising results with 8% errors in the sample clustering. The technique was then applied to the case samples. Finally, the result suggested that the case samples could have originated from at least two major groups respectively showing unique elemental profiles at the street level.
A flow injection (FI) method with on-line preconcentration using a mini-column loaded with 8-hydroxyquinoline immobilized on controlled pore glass (CPG-8HQ) is described for the determination of trace metals by ion chromatography (IC) with pyridine-2-6-dicarboxylic acid (PDCA) as the eluent. Copper, cadmium, lead, zinc, nickel and iron were determined at ppb level after post-column derivatization with 4-(2-pyridylazo)-resorcinol (PAR). The detection limits (3sigma) for the FI/IC system were 8.27, 0.89, 0.09, 0.06, 0.09 and 0.07 g l(-1) for Pb(2+), Cd(2+), Cu(2+) Ni(2+), Zn(2+) and Fe(3+), respectively, using 5 ml sample volume. The method was applied to the analysis of Malaysian natural waters.
Cost-effective interventions are needed to address undernutrition, particularly micronutrient deficiencies, which are common in children under the age of five in low- and middle-income countries. A community-based, non-randomized clinical trial was undertaken in the Kurram district of Khyber Pakhtunkhwa from January 2018 to June 2019, to evaluate the effect of locally produced micronutrient powder (local name: Vita-Mixe) on plasma micronutrient status, hemoglobin level, and anthropometric outcomes. Children aged 24-48 months old were recruited and allocated to the intervention and control arm of the study. The enrolled children in the intervention arm received one micronutrient powder (MNP) sachet for consumption on alternate days for 12 months. To assess the impact of the intervention on plasma levels of zinc, vitamin D, vitamin A, and hemoglobin level, blood samples were taken at baseline and after one year following the intervention. The analysis was conducted using Enzyme-Linked Immunosorbent Assay (ELISA), atomic absorption spectrometry, and an automated hematology analyzer. For the impact on growth parameters, the anthropometric assessment was performed using WHO standard guidelines. A 24 h dietary recall interview was used to assess the nutrient intake adequacy. Results showed that in the intervention arm, children had on average a 7.52 ng/mL (95% CI 5.11-9.92, p-value < 0.001) increase in the plasma level of vitamin A, 4.80 ng/mL (95% CI 1.63-7.95, p-value < 0.002) increase in vitamin D levels and 33.85 µg/dL (95% CI 24.40-43.30, p-value < 0.001) increase in the plasma zinc level, as well as a 2.0g/dL (95% CI 1.64-2.40, p-value < 0.001) increase in hemoglobin level. Statistically significant improvement was observed in the weight-for-height z-score (WHZ) (from -1.0 ± 0.88 to -0.40 ± 1.01, p < 0.001) and weight-for-age z-score (WAZ) (from -1.40 ± 0.50 to -1.05 ± 0.49, p < 0.001) in the intervention group compared to the control group. No statistically significant change was observed in the height-for-age z-score (HAZ) in the intervention group (p = 0.93). In conclusion, micronutrient powder supplementation is a cost-effective intervention to improve the micronutrient status, hemoglobin level, and growth parameters in under-five children, which can be scaled up in the existing health system to address the alarming rates of undernutrition in Pakistan and other developing countries.