Ni-doped cobalt aluminate NixCo1-xAl2O4 (x = 0.0, 0.2, 0.4, 0.6, 0.8 and 1.0) spinel nanoparticles were successfully synthesized by a simple microwave combustion method using urea as the fuel and as well as reducing agent. X-ray powder diffraction (XRD) was confirmed the formation of single phase, cubic spinel cobalt-nickel aluminate structure without any other impurities. Average crystallite sizes of the samples were found to be in the range of 18.93 nm to 21.47 nm by Scherrer's formula. Fourier transform infrared (FT-IR) spectral analysis was confirmed the corresponding functional groups of the M-O, Al-O and M-Al-O (M = Co and Ni) bonds of spinel NixCo1-xAl2O4 structure. Scanning electron microscope (SEM) and transmission electron microscope (TEM) images was confirmed the particle like nanostructured morphology. Energy band gap (Eg) value was calculated using UV-Visible diffuse reflectance spectra (DRS) and the Eg values increased with increasing Ni2+ dopant from x = 0.2 (3.58 eV) to x = 1.0 (4.15 eV). Vibrating sample magnetometer (VSM) measurements exposed that undoped and Ni-doped CoAl2O4 samples have superparamagnetic behavior and the magnetization (Ms) values were increased with increasing Ni2+ ions. Spinel NixCo1-xAl2O4 samples has been used for the catalytic oxidation of benzyl alcohol into benzaldehyde and was found that the sample Ni0.6Co0.4Al2O4 showed higher conversion 94.37% with 100% selectivity than other samples, which may be due to the smaller particle size and higher surface area.
Three cases of occupational exposure to radio-frequency and microwave radiation were seen at the out-patient clinic, Hospital Universiti Sains Malaysia. They presented with run-down symptoms of neck strain associated with throbbing headache, irritability, loss of appetite, fatigue, memory difficulties, and numbness of extremities. They also presented with alopecia areata which is felt to be causally linked to the radiation exposure.
Study site: Outpatient clinic Hospital Universiti Sains Malaysia (HUSM)
A new, effective one-pot synthesis of the 6, N2-diaryl-1,3,5-triazine-2,4-diamines under microwave irradiation was developed. The method involved an initial three-component condensation of cyanoguanidine, aromatic aldehydes, and arylamines in the presence of hydrochloric acid. Without isolation, the resulting 1,6-diaryl-1,6-dihydro-1,3,5-triazine-2,4-diamines were treated with a base to initiate Dimroth rearrangement and spontaneous dehydrogenative aromatization, affording the desired compounds. The developed method was found to be sufficiently general in scope, tolerating various aromatic aldehydes and amines; by using their combinations in the first step, a representative library of 110 compounds was successfully prepared and screened for anticancer properties.
Nanocrystalline aluminosilicate F-type zeolite (K-F, EDI-type structure) was synthesized in an organic template-free system
using rice husk ash (RHA) silica source and microwave energy. The morphology, crystallite size, chemical composition,
crystallographic and basicity properties of the nanocrystals were studied by using various characterization techniques.
The results showed that fully crystalline K-F zeolite (Si/Al ratio = 1.26) with flattened cuboid-like shaped could be
obtained within 2 min of crystallization which was considerably very fast. In addition, K-F zeolite nanocrystals was also
tested as a solid base catalyst in the microwave-enhanced Aldol condensation reaction of heptanal with benzaldehyde
and the six catalytic parameters were studied and optimized. The nanosized K-F zeolite crystals showed good catalytic
performance in the studied reaction with 77.1% heptanal conversion and 69.5% jasminaldehyde selectivity under optimum
reaction condition. The nanocatalyst was reusable and no significant loss in its catalytic reactivity was observed even
after five consecutive reaction cycles.
Nanocrystalline lead sulfide (PbS) thin films have been successfully grown on glass substrate using the chemical bath deposition technique. Microwave oven was used as a heating source to facilitate the growth process of the thin films. Aqueous solutions of lead nitrate Pb(NO3) and thiourea [SC(NH2)2] were used as lead and sulfur ion sources, respectively. Structural, morphological and optical analyses revealed good quality growth of nanocrystalline PbS thin films. This study introduced a facile and low cost method to prepare high quality nanocrystalline PbS thin films in a relatively short growth time for optoelectronic applications.
The Coronavirus Disease 2019 (COVID-19) pandemic has induced a critical supply of personal protective equipment (PPE) especially N95 respirators. Utilizing respirator decontamination procedures to reduce the pathogen load of a contaminated N95 respirator can be a viable solution for reuse purposes. In this study, the efficiency of a novel hybrid respirator decontamination method of ultraviolet germicidal irradiation (UVGI) which utilizes ultraviolet-C (UV-C) rays coupled with microwave-generated steam (MGS) against feline coronavirus (FCoV) was evaluated. The contaminated 3M 1860 respirator pieces were treated with three treatments (UVGI-only, MGS-only, and Hybrid-UVGI + MGS) with variable time. The virucidal activity was evaluated using the TCID50 method. The comparison of decontamination efficiency of the treatments indicated that the hybrid method achieved at least a pathogen log reduction of 4 logs, faster than MGS and UVGI. These data recommend that the proposed hybrid decontamination system is more effective comparatively in achieving pathogen log reduction of 4 logs.
Nitrogen doped titanium dioxide (N-doped TiO2
) was synthesized by microwave using urea as nitrogen sources with
commercially available TiO2
-P25. The N-doped TiO2
was compared with unmodified TiO2
by carrying out the investigation
on its properties using x-ray diffraction (XRD) analysis, Brunauer-Emmett-Teller (BET), Fourier transformed infrared
spectroscopy (FTIR) and diffuse reflectance spectroscopy (UV-Vis DRS). The photocatalytic activities of N-doped TiO2
and unmodified TiO2 were studied for photodegradation of reactive red 4 (RR4) under light emitting diode (LED) light
irradiation. An active photoresponse under LED light irradiation was observed from N-doped TiO2
with 60 min of time
irradiation to complete RR4 color removal while no photocatalytic degradation was observed from unmodified.
The study examined the protein profile of Pectoralis major muscle in broiler chickens subjected to different freezing and thawing methods. Pectoralis major muscle was excised from the carcasses of twenty broiler chickens and split into left and right halves. The left half was subjected to slow freezing (-20oC) while the right half was rapidly frozen (-80oC). The samples were stored at their respective temperature for 2 weeks and assigned to either of tap water (27oC, 30 min), room temperature (26oC, 60 min), microwave (750W, 10 min) or chiller (4oC, 6 h) thawing. Changes in myofibrillar proteins following the thawing methods were monitored through sodium dodecyl sulfate polyacrylamide gel electrophoresis (SDS-PAGE). The electrophoretic profile indicated differences (p < 0.05) in intensities of the components of myofibrillar proteins among the thawing methods in both slow and rapidly frozen samples. Chiller thawing had significantly higher (p < 0.05) protein concentration than other methods in rapidly frozen samples. However, in slow freezing, there were no significant differences in protein concentration among the thawing methods. In rapidly frozen samples, the protein optical densities at molecular weight of 21, 27, 55 and 151kDa in tap water, chiller and room temperature thawing did not differ (p < 0.05). Similarly, in slowly frozen samples, protein optical densities at molecular weight of 21, 27, 85 and 151 kDa were not significantly different among chill, tap water and room temperature thawing. Microwave thawing consistently caused higher protein degradation resulting in significantly lower (p < 0.05) protein quality and quantity in both freezing methods.
Recently, TiO2/multi-walled carbon nanotube (MWCNT) hybrid nanocatalysts have been a subject of high interest due to their excellent structures, large surface areas and peculiar optical properties, which enhance their photocatalytic performance. In this work, a modified microwave technique was used to rapidly synthesise a TiO2/MWCNT nanocatalyst with a large surface area. X-ray powder diffraction, field-emission scanning electron microscopy, transmission electron microscopy and Brunauer-Emmett-Teller measurements were used to characterise the structure, morphology and the surface area of the sample. The photocatalytic activity of the hybrid nanocatalysts was evaluated through a comparison of the degradation of methylene blue dye under irradiation with ultraviolet and visible light. The results showed that the TiO2/MWCNT hybrid nanocatalysts degraded 34.9% of the methylene blue (MB) under irradiation with ultraviolet light, whereas 96.3% of the MB was degraded under irradiation with visible light.
A modeling technique based on absorbed microwave energy was proposed to model microwave-assisted extraction (MAE) of antioxidant compounds from cocoa (Theobroma cacao L.) leaves. By adapting suitable extraction model at the basis of microwave energy absorbed during extraction, the model can be developed to predict extraction profile of MAE at various microwave irradiation power (100-600 W) and solvent loading (100-300 ml). Verification with experimental data confirmed that the prediction was accurate in capturing the extraction profile of MAE (R-square value greater than 0.87). Besides, the predicted yields from the model showed good agreement with the experimental results with less than 10% deviation observed. Furthermore, suitable extraction times to ensure high extraction yield at various MAE conditions can be estimated based on absorbed microwave energy. The estimation is feasible as more than 85% of active compounds can be extracted when compared with the conventional extraction technique.
Burn wound management is a complex process because the damage may extend as far as the dermis which has an acknowledged slow rate of regeneration. This study investigates the feasibility of using hydrogel microparticles composed of bacterial cellulose and polyacrylamide as a dressing material for coverage of partial-thickness burn wounds. The microparticulate carrier structure and surface morphology were investigated by Fourier transform infrared, X-ray diffraction, elemental analysis, and scanning electron microscopy. The cytotoxicity profile of the microparticles showed cytocompatibility with L929 cells. Dermal irritation test demonstrated that the hydrogel was non-irritant to the skin and had a significant effect on wound contraction compared to the untreated group. Moreover, histological examination of in vivo burn healing samples revealed that the hydrogel treatment enhanced epithelialization and accelerated fibroblast proliferation with wound repair and intact skin achieved by the end of the study. Both the in vitro and in vivo results proved the biocompatibility and efficacy of hydrogel microparticles as a wound dressing material.
Although microwave irradiation has been used in the histopathology laboratory for several years, there has been minimal published experimental data on its effects on the technical and staining quality of histological sections. Furthermore, it has not been clear whether the advantages gained in reduction of fixation and staining duration has been at the expense of increasing architectural distortion to the tissues. We report here our experience with computerised morphometric analysis to investigate glomerular artifacts caused by microwave-stimulated fixation of renal tissues. 39 rat and 33 human autopsy kidney samples were subjected to (1) fixation in neutral buffered formaldehyde (control), (2) microwave-stimulated fixation followed by neutral buffered formaldehyde, and (3) neutral buffered formaldehyde followed by microwave irradiation. In addition, the effect of post-fixation in 70% ethanol was also investigated. Microwave irradiation was delivered through a dedicated laboratory microwave oven at 80% power and at 55 degrees C for 3 minutes. The different fixation methods were compared with regards to shrinkage (distortion) to glomerular structures (glomeruli and Bowman's spaces) on H and E sections, as determined by morphometric image analysis using a temporary assembled-system consisting of a trinocular microscope, a digital video camera and personal computer. A FlashPoint VGA 3.3 film-grabber card was used to capture images for morphometric analysis by using a Scion Image program. Morphometric analysis of glomerular structures showed that microwaves caused more shrinkage to the area bounded by the Bowman's capsule than the glomerulus proper, but post-fixation with ethanol reduced this shrinkage. These findings have implications on the logistics of tissue preparation of renal biopsies in clinical practice.
We investigated microwave-stimulated fixation of tissues for transmission electron microscopy using a domestic microwave oven operating at a frequency of 2.45 GHz with an output power of 500W. Microwave-stimulated fixation, in 4% glutaraldehyde, of fresh rat kidney, liver, heart and brain tissues was compared to conventional fixation. Human renal biopsies were similarly studied. Electron microscopy showed excellent ultrastructural preservation comparable to that obtained by conventional fixation. The optimal temperature range for microwave-stimulated fixation was found to lie between 50 degrees C and 55 degrees C. Our results indicate that microwave-stimulated fixation is a rapid and reproducible technique and can be effectively applied to routine diagnostic pathology.
This work is aimed to determine the characteristics of activated carbons derived from palm kernel shell (PKS) by microwave-induced zinc chloride activation for dye removal. Activation was performed in a microwave oven at power intensity of 70% for 10 min. The same procedures were repeated for activation using recycled ZnCl2 solution from the first activation. The activated carbons were characterized according to surface area, morphology, functional groups and batch adsorption. The yield for the first activation was 70.7% with surface area of 858m2/g. It was found that the activated carbon prepared using the recycled ZnCl2 still possesses good surface area for methylene blue removal. The adsorption behaviour of the continuous system was well fitted to and could be satisfactorily described by the Yoon and Nelson model.
CO2 gasification of oil palm shell (OPS) char to produce CO through the Boudouard reaction (C + CO2 ↔ 2CO) was investigated under microwave irradiation. A microwave heating system was developed to carry out the CO2 gasification in a packed bed of OPS char. The influence of char particle size, temperature and gas flow rate on CO2 conversion and CO evolution was considered. It was attempted to improve the reactivity of OPS char in gasification reaction through incorporation of Fe catalyst into the char skeleton. Very promising results were achieved in our experiments, where a CO2 conversion of 99% could be maintained during 60 min microwave-induced gasification of iron-catalyzed char. When similar gasification experiments were performed in conventional electric furnace, the superior performance of microwave over thermal driven reaction was elucidated. The activation energies of 36.0, 74.2 and 247.2 kJ/mol were obtained for catalytic and non-catalytic microwave and thermal heating, respectively.
The increasing demand for high-performance lithium-ion batteries (LIBs) has emphasized the need for affordable and sustainable materials, prompting the exploration of waste upcycling to address global sustainability challenges. In this study, we efficiently converted polypropylene (PP) plastic waste from used centrifuge tubes into activated polypropylene carbon (APC) using microwave-assisted pyrolysis. The synthesis of APC was optimized using response surface methodology/central composite design (RSM/CCD). Based on the RSM results, the optimal conditions for PP plastic conversion into carbon were determined as follows: HNO3 concentration of 3.5 M, microwave temperature of 230 °C, and holding time of 25 min. Under these conditions, the obtained intensity ratio of Id/Ig in PP carbon was 0.681 ± 0.013, with an error of 6.81 ± 0.013 % between predicted and actual values. The physicochemical studies, including FESEM-EDX, XRD, and Raman spectroscopy, confirmed the successful synthesis of APC samples. The APC 800 material exhibited a well-organized three-dimensional structure characterized by large pores and mesopores, enabling fast ion transport in the electrode. As a result, the APC 800 electrode demonstrated an initial discharge capacity of 381.0 mAh/g, an improved initial coulombic efficiency of 85.1%, and excellent cycling stability after 100 cycles. Notably, the APC 800 electrode displayed remarkable rate performance, showing a reversible capacity of 355.1 mAh/g when the current density was reset to 0.2 A/g, highlighting its high electrochemical reversibility. The outstanding characteristics of APC 800 as an anode electrode material for high-performance lithium-ion batteries suggest a promising future for its application in the field.
A new series of N-sec/tert-butyl 2-arylbenzimidazole derivatives was synthesised in 85-96% yields within 2-3.5 min by condensing ethyl 3-amino-4-butylamino benzoate with various substituted metabisulfite adducts of benzaldehyde under focused microwave irradiation. The benzimidazole analogues were characterised using (1)H NMR, (13)C NMR, high resolution MS and melting points. Evaluation of antiproliferative activity of the benzimidazole analogues against MCF-7 and MDA-MB-231 revealed several compounds with unexpected selective inhibitions of MDA-MB-231 in micromolar range. All analogues were found inactive towards MCF-7. The most potent inhibition against MDA-MB-231 human breast cancer cell line came from the unsubstituted 2-phenylbenzimidazole 10a.
Nanocomposites of Zn/Al-layered double hydroxide(anthraquinone-2,6-disulfonate) were synthesized by spontaneous direct assembly of inorganic and organic phases from aqueous solution. Powder X-ray diffraction patterns showed that a pure, single nanocomposite phase of good crystallinity was obtained using 1.0 M antraquinone-2,6-disulfonate ion (AQ26) and aging at 80 degrees C using conventional heating for 7 days or 0.5 h under microwave radiation, and these samples are denoted as ZAAN26C or ZAAN26MH, respectively. Zn/Al-nitrate-layered double hydroxide synthesized by a conventional method (ZANLC) showed a basal spacing of 8.3 A while both the nanocomposites showed 18.8 A as a result of AQ26 intercalation. FTIR study showed that the resulting nanocomposites are free from nitrate, the co-anion present in the mother liquor, indicating that only AQ26 is preferred during intercalation for the formation of the nanocomposite. The Brunauer, Emmet and Teller (BET) and micropore surface areas for ZAAN26C decreased relative to the ZANLC from 16.2 to 4.7 and 1.6 to 1.3 m2/g, respectively. These results indicate that AQ26 can be rapidly interdcalated in layered double hydroxide using microwave-aging resulting in a nanocomposite.
Microwave heating was used in the regeneration of methylene blue-loaded activated carbons produced from fibers (PFAC), empty fruit bunches (EFBAC) and shell (PSAC) of oil palm. The dye-loaded carbons were treated in a modified conventional microwave oven operated at 2450 MHz and irradiation time of 2, 3 and 5 min. The virgin properties of the origin and regenerated activated carbons were characterized by pore structural analysis and nitrogen adsorption isotherm. The surface chemistry was examined by zeta potential measurement and determination of surface acidity/basicity, while the adsorptive property was quantified using methylene blue (MB). Microwave irradiation preserved the pore structure, original active sites and adsorption capacity of the regenerated activated carbons. The carbon yield and the monolayer adsorption capacities for MB were maintained at 68.35-82.84% and 154.65-195.22 mg/g, even after five adsorption-regeneration cycles. The findings revealed the potential of microwave heating for regeneration of spent activated carbons.