The removal of impurities from water or wastewater by the membrane filtration process has become more reliable due to good hydraulic performance and high permeate quality. The filterability of the membrane can be improved by having a material with a specific pore structure and good hydrophilic properties. This work aims at preparing a polyvinylidene fluoride (PVDF) membrane incorporated with phospholipid in the form of a 2-methacryloyloxyethyl phosphorylcholine, polymeric additive in the form of polyvinylpyrrolidone, and its combination with inorganic nanosilica from a renewable source derived from bagasse. The resulting membrane morphologies were analyzed by using scanning electron microscopy. Furthermore, atomic force microscopy was performed to analyze the membrane surface roughness. The chemical compositions of the resulting membranes were identified using Fourier transform infrared. A lab-scale cross-flow filtration system module was used to evaluate the membrane's hydraulic and separation performance by the filtration of humic acid (HA) solution as the model contaminant. Results showed that the additives improved the membrane surface hydrophilicity. All modified membranes also showed up to five times higher water permeability than the pristine PVDF, thanks to the improved structure. Additionally, all membrane samples showed HA rejections of 75-90%.
Fat, oil and grease in wastewater generated from household kitchens, restaurants and food processing plants affect sewer systems, water resources and environment adversely. Hence, membrane distillation of saline and oily water was studied using a nearly superhydrophobic membrane developed in this work. Polyvinylidene fluoride (PVDF) membrane incorporated SiO2 nanoparticles was synthesized via phase inversion with dual baths and modified using hexadecyltrimethoxy silane. The volume ratio of silane to ethanol was varied between 1:200 to 1:25. The membrane characteristics were examined using a goniometer, a porometer, scanning electron microscopy (SEM) and Fourier transform infrared spectroscopy (FTIR). The PVDF-SiO2 membrane modified using the volume ratio of 1:50 achieved the highest water contact angle of 141.6° and LEP of 2.642 bar. This membrane was further tested in membrane distillation to observe the permeate flux of distilled water, saline solution (1 M NaCl) as well as saline and oily solution (1 M NaCl; 1,000 ppm of palm oil). The modified PVDF/SiO2 showed high permeate flux which is nearly four times of the permeate flux of neat PVDF membrane, but still susceptible of salt and oil fouling as shown in SEM images.
Crystallization of amorphous pharmaceutical solids are widely reported to be affected by the addition of polymer, while the underlying mechanism require deep study. Herein, crystal growth behaviors of glassy griseofulvin (GSF) doped with various 1% w/w polymer were systematically studied. From the molecular structure, GSF cannot form the hydrogen bonding interactions with the selected polymer poly(vinyl acetate), polyvinyl pyrrolidone (PVP), 60:40 vinyl pyrrolidone-vinyl acetate copolymer (PVP/VA 64), and poly(ethylene oxide) (PEO). 1% w/w polymer exhibited weak or no detectable effects on the glass transition temperature (Tg) of GSF. However, crystal growth rates of GSF was altered from 4.27-fold increase to 2.57-fold decrease at 8 ℃ below Tg of GSF. Interestingly, the ability to accelerate and inhibit the growth rates of GSF crystals correlated well with Tg of polymer, indicating the controlling role of segmental mobility of polymer. Moreover, ring-banded growth of GSF was observed in the polymer-doped systems. Normal compact bulk and ring-banded crystals of GSF were both characterized as the thermodynamically stable form I. More importantly, formation of ring-banded crystals of GSF can significantly weaken the inhibitory effects of polymer on the crystallization of glassy GSF.
Objective: To evaluate the effect of type of viscosity and groove on surface detail reproduction of elastomeric impression materials. Methods: Two polyvinylsiloxane and polyether elastomeric impression materials were investigated. An aluminium cylindrical reference block with V- and U-shaped grooves of 1 mm and 2 mm in depth was machined using CAD-CAM system. Impressions of the block were taken to produce 35 master dies. Each die was immersed in distilled water for 5 minutes prior to impression making. Surface topography of the dies and impressions were captured using Alicona Imaging System. Mean difference in depth between the mas-ter dies and corresponding impressions’ grooves were analyzed. Results: Type of viscosities and groove showed significant main effects on surface detail (p < .01), but no significant interaction was observed between the two (p > .01). Express™ putty/light exhibited the lowest mean difference in depth for all grooves. The highest mean difference for U1 (38.3μm ± 21.55), U2 (52.96μm ± 30.39),V1 (45.02μm ± 34.82) and V2 (58.44μm ± 44.19) was obtained from Impregum medium, Aquasil medium, Impregum™ heavy/light and Impregum™ heavy/light groups respectively. Conclusion: Express putty/light-bodied material produced the best surface detail, and U-shaped groove showed superior detail reproduction.
Natural fiber reinforced composites have had a great impact on the development of eco-friendly industrial products for several engineering applications. Sugar palm fiber (SPF) is one of the newly found natural fibers with limited experimental investigation. In the present work, sugar palm fiber was employed as the natural fiber reinforcement. The composites were hot compressed with polyvinyl butyral (PVB) to form the structure of laminated composites and then were subjected to tensile testing and moisture absorption. The maximum modulus and tensile strength of 0.84 MPa and 1.59 MPa were registered for samples PVB 80-S and PVB 70-S, respectively. Subsequently, the latter exhibited the highest tensile strain at a maximum load of 356.91%. The moisture absorption test revealed that the samples exhibited better water resistance as the proportion of PVB increased relative to the proportion of SPF due to the remarkable hydrophobic property of PVB in comparison with that of SPF.
Two different supercapacitor configurations were fabricated using coconut shell-based activated
carbon. Results for cyclic voltammetry (CV), electrochemical impedance spectroscopy (EIS), and charge-discharge measurements are presented and discussed for both configurations. The results show that coconut shell-based activated carbon is viable economical alternative electrode material to expensive activated carbon (AC) and carbon nano tubes (CNT). Meanwhile, the calculations from the charge-discharge characteristics show that the disk-shape supercapacitor, with 10% polyvinylidene fluoride binder (PVdF), has the highest specific capacitance (70F/g). Thus, the testing shows that the flat-laminated super-capacitor with 10% binder (PVdF) has the lowest (10.1ohms). Sources of high equivalent series resistance (ESR) are proposed and methods of reducing it are also discussed in this paper.
Affordable and greener materials were extensively studied in electrode fabrication for Liion
based batteries but less interest was shown to proton battery. Hence, in this work,
a methodology on preparing a natural based binder for proton battery was reported. 2-
Hydroxyethyl Cellulose (2HEC) was chosen to replace PVDF commercial binder in electrode
for ZnSO4|MnO2 proton battery configuration. SEM image shows good surface formation
for both anode and cathode with good porous structure. OCV result shows that the cell
improved the stable voltage of reference cell of 0.7 V to 0.9 V after 24 hours. The first
discharge of the cell took 6 hours and 49 minutes at 0.005mA and shows good potential for
rechargebility test.
The direct determination of toxic metal ions, in environmental samples, is difficult because of the latter's presence in trace concentration in association with complex matrices, thereby leading to insufficient sensitivity and selectivity of the methods used. The simultaneous removal of the matrix and preconcentration of the metal ions, through solid phase extraction, serves as the promising solution. The mechanism involved in solid phase extraction (SPE) depends on the nature of the sorbent and analyte. Thus, SPE is carried out by means of adsorption, ion exchange, chelation, ion pair formation, and so forth. As polymeric supports, the commercially available Amberlite resins have been found very promising for designing chelating matrices due to its good physical and chemical properties such as porosity, high surface area, durability and purity. This review presents an overview of the various works done on the modification of Amberlite XAD resins with the objective of making it an efficient sorbent. The methods of modifications which are generally based on simple impregnation, sorption as chelates and chemical bonding have been discussed. The reported results, including the preconcentration limit, the detection limit, sorption capacity, preconcentration factors etc., have been reproduced.
Poly (p-phenylene vinylene) (PPV) was synthesized from p-xylylene bis(tetrahydrothiophenium chloride) using the Wessling route and characterized by Fourier Transform Infra-Red (FTIR) and UV-visible (UV-VIS) spectroscopic techniques. The significance of thermal treatment along with evolution of precursor polymer to polymer PPV was also studied through these spectroscopic techniques. Thermally Stimulated Current (TSC) measurements indicated the presence of crystallization, sulphonium group which occurred through the evolution from precursor polymer to polymer PPV during thermal treatment.
Cell adhesion is always the first step in biofilm development. With the emergence of attached cultivation systems, this study aims to promote a cost-effective approach for sustainable cultivation of microalgae, Navicula incerta, by pre-coating the main substrates, commercial polyvinylidene fluoride (PVDF) membranes with its own washed algal cells and self-produced soluble extracellular polymeric substances (EPS) for strengthened biofilm development. The effects of pH value (6 to 9), cell suspension volume (10 to 30 mL), and EPS volume (10 to 50 mL) were statistically optimized by means of response surface methodology toolkit. Model outputs revealed good agreement with cell adhesion data variation less than 1% at optimized pre-coating conditions (7.20 pH, 30 mL cell suspension volume, and 50 mL EPS volume). Throughout long-term biofilm cultivation, results demonstrated that EPS pre-coating substantially improved the attached microalgae density by as high as 271% than pristine PVDF due to rougher surface and the presence of sticky exopolymer particles. Nutrients absorbed via the available EPS coating from the bulk medium made the immobilized cells to release less polysaccharides on an average of 30% less than uncoated PVDF. This work suggests that adhesive polymer binders derived from organic sources can be effectively integrated into the development of high-performance novel materials as biocoating for immobilized microalgae cultivation.
Water contamination due to soluble synthetic dyes has serious concerns. Membrane-based wastewater treatments are emerging as a preferred choice for removing dyes from water. Poly(vinylidene fluoride) (PVDF)-based nanomembranes have gained much popularity due to their favorable features. This review explores the application of PVDF-based nanomembranes in synthetic dye removal through various treatments. Different fabrication methods to obtain high performance PVDF-based nanomembranes were discussed under surface coating and blending methods. Studies related to use of PVDF-based nanomembranes in adsorption, filtration, catalysis (oxidant activation, ozonation, Fenton process and photocatalysis) and membrane distillation have been elaborately discussed. Nanomaterials including metal compounds, metals, (synthetic/bio)polymers, metal organic frameworks, carbon materials and their composites were incorporated in PVDF membrane to enhance its performance. The advantages and limitations of incorporating nanomaterials in PVDF-based membranes have been highlighted. The influence of nanomaterials on the surface features, mechanical strength, hydrophilicity, crystallinity and catalytic ability of PVDF membrane was discussed. The conclusion of this literature review was given along with future research.