MyMedR

Displaying publications 41 - 60 of 172 in total

Abstract:

Sort:

Mechanical and microstructural properties of high calcium fly ash one-part geopolymer cement made with granular activator

Mohammed BS, Haruna S, Wahab MMA, Liew MS, Haruna A

Heliyon, 2019 Sep;5(9):e02255.
PMID: 31687531 DOI: 10.1016/j.heliyon.2019.e02255

In this present experimental study, geopolymer cement is developed using high calcium fly ash and used in the production of one-part alkali-activated binders. At 8-16 percent of the total precursor materials, the HCFA was activated with anhydrous sodium metasilicate powder and cured in ambient condition. Five mixtures of one-part geopolymer paste were intended at a steady w/b proportion. Density, flowability, setting time, compressive strength, splitting tensile strength and molar ratio impact were envisaged. It was observed that the setting time of the designed one-part geopolymer paste decreases with higher activator content. The experimental findings showed that the resistance of one-part geopolymer cement paste increases with comparatively greater activator content. However, raising the granular activator beyond 12 percent by fly ash weight decreases the strength and workability of the established one-part geopolymer cement. The optimum mix by weight of the fly ash was discovered to be 12 percent (i.e. 6 percent Na2O). At 28 days of curing, one-part alkali-activated paste recorded the greatest compressive strength of almost 50 MPa. The density of the one-part geopolymer paste is nearly the same regardless of the mixes. Microstructural assessment by FESEM, FTIR and XRD has shown that the established geopolymer paste includes quartz, pyrrhotite, aluminosilicate sodium and hydrate gels of calcium aluminosilicate. Based on the experimental information acquired, it can be deduced that the strength growth of one-part geopolymer cement is similar to that of Portland cement.

Matched MeSH terms: Aluminum Silicates; Silicates
Fulltext Development of Nano-SiO2 and Bentonite-Based Mortars for Corrosion Protection of Reinforcing Steel

Karunarathne VK, Paul SC, Šavija B

Materials (Basel), 2019 Aug 17;12(16).
PMID: 31426501 DOI: 10.3390/ma12162622

In this study, the use of nano-silica (nano-SiO2) and bentonite as mortar additives for combating reinforcement corrosion is reported. More specifically, these materials were used as additives in ordinary Portland cement (OPC)/fly ash blended mortars in different amounts. The effects of nano-silica and bentonite addition on compressive strength of mortars at different ages was tested. Accelerated corrosion testing was used to assess the corrosion resistance of reinforced mortar specimens containing different amounts of nano-silica and bentonite. It was found that the specimens containing nano-SiO2 not only had higher compressive strength, but also showed lower steel mass loss due to corrosion compared to reference specimens. However, this was accompanied by a small reduction in workability (for a constant water to binder ratio). Mortar mixtures with 4% of nano-silica were found to have optimal performance in terms of compressive strength and corrosion resistance. Control specimens (OPC/fly ash mortars without any additives) showed low early age strength and low corrosion resistance compared to specimens containing nano-SiO2 and bentonite. In addition, samples from selected mixtures were analyzed using scanning electron microscopy (SEM) and energy-dispersive X-ray spectroscopy (EDX). Finally, the influence of Ca/Si ratio of the calcium silicate hydrate (C-S-H) in different specimens on the compressive strength is discussed. In general, the study showed that the addition of nano-silica (and to a lesser extent bentonite) can result in higher strength and corrosion resistance compared to control specimens. Furthermore, the addition of nano-SiO2 can be used to offset the negative effect of fly ash on early age strength development.

Matched MeSH terms: Silicates
Fulltext Fission-track data and U-Pb dating of granites from Cameron Highland, Peninsular Malaysia: Evidence to comprehend exhumation episodes

Kassa S, Tsegab H, Sum CW, CheeMeng C

Data Brief, 2019 Aug;25:104162.
PMID: 31317063 DOI: 10.1016/j.dib.2019.104162

Fission tracks are linear trails of intense radiation damage in the crystal structure of a mineral, produced by spontaneous fissioning of uranium-238 (238U) atoms. Detail information on the low-temperature thermal histories of rocks, below∼120 °C for tracks in apatite and below∼350 °C for zircon, can be provided by Fission-track (FT) analysis. The purpose of this article is to present apatite and zircon fission-track data, and U-Pb granite ages that provide information about the cooling histories of a rock which can be crucial in comprehending the exhumation episodes of the study area, in particular, and the region, in general. Granite samples were collected along the same vertical profile at different elevation, 178-944 m.a.s.l. These samples were used to determine Fission-Track and crystallization ages. HeFTy software was employed to interpret the cooling histories of the samples using forward and inverse models. The inverse model was an approach of reproducing the observed data, and it was carried out only for fission-track data from the apatite grains. And it was constructed after generating a number of forward models, where in each of these models the predicted apatite fission-track parameters were compared to the measured values. The apatite fission track (AFT) and zircon fission track (ZFT) data indicated expected age trends, i.e. the older ages at higher elevations and the younger ages at lower elevations. Similarly, the data shows that the apatite and zircon FT ages appear younger than the age of the rock crystallization. The U-Pb age in zircon consistently suggest the age of the granite is Late Triassic.

Matched MeSH terms: Silicates
Why does vacuum drive to the loading of halloysite nanotubes? The key role of water confinement

Lisuzzo L, Cavallaro G, Pasbakhsh P, Milioto S, Lazzara G

J Colloid Interface Sci, 2019 Jul 01;547:361-369.
PMID: 30974251 DOI: 10.1016/j.jcis.2019.04.012

The filling of halloysite nanotubes with active compounds solubilized in aqueous solvent was investigated theoretically and experimentally. Based on Knudsen thermogravimetric data, we demonstrated the water confinement within the cavity of halloysite. This process is crucial to properly describe the driving mechanism of halloysite loading. In addition, Knudsen thermogravimetric experiments were conducted on kaolinite nanoplates as well as on halloysite nanotubes modified with an anionic surfactant (sodium dodecanoate) in order to explore the influence of both the nanoparticle morphology and the hydrophobic/hydrophilic character of the lumen on the confinement phenomenon. The analysis of the desorption isotherms allowed us to determine the water adsorption properties of the investigated nanoclays. The pore sizes of the nanotubes' lumen was determined by combining the vapor pressure of the confined water with the nanoparticles wettability, which was studied through contact angle measurements. The thermodynamic description of the water confinement inside the lumen was correlated to the influence of the vacuum pumping in the experimental loading of halloysite. Metoprolol tartrate, salicylic acid and malonic acid were selected as anionic guest molecules for the experimental filling of the positively charged halloysite lumen. According to the filling mechanism induced by the water confinement, the vacuum operation and the reduced pressure enhanced the loading of halloysite nanotubes for all the investigated bioactive compounds. This work represents a further and crucial step for the development of halloysite based nanocarriers being that the filling mechanism of the nanotube's cavity from aqueous dispersions was described according to the water confinement process.

Matched MeSH terms: Aluminum Silicates
Environmental evaluation and nano-mineralogical study of fresh and unsaturated weathered coal fly ashes

Akinyemi SA, Gitari WM, Petrik LF, Nyakuma BB, Hower JC, Ward CR, et al.

Sci Total Environ, 2019 May 01;663:177-188.
PMID: 30711584 DOI: 10.1016/j.scitotenv.2019.01.308

Coal combustion and the disposal of combustion wastes emit enormous quantities of nano-sized particles that pose significant health concerns on exposure, particularly in unindustrialized countries. Samples of fresh and weathered class F fly ash were analysed through various techniques including X-ray fluorescence (XRF), X-ray diffraction (XRD), focused ion beam scanning electron microscopy (FIB-SEM), field-emission gun scanning electron microscopy (FE-SEM), high-resolution transmission electron microscopy (HR-TEM) coupled with energy dispersive x-ray spectroscopy (EDS), and Raman Spectroscopy. The imaging techniques showed that the fresh and weathered coal fly ash nanoparticles (CFA-NPs) are mostly spherical shaped. The crystalline phases detected were quartz, mullite, ettringite, calcite, maghemite, hematite, gypsum, magnetite, clay residues, and sulphides. The most abundant crystalline phases were quartz mixed with Al-Fe-Si-K-Ti-O-amorphous phases whereas mullite was detected in several amorphous phases of Al, Fe, Ca, Si, O, K, Mg, Mn, and P. The analyses revealed that CFA-NPs are 5-500 nm in diameter and encapsulate several potentially hazardous elements (PHEs). The carbon species were detected as 5-50 nm carbon nanoballs of graphitic layers and massive fullerenes. Lastly, the aspects of health risks related to exposure to some detected ambient nanoparticles are also discussed.

Matched MeSH terms: Aluminum Silicates
Efficacy of Biodentine and Mineral Trioxide Aggregate in Primary Molar Pulpotomies-A Systematic Review and Meta-Analysis With Trial Sequential Analysis of Randomized Clinical Trials

Nagendrababu V, Pulikkotil SJ, Veettil SK, Jinatongthai P, Gutmann JL

J Evid Based Dent Pract, 2019 03;19(1):17-27.
PMID: 30926099 DOI: 10.1016/j.jebdp.2018.05.002

OBJECTIVES: Pulpotomy is the favored treatment for pulp exposure in carious primary teeth. This review aimed to compare the success rates of biodentine (BD) and mineral trioxide aggregate (MTA) pulpotomies in primary molars using meta-analysis (MA) and trial sequential analysis (TSA) and also to assess the quality of the results by Grading of Recommendations, Assessment, Development and Evaluation (GRADE).
METHODS: PubMed, EBSCOhost, and Scopus databases were searched. Additional searching was performed in clinical trial registry, reference lists of systematic reviews, and textbooks. Randomized clinical trials (RCTs) published in the English language through October 2017 comparing the success of pulpotomies in vital primary molars with a follow-up of at least 6 months were selected. Study selection, data extraction, and risk of bias assessment were performed. MA by random effects model, TSA, and GRADE were performed.
RESULTS: Eight RCTs (n = 474) were included. Two RCTs had low risk of bias. No significant difference was observed between MTA and BD in clinical success at 6 months (risk ratio [RR], 1.00; 95% confidence interval [95% CI], 0.97-1.02; I2 = 0%), 12 months (RR, 1.00; 95% CI, 0.96-1.05; I2 = 0%), and 18 months (RR, 1.00; 95% CI, 0.93-1.08; I2 = 0%). No difference was observed in radiographic success at follow-up of 6 months (RR, 0.99; 95% CI, 0.96-1.02; I2 = 0%), 12 months (RR, 1.02; 95% CI, 0.47-2.21; I2 = 0%), and 18 months (RR, 1.02; 95% CI, 0.91-1.15; I2 = 0%). TSA indicated lack of firm evidence for the results of the meta-analytic outcomes on clinical and radiographic success. GRADE assessed the evidence from the MA comparing the effect of MTA and BD in pulpotomy to be of low quality.
CONCLUSION: BD and MTA have similar clinical and radiographic success rates based on limited and low-quality evidence. Future high-quality RCTs between MTA and BD is required to confirm the evidence.

Matched MeSH terms: Silicates
Physicochemical characteristics of microbial content in a modified anaerobic inclining-baffled reactor (MAI-BR) treating recycled paper mill effluent (RPME)

Zwain HM, Chang SM, Dahlan I

Prep Biochem Biotechnol, 2019;49(4):344-351.
PMID: 30712465 DOI: 10.1080/10826068.2019.1566144

Microbial content formed in bioreactors plays a significant role in the anaerobic process. Therefore, the physicochemical characteristics of microbial content in a modified anaerobic inclining-baffled reactor (MAI-BR) treating recycled paper mill effluent (RPME) were investigated using Fourier transform infrared (FTIR), X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), thermogravimetric (TG), and derivative thermogravimetric (DTG) analyses, scanning electron microscopy-energy dispersive X-ray spectroscopy (SEM-EDS), Brunauer-Emmett-Teller (BET), and surface area analyzer. FTIR spectra revealed that the microbial content had stronger characteristic peaks corresponding to alcohols, water, lipids carbohydrates, proteins, and mineral compounds. Calcite, muscovite, and lepidolite were the prevalent mineral phases found by XRD analysis. The elemental of these minerals like C, Ca, N, O, and Si was confirmed by XPS results. The microbial content samples from each compartment showed similar thermal behavior. SEM images showed that straight rod-shaped and Methanosaeta-like microorganisms were predominant, whereas C, O, and Ca were noticed by EDS on the surface of granules. The BET surface areas and pores of granules are found to decline throughout the reactor's compartment, where Compartment 1 had the largest values. Thus, the findings of this study establish further understanding of the physicochemical properties of microbial content formed in MAI-BR during the RPME treatment.

Matched MeSH terms: Aluminum Silicates
Fulltext Dataset on structure and mechanical properties of electrospun polyacrylonitrile nanofibrous mesh reinforced by halloysite nanotubes

Goh KL, Makaremi M, Pasbakhsh P, De Silva R, Zivkovic V

Data Brief, 2018 Dec;21:2170-2178.
PMID: 30555856 DOI: 10.1016/j.dib.2018.11.039

The mechanical properties of electrospun polyacrylonitrile (PAN)-based membranes for ultrafiltration, such as oil-water separation and heavy metals from water, are often characterised in the dry state but little is known about the membrane properties in the hydrated state. This dataset comprised mechanical properties and structure-related properties of electrospun PAN-based membranes. The mechanical dataset described the yield strength and strain, stiffness, resilience energy, fracture strength, strain at fracture and fracture toughness of electrospun neat PAN and halloysite nanotube (HNT) reinforced PAN membranes in both hydrated and dry states. The data related to the hydrated state were derived from direct measurements of the mechanical properties of the PAN-based membrane using a novel environmental micromechanical tester. The structure-related dataset comprised electron micrographs and quantitative measurements (fibre diameter and pore diameter) derived from the micrographs. For further interpretation and discussion of the dataset, the reader is referred to the research data article, "Direct measurement of the elasticity and fracture properties of electrospun polyacrylonitrile/halloysite fibrous mesh in water" (Govindasamy et al., 2014).

Matched MeSH terms: Aluminum Silicates
Fulltext Data on organochlorine concentration levels in soil of lowland paddy field, Kelantan, Malaysia

Osman BE, Khalik WMAWM

Data Brief, 2018 Oct;20:999-1003.
PMID: 30225314 DOI: 10.1016/j.dib.2018.08.178

The main goal of this research work is to measure the concentration levels of organochlorine residue in soil. The potential health risk of this pollutant on human was also determined. 10 samples were taken from a lowland paddy field situated in Kelantan, Malaysia. Physical parameters namely soil pH, organic carbon content, water content and particle size were identified to evaluate the quality of soil from the agriculture site. Soxhlet extraction and florisil clean-up process were applied to isolate 10 targeted organochlorine compounds prior to the final determination using a gas chromatography-electron capture detector. Soil from the lowland has characteristics such as slightly acidic, low organic carbon content, high water content and texture dominated by the sandy type. Concentration levels of six detected organochlorine pesticides were calculated in µg/kg. Hazard quotient value in all samples was less than the acceptable risk level HQ ≤ 1, thus reflecting the status of soil in the subjected area as unlikely to pose any adverse health effects.

Matched MeSH terms: Magnesium Silicates
Fulltext Postoperative assessment of diode laser zinc oxide eugenol and mineral trioxide aggregate pulpotomy procedures in children: A comparative clinical study

Pratima B, Chandan GD, Nidhi T, Nitish I, Sankriti M, Nagaveni S, et al.

J Indian Soc Pedod Prev Dent, 2018 9 25;36(3):308-314.
PMID: 30246755 DOI: 10.4103/JISPPD.JISPPD_1132_17

Aim: The present study is an attempt to compare and evaluate postoperative assessment of diode laser zinc oxide eugenol (ZOE) pulpotomy and diode laser mineral trioxide aggregate (MTA) pulpotomy procedures in children.
Materials and Methods: Forty carious primary molars indicated for pulpotomy within the age group of 4-9 years were selected and divided into two groups of 20 each using simple randomization, Group 1: Diode laser MTA and Group 2: Diode laser ZOE pulpotomy. The teeth were evaluated clinically for 1 year at 3, 6, and 12 months interval and radiologically for 6 and 12 months.
Results: Clinically and radiographically, 100% teeth treated with diode laser MTA and 94% treated with diode laser ZOE were considered successful after 12-month follow-up interval. No significant difference was seen between two groups.
Conclusion: Despite the success rate, the cost factor of diode laser and MTA could be the limiting factor in its judicious use in pulpotomy procedure.

Matched MeSH terms: Silicates/therapeutic use*
Effect of root canal irrigation protocols on the dislocation resistance of mineral trioxide aggregate-based materials: A systematic review of laboratory studies

Neelakantan P, Ahmed HMA, Wong MCM, Matinlinna JP, Cheung GSP

Int Endod J, 2018 Aug;51(8):847-861.
PMID: 29377170 DOI: 10.1111/iej.12898

The aim of this systematic review was to address the question: Do different irrigating protocols have an impact on the dislocation resistance of mineral trioxide aggregate (MTA)-based materials? The review was performed using a well-defined search strategy in three databases (PubMed, Scopus, Web of Science) to include laboratory studies performed between January 1995 and May 2017, in accordance with PRISMA guidelines. Two reviewers analysed the papers, assessed the risk of bias and extracted data on teeth used, sample size, size of root canal preparation, type of MTA-based material, irrigants, canal filling method, storage method and duration, region of roots and the parameters of push-out testing (slice thickness, plunger dimensions and plunger loading direction), the main results and dislocation resistance values (in MPa). From 255 studies, 27 were included for full-text analysis. Eight papers that met the inclusion criteria were included in this review. There was a wide variation in dislocation resistance due to differences in irrigation sequence, time and concentration of irrigants, storage method and duration, and the parameters of push-out bond strength testing. A meta-analysis was not done but qualitative synthesis of the included studies was performed. No definitive conclusion could be drawn to evaluate the effect of irrigation protocols on dislocation resistance of MTA-based materials. Recommendations have been provided for standardized testing methods and reporting of future studies, so as to obtain clinically relevant information and to understand the effects of irrigating protocols on root canal sealers and their interactions with the dentine walls of root canals.

Matched MeSH terms: Silicates/pharmacology*
Fulltext Evidence of Enriched, Hadean Mantle Reservoir from 4.2-4.0 Ga zircon xenocrysts from Paleoarchean TTGs of the Singhbhum Craton, Eastern India

Chaudhuri T, Wan Y, Mazumder R, Ma M, Liu D

Sci Rep, 2018 May 04;8(1):7069.
PMID: 29728630 DOI: 10.1038/s41598-018-25494-6

Sensitive High-Resolution Ion Microprobe (SHRIMP) U-Pb analyses of zircons from Paleoarchean (~3.4 Ga) tonalite-gneiss called the Older Metamorphic Tonalitic Gneiss (OMTG) from the Champua area of the Singhbhum Craton, India, reveal 4.24-4.03 Ga xenocrystic zircons, suggesting that the OMTG records the hitherto unknown oldest precursor of Hadean age reported in India. Hf isotopic analyses of the Hadean xenocrysts yield unradiogenic 176Hf/177Hfinitial compositions (0.27995 ± 0.0009 to 0.28001 ± 0.0007; ɛHf[t] = -2.5 to -5.2) indicating that an enriched reservoir existed during Hadean eon in the Singhbhum cratonic mantle. Time integrated ɛHf[t] compositional array of the Hadean xenocrysts indicates a mafic protolith with 176Lu/177Hf ratio of ∼0.019 that was reworked during ∼4.2-4.0 Ga. This also suggests that separation of such an enriched reservoir from chondritic mantle took place at 4.5 ± 0.19 Ga. However, more radiogenic yet subchondritic compositions of ∼3.67 Ga (average 176Hf/177Hfinitial 0.28024 ± 0.00007) and ~3.4 Ga zircons (average 176Hf/177Hfinitial = 0.28053 ± 0.00003) from the same OMTG samples and two other Paleoarchean TTGs dated at ~3.4 Ga and ~3.3 Ga (average 176Hf/177Hfinitial is 0.28057 ± 0.00008 and 0.28060 ± 0.00003), respectively, corroborate that the enriched Hadean reservoir subsequently underwent mixing with mantle-derived juvenile magma during the Eo-Paleoarchean.

Matched MeSH terms: Silicates
Fulltext Removal of metal ions and humic acids through polyetherimide membrane with grafted bentonite clay

Hebbar RS, Isloor AM, Prabhu B, Inamuddin, Asiri AM, Ismail AF

Sci Rep, 2018 03 16;8(1):4665.
PMID: 29549259 DOI: 10.1038/s41598-018-22837-1

Functional surfaces and polymers with branched structures have a major impact on physicochemical properties and performance of membrane materials. With the aim of greener approach for enhancement of permeation, fouling resistance and detrimental heavy metal ion rejection capacity of polyetherimide membrane, novel grafting of poly (4-styrenesulfonate) brushes on low cost, natural bentonite was carried out via distillation-precipitation polymerisation method and employed as a performance modifier. It has been demonstrated that, modified bentonite clay exhibited significant improvement in the hydrophilicity, porosity, and water uptake capacity with 3 wt. % of additive dosage. SEM and AFM analysis showed the increase in macrovoides and surface roughness with increased additive concentration. Moreover, the inclusion of modified bentonite displayed an increase in permeation rate and high anti-irreversible fouling properties with reversible fouling ratio of 75.6%. The humic acid rejection study revealed that, PEM-3 membrane having rejection efficiency up to 87.6% and foulants can be easily removed by simple hydraulic cleaning. Further, nanocomposite membranes can be significantly employed for the removal of hazardous heavy metal ions with a rejection rate of 80% and its tentative mechanism was discussed. Conspicuously, bentonite clay-bearing poly (4-styrenesulfonate) brushes are having a synergistic effect on physicochemical properties of nanocomposite membrane to enhance the performance in real field applications.

Matched MeSH terms: Aluminum Silicates
Removal of lead and bisphenol A using magnesium silicate impregnated palm-shell waste powdered activated carbon: Comparative studies on single and binary pollutant adsorption

Choong CE, Ibrahim S, Yoon Y, Jang M

Ecotoxicol Environ Saf, 2018 Feb;148:142-151.
PMID: 29040822 DOI: 10.1016/j.ecoenv.2017.10.025

In this work, palm shell waste powder activated carbon coated by magnesium silicate (PPAC-MS) were synthesized by the impregnation of magnesium silicate (MgSiO3) using economical material (silicon dioxide powder) via mild hydrothermal approach for the first time. As an effective adsorbent, PPAC-MS simultaneously removes BPA and Pb(II) in single and binary mode. Surprisingly, PPAC-MS exhibited a homogeneous thin plate mesh-like structure, as well as meso- and macropores with a high surface area of 772.1m2g-1. Due to its specific morphological characteristics, PPAC-MS had adsorption capacities of Pb(II) as high as 419.9mgg-1 and 408.8mgg-1 in single mode and binary mode based on Freudliuch isotherm model while those for BPA by PPAC-MS were 168.4mgg-1 and 254.7mgg-1 for single mode and binary modes corresponding to Langmuir isotherm model. Experiment results also indicated that the synergistic removal of BPA occurred because the precipitation process of Pb(II) leads to the co-precipitation of BPA with Pb(OH)2 compound. PPAC-MS showed a good reusability for 5 regeneration cycles using Mg(II) solution followed by thermal treatment. Overall, PPAC-MS has a high potential in the treatment process for wastewater containing both toxic heavy metals and emerging pollutants due to its high sorption capacities and reusability.

Matched MeSH terms: Magnesium Silicates/chemistry*
Carboxymethyl fenugreek galactomannan-gellan gum-calcium silicate composite beads for glimepiride delivery

Bera H, Mothe S, Maiti S, Vanga S

Int J Biol Macromol, 2018 Feb;107(Pt A):604-614.
PMID: 28916379 DOI: 10.1016/j.ijbiomac.2017.09.027

Novel carboxymethyl fenugreek galactomannan (CFG)-gellan gum (GG)-calcium silicate (CS) composite beads were developed for controlled glimepiride (GLI) delivery. CFG having degree of carboxymethylation of 0.71 was synthesized and characterized by FTIR, DSC and XRD analyses. Subsequently, GLI-loaded hybrids were accomplished by ionotropic gelation technique employing Ca+2/Zn+2/Al+3 ions as cross-linkers. All the formulations demonstrated excellent drug encapsulation efficiency (DEE, 48-97%) and sustained drug release behaviour (Q8h, 62-94%). These quality attributes were remarkably influenced by polymer-blend (GG:CFG) ratios, cross-linker types and CS inclusion. The drug release profile of the optimized formulation (F-6) was best fitted in zero-order model with anomalous diffusion driven mechanism. It also conferred excellent ex vivo mucoadhesive property and considerable hypoglycemic effect in streptozotocin-induced diabetic rats. Furthermore, the beads were characterized for drug-excipients compatibility, drug crystallinity, thermal behaviour and surface morphology. Thus, the developed hybrid matrices are appropriate for controlled delivery of GLI for Type 2 diabetes management.

Matched MeSH terms: Silicates/chemistry
Fulltext Effect of alumina and halloysite clay on electrical tree growth in silicone rubber nanocomposite

M. Hafiz, C.M.Salmi, M.Kamarol, M.Mariatti

Journal of Engineering and Science Research, 2018;2(3):20-25.
MyJurnal

Nowadays Silicone Rubber (SiR) is recommended in high voltage cable accessories fabrication as it offers excellent electrical and mechanical properties. Electrical tree is one of the phenomenon which contributes to the main factor of SiR insulation breakdown. Recently, a new approach has been applied in order to enhance the insulation strength properties by introducing nano filler in undoped material. Thus, this paper presents the influence of nano-alumina and halloysite nanoclay on electrical tree growth in SiR at 0, 1 vol%, 2 vol% and 3 vol% concentration. The electrical tree growth was investigated at 8kVrms after tree inception voltage (TIV) within 30 minutes under room temperature. The results show reductions of electrical tree growth speed and accumulate damage (%) up to 2 vol% nano-alumina and up to 3 vol% halloysite nanoclay. Nevertheless the presence of 3 vol% nano-alumina in SiR leads to the faster electrical tree growth rate and the worst accumulate damage within 1 minute of electrical tree growth process.

Matched MeSH terms: Aluminum Silicates
Fulltext Influence of alkylphosphonium modified montmorillonite to the tensile properties of PMMA composites

Abdullah, M.A.A., Mamat, M., Rusli, S.A., Kassim, A.A.

ASM Science Journal, 2018;11(101):96-104.
MyJurnal

Considering its excellent thermal stability, alkyl phosphonium surfactant: triisobutyl(methyl)phosphonium
(TIBMP) was used in this research as an intercalant for surface
modification of Na+-MMT via ion exchange process forming organomontmorillonite
(OMMT). The OMMT was then used as filler in poly(methyl methacrylate) (PMMA) via
melt intercalation technique. OMMT decomposed at a higher temperature than commercial
alkyammonium modified MMT. Exfoliated and intercalated types of nanocomposites
are obtained from PMMA/OMMTs at low and high content of OMMT loading, depending
on the space of those clay platelets had to disperse in PMMA. The ability of OMMT to
carry a certain load applied in PMMA matrix enhances the tensile strength in all composites.
TIBMP are compatible with PMMA matrix, and significantly improves the tensile
properties of PMMA composites.

Matched MeSH terms: Aluminum Silicates
Fulltext Assessment of radon emanation rate from various building materials in Malaysia using tight chamber method

Siti Fatimah Saipuddin, Ahmad Saat

Science Letters, 2018;12(2):11-18.
MyJurnal

Radon gas has been known as one of the main factors that cause breathing complications which lead to lung cancer, second only after smoking habit. As one of the most commonly found Naturally Occurring Radioactive Materials (NORM), its contribution to background radiation is immense, and its contributors, Uranium and Thorium are widely available on Earth and have been in existence for such a long time with long half-lives. Indoor radon exposure contributed by building materials worsens the effects. The probability of inhaling radon-polluted air and being surrounded by it in any buildings is very high. This research is focused on the detection of radon emanation rate from various building materials which are commonly being used in Malaysia. Throughout this research, common building materials used in constructions in Malaysia were collected and indoor radon exposure from each material was measured individually using Tight Chamber Method coupled to a Continuous Radon Monitor, CRM 1029. It has been shown that sand brick is the biggest contributor to indoor radon compared to other samples such as sand, soil, black cement, white cement, and clay brick. From the results, materials which have high radon emanation could be reconsidered as building materials and mitigation action can be chosen, suitable to its application.

Matched MeSH terms: Aluminum Silicates
Effects of nano-carbon reinforcement on the swelling and shrinkage behaviour of soil

Jamal M. A. Alsharef, Mohd Raihan Taha, Ramez A. Al-Mansob, Tanveer Ahmed Khan, Mohd Raihan Taha

Sains Malaysiana, 2018;47:195-205.

In this study, the performance of two types of nanocarbons (NCs), namely carbon nanotubes (CNTs) and carbon nanofibers (CNFs), on the three-dimensional shrinkage and swelling properties of three clayey soils were investigated. The specimens of soil mixed with clay with bentonite contents of 0, 10 and 20% by weight of dry soil. NC contents of 0.05, 0.075, 0.10 and 0.20% were chosen to investigate the influence of different NC types, CNTs and CNFs. All soil specimens were compacted under maximum dry unit weight and optimum water content conditions by using standard compaction tests. The physical and mechanical characteristics of the reinforced samples were then determined. These included the desiccation cracking area, used to determine the crack intensity factor (CIF), as well as the shrinkage and swelling. The CIF for the soil specimens without NCs were higher than the soil specimens with NC additives. These results show that NCs decrease the development of desiccation cracks on the surface of compacted samples. The shrinkage and swelling tests showed that the rate of volume changing of the compacted soil specimens reduced with the increasing of NCs.

Matched MeSH terms: Aluminum Silicates
Boron application in clay-loam soil for improved growth, yield and protein contents of mungbean in water-stresses

Rizwan Maqbool, Waqar Ali, Muhammad Ather Nadeem, Tasawer Abbas

Sains Malaysiana, 2018;47:51-58.

Boron is considered important to improve the drought resistance, yield and protein contents of pulses. Two years of field experiment was conducted to evaluate the effect of boron application and water stress given at vegetative and flowering stages on growth, yield and protein contents of mungbean during spring 2014 and 2015. The experiment was laid out in randomized complete block design with split-plot arrangement giving more emphasis to boron. The experiment comprised three water stress levels (normal irrigation, water stress at vegetative stage and water stress at reproductive phase) and four boron levels (0, 2, 4 and 6 kg ha-1). Final seed yield was significantly increased by different levels of boron application both under normal and water stressed conditions. The increase in yield was mainly due to greater plant height, number of pods bearing branches, number of pods per plant, number of seeds per pod and 1000-grain weight. Boron application at 4 kg ha-1 caused 17%, 10% and 4% increase in grain yield under normal irrigation, stress at vegetative stage and water stress at reproductive phase, respectively. Protein contents were also increased (9-16%) at same boron treatment. Most parameters showed a marked decrease at higher dose (6 kg ha-1) of boron. In conclusion, the boron application at rate of 4 kg ha-1 in clay-loam soil performed the best to enhance mungbean growth, yield and seed protein both under normal and water stressed conditions.

Matched MeSH terms: Aluminum Silicates

Filters

Please provide feedback to Administrator (afdal@afpm.org.my)

External Links