MyMedR

Displaying publications 41 - 60 of 85 in total

Abstract:

Sort:

Fulltext Single cultures of acinetobacter sp. and cellulosimicrobium sp. grown in pineapple waste: adaption study and potential in reducing cod from real textile wastewater

Nor Habibah Mohd Rosli, Wan Azlina Ahmad

Science Letters, 2018;12(1):30-43.
MyJurnal

Wastewater from industrial plants such as textile, electroplating and petroleum refineries contains various substances that tend to increase the chemical oxygen demand (COD) of the wastewater. Therefore, it is desired to develop a process suitable for treating the wastewater to meet the regulatory limits. This work was conducted to investigate the potential of adapted single culture of A. baumannii, A.calcoaceticus and C.cellulans in reducing COD in real textile wastewater. The study was carried out by adapting each single culture (10% inoculums) to increasing concentration (1%, 2.5 %, 5%, 7.5 % and 10%) of textile wastewater. Then it was introduced to the textile effluent without pH adjustment for five days and the COD values were measured. The textile wastewater was supplemented with pineapple waste for bacterial growth and metabolism. Results obtained showed that pineapple waste was a good nutrient supply for the growth of the bacteria and the best concentration of textile wastewater for adaptation was at 2.5%. The results also showed that A.calcoaceticus shows highest COD reduction with 67% removal whereas A. baumannii and C.cellulans with 60% and 58% removal respectively. The outcome supported that the single culture used in this study showed considerably high reduction of COD from real textile wastewater.

Matched MeSH terms: Textiles
Fulltext The effect of different jubah dress’ materials on image quality using computed radiography (CR) on Knee X-Ray: a bovine study

Umi Nadrah Amran, Nur Nadiah Mohd Rais

International Journal of Allied Health Sciences, 2018;2(2):292-303.
MyJurnal

In medical imaging practice, the act of removing any clothes from the region of interest is justified as to prevent the presence of artefacts on radiographs. However, by doing so, the ‘aurah’ of the patients, especially for the Muslims, are not observed and can be considered as violating their privacy if they are not well-informed beforehand. Previous studies have proved that radiographs with the presence of some fabric materials on the region of interest are radiographically acceptable. Therefore, the aims of this study are to tackle the issue of exposing one’s ‘aurah’ for a knee x-ray examination to take place and also to add insufficiency from the previous studies.

Matched MeSH terms: Textiles
Fulltext Removal of methyl orange dye by manganese/aluminium-layered double hydroxide

Mamat, M., Abdullah, M.A.A., Jaafar, A.M., Soh, S.K.C., Lee, C.E.

ASM Science Journal, 2018;11(101):105-113.
MyJurnal

As textile production flourishes nowadays, the amount of dyed wastewater entering the
water body has also increased. Dyes could have serious negative impacts to the environment
and also the human health, hence, they need to be removed from the water body. In this
study, layered double hydroxide (LDH) of manganese/aluminium (MnAl) was synthesised
to be used as a potential adsorbent to remove methyl orange (MO) dye due to its unique
lamellar structure which provides LDH with high anion adsorption and exchange ability.
MnAl was synthesized by using co-precipitation method and characterized by powder X-ray
diffraction (PXRD), Fourier-Transform Infrared Spectroscopy (FTIR), Inductively coupled
plasma atomic emission spectroscopy (ICP-AES) and Carbon, Hydrogen, Nitrogen, Sulphur
(CHNS) elemental analysers, and Accelerated Surface Area and Porosity Analyzer (ASAP).
Adsorption studies were conducted at different contact times and dosages of MnAl to evaluate
the performance of MnAl in removing MO from water. Kinetic and isotherm models were
tested using pseudo-first order, pseudo-second order, Langmuir isotherm and Freundlich
isotherm. MnAl LDH was found to be perfectly fitted into pseudo-second order and Langmuir
isotherm.

Matched MeSH terms: Textiles
Fulltext Effect of launderings on the pilling properties of cotton and polyester weft knitted fabrics

Noraqilah Mohd Azis, Siti Farhanim Sarani, Eryna Nasir, Najua Tulos

Journal of Academia Universiti Teknologi MARA Negeri Sembilan, 2018;6(2):38-45.
MyJurnal

Pilling is one of the fabric faults that originally found in knitted woolen goods especially made from soft twisted yarns. The rubbing action on loose fibres that is present on the fabric surface gives a high tendency to form pills which gives poor appearance to the fabric. This study was carried out to investigate the effect of repeated launderings on the propensity of pilling formation by using pill grade machine. The primary objective of this study was to determine the pilling behaviour of different types of weft knitted fabrics after a repeated number of laundering cycles. The study was conducted using two types of knitted fabrics; cotton and polyester with three types of knitted structures; interlock, 1x1 rib and plain jersey. The various number of laundering cycles were given on the fabrics and followed by 15,000 revolutions of ICI pilling box. The results showed that polyester fibre has better pilling resistance due to its exceptional strength, whilst in terms of fabric structure, plain jersey showed an excellent resistance. This is due to the higher density and compact structure that it possessed.

Matched MeSH terms: Textiles
Assessment of carbon footprint emissions and environmental concerns of solid waste treatment and disposal techniques; case study of Malaysia

Malakahmad A, Abualqumboz MS, Kutty SRM, Abunama TJ

Waste Manag, 2017 Dec;70:282-292.
PMID: 28935377 DOI: 10.1016/j.wasman.2017.08.044

Malaysian authorities has planned to minimize and stop when applicable unsanitary dumping of waste as it puts human health and the environment at elevated risk. Cost, energy and revenue are mostly adopted to draw the blueprint of upgrading municipal solid waste management system, while the carbon footprint emissions criterion rarely acts asa crucial factor. This study aims to alert Malaysian stakeholders on the uneven danger of carbon footprint emissions of waste technologies. Hence, three scenarios have been proposed and assessed mainly on the carbon footprint emissions using the 2006 IPCC methodology. The first scenario is waste dumping in sanitary landfills equipped with gas recovery system, while the second scenario includes anaerobic digestion of organics and recycling of recyclable wastes such as plastic, glass and textile wastes. The third scenario is waste incineration. Besides the carbon footprint emissions criterion, other environmental concerns were also examined. The results showed that the second scenario recorded the lowest carbon footprint emissions of 0.251t CO2 eq./t MSW while the third scenario had the highest emissions of 0.646t CO2 eq./t MSW. Additionally, the integration between anaerobic digestion and recycling techniques caused the highest avoided CO2 eq. emissions of 0.74t CO2 eq./t MSW. The net CO2 eq. emissions of the second scenario equaled -0.489t CO2 eq./t MSW due to energy recovery from the biogas and because of recycled plastic, glass and textile wastes that could replace usage of raw material. The outcomes also showed that the first scenario generates huge amount of leachate and hazardous air constituents. The study estimated that a ton of dumped waste inside the landfills generates approximately 0.88m3 of trace risky compounds and 0.188m3 of leachate. As for energy production, the results showed that the third scenario is capable of generating 639kWh/t MSW followed by the second scenario with 387.59kWh/t MSW. The first scenario produced 296.79kWh/t MSW. In conclusion, the outcomes of this study recommend an integrated scenario of anaerobic digestion and recycling techniques to be employed in Malaysia.

Matched MeSH terms: Textiles
Fulltext Novel, one-step synthesis of zwitterionic polymer nanoparticles via distillation-precipitation polymerization and its application for dye removal membrane

Ibrahim GPS, Isloor AM, Inamuddin, Asiri AM, Ismail N, Ismail AF, et al.

Sci Rep, 2017 Nov 21;7(1):15889.
PMID: 29162869 DOI: 10.1038/s41598-017-16131-9

In this work, poly(MBAAm-co-SBMA) zwitterionic polymer nanoparticles were synthesized in one-step via distillation-precipitation polymerization (DPP) and were characterized. [2-(methacryloyloxy)ethyl]dimethyl-(3-sulfopropyl)ammonium hydroxide (SBMA) as monomer and N, N'-methylene bis(acrylamide) (MBAAm) as cross-linker are used for the synthesis of nanoparticles. As far as our knowledge, this is the first such report on the synthesis of poly(MBAAm-co-SBMA) nanoparticles via DPP. The newly synthesized nanoparticles were further employed for the surface modification of polysulfone (PSF) hollow fiber membranes for dye removal. The modified hollow fiber membrane exhibited the improved permeability (56 L/ m2 h bar) and dye removal (>98% of Reactive Black 5 and >80.7% of Reactive orange 16) with the high permeation of salts. Therefore, the as-prepared membrane can have potential application in textile and industrial wastewater treatment.

Matched MeSH terms: Textiles
Polypyrrole-magnetite dispersive micro-solid-phase extraction combined with ultraviolet-visible spectrophotometry for the determination of rhodamine 6G and crystal violet in textile wastewater

Kamaruddin AF, Sanagi MM, Wan Ibrahim WA, Md Shukri DS, Abdul Keyon AS

J Sep Sci, 2017 Nov;40(21):4256-4263.
PMID: 28851082 DOI: 10.1002/jssc.201700659

Polypyrrole-magnetite dispersive micro-solid-phase extraction method combined with ultraviolet-visible spectrophotometry was developed for the determination of selected cationic dyes in textile wastewater. Polypyrrole-magnetite was used as adsorbent due to its thermal stability, magnetic properties, and ability to adsorb Rhodamine 6G and crystal violet. Dispersive micro-solid-phase extraction parameters were optimized, including sample pH, adsorbent amount, extraction time, and desorption solvent. The optimum polypyrrole-magnetite dispersive micro-solid phase-extraction conditions were sample pH 8, 60 mg polypyrrole-magnetite adsorbent, 5 min of extraction time, and acetonitrile as the desorption solvent. Under the optimized conditions, the polypyrrole-magnetite dispersive micro-solid-phase extraction with ultraviolet-visible method showed good linearity in the range of 0.05-7 mg/L (R2 > 0.9980). The method also showed a good limit of detection for the dyes (0.05 mg/L) and good analyte recoveries (97.4-111.3%) with relative standard deviations

Matched MeSH terms: Textiles
Pontamine fast scarlet 4B bifluorescence and measurements of cellulose microfibril angles

Thomas J, Idris NA, Collings DA

J Microsc, 2017 10;268(1):13-27.
PMID: 28654160 DOI: 10.1111/jmi.12582

Pontamine fast scarlet 4B is a red paper and textiles dye that has recently been introduced as a fluorescent probe for plant cell walls. Pontamine exhibits bifluorescence, or fluorescence dependent on the polarization of the excitation light: Because cellulose is aligned within the cell wall, pontamine-labelled cell walls exhibit variable fluorescence as the excitation polarization is modulated. Thus, bifluorescence measurements require polarized excitation that can be directly or indirectly modulated. In our confocal microscopy observations of various cellulose samples labelled with pontamine, we modulated excitation polarization either through sample rotation or by the confocal's scanfield rotation function. This variably rotated laser polarizations on Leica confocal microscopes, but not those from other makers. Beginning with samples with directly observable microfibril orientations, such as purified bacterial cellulose, the velamen of orchid roots and the inner S2 layer of radiata pine compression wood, we demonstrate that modelling the variations in pontamine fluorescence with a sine curve can be used to measure the known microfibril angles. We then measured average local microfibril angles in radiata pine samples, and showed similar microfibril angles in compression and normal (opposite) wood. Significantly, bifluorescence measurements might also be used to understand the degree of local cellulose alignment within the cell wall, as opposed to variations in the overall cellulose angle.

Matched MeSH terms: Textiles
Medium-chain-length poly-3-hydroxyalkanoates-carbon nanotubes composite anode enhances the performance of microbial fuel cell

Hindatu Y, Annuar MSM, Subramaniam R, Gumel AM

Bioprocess Biosyst Eng, 2017 Jun;40(6):919-928.
PMID: 28341913 DOI: 10.1007/s00449-017-1756-4

Insufficient power generation from a microbial fuel cell (MFC) hampers its progress towards utility-scale development. Electrode modification with biopolymeric materials could potentially address this issue. In this study, medium-chain-length poly-3-hydroxyalkanoates (PHA)/carbon nanotubes (C) composite (CPHA) was successfully applied to modify the surface of carbon cloth (CC) anode in MFC. Characterization of the functional groups on the anodic surface and its morphology was carried out. The CC-CPHA composite anode recorded maximum power density of 254 mW/m2, which was 15-53% higher than the MFC operated with CC-C (214 mW/m2) and pristine CC (119 mW/m2) as the anode in a double-chambered MFC operated with Escherichia coli as the biocatalyst. Electrochemical impedance spectroscopy and cyclic voltammetry showed that power enhancement was attributed to better electron transfer capability by the bacteria for the MFC setup with CC-CPHA anode.

Matched MeSH terms: Textiles
Fulltext Characterization of Textile-Insulated Capacitive Biosensors

Ng CL, Reaz MB

Sensors (Basel), 2017 Mar 12;17(3).
PMID: 28287493 DOI: 10.3390/s17030574

Capacitive biosensors are an emerging technology revolutionizing wearable sensing systems and personal healthcare devices. They are capable of continuously measuring bioelectrical signals from the human body while utilizing textiles as an insulator. Different textile types have their own unique properties that alter skin-electrode capacitance and the performance of capacitive biosensors. This paper aims to identify the best textile insulator to be used with capacitive biosensors by analysing the characteristics of 6 types of common textile materials (cotton, linen, rayon, nylon, polyester, and PVC-textile) while evaluating their impact on the performance of a capacitive biosensor. A textile-insulated capacitive (TEX-C) biosensor was developed and validated on 3 subjects. Experimental results revealed that higher skin-electrode capacitance of a TEX-C biosensor yields a lower noise floor and better signal quality. Natural fabric such as cotton and linen were the two best insulating materials to integrate with a capacitive biosensor. They yielded the lowest noise floor of 2 mV and achieved consistent electromyography (EMG) signals measurements throughout the performance test.

Matched MeSH terms: Textiles
Single chamber microbial fuel cell (SCMFC) with a cathodic microalgal biofilm: A preliminary assessment of the generation of bioelectricity and biodegradation of real dye textile wastewater

Logroño W, Pérez M, Urquizo G, Kadier A, Echeverría M, Recalde C, et al.

Chemosphere, 2017 Mar 01;176:378-388.
PMID: 28278426 DOI: 10.1016/j.chemosphere.2017.02.099

An air exposed single-chamber microbial fuel cell (SCMFC) using microalgal biocathodes was designed. The reactors were tested for the simultaneous biodegradation of real dye textile wastewater (RTW) and the generation of bioelectricity. The results of digital image processing revealed a maximum coverage area on the biocathodes by microalgal cells of 42%. The atmospheric and diffused CO2 could enable good algal growth and its immobilized operation on the cathode electrode. The biocathode-SCMFCs outperformed an open circuit voltage (OCV), which was 18%-43% higher than the control. Furthermore, the maximum volumetric power density achieved was 123.2 ± 27.5 mW m(-3). The system was suitable for the treatment of RTW and the removal/decrease of COD, colour and heavy metals. High removal efficiencies were observed in the SCMFCs for Zn (98%) and COD (92-98%), but the removal efficiencies were considerably lower for Cr (54-80%). We observed that this single chamber MFC simplifies a double chamber system. The bioelectrochemical performance was relatively low, but the treatment capacity of the system seems encouraging in contrast to previous studies. A proof-of-concept experiment demonstrated that the microalgal biocathode could operate in air exposed conditions, seems to be a promising alternative to a Pt cathode and is an efficient and cost-effective approach to improve the performance of single chamber MFCs.

Matched MeSH terms: Textiles
Fulltext Investigating the effect of different Weft densities and draw in plan on physical properties and Seam strength of Woven plain fabrics

Nurul Syazwani Abdul Latif, Suzaini Abdul Ghani

Pertanika Journal of Science & Technology, 2017;25(108):19-28.
MyJurnal

Weft density and draw in plan play an important role since they affect physical properties such as fabric weight, cloth cover factor as well as seam strength. Weft density refers to the amount of weft yarn in one inch. Meanwhile, draw in plan refers to the amount of heald shaft used and the order of warp yarn through the heald. In this study, plain woven fabrics were produced by using Sulzer Rapier Loom Machine. There were two different types of weft density used which were 15 and 20 weft per centimeter (wpcm) and four draws in plan: pointed, straight, broken and broken mirror. Seams were constructed by using plain seam of Ssa-1, four stitches of stitch density and 301 lockstitches for stitch type. Subsequently, the fabric samples were tested on seam strength by using Testometric tester. As a result of this study, it is proven that weft density and draw in plan of woven plain fabric are parameters that affect the seam strength and seam efficiency. The highest increase in percentage of seam strength was obtained from straight draw in plan which increases up to 17.19% from 15wpcm to 20wpcm. Meanwhile, broken draw in plan has the lowest increase percentage for seam strength which is 6.46%. Furthermore, seam efficiency also shows straight draw in plan gives good fabric durability compared to others. Lastly, it also shows broken draw in plan has no significant effect on fabric tensile strength and seam strength.

Matched MeSH terms: Textiles
An efficient and economical treatment for batik textile wastewater containing high levels of silicate and organic pollutants using a sequential process of acidification, magnesium oxide, and palm shell-based activated carbon application

Birgani PM, Ranjbar N, Abdullah RC, Wong KT, Lee G, Ibrahim S, et al.

J Environ Manage, 2016 Dec 15;184(Pt 2):229-239.
PMID: 27717677 DOI: 10.1016/j.jenvman.2016.09.066

Considering the chemical properties of batik effluents, an efficient and economical treatment process was established to treat batik wastewater containing not only high levels of Si and chemical oxygen demand (COD), but also toxic heavy metals. After mixing the effluents obtained from the boiling and soaking steps in the batik process, acidification using concentrated hydrochloric acid (conc. HCl) was conducted to polymerize the silicate under acidic conditions. Consequently, sludge was produced and floated. XRD and FT-IR analyses showed that wax molecules were coordinated by hydrogen bonding with silica (SiO2). The acidification process removed ∼78-95% of COD and ∼45-50% of Si, depending on the pH. In the next stage, magnesium oxide (MgO) was applied to remove heavy metals completely and almost 90% of the Si in the liquid phase. During this step, about 70% of COD was removed in the hydrogel that arose as a consequence of the crosslinking characteristics of the formed nano-composite, such as magnesium silicate or montmorillonite. The hydrogel was composed mainly of waxes with polymeric properties. Then, the remaining Si (∼300 mg/L) in the wastewater combined with the effluents from the rinsing steps was further treated using 50 mg/L MgO. As a final step, palm-shell activated carbon (PSAC) was used to remove the remaining COD to

Matched MeSH terms: Textiles*
Bioremediation and Detoxification of the Textile Wastewater with Membrane Bioreactor Using the White-rot Fungus and Reuse of Wastewater

Hossain K, Quaik S, Ismail N, Rafatullah M, Avasan M, Shaik R

Iran J Biotechnol, 2016 Sep;14(3):154-162.
PMID: 28959331 DOI: 10.15171/ijb.1216

BACKGROUND: Application of membrane technology to wastewater treatment has expanded over the last decades due to increasingly stringent legislation, greater opportunities for water reuse/recycling processes and continuing advancement in membrane technology.
OBJECTIVES: In the present study, a bench-scale submerged microfiltration membrane bioreactor (MBR) was used to assess the treatment of textile wastewater.
MATERIALS AND METHODS: The decolorization capacity of white-rot fungus coriolus versicolor was confirmed through agar plate and liquid batch studies. The temperature and pH of the reactor were controlled at 29±1°C and 4.5±2, respectively. The bioreactor was operated with an average flux of 0.05 m.d(-1) (HRT=15hrs) for a month.
RESULTS: Extensive growth of fungi and their attachment to the membrane led to its fouling and associated increase of the transmembrane pressure requiring a periodic withdrawal of sludge and membrane cleaning. However, stable decoloration activity (approx. 98%), BOD (40-50%), COD (50-67%) and total organic carbon (TOC) removal (>95%) was achieved using the entire system (fungi + membrane), while the contribution of the fungi culture alone for TOC removal, as indicated by the quality of the reactor supernatant, was 35-50% and 70%, respectively.
CONCLUSIONS: The treated wastewater quality satisfied the requirement of water quality for dyeing and finishing process excluding light coloration. Therefore, textile wastewater reclamation and reuse is a promising alternative, which can both conserve or supplement the available water resource and reduce or eliminate the environmental pollution.

Matched MeSH terms: Textiles
Fulltext Strengthening of RC Beams Using Externally Bonded Reinforcement Combined with Near-Surface Mounted Technique

Darain KMU, Jumaat MZ, Shukri AA, Obaydullah M, Huda MN, Hosen MA, et al.

Polymers (Basel), 2016 Jul 19;8(7).
PMID: 30974542 DOI: 10.3390/polym8070261

This study investigates the flexural behaviour of reinforced concrete (RC) beams strengthened through the combined externally bonded and near-surface mounted (CEBNSM) technique. The externally bonded reinforcement (EBR) and near-surface mounted (NSM) techniques are popular strengthening solutions, although these methods often demonstrate premature debonding failure. The proposed CEBNSM technique increases the bond area of the concrete⁻carbon fibre reinforced polymer (CFRP) interface, which can delay the debonding failure. This technique is appropriate when any structure has a narrow cross-sectional width or is in need of additional flexural capacity that an individual technique or material cannot attain. An experimental test matrix was designed with one control and five strengthened RC beams to verify the performance of the proposed technique. The strengthening materials were CFRP bar as NSM reinforcement combined with CFRP fabric as EBR material. The test variables were the diameter of the NSM bars (8 and 10 mm), the thickness of the CFRP fabrics (one and two layers) and the U-wrap anchorage. The strengthened beams showed enhancement of ultimate load capacity, stiffness, cracking behaviour, and strain compatibility. The ultimate capacity of the CEBNSM-strengthened beams increased from 71% to 105% compared to that of the control beam. A simulation method based on the moment-rotation approach was also presented to predict the behaviour of CEBNSM-strengthened RC beams.

Matched MeSH terms: Textiles
Fulltext Formability Analysis of Bamboo Fabric Reinforced Poly (Lactic) Acid Composites

M R NF, Jayaraman K, Bhattacharyya D

Materials (Basel), 2016 Jul 02;9(7).
PMID: 28773662 DOI: 10.3390/ma9070539

Poly (lactic) acid (PLA) composites have made their way into various applications that may require thermoforming to produce 3D shapes. Wrinkles are common in many forming processes and identification of the forming parameters to prevent them in the useful part of the mechanical component is a key consideration. Better prediction of such defects helps to significantly reduce the time required for a tooling design process. The purpose of the experiment discussed here is to investigate the effects of different test parameters on the occurrence of deformations during sheet forming of double curvature shapes with bamboo fabric reinforced-PLA composites. The results demonstrated that the domes formed using hot tooling conditions were better in quality than those formed using cold tooling conditions. Wrinkles were more profound in the warp direction of the composite domes compared to the weft direction. Grid Strain Analysis (GSA) identifies the regions of severe deformation and provides useful information regarding the optimisation of processing parameters.

Matched MeSH terms: Textiles
Work Ability and Its Related Factors Among Workers in Small and Medium Enterprises: Comparison Among Four ASEAN Countries

Kaewboonchoo O, Isahak M, Susilowati I, Phuong TN, Morioka I, Harncharoen K, et al.

Asia Pac J Public Health, 2016 Jul;28(5):438-49.
PMID: 27273897 DOI: 10.1177/1010539516651957

Work ability is related to many factors that might influence one's capacity to work. This study aimed to examine the work ability and its related factors among small and medium enterprises (SME) workers in 4 Association of Southeast Asian Nations (ASEAN) countries. The participants in this study included 2098 workers from food and textile industries in Indonesia, Malaysia, Thailand, and Vietnam. A cross-sectional survey of anonymous self-administrated questionnaire was designed to collect information on sociodemographic factors, work environment and ergonomic condition, musculoskeletal disorders, and work ability. Bivariate correlation coefficient and multiple linear regression analyses were used to predict the work ability. Results of this study confirm that work ability in 4 ASEAN countries was similar to that in European countries, and that the sociodemographic factors, work environment and ergonomic condition, and musculoskeletal disorder (MSD) were associated with work ability. These factors are important for considering occupational health and safety policy to promote work ability in food, textile, and other SME workers.

Matched MeSH terms: Textiles
Electrocoagulation using a rotated anode: A novel reactor design for textile wastewater treatment

Naje AS, Chelliapan S, Zakaria Z, Abbas SA

J Environ Manage, 2016 Jul 1;176:34-44.
PMID: 27039362 DOI: 10.1016/j.jenvman.2016.03.034

This paper investigates the optimum operational conditions of a novel rotated bed electrocoagulation (EC) reactor for the treatment of textile wastewater. The effect of various operational parameters such as rotational speed, current density (CD), operational time (RT), pH, temperature, and inter-electrode distance (IED) on the pollutant removal efficiency were examined. In addition, the consumption of aluminum (Al) and electrical energy, as well as operating costs at optimum conditions were also calculated. The results indicated that the optimum conditions for the treatment of textile wastewater were achieved at CD = 4 mA/cm(2), RT = 10 min, rotational speed = 150 rpm, pH = 4.57, temperature = 25 °C, and IED = 1 cm. The electrode consumption, energy consumption, and operating costs were 0.038 kg/m(3), 4.66 kWh/m(3) and 0.44 US$/m(3), respectively. The removal efficiencies of chemical oxygen demand (COD), biological oxygen demand (BOD), total suspended solid (TSS), turbidity and color were 97.10%, 95.55%, 98%, 96% and 98.50%, respectively, at the first 10 min of reaction time, while the phenol compound of the wastewater was almost entirely removed (99.99%). The experimental results confirm that the new reactor design with rotated anode impellers and cathode rings provided high treatment efficiency at a reduced reaction time and with lower energy consumption.

Matched MeSH terms: Textiles
Fulltext Occupational exposure to textile dust increases the risk of rheumatoid arthritis: results from a Malaysian population-based case-control study

Too CL, Muhamad NA, Ilar A, Padyukov L, Alfredsson L, Klareskog L, et al.

Ann Rheum Dis, 2016 06;75(6):997-1002.
PMID: 26681695 DOI: 10.1136/annrheumdis-2015-208278

OBJECTIVES: Lung exposures including cigarette smoking and silica exposure are associated with the risk of rheumatoid arthritis (RA). We investigated the association between textile dust exposure and the risk of RA in the Malaysian population, with a focus on women who rarely smoke.

METHODS: Data from the Malaysian Epidemiological Investigation of Rheumatoid Arthritis population-based case-control study involving 910 female early RA cases and 910 female age-matched controls were analysed. Self-reported information on ever/never occupationally exposed to textile dust was used to estimate the risk of developing anti-citrullinated protein antibody (ACPA)-positive and ACPA-negative RA. Interaction between textile dust and the human leucocyte antigen DR β-1 (HLA-DRB1) shared epitope (SE) was evaluated by calculating the attributable proportion due to interaction (AP), with 95% CI.

RESULTS: Occupational exposure to textile dust was significantly associated with an increased risk of developing RA in the Malaysian female population (OR 2.8, 95% CI 1.6 to 5.2). The association between occupational exposure to textile dust and risk of RA was uniformly observed for the ACPA-positive RA (OR 2.5, 95% CI 1.3 to 4.8) and ACPA-negative RA (OR 3.5, 95% CI 1.7 to 7.0) subsets, respectively. We observed a significant interaction between exposure to occupational textile dust and HLA-DRB1 SE alleles regarding the risk of ACPA-positive RA (OR for double exposed: 39.1, 95% CI 5.1 to 297.5; AP: 0.8, 95% CI 0.5 to 1.2).

CONCLUSIONS: This is the first study demonstrating that textile dust exposure is associated with an increased risk for RA. In addition, a gene-environment interaction between HLA-DRB1 SE and textile dust exposure provides a high risk for ACPA-positive RA.

Matched MeSH terms: Textiles/adverse effects*
Biotransformation studies of cresol red by Absidia spinosa M15

Kristanti RA, Fikri Ahmad Zubir MM, Hadibarata T

J Environ Manage, 2016 May 1;172:107-11.
PMID: 26922501 DOI: 10.1016/j.jenvman.2015.11.017

Cresol Red, a commercial dye that used widely to color nylon, wool, cotton, and polyacrylonitrile-modified nylon in the massive textile manufacture is toxic recalcitrant. Absidia spinosa M15, a novel fungal strain isolated from a tropical rain forest, was found to decolorize Cresol Red 65% within 30 d under agitation condition. UV-Vis spectroscopy, TLC analysis and mass spectra of samples after decolorization process in culture medium confirmed final decolorization of Cresol Red. Two metabolites were identified in the treated medium: benzeneacetic acid (tR 9.6 min and m/z 136) and benzoic acid (tR 5.7 min and m/z 122). Laccase showed the significant activity (133.8 U/L) in biomass obtained at the end of experiment demonstrates role of the enzyme in the decolorization process.

Matched MeSH terms: Textiles

Filters

Please provide feedback to Administrator (afdal@afpm.org.my)

External Links