Displaying publications 81 - 100 of 340 in total

Abstract:
Sort:
  1. Sharip NS, Ariffin H, Yasim-Anuar TAT, Andou Y, Shirosaki Y, Jawaid M, et al.
    Polymers (Basel), 2021 Jan 27;13(3).
    PMID: 33513876 DOI: 10.3390/polym13030404
    The major hurdle in melt-processing of ultra-high molecular weight polyethylene (UHMWPE) nanocomposite lies on the high melt viscosity of the UHMWPE, which may contribute to poor dispersion and distribution of the nanofiller. In this study, UHMWPE/cellulose nanofiber (UHMWPE/CNF) bionanocomposites were prepared by two different blending methods: (i) melt blending at 150 °C in a triple screw kneading extruder, and (ii) non-melt blending by ethanol mixing at room temperature. Results showed that melt-processing of UHMWPE without CNF (MB-UHMWPE/0) exhibited an increment in yield strength and Young's modulus by 15% and 25%, respectively, compared to the Neat-UHMWPE. Tensile strength was however reduced by almost half. Ethanol mixed sample without CNF (EM-UHMWPE/0) on the other hand showed slight decrement in all mechanical properties tested. At 0.5% CNF inclusion, the mechanical properties of melt-blended bionanocomposites (MB-UHMWPE/0.5) were improved as compared to Neat-UHMWPE. It was also found that the yield strength, elongation at break, Young's modulus, toughness and crystallinity of MB-UHMWPE/0.5 were higher by 28%, 61%, 47%, 45% and 11%, respectively, as compared to the ethanol mixing sample (EM-UHMWPE/0.5). Despite the reduction in tensile strength of MB-UHMWPE/0.5, the value i.e., 28.4 ± 1.0 MPa surpassed the minimum requirement of standard specification for fabricated UHMWPE in surgical implant application. Overall, melt-blending processing is more suitable for the preparation of UHMWPE/CNF bionanocomposites as exhibited by their characteristics presented herein. A better mechanical interlocking between UHMWPE and CNF at high temperature mixing with kneading was evident through FE-SEM observation, explains the higher mechanical properties of MB-UHMWPE/0.5 as compared to EM-UHMWPE/0.5.
    Matched MeSH terms: Reference Standards
  2. Algamili AS, Khir MHM, Dennis JO, Ahmed AY, Alabsi SS, Ba Hashwan SS, et al.
    Nanoscale Res Lett, 2021 Jan 26;16(1):16.
    PMID: 33496852 DOI: 10.1186/s11671-021-03481-7
    Over the last couple of decades, the advancement in Microelectromechanical System (MEMS) devices is highly demanded for integrating the economically miniaturized sensors with fabricating technology. A sensor is a system that detects and responds to multiple physical inputs and converting them into analogue or digital forms. The sensor transforms these variations into a form which can be utilized as a marker to monitor the device variable. MEMS exhibits excellent feasibility in miniaturization sensors due to its small dimension, low power consumption, superior performance, and, batch-fabrication. This article presents the recent developments in standard actuation and sensing mechanisms that can serve MEMS-based devices, which is expected to revolutionize almost many product categories in the current era. The featured principles of actuating, sensing mechanisms and real-life applications have also been discussed. Proper understanding of the actuating and sensing mechanisms for the MEMS-based devices can play a vital role in effective selection for novel and complex application design.
    Matched MeSH terms: Reference Standards
  3. Harun MS, Wong TW, Fong CW
    Int J Pharm, 2021 Jan 25;593:120099.
    PMID: 33259902 DOI: 10.1016/j.ijpharm.2020.120099
    This study investigated combination nanocarrier and microwave system for α-tocopherol and γ-tocotrienol delivery against dermatitis, without skin thinning effect of steroids. The vitamin E was formulated into water-rich/water-poor nanoemulsions, and had their droplet size, zeta potential, morphology, therapeutic content, encapsulation efficiency and release, in vitro skin therapeutics/nanoemulsion penetration, retention and permeation profiles, and in vivo pharmacodynamics characteristics examined, with skin pre-treated by precision microwave when applicable. The nanoemulsions had droplet sizes <150 nm and negative zeta potential values. The skin pre-treatment by microwave (1 mW/3985 MHz) promoted therapeutics accumulation in epidermis through enhancing nanoemulsion penetration into skin. The combination nano- and microwave technologies fluidized skin lipid and protein domains with epidermal microstructures being fluidized to a greater extent than dermis, allowing a relatively high epidermal-to-dermal nanoemulsion distribution. Microwave of lower or higher than 3985 MHz brought about lower skin therapeutics/nanoemulsion accumulation due to insufficient lipid/protein domain fluidization or microwave-skin interaction limiting at skin surfaces only. Using water-rich nanoemulsion with higher therapeutic release and skin pre-treatment with 3985 MHz microwave, dermatitis was alleviated in vivo without skin thinning of standard steroid. The use of combination microwave and nanotechnology promotes vitamin delivery and translates to positive dermatitis treatment outcome that warrants future investigation.
    Matched MeSH terms: Reference Standards
  4. Lim SM, Choo JM, Li H, O'Rielly R, Carragher J, Rogers GB, et al.
    Foods, 2021 Jan 21;10(2).
    PMID: 33494480 DOI: 10.3390/foods10020220
    High amylose wheat (HAW) contains more resistant starch than standard amylose wheat (SAW) and may have beneficial effects on gastrointestinal health. However, it is currently unclear whether these effects differ according to the level of HAW included in the diet or between males and females. Male and female C57BL/6 mice (n = 8/group/sex) were fed SAW65 (65% SAW; control), HAW35 (35% HAW), HAW50 (50% HAW) or HAW65 (65% HAW) diet for eight weeks. Female but not male, mice consuming any amount of HAW exhibited accelerated gastric emptying compared to SAW65 group. In both sexes, relative colon weights were higher in the HAW65 group compared to SAW65 group and in females, relative weights of the small intestine and cecum were also higher in the HAW65 group. In females only, colonic expression of Pyy and Ocln mRNAs were higher in the HAW65 group compared to HAW35 and HAW50 groups. In both sexes, mice consuming higher amounts of HAW (HAW50 or HAW65) had increased fecal bacterial load and relative abundance of Bacteroidetes phylum and reduced relative abundance of Firmicutes compared to SAW65 group. These data are consistent with a beneficial impact of HAW on gastrointestinal health and indicate dose-dependent and sex-specific effects of HAW consumption.
    Matched MeSH terms: Reference Standards
  5. Kumari M, Tahlan S, Narasimhan B, Ramasamy K, Lim SM, Shah SAA, et al.
    BMC Chem, 2021 Jan 21;15(1):5.
    PMID: 33478538 DOI: 10.1186/s13065-020-00717-y
    BACKGROUND: Triazole is an important heterocyclic moiety that occupies a unique position in heterocyclic chemistry, due to its large number of biological activities. It exists in two isomeric forms i.e. 1,2,4-triazole and 1,2,3-triazole and is used as core molecule for the design and synthesis of many medicinal compounds. 1,2,4-Triazole possess broad spectrum of therapeutically interesting drug candidates such as analgesic, antiseptic, antimicrobial, antioxidant, anti-urease, anti-inflammatory, diuretics, anticancer, anticonvulsant, antidiabetic and antimigraine agents.

    METHODS: The structures of all synthesized compounds were characterized by physicochemical properties and spectral means (IR and NMR). The synthesized compounds were evaluated for their in vitro antimicrobial activity against Gram-positive (B. subtilis), Gram-negative (P. aeruginosa and E. coli) bacterial and fungal (C. albicans and A. niger) strains by tube dilution method using ciprofloxacin, amoxicillin and fluconazole as standards. In-vitro antioxidant and anti-urease screening was done by DPPH assay and indophenol method, respectively. The in-vitro anticancer evaluation was carried out against MCF-7 and HCT116 cancer cell lines using 5-FU as standards.

    RESULTS, DISCUSSION AND CONCLUSION: The biological screening results reveal that the compounds T5 (MICBS, EC = 24.7 µM, MICPA, CA = 12.3 µM) and T17 (MICAN = 27.1 µM) exhibited potent antimicrobial activity as comparable to standards ciprofloxacin, amoxicillin (MICCipro = 18.1 µM, MICAmo = 17.1 µM) and fluconazole (MICFlu = 20.4 µM), respectively. The antioxidant evaluation showed that compounds T2 (IC50 = 34.83 µg/ml) and T3 (IC50 = 34.38 µg/ml) showed significant antioxidant activity and comparable to ascorbic acid (IC50 = 35.44 µg/ml). Compounds T3 (IC50 = 54.01 µg/ml) was the most potent urease inhibitor amongst the synthesized compounds and compared to standard thiourea (IC50 = 54.25 µg/ml). The most potent anticancer activity was shown by compounds T2 (IC50 = 3.84 μM) and T7 (IC50 = 3.25 μM) against HCT116 cell lines as compared to standard 5-FU (IC50 = 25.36 μM).

    Matched MeSH terms: Reference Standards
  6. Baig MA, Swamy KB
    Indian J Pathol Microbiol, 2021 1 13;64(1):123-127.
    PMID: 33433421 DOI: 10.4103/IJPM.IJPM_900_19
    Background: In the laboratory, factor VIII can be measured by three different methodologies, such as one-stage clotting assay, two-stage clotting assay, and chromogenic assay. These assays differ in ease of use, variety of reagents available, sensitivity to mild hemophilia A, and interference from lupus anticoagulants (LACs). Certain factor VIII gene mutations can cause discrepancy in results between one-stage activated partial thromboplastin time (APTT) and chromogenic assays.

    Materials and Methods: The coagulometer for factor VIII assay is Sysmex CS-5100. All data were expressed as mean ± standard deviation (SD).

    Results: A total of 135 cases were studied. Of these, 100 cases were of mild hemophilia A diagnosed by molecular genetics and, 15 cases were positive for LAC, which were confirmed by dilute Russell Viper venom test. Clot-based one-stage APTT assay showed 65% sensitivity and 80% specificity in diagnosing mild hemophilia A cases and out of 15 LAC cases, it showed false positivity in five cases. Chromogenic assay showed 85% sensitivity and 90% specificity in diagnosing mild hemophilia cases and was 100% specific in excluding LAC cases.

    Conclusions: One-stage APTT assay is the most commonly used test for determining factor VIII levels but chromogenic assay are considered as the gold standard and recommended as the reference method by European Pharmacopoeia and ISTH subcommittee. Mild hemophilia A patients with missense mutations show discrepancy between the one-stage clot-based APTT assay and chromogenic assays for determination of factor VIII level and this can lead to misdiagnosis or misclassification of mild hemophilia A. Therefore, it is recommended that both the assays should be used in the evaluation of mild hemophilia cases.

    Matched MeSH terms: Reference Standards
  7. Paroha S, Verma J, Dubey RD, Dewangan RP, Molugulu N, Bapat RA, et al.
    Int J Pharm, 2021 Jan 05;592:120043.
    PMID: 33152476 DOI: 10.1016/j.ijpharm.2020.120043
    Cancer is a community health hazard which progress at a fatal rate in various countries across the globe. An agent used for chemotherapy should exhibit ideal properties to be an effective anticancer medicine. The chemotherapeutic medicines used for treatment of various cancers are, gemcitabine, paclitaxel, etoposide, methotrexate, cisplatin, doxorubicin and 5-fluorouracil. However, many of these agents present nonspecific systemic toxicity that prevents their treatment efficiency. Of all, gemcitabine has shown to be an active agent against colon, pancreatic, colon, ovarian, breast, head and neck and lung cancers in amalgamation with various anticancer agents. Gemcitabine is considered a gold-standard and the first FDA approved agent used as a monotherapy in management of advanced pancreatic cancers. However due to its poor pharmacokinetics, there is need of newer drug delivery system for efficient action. Nanotechnology has shown to be an emerging trend in field of medicine in providing novel modalities for cancer treatment. Various nanocarriers have the potential to deliver the drug at the desired site to obtain information about diagnosis and treatment of cancer. This review highlights on various nanocarriers like polymeric nanoparticles, solid lipid nanoparticles, mesoporous silica nanoparticles, magnetic nanoparticles, micelles, liposomes, dendrimers, gold nanoparticles and combination approaches for delivery of gemcitabine for cancer therapy. The co-encapsulation and concurrent delivery of Gem with other anticancer agents can enhance drug action at the cancer site with reduced side effects.
    Matched MeSH terms: Reference Standards
  8. Tey HY, See HH
    J Chromatogr A, 2021 Jan 04;1635:461731.
    PMID: 33285415 DOI: 10.1016/j.chroma.2020.461731
    Conventional sampling of biological fluids often involves a bulk quantity of samples that are tedious to collect, deliver and process. Miniaturized sampling approaches have emerged as promising tools for sample collection due to numerous advantages such as minute sample size, patient friendliness and ease of shipment. This article reviews the applications and advances of microsampling techniques in therapeutic drug monitoring (TDM), covering the period January 2015 - August 2020. As whole blood is the gold standard sampling matrix for TDM, this article comprehensively highlights the most historical microsampling technique, the dried blood spot (DBS), and its development. Advanced developments of DBS, ranging from various automation DBS, paper spray mass spectrometry (PS-MS), 3D dried blood spheroids and volumetric absorptive paper disc (VAPD) and mini-disc (VAPDmini) are discussed. The volumetric absorptive microsampling (VAMS) approach, which overcomes the hematocrit effect associated with the DBS sample, has been employed in recent TDM. The sample collection and sample preparation details in DBS and VAMS are outlined and summarized. This review also delineates the involvement of other biological fluids (plasma, urine, breast milk and saliva) and their miniaturized dried matrix forms in TDM. Specific features and challenges of each microsampling technique are identified and comparison studies are reviewed.
    Matched MeSH terms: Reference Standards
  9. Almoudi MMM, Hussein AS, Abu Hassan MI, Al-Talib H, Khan HBSG, Nazli SAB, et al.
    Eur Oral Res, 2021 Jan 04;55(1):8-15.
    PMID: 33937756 DOI: 10.26650/eor.20210119
    Purpose: This study aims to evaluate the antimicrobial effects of the cholecalciferol vitamin D3 against Streptococcus sobrinus (Strep. sobrinus) and Streptococcus mutans (Strep. mutans) bacteria in vitro that is considered the main causative bacteria in dental caries development.

    Materials and methods: The antimicrobial effects of vitamin D3 were evaluated against Strep. sobrinus and Strep mutans using the agar disc diffusion method. The minimum inhibitory concentration (MIC) and minimum bactericidal concentration (MBC) of vitamin D3 were determined using a microdilution method following the guidelines by the Clinical Laboratory Standards Institute (CLSI). Scanning electron microscope (SEM) was used to evaluate the morphological changes of bacterial cells following exposure to vitamin D3.

    Results: Strep. sobrinus was more sensitive to vitamin D3 compared to Strep. mutans bacteria. The MIC values of vitamin D3 against Strep. sobrinus and Strep. mutans were 60 μg/ mL and 250 μg/mL respectively whereas the MBC values were 120 μg/mL and 500 μg/mL, respectively. Moreover, significant changes in the bacterial morphology were observed in treated bacterial cells with vitamin D3 as compared to the untreated control bacteria using SEM.

    Conclusion: These findings suggested that vitamin D3 has excellent antimicrobial effects against Strep. sobrinus and Strep. mutans and may be considered as a promising compound in the prevention of dental caries in the future. Further research is recommended to elucidate the mechanism of vitamin D3 on these bacteria.

    Matched MeSH terms: Reference Standards
  10. Azhari NR, Yahaya N, Mohd Suah FBM, Prabu S, Yih Hui B, Shahriman MS, et al.
    Chirality, 2021 01;33(1):37-50.
    PMID: 33197086 DOI: 10.1002/chir.23285
    A chiral separation method coupled with capillary electrophoresis (CE) analysis for ketoconazole and miconazole enantiomers using chiral selectors such as β-cyclodextrin (β-CD) and hydroxypropyl-β-CD (HP-β-CD) was developed in this study, which included the optimisation, validation and application of the method on the antifungal cream samples. The formation of inclusion complex between the hosts (β-CD and HP-β-CD) and guests (ketoconazole and miconazole) were compared and analysed using ultraviolet-visible spectrophotometry, nuclear magnetic resonance (NMR) spectroscopy and molecular docking methods. Results from the study showed that in a concentration that ranged between 0.25 and 50 mg L-1 , the linear calibration curves of each enantiomer had a high coefficient of regression (R2 > 0.999), low limit of detection (0.075 mg L-1 ) and low limit of quantification (0.25 mg L-1 ). The relative standard deviation (RSD) of the intraday and interday analyses ranged from 0.79% to 8.01% and 3.30% to 11.43%, respectively, while the recoveries ranged from 82.0% to 105.7% (RSD < 7%, n = 3). The most probable structure of the inclusion complexes was proposed based on the findings from the molecular docking studies conducted using the PatchDock server.
    Matched MeSH terms: Reference Standards
  11. Patil PG, Seow LL, Uddanwadikar R, Ukey PD
    J Prosthet Dent, 2021 Jan;125(1):138.e1-138.e8.
    PMID: 33393474 DOI: 10.1016/j.prosdent.2020.09.015
    STATEMENT OF PROBLEM: Mini implants (<3 mm in diameter) are being used as an alternative to standard implants for implant-retained mandibular overdentures; however, they may exhibit higher stresses at the crestal level.

    PURPOSE: The purpose of this finite element analysis study was to evaluate the biomechanical behavior (stress distribution pattern) in the mandibular overdenture, mucosa, bone, and implants when retained with 2 standard implants or 2 mini implants under unilateral or bilateral loading conditions.

    MATERIAL AND METHODS: A patient with edentulous mandible and his denture was scanned with cone beam computed tomography (CBCT), and a 3D mandibular model was created in the Mimics software program by using the CBCT digital imaging and communications in medicine (DICOM) images. The model was transferred to the 3Matics software program to form a 2-mm-thick mucosal layer and to assemble the denture DICOM file. A 12-mm-long standard implant (Ø3.5 mm) and a mini dental implant (Ø2.5 mm) along with the LOCATOR male attachments (height 4 mm) were designed by using the SOLIDWORKS software program. Two standard or 2 mini implants in the canine region were embedded separately in the 3D assembled model. The base of the mandible was fixed, and vertical compressive loads of 100 N were applied unilaterally and bilaterally in the first molar region. The material properties for acrylic resin (denture), titanium (implants), mucosa (tissue), and bone (mandible) were allocated. Maximum von Mises stress and strain values were obtained and analyzed.

    RESULTS: Maximum stresses of 9.78 MPa (bilaterally) and 11.98 MPa (unilaterally) were observed in 2 mini implants as compared with 3.12 MPa (bilaterally) and 3.81 MPa (unilaterally) in 2 standard implants. The stress values in the mandible were observed to be almost double the mini implants as compared with the standard implants. The stresses in the denture were in the range of 3.21 MPa and 3.83 MPa and in the mucosa of 0.68 MPa and 0.7 MPa for 2 implants under unilateral and bilateral loading conditions. The strain values shown similar trends with both implant types under bilateral and unilateral loading.

    CONCLUSIONS: Two mini implants generated an average of 68.15% more stress than standard implants. The 2 standard implant-retained overdenture showed less stress concentration in and around implants than mini implant-retained overdentures.

    Matched MeSH terms: Reference Standards
  12. Jamal FN, Arafat Dzulkarnain AA, Shahrudin FA, Marzuki MN
    J Audiol Otol, 2021 Jan;25(1):14-21.
    PMID: 32575950 DOI: 10.7874/jao.2020.00073
    BACKGROUND AND OBJECTIVES: There is growing interest in the use of the Level-specific (LS) CE-Chirp® stimulus in auditory brainstem response (ABR) due to its ability to produce prominent ABR waves with robust amplitudes. There are no known studies that investigate the test-retest reliability of the ABR to the LS CE-Chirp® stimulus. The present study aims to investigate the test-retest reliability of the ABR to the LS CE-Chirp® stimulus and compare its reliability with the ABR to standard click stimulus at multiple intensity levels in normal-hearing adults.

    SUBJECTS AND METHODS: Eleven normal-hearing adults participated. The ABR test was repeated twice in the same clinical session and conducted again in another session. The ABR was acquired using both the click and LS CE-Chirp® stimuli at 4 presentation levels (80, 60, 40, and 20 dBnHL). Only the right ear was tested using the ipsilateral electrode montage. The reliability of the ABR findings (amplitudes and latencies) to the click and LS CE-Chirp® stimuli within the same clinical session and between the two clinical sessions was calculated using an intra-class correlation coefficient analysis (ICC).

    RESULTS: The results showed a significant correlation of the ABR findings (amplitude and latencies) to both stimuli within the same session and between the clinical sessions. The ICC values ranged from moderate to excellent.

    CONCLUSIONS: The ABR results from both the LS CE-Chirp® and click stimuli were consistent and reliable over the two clinical sessions suggesting that both stimuli can be used for neurological diagnoses with the same reliability.

    Matched MeSH terms: Reference Standards
  13. Awosolu OB, Yahaya ZS, Farah Haziqah MT, Simon-Oke IA, Fakunle C
    Heliyon, 2021 Jan;7(1):e05975.
    PMID: 33521357 DOI: 10.1016/j.heliyon.2021.e05975
    Background: Malaria is a severe global public health challenge that causes significant morbidity and mortality worldwide, particularly in sub-Saharan Africa. This study was designed to determine the prevalence, parasite density, and risk factors associated with malaria infection transmission among residents of two urban communities of Ibadan, southwestern Nigeria.

    Materials and methods: A cross-sectional hospital-based study was carried out on 300 participants. Blood samples were obtained. Thick and thin blood films were prepared and viewed using the standard parasitological technique of microscopy. Moreover, data on sociodemographic and environmental variables were obtained using a pre-tested standard questionnaire.

    Results: Of the 300 participants examined, a total of 165 (55.0%) were found positive for Plasmodium falciparum with a mean (S.D) parasite density of 1814.70 (1829.117) parasite/μL of blood. The prevalence and parasite density of malaria infection vary significantly (P < 0.05) with age group. Children <5 years old were more likely to have malaria infection and high parasite densities than adults (p < 0.05). Similarly, in relation to gender, males significantly (P < 0.05) had a higher prevalence (60.2%) and mean (S.D) parasite density of malaria infection [2157.73 (1659.570) parasite/μL of blood] compared to females. Additionally, those without formal education had the highest prevalence (73.0%) and mean (S.D) parasite density of infection [2626.96 (2442.195) parasite/μL of blood]. The bivariate logistic regression analysis shows that age group 6-10 (Crude Odds Ratio, COR 0.066, 95% CI: 0.007-0.635), presence of streams/rivers (COR 0.225, 95% CI: 0.103-0.492), distance from streams/rivers within ≤1 km (COR 0.283, 95% CI: 0.122-0.654) and travel to rural area (COR 4.689, 95% CI: 2.430-9.049) were the significant risk factors.

    Conclusions: Malaria infection is prevalent in the study area and was greatly influenced by traveling activities from the rural areas to urban centers and vice versa. Multifaceted and integrated control strategy should be adopted. Health education on mosquito prevention and chemoprophylaxis before and during travel to rural areas are essential.

    Matched MeSH terms: Reference Standards
  14. Razak KAA, Ghani KHA, Musa AA
    Injury, 2021 Jan;52(1):90-94.
    PMID: 33168201 DOI: 10.1016/j.injury.2020.11.004
    BACKGROUND: Acetabular fractures in childhood are rare and the literature is scarce to describe a standard protocol in surgical management of these injuries. As the patient is still growing, it warrants a detailed assessment with a sound surgical plan if operative intervention is deemed necessary to prevent late complications. Throughout literature, most fixation rely on using pins, screws, plates or combination of the three which require large surgical exposure and risk of secondary physeal injury, hence we come up with a method of using the Titanium Elastic Nail System (TENS) to overcome this issue. We describe a novel technique in managing acetabular fractures in this group of patients using the TENS.

    METHOD: An 8 year old girl with a diagnosis of right anterior column posterior hemitransverse acetabular fracture was fixed with 3 TENS for supra-acetabular, anterior column and posterior column fragments. Surgery was performed in a minimally invasive manner. No drilling was performed during the surgery and implant insertion is done manually.

    RESULTS: Advantages of this procedure include minimally invasive surgery with smaller wounds, minimal intraoperative bleeding and theoretically reduces the risk of premature fusion of the triradiate cartilage. Patient is allowed early rehabilitation with this method.

    CONCLUSION: This novel method provides an alternative to traditional usage of wires, pins, plates and screws as is described in most literature. However, it requires the surgeon to appreciate that the safe corridors for the implant are much narrower than adults. We recommend this technique for fractures that are deemed suitable for intramedullary fixation and further research in the future will be needed.

    Matched MeSH terms: Reference Standards
  15. Sang C, Yan H, Chan WK, Zhu X, Sun T, Chang X, et al.
    Front Med (Lausanne), 2021;8:637652.
    PMID: 33708783 DOI: 10.3389/fmed.2021.637652
    Non-alcoholic fatty liver disease (NAFLD) is one of the main causes of fibrosis. Liver biopsy remains the gold standard for the confirmation of fibrosis in NAFLD patients. Effective and non-invasive diagnosis of advanced fibrosis is essential to disease surveillance and treatment decisions. Herein we used routine medical test markers and logistic regression to differentiate early and advanced fibrosis in NAFLD patients from China, Malaysia, and India (n1 = 540, n2 = 147, and n3 = 97) who were confirmed by liver biopsy. Nine parameters, including age, body mass index, fasting blood glucose, presence of diabetes or impaired fasting glycemia, alanine aminotransferase, γ-glutamyl transferase, triglyceride, and aspartate transaminase/platelet count ratio, were selected by stepwise logistic regression, receiver operating characteristic curve (ROC), and hypothesis testing and were used for model construction. The area under the ROC curve (auROC) of the model was 0.82 for differentiating early and advanced fibrosis (sensitivity = 0.69, when specificity = 0.80) in the discovery set. Its diagnostic ability remained good in the two independent validation sets (auROC = 0.89 and 0.71) and was consistently superior to existing panels such as the FIB-4 and NAFLD fibrosis score. A web-based tool, LiveFbr, was developed for fast access to our model. The new model may serve as an attractive tool for fibrosis classification in NAFLD patients.
    Matched MeSH terms: Reference Standards
  16. Abidin NZ, Mitra SR
    Curr Gerontol Geriatr Res, 2021;2021:6634474.
    PMID: 33790963 DOI: 10.1155/2021/6634474
    Osteosarcopenic obesity (OSO) describes the concurrent presence of obesity, low bone mass, and low muscle mass in an individual. Currently, no established criteria exist to diagnose OSO. We hypothesized that obese individuals require different cut-points from standard cut-points to define low bone mass and low muscle mass due to their higher weight load. In this study, we determined cutoff values for the screening of osteosarcopenia (OS) in obese postmenopausal Malaysian women based on the measurements of quantitative ultrasound (QUS), bioelectrical impedance analysis (BIA), and functional performance test. Then, we compared the cutoff values derived by 3 different statistical modeling methods, (1) receiver operating characteristic (ROC) curve, (2) lowest quintile of the study population, and (3) 2 standard deviations (SD) below the mean value of a young reference group, and discussed the most suitable method to screen for the presence of OS in obese population. One hundred and forty-one (n = 141) postmenopausal Malaysian women participated in the study. Bone density was assessed using calcaneal quantitative ultrasound. Body composition was assessed using bioelectrical impedance analyzer. Handgrip strength was assessed using a handgrip dynamometer, and physical performance was assessed using a modified Short Physical Performance Battery test. ROC curve was determined to be the most suitable statistical modeling method to derive the cutoffs for the presence of OS in obese population. From the ROC curve method, the final model to estimate the probability of OS in obese postmenopausal women is comprised of five variables: handgrip strength (HGS, with area under the curve (AUC) = 0.698 and threshold ≤ 16.5 kg), skeletal muscle mass index (SMMI, AUC = 0.966 and threshold ≤ 8.2 kg/m2), fat-free mass index (FFMI, AUC = 0.946 and threshold ≤ 15.2 kg/m2), broadband ultrasonic attenuation (BUA, AUC = 0.987 and threshold ≤ 52.85 dB/MHz), and speed of sound (SOS, AUC = 0.991 and threshold ≤ 1492.15 m/s). Portable equipment may be used to screen for OS in obese women. Early identification of OS can help lower the risk of advanced functional impairment that can lead to physical disability in obese postmenopausal women.
    Matched MeSH terms: Reference Standards
  17. Mohd Khairuddin I, Sidek SN, P P Abdul Majeed A, Mohd Razman MA, Ahmad Puzi A, Md Yusof H
    PeerJ Comput Sci, 2021;7:e379.
    PMID: 33817026 DOI: 10.7717/peerj-cs.379
    Electromyography (EMG) signal is one of the extensively utilised biological signals for predicting human motor intention, which is an essential element in human-robot collaboration platforms. Studies on motion intention prediction from EMG signals have often been concentrated on either classification and regression models of muscle activity. In this study, we leverage the information from the EMG signals, to detect the subject's intentions in generating motion commands for a robot-assisted upper limb rehabilitation platform. The EMG signals are recorded from ten healthy subjects' biceps muscle, and the movements of the upper limb evaluated are voluntary elbow flexion and extension along the sagittal plane. The signals are filtered through a fifth-order Butterworth filter. A number of features were extracted from the filtered signals namely waveform length (WL), mean absolute value (MAV), root mean square (RMS), standard deviation (SD), minimum (MIN) and maximum (MAX). Several different classifiers viz. Linear Discriminant Analysis (LDA), Logistic Regression (LR), Decision Tree (DT), Support Vector Machine (SVM) and k-Nearest Neighbour (k-NN) were investigated on its efficacy to accurately classify the pre-intention and intention classes based on the significant features identified (MIN and MAX) via Extremely Randomised Tree feature selection technique. It was observed from the present investigation that the DT classifier yielded an excellent classification with a classification accuracy of 100%, 99% and 99% on training, testing and validation dataset, respectively based on the identified features. The findings of the present investigation are non-trivial towards facilitating the rehabilitation phase of patients based on their actual capability and hence, would eventually yield a more active participation from them.
    Matched MeSH terms: Reference Standards
  18. Md. Shamsur Rahman, David Matanjun, Urban John Arnold D’souza, Wan Salman Wan Saudi, Fairrul Kadir, Tan, Teck Song, et al.
    MyJurnal
    Irrational use of drugs could be detrimental issues in the practices of healthcare communities. This problem arises either because of the wrong prescription or inappropriate self-medication. Faulty prescribing practices and incorrect self-medication will lead to an ineffective treatment regime. Still, they can also be unsafe as these may exacerbate or prolong the illness and distress the patients. In turn, these will incur unnecessary treatment costs. The most typical issues in the irrational use of drugs are the patient’s lack of information about the medicine and inadequate proper consultation from physicians. Lack of regulation in the appropriate use and supply of drugs by the relevant enforcement agencies could also be the problem in the irrational use of drugs. Ulceration and inflammation due to the irrational use of NSAIDs, antibiotics, and unhealthy lifestyle may contribute to the novel therapeutic strategy challenges. The ability to purchase the drugs without a doctor’s prescription of nonsteroidal anti-inflammatory drugs (NSAIDs) was also the landmark event that became the most widely used medications for the anti-inflammatory, analgesic, and antipyretic effects. Inadequate knowledge from both drug providers and patients may contribute to the most recognized influential factors in the irrational use of drugs in various countries. The recommendation should introduce an appropriate educational intervention that can be designed to promote rational prescribing. Proper regulation on prescription practices by policymakers and physicians could be the way to ensure the standard of rational usage of drugs have compliant with the healthcare communities.
    Matched MeSH terms: Reference Standards
  19. Yeo BH, Tang TK, Wong SF, Tan CP, Wang Y, Cheong LZ, et al.
    Front Pharmacol, 2021;12:631136.
    PMID: 33833681 DOI: 10.3389/fphar.2021.631136
    Edible bird's nest (EBN) is recognized as a nourishing food among Chinese people. The efficacy of EBN was stated in the records of traditional Chinese medicine and its activities have been reported in many researches. Malaysia is the second largest exporter of EBNs in the world, after Indonesia. For many years, EBN trade to China was not regulated until August 2011, when a safety alert was triggered for the consumption of EBNs. China banned the import of EBNs from Malaysia and Indonesia due to high level of nitrite. Since then, the Malaysia government has formulated Malaysia Standards for swiftlet farming (MS 2273:2012), edible bird's nest processing plant design and management (MS 2333:2010), and edible bird's nest product quality (MS 2334:2011) to enable the industry to meet the specified standards for the export to China. On the other hand, Indonesia's EBN industry formulated a standard operating procedure (SOP) for exportation to China. Both countries can export EBNs to China by complying with the standards and SOPs. EBN contaminants may include but not limited to nitrite, heavy metals, excessive minerals, fungi, bacteria, and mites. The possible source of contaminants may come from the swiftlet farms and the swiftlets or introduced during processing, storage, and transportation of EBNs, or adulterants. Swiftlet house design and management, and EBN processing affect the bird's nest color. Degradation of its optical quality has an impact on the selling price, and color changes are tied together with nitrite level. In this review, the current and future prospects of EBNs in Malaysia and Indonesia in terms of their quality, and the research on the contaminants and their effects on EBN color changes are discussed.
    Matched MeSH terms: Reference Standards
  20. Che Mohd Hilmi Che Mat1, Zulkiflee Salahuddin, Nik Azrizie Muhamed, Irfan Mohamad
    MyJurnal
    Osteomas occur in all parts of the temporal bone, including the mastoid, squamous, middle
    ear, styloid process, internal auditory canal and external auditory canal (EAC). The EAC has
    been reported to be the most common site, followed by the mastoid and squamous parts.
    Diagnosis is made based on history, clinical examination and radiological findings. Computed
    tomography reveals a pedunculated hyperdense mass that usually arises from the
    tympanosquamous suture. Surgical removal of EAC osteomas can be achieved using the
    endaural or postauricular approaches. It can be performed with a drill or osteotome, either
    endoscopically or by using microscopy. This report presents two patients with EAC osteomas
    who underwent excision under microscopy using the endaural approach. Surgery is the gold
    standard treatment, while close observation may be considered in asymptomatic patients.
    Matched MeSH terms: Reference Standards
Filters
Contact Us

Please provide feedback to Administrator (afdal@afpm.org.my)

External Links