Biodiesel commercialization is questionable due to poor brake thermal efficiency. Biodiesel utilization should be improved with the addition of fuel additives. Hydrogen peroxide is a potential fuel additive due to extra hydrogen and oxygen content, which improves the combustion process. In this experimental study, biodiesel has been produced from Jatropha oil employing catalyzed transesterification homogeneously to examine its influence on the performance and emissions at engine loads with 1500 rpm utilizing a four-stroke single-cylinder diesel engine. D60B40 (having 60% diesel and 40% biodiesel) and D60B30A10 (60% diesel, 30% biodiesel and 10% hydrogen peroxide (H2O2)), are the fuel mixtures in the current study. The addition of H2O2 reduces emissions and enhances the combustion process. This effect occurred due to the micro-explosion of the injected fuel particles (which increases in-cylinder pressure and heat release rate (HRR)). An increase of 20% in BTE and 25% reduction in BSFC for D60B30A10 was observed compared to D60B40. Significant reduction in emissions of HC up to 17.54%, smoke by 24.6% CO2 by 3.53%, and an increase in NOx was noticed when the engine is operated with D60B30A10. The HRR increased up to 18.6%, ID reduced by 10.82%, and in-cylinder pressure increased by 8.5%. Test runs can be minimized as per Taguchi's design of experiments. It is possible to provide the estimates for the full factorial design of experiments. Exhaust gas temperature standards are evaluated and examined for all fuel blends.
To suffice the escalating global energy demand, microalgae are deemed as high potential surrogate feedstocks for liquid fuels. The major encumbrance for the commercialization of microalgae cultivation is due to the high costs of nutrients such as carbon, phosphorous, and nitrogen. Meanwhile, the organic-rich anaerobic digestate which is difficult to be purified by conventional techniques is appropriate to be used as a low-cost nutrient source for the economic viability and sustainability of microalgae production. This option is also beneficial in terms of reutilize the organic fraction of solid waste instead of discarded as zero-value waste. Anaerobic digestate is the side product of biogas production during anaerobic digestion process, where optimum nutrients are needed to satisfy the physiological needs to grow microalgae. Besides, the turbidity, competing biological contaminants, ammonia and metal toxicity of the digestate are also potentially contributing to the inhibition of microalgae growth. Thus, this review is aimed to explicate the feasibility of utilizing the anaerobic digestate to cultivate microalgae by evaluating their potential challenges and solutions. The proposed potential solutions (digestate dilution and pre-treatment, microalgae strain selection, extra organics addition, nitrification and desulfurization) corresponding to the state-of-the-art challenges are applicable as future directions of the research.
Depletion of non-renewable feedstock and severe wastewater pollution due to human activities have created negative impact to living organisms. The potential solution is to implement wastewater treatment and bioelectricity production through algae-based microbial fuel cell. The algae biomass produced from microbial fuel cell could be further processed to generate biofuels through their unique compositions. The consumption of nutrients in wastewater through algae cultivation and biomass produced to be utilized for energy supply have showed the potential of algae to solve the issues faced nowadays. This review introduces the background of algae and mitigation of wastewater using algae as well as the bioenergy status in Malaysia. The mechanisms of nutrient assimilation such as nitrogen, phosphorus, carbon, and heavy metals are included, followed by the application of algae in microbial fuel cell's chambers. Lastly, the status of algae for bioenergy production are covered.
The efforts have been made to review phyllosilicate derived (clay-based) heterogeneous catalysts for biodiesel production via lignocellulose derived feedstocks. These catalysts have many practical and potential applications in green catalysis. Phyllosilicate derived heterogeneous catalysts (modified via any of these approaches like acid activated clays, ion exchanged clays and layered double hydroxides) exhibits excellent catalytic activity for producing cost effective and high yield biodiesel. The combination of different protocols (intercalated catalysts, ion exchanged catalysts, acidic activated clay catalysts, clay-supported catalysts, composites and hybrids, pillared interlayer clay catalysts, and hierarchically structured catalysts) was implemented so as to achieve the synergetic effects (acidic-basic) in resultant material (catalyst) for efficient conversion of lignocellulose derived feedstock (non-edible oils) to biodiesel. Utilisation of these Phyllosilicate derived catalysts will pave path for future researchers to investigate the cost-effective, accessible and improved approaches in synthesising novel catalysts that could be used for converting lignocellulosic biomass to eco-friendly biodiesel.
Nowadays, the replacement of petro-diesel with biodiesel has raised the concern among the community for the utilization of improper feedstocks and the cost involved. However, these issues can be solved by producing single cell oil (SCO) from lignocellulosic biomass hydrolysates by oleaginous microorganisms. This study introduced Yarrowia lipolytica JCM 2320 with a desiccated coconut residue (DCR) hydrolysate (obtained from the 2% dilute sulphuric acid pretreatment) as a carbon source in generating SCO. However, common inhibitors formed during acid pretreatment of biomass such as five-hydroxymethylfurfural (HMF), furfural, acetic acid and levulinic acid resulting from the sugar degradations may have detrimental effects towards the fermentation process. To visualize the effect of inhibitors on Y. lipolytica, an inhibitory study was conducted by adding 0.5-5.0 g/L of potential inhibitors to the YPD (yeast, peptone and D-glucose) medium. It was found that the presence of furfural at 0.5 g/L would increase the lag phase, which beyond that was detrimental to Y. lipolytica. Furthermore, increasing the five-hydroxymethylfurfural (HMF) concentration would increase the lag phase of Y. lipolytica, whereas, for acetic acid and levulinic acid, it showed a negligible effect. Detoxification was hence conducted to remove the potential inhibitors from the DCR hydrolysate prior its utilization in the fermentation. To examine the possibility of using adsorption resins for the detoxification of DCR hydrolysate, five different resins were tested (Amberlite® XAD-4, Amberlite® XAD-7, Amberlite® IR 120, Amberlite® IRA 96 and Amberlite® IRA 402) with five different concentrations of 1%, 3%, 5%, 10% and 15% (w/v), respectively. At resin concentration of 10%, Amberlite® XAD-4 recorded the highest SCO yield, 2.90 ± 0.02 g/L, whereas the control and the conventional overliming detoxification method, recorded only 1.29 ± 0.01 g/L and 1.27 ± 0.02 g/L SCO accumulation, respectively. Moreover, the fatty acid profile of the oil produced was rich in oleic acid (33.60%), linoleic acid (9.90%), and palmitic acid (14.90%), which indicates the potential as a good biodiesel raw material.
Large-scale national and transnational commercial land transactions, or Large-Scale Land Acquisitions (LSLAs), have been gaining a lot of academic attention since the late 2000s and since the reported rush for land, resulting in turn from an increase in demand for arable land. If many data exist to characterize land deals, the analysis of investment networks remain limited and predominantly portrays power asymmetries between countries from the Global North investing in the Global South. The aim of this work is to perform a deeper investigation on the land trade market, specifically focusing on cases that do not follow such narratives. For instance, almost 25% of the countries included in the transnational land trade network do not follow a strict investor/target dichotomy, thus being characterized by a double role, i.e., they both acquire and cede land in the transnational context. In order to globally acknowledge for what was currently considered as abnormal cases, we model open access data about LSLAs extracted from the Land Matrix Initiative (LMI) open-access database into a network graph, and adapt an eigenvector based centrality method originally conceived for online social networks, namely LurkerRank, to identify and rank anomalous profiles in the land trade market. We take into account three different network snapshots: a multi-sector network (including all the transnational deals in the LMI database), and three networks referring to specific investment sectors (agriculture,mines and biofuels). Experimental results show that emerging economies (e.g., China and Malaysia) play a central role in the land trade market, by creating alternative dynamics that escape the classic North/South one. Our analyses also show how African countries that are often seen as targets of land trade transactions in a specific sector, may often acquire foreign land in the context of investments in the same sector (i.e., Zimbabwe for biofuels and the Democratic Republic of Congo for the mining sector).
Genetic engineering applications in the field of biofuel are rapidly expanding due to their potential to boost biomass productivity while lowering its cost and enhancing its quality. Recently, fourth-generation biofuel (FGB), which is biofuel obtained from genetically modified (GM) algae biomass, has gained considerable attention from academic and industrial communities. However, replacing fossil resources with FGB is still beset with many challenges. Most notably, technical aspects of genetic modification operations need to be more fully articulated and elaborated. However, relatively little attention has been paid to GM algal biomass. There is a limited number of reviews on the progress and challenges faced in the algal genetics of FGB. Therefore, the present review aims to fill this gap in the literature by recapitulating the findings of recent studies and achievements on safe and efficient genetic manipulation in the production of FGB. Then, the essential issues and parameters related to genome editing in algal strains are highlighted. Finally, the main challenges to FGB pertaining to the diffusion risk and regulatory frameworks are addressed. This review concluded that the technical and biosafety aspects of FGB, as well as the complexity and diversity of the related regulations, legitimacy concerns, and health and environmental risks, are among the most important challenges that require a strong commitment at the national/international levels to reach a global consensus.
Biodiesel, as a renewable and eco-friendly energy source that can be produced through algae oil esterification, has recently received much attention. Maximization of algal biomass and lipid content is crucial for commercial biodiesel production. In this study, Chlorella sp. PG96, a microalgal strain isolated from urban wastewater, was identified considering its morphological and molecular characteristics. Fractional factorial design (211-7) was employed to screen medium and environmental factors for achieving high lipid productivity. The effects of eleven factors including light intensity, light spectrum, aeration rate, temperature, salinity, NaHCO3, CO2, NaNO3, NH4Cl, MgSO4.7H2O, and K2HPO4 and their interactions on growth characteristics of Chlorella sp. PG96 (biomass and lipid production) were statistically assessed. Based on the experimental results, lipid productivity was at its maximum (54.19 ± 8.40 mglipid L-1 day-1) under a combination of high levels of all factors. The analysis also showed that physical parameters of light intensity and temperature were more effective on algal growth compared to nutritional parameters. Furthermore, nitrogen source of ammonium and carbon source of bicarbonate played more significant roles in biomass and lipid production, compared with nitrate and CO2, respectively. Although the effect of sulfur limitation on cellular growth was similar to phosphorus deficiency, S-limitation had a greater impact on lipid accumulation. The interaction between NaHCO3 and NH4Cl was the most prominent interaction affecting all responses. It is concluded that Chlorella sp. PG96 at a high level of light intensity and temperature (22500 Lux and 32 °C, respectively) can be a prospective candidate for biodiesel production.
Mariculture wastewater has drawn growing attention due to associated threats for coastal environment. However, most biological techniques exhibit unfavorable performance due to saline inhibition. Furthermore, only NaCl was used in most studies causing clumsy evaluation, undermining the potential of microalgal mariculture wastewater treatment. Herein, various concentrations of NaCl and sea salt are comprehensively examined and compared for their efficiencies of mariculture wastewater treatment and biodiesel conversion. The results indicate sea salt is a better trigger for treating wastewater (nearly 100% total nitrogen and total phosphorus removal) and producing high-quality biodiesel (330 mg/L•d). Structure equation model (SEM) further demonstrates the correlation of wastewater treatment performance and microalgal status is gradually weakened with increment of sea salt concentrations. Furthermore, metabolic analysis reveals enhanced photosynthesis might be the pivotal motivator for preferable outcomes under sea salt stimulation. This study provides new insights into microalgae-based approach integrating mariculture wastewater treatment and biodiesel production.
A key objective of renewable energy development in the USA is to reduce CO2 emissions by decreasing reliance on fossil fuels in the coming decades. Using quantile-on-quantile regressions, this research examines the relationship between disaggregated sources of renewable energy (biomass, biofuel, geothermal, hydroelectric, solar, wind, wood, and waste) and CO2 emissions in the USA during the period from 1995 to 2017. Our findings support the deployment of various types of renewables in combating CO2 emissions for each quantile. In particular, a negative effect of renewable energy consumption on CO2 emissions is observed for the lower quantiles in almost all types of renewables. The effect of all the renewable energy sources taken together is significant for the lower and upper quantiles of the provisional distribution of CO2 emissions. The effect of renewable energy becomes stronger and more significant in the middle quantiles, where a pronounced causal effect of return and volatility is detected for the lower and upper middle quantiles. At the same time, heterogeneity in the findings across various types of renewable energy sources reveals differences in the relative importance of each type within the energy sector taken as a whole. Future US initiatives in renewable energy deployment at both the federal and the state levels should take into consideration the relative importance of each type, so as to maximize the efficacy of renewable energy policies in combating CO2 emissions.
A diesel engine running on diesel/biodiesel mixtures containing ethylene glycol diacetate (EGDA) was investigated from the exergoeconomic and exergoenvironmental viewpoints. Biodiesel was mixed with petrodiesel at 5% and 20% volume ratios, and the resultant mixtures were then doped with EGDA at 1-3% volume ratios. The exergetic sustainability indicators of the engine operating on the prepared fuel formulations were determined at varying engine loads. The indicators were selected to support decision-making on fuel composition and engine load following thermodynamic, economic, and environmental considerations. The engine load markedly affected all the studied exergetic parameters. The highest engine exergetic efficiency (39.5%) was obtained for petrodiesel doped with 1 v/v% EGDA at the engine load of 50%. The minimum value of the unit cost of brake power exergy (49.6 US$/GJ) was found for straight petrodiesel at full-load conditions, while the minimum value of the unit environmental impact of brake power exergy (29.9 mPts/GJ) was observed for petrodiesel mixed with 5 v/v% biodiesel at the engine load of 75%. Overall, adding EGDA to fuel mixtures did not favorably influence the outcomes of both exergetic methods due to its energy-intensive and cost-prohibitive production process. In conclusion, although petrodiesel fuel improvers such EGDA used in the present study could properly mitigate pollutant emissions, the adverse effects of such additives on thermodynamic parameters of diesel engines, particularly on exergoeconomic and exergoenvironmental indices, need to be taken into account, and necessary optimizations should be made before their real-world application.
Biomass co-firing with coal can be adopted in the electricity sector to promote greenhouse gas reduction, renewable energy production, and resource efficiency improvement toward environmental sustainability. This realization, however, requires effective management of supply chain issues, such as the collection of biomass feedstock, the transportation of biomass, and the localization of biomass processing plants to deliver the co-firing scales needed. This work addresses these issues by providing a techno-economic assessment conducted in a spatially-explicit manner to investigate the opportunity for scaling up the co-firing deployment at the national scale. The modeling approach is applied to the case of Malaysia's coal and palm oil biomass industries. The number of cases involving the impact of energy decarbonization targets, economic policy instrument, and supply chain cost parameter variations on the co-firing scales deployed are assessed. The findings show that densified biomass feedstock can substitute significant shares of coal capacities to deliver up to 29 MtCO2/year of carbon dioxide reduction. Nevertheless, this would cause a surge in the electricity system cost by up to 2 billion USD/year due to the substitution of up to 40% of the coal plant capacities. In facilitating the maximal deployment of co-firing at the national scale, more than 100 solid biofuel production plants would need to be built to support a maximum of 41 TWh/year of co-firing capacity. Actions to minimize the specific cost elements of the biomass co-firing supply chain are thus needed in the near term to increase the effectiveness of economic policy instrument to promote co-firing and reduce environmental emissions.
The increase in global population size over the past 100 decades has doubled the requirements for energy resources. To mitigate the limited fossil fuel available, new clean energy sources being environmental sustainable for replacement of traditional energy sources are explored to supplement the current scarcity. Biomass containing lignin and cellulose is the main raw material to replace fossil energy given its abundance and lower emission of greenhouse gases and NOx when transformed into energy. Bacteria, fungi and algae decompose lignocellulose leading to generation of hydrogen, methane, bioethanol and biodiesel being the clean energy used for heating, power generation and the automobile industry. Microbial Fuel Cell (MFC) uses microorganisms to decompose biomass in wastewater to generate electricity and remove heavy metals in wastewater. Biomass contains cellulose, hemicellulose, lignin and other biomacromolecules which need hydrolyzation for conversion into small molecules by corresponding enzymes in order to be utilized by microorganisms. This paper discusses microbial decomposition of biomass into clean energy and the five major ways of clean energy production, and its economic benefits for future renewable energy security.
Microalgae have drawn significant interest worldwide, owing to their enormous application potential in the green energy, biopharmaceutical, and nutraceutical industries. Many studies have proved and stated the potential of microalgae in the area of biofuel which is economically effective and environmentally friendly. Besides the commercial value, the potential of microalgae in environmental protection has also been investigated. Microalgae-based process is one of the most effective way to treat heavy metal pollution, compared to conventional methods, it does not release any toxic waste or harmful gases, and the aquatic organism will not receive any harmful effects. The potential dual role of microalge in phytoremedation and energy production has made it widely explored for its capability. The interest of microalgae in various application has motivated a new focus in green technologies. Considering the rapid population growth with the continuous increase on the global demand and the application of biomass in diverse field, significant upgrades have been performed to accommodate green technological advancement. In the past decade, noteworthy advancement has been made on the technology involving the diverse application of microalgae biomass. This review aims to explore on the application of microalgae and the development of green technology in various application for microalgae biomass. There is great prospects for researchers in this field to delve into other potential utilization of microalgae biomass not only for bioremediation process but also to generate revenues from microalgae by incorporating clean and green technology for long-term sustainability and environmental benefits.
Microalgae are a promising feedstock for carbon-neutral biofuel production due to their superior cellular composition. Alternatively, oxidative torrefaction has been recognized as a potential thermochemical technique for microalgal solid biofuel upgrading. Herein, by using microalga N. oceanica as a feedstock, several characterizations are adopted for evaluating the potential of oxidative torrefaction towards microalgal solid biofuel production. The oxidatively torrefied microalgae can be upgraded as lignite. After in-depth analysis, significant change in the surface microstructure of oxidatively torrefied microalgae is largely changed (via wrinkle and fragmentation) The hydrophobicity, thermal decomposition, thermal stability, and aromatization of oxidatively torrefied microalgae can be largely enhanced as the oxidative torrefaction severity increase. With the increasing torrefaction temperature, the hydrophobicity of oxidative torrefied microalgae gradually improved. The decomposition of C-2/3/5, and -OCH3, the CO bonds of CH3CO-, and the aromatization occurs via oxidative torrefaction according to the NMR analysis. For XPS analysis, torrefaction operation significantly decreases the carbide carbon and enhances the graphitization. As a result, the thermal stability of oxidatively torrefied microalgae is improved. Conclusively, the information obtained in this study can provide insights into the evaluation of oxidative torrefaction performance and fuel properties of microalgal solid biofuel, which may help accelerate the advancement of oxidative torrefaction industrialization.
The rapid thermal cracking technology of biomass can convert biomass into bio-oil and is beneficial for industrial applications. Agricultural and forestry wastes are important parts of China's energy, and their high-grade utilization is useful to solve the problem of energy shortages and environmental pollution. To the best of our knowledge, the impact of nanocatalysts on converting biowastes for bio-oil has not been studied. Consequently, we examined the production of bio-oil by pyrolysis of Aesculus chinensis Bunge Seed (ACBS) using nanocatalysts (Fe2O3 and NiO catalysts) for the first time. The pyrolysis products of ACBS include 1-hydroxy-2-propanone (3.97%), acetic acid (5.42%), and furfural (0.66%). These chemical components can be recovered for use as chemical feedstock in the form of bio-oil, thus indicating the potential of ACBS as a feedstock to be converted by pyrolysis to produce value-added bio-oil. The Fe2O3 and NiO catalysts enhanced the pyrolysis process, which accelerated the precipitation of gaseous products. The pyrolysis rates of the samples gradually increased at DTGmax, effectively promoting the catalytic cracking of ACBS, which is beneficial to the development and utilization of ACBS to produce high valorization products. Combining ACBS and nanocatalysts can change the development direction of high valorization agricultural and forestry wastes in the future.
Microalgae are potential sustainable renewable sources of energy but are highly underutilized due to the expensive and time-consuming downstream processing. This study aims at curbing these obstacles by extracting multiple components with a single processing unit. In this work, an ultrasound-assisted liquid triphasic flotation system was incorporated to extract proteins, lipids, and carbohydrates by phase separation. The parameters involved were optimized and the final recovery efficiency of proteins, lipids, and carbohydrates was determined. A control run involving conventional three-phase partitioning and a 15-fold scale-up system with the recycling of phase components were also performed. Gas Chromatograph and Fourier Transform Infrared spectroscopy were used to examine the potential of extracted products as a source of biofuel. This biorefinery approach is crucial in commercializing microalgae for biodiesel and bioethanol generation with a side product of purified proteins as feed.
Over the past decades, research efforts are being devoted into utilizing the biomass waste as a major source of green energy to maintain the economic, environmental, and social sustainability. Specifically, there is an emerging consensus on the significance of glycerol (an underutilised waste from biodiesel industry) as a cheap, non-toxic, and renewable source for valuable chemicals synthesis. There are numerous methods enacted to convert this glycerol waste to tartronic acid, mesoxalic acid, glyceraldehyde, dihydroxyacetone, oxalic acid and so on. Among these, the green electro-oxidation technique is one of the techniques that possesses potential for industrial application due to advantages such as non-toxicity process, fast response, and lower energy consumption. The current review covers the general understanding on commonly used techniques for alcohol (C1 & C2) conversion, with a specific insight on glycerol (C3) electro-oxidation (GOR). Since catalysts are the backbone of chemical reaction, they are responsible for the overall economy prospect of any processes. To this end, a comprehensive review on catalysts, which include noble metals, non-noble metals, and non-metals anchored over various supports are incorporated in this review. Moreover, a fundamental insight into the development of future electrocatalysts for glycerol oxidation along with products analysis is also presented.
Sustainable aviation fuels (SAFs) are expected to play an essential role in achieving the aviation industries' goal of carbon-neutral growth. However, producing biomass-based SAFs may induce changes in global land use and the associated carbon stock. The induced land use change (ILUC) emissions, as a part of the full life-cycle emissions for SAF pathways, will affect whether and to what extent SAFs reduce emissions compared with petroleum-based jet fuels. Here, we estimate the ILUC emission intensity for seventeen SAF pathways considered by the International Civil Aviation Organization (ICAO), covering five ASTM-certified technologies, nine biomass-based feedstocks, and four geographical regions. We introduce the SAF pathways into a well-established computable general equilibrium (CGE) model, GTAP-BIO, and its coupled emission accounting model, AEZ-EF, to study economy-wide implications of SAF production and estimate ILUC emissions intensity for each pathway. The estimated SAF ILUC emission intensities, using a 25-year amortization period, range from -58.5 g CO2e MJ-1 for the USA miscanthus alcohol (isobutanol)-to-jet (ATJ) pathway to 34.6 g CO2e MJ-1 for the Malaysia & Indonesia palm oil Hydrotreated Esters of Fatty Acids (HEFA) pathway. Notably, the vegetable oil pathways tend to have higher ILUC emission intensities due to their linkage to palm expansion and peatland oxidation in Southeast Asia. The cellulosic pathways studied provide negative ILUC emissions, mainly driven by the high carbon sequestrations in crop biomass and soil. Using the core life-cycle emissions established by ICAO, we show that fifteen of the assessed pathways have a lower full life-cycle emission intensity than petroleum-based jet fuels (89 g CO2e MJ-1), offering promising options to reduce aviation emissions.
Waste management in Malaysia remains a persistent economic and environmental challenge. Up to date, more than 80% of Malaysian solid waste disposed at landfills and dumpsites. Therefore, Malaysia is facing an urgent need to move towards a sustainable solid waste management and thus resource recovery from organic solid waste. Hence, this study aims to investigate the feasibility of energy and bio fertilizer recovery from organic fraction municipal solid waste (OFMSW) via anaerobic digestion. The economic and environmental benefit analysis was investigated. Approximate and elementary analysis of OFMSW samples were carried out to estimate the potential production of biogas and bio fertilizer. It was found that organic waste contributes about 45% of the total MSW generated in Malaysia. Anaerobic digestion of 50% of organic waste is expected to produce 3941 MWh/day of electrical energy and 2500 t/day of bio fertilizer. In terms of environmental impacts, 2735 t/day of Carbon dioxide (CO2) emission, 1128 m2/day of landfilling area and 481 m3/day of leachate can be avoided. A net revenue of 3300 million RM (1 US Dollar ≈ 4.15 RM) can be generated by the sales of electricity via Feed-in-Tariff (FiT), sales of biofertilizer to local agricultural industries and inclusive of the saving generated from the reduction of OFMSW landfilling operations and leachate treatment at landfills. Economic development can go hand-in-hand with environmental sound practices in the field of waste management.