MyMedR

Displaying publications 81 - 100 of 142 in total

Abstract:

Sort:

Fulltext Preparation and characterization of glass-ceramic synthesized from soda lime glass and wastewater sludge

Zaidan Abdul Wahab, Syaharudin Zaibon, Khamirul Amin Matori, Norfarezah Hanim Edros, Thai, Ming Yeow, Mohd Zul Hilmi Mayzan, et al.

Pertanika Journal of Science & Technology, 2010;18(2):-.
MyJurnal

This paper reports an alternative method for making glass-ceramic from disposal waste water
sludge and soda lime silica (SLS) glass. The glass ceramic samples were prepared from a mixture
of wastewater sludge and SLS glasses, melted at 1375°C for 3 hours and quenched by pouring into
water to obtain a coarse frit. The frit glass was then crushed and sieved to 106μm before it was
pressed to a pellet. The sintering process was performed at various temperatures between 700-
1000°C for 2 hours and morphologically characterized with XRD, SEM, and EDX. Overall results
showed the crystalline phase of diopside sodian-critobalite glass-ceramic is depending on thermal
treatment process and making them attractive to industrial uses such as in construction, tiling, and
glass-ceramic applications.

Matched MeSH terms: Ceramics
Fulltext Heat treatment effect with the electrode contact of CaCu3Ti4O12

Muhammad Azwadi Sulaiman, Hutagalung, Sabar D., Zainal A. Ahmad

Journal of Nuclear and Related Technologies, 2013;2013(2):43-52.
MyJurnal

CaCu3Ti4O12 (CCTO) has attracted a great attention for electronic devices miniaturization due to its
very high dielectric constant properties at a wide range of frequency and nearly constant over broad temperature range. The origins of the giant dielectric constant have been speculated from electrical heterogeneous of interior elements of the CCTO ceramics. Four origins were suggested contributed to the electrical heterogeneous. In this study heat treatment were done with the electrode contact in Argon gas environment and the electrical properties over very wide frequency of CCTO ceramics were investigated. Cylindrical CCTO pellets samples were prepared by solid state reaction method and single phase of XRD pattern was obtained after sintering processes. Electrical impedance responds were measured at frequency from 100 Hz to 1 GHz for the samples for untreated and heat treated at 200ºC, 250ºC, 300ºC, 350ºC and 400ºC of CCTO. Improvement to the dielectric constant can be seen for 350ºC and 400ºC samples and dielectric loss were improved for 200ºC and 300ºC samples for overall frequency. The variations were discussed based on oxygen deficiency content and resistivity of the elements inside of CCTO structure.

Matched MeSH terms: Ceramics
Fulltext Recovery of uranium from Malaysian non-conventional sources

Meor Yusoff, M.S.

Journal of Nuclear and Related Technologies, 2010;2010(2):55-65.
MyJurnal

The recovery of uranium from non-conventional sources has its importance in the security of nuclear fuel supply as well as producing a more value-added product to the contaminated source. In this paper, uranium is recovered both by developing a hydrothermal process as well as using the removal method. Developing hydrothermal process involves using high uranium concentrated starting material such as xenotime and thorium hydroxide waste produced from the monazite cracking process. Oxalate separation enable to produce a better uranium and thorium separation from the yttrium in xenotime as compared to the hydroxide precipitation. Also, a solvent extraction stage was included to separate the uranium from the thorium in the process using thorium hydroxide waste. The removal method involves using selective leaching for minerals with lower uranium content such as zircon. A better removal for uranium and thorium in zircon is achieved when a heat treatment process was done prior to the leaching stage. White zircon mineral was produced after this treatment and its quality meets the requirement for white ceramic opacifier and glaze.

Matched MeSH terms: Ceramics
Fulltext Study on radon emanation from selected building materials in Malaysia

Ahmed, Al-Halemi, Jaafar, M.S.

Journal of Nuclear and Related Technologies, 2010;2010(1):14-20.
MyJurnal

Radon-222 emanation from selected locally produced samples of building materials, used in Malaysia were measured using the Professional Continuous Radon Monitor Model 1027, which is a patented electronic detecting-junction photodiode sensor to measure the concentration of radon gas. Each sample was placed for 72 hours inside a 3.11 x 10 -2 m 3 sealed container. It was found that the average radon concentration Bqm -3 of air for concrete bricks, concrete brick with cemented coatings, concrete brick with cemented coatings and paint samples were, 303.7 Bq/m 3, 436.6 Bqm -3, and 410.7 Bqm -3, respectively. (Bqm -3 ) for brown clay brick, brown clay brick with cemented coatings, brown clay brick with cemented coatings and paint were 166.5 Bqm -3, 166.5 Bqm -3, and 148 Bqm -3, respectively. (Bqm -3 ) for sample of compact ceramic tile was 0 Bqm -3. The findings show that concrete brick samples are important source of radon emanation, while brown clay brick have been accepted as the recommendation of the U.S. Environmental Protection Agency (EPA), and ceramic tiles had no emanation of radon gas due to their compact surface, or the glazed layer created on the tile surface during the manufacturing process, which blocks radon emanation. A positive correlation between radon emanation and radium content has been observed for both brown clay brick and concrete brick samples whereas a negative correlation for ceramic tile has been observed. Consequently from the findings, in order to reduce radon emanation and radon exposure in house dwellings and in addition to EPA recommendation of sealed cracks and established good ventilation, we recommend concrete walls to be painted and concrete floors to be paved with ceramic tiles.

Matched MeSH terms: Ceramics
Fulltext Electrodeposition of nickel-phosphorus-alumina composite coatings

Nur Azam Badarulzaman, Ng, Jun Wei, Ahmad Azmin Mohamad, Purwadaria, Sunara, Zainal Arifin Ahmad

Journal of Nuclear and Related Technologies, 2009;2009(1):43-50.
MyJurnal

A co-deposition of nickel-phosphorus-alumina (NiPA) composite coatings were obtained from an ordinary sulphate-based plating bath consisting of 5 g/l alumina (Al2O3) particles. The particles were dispersed by using mechanical agitation at 125 rpm. The presence of Ni3P and Al2O3 phases in the coatings was confirmed by XRD analysis. SEM/EDX results indicated that a smooth Ni3P coating was obtained and Al2O3 particles were embedded into the coating. Microscopic observation showed that the bonding between the Ni3P metal matrix and the Al2O3 ceramic particles was compact.

Matched MeSH terms: Ceramics
Fulltext Sustainable Production of Arecanut Husk Ash as Potential Silica Replacement for Synthesis of Silicate-Based Glass-Ceramics Materials

Anuar MF, Fen YW, Azizan MZ, Rahmat F, Mohd Zaid MH, Khaidir REM, et al.

Materials (Basel), 2021 Feb 28;14(5).
PMID: 33670923 DOI: 10.3390/ma14051141

Arecanut husk (AH) was selected as a material for silica replacement in the synthesis process of glass-ceramics zinc silicate and also the fact that it has no traditional use and often being dumped and results in environmental issues. The process of pyrolysis was carried out at temperature 700 °C and above based on thermogravimetric analysis to produce arecanut husk ash (AHA). The average purity of the silica content in AHA ranged from 29.17% to 45.43%. Furthermore, zinc oxide was introduced to AHA and zinc silicate started to form at sintering temperature 700 °C and showed increased diffraction intensity upon higher sintering temperature of 600 °C to 1000 °C based on X-ray diffraction (XRD) analysis. The grain sizes of the zinc silicate increased from 1011 nm to 3518 nm based on the morphological studies carried out by field emission scanning electron microscopy (FESEM). In addition, the optical band gap of the sample was measured to be in the range from 2.410 eV to 2.697 eV after sintering temperature. From the data, it is believed that a cleaner production of low-cost zinc silicate can be achieved by using arecanut husk and have the potential to be used as phosphors materials.

Matched MeSH terms: Ceramics
Fulltext Self-Fluxing Mechanism in Geopolymerization for Low-Sintering Temperature of Ceramic

Jamil NH, Abdullah MMAB, Pa FC, Mohamad H, Ibrahim WMAW, Amonpattaratkit P, et al.

Materials (Basel), 2021 Mar 10;14(6).
PMID: 33801862 DOI: 10.3390/ma14061325

Kaolin, theoretically known as having low reactivity during geopolymerization, was used as a source of aluminosilicate materials in this study. Due to this concern, it is challenging to directly produce kaolin geopolymers without pre-treatment. The addition of ground granulated blast furnace slag (GGBS) accelerated the geopolymerization process. Kaolin-GGBS geopolymer ceramic was prepared at a low sintering temperature due to the reaction of the chemical composition during the initial stage of geopolymerization. The objective of this work was to study the influence of the chemical composition towards sintering temperature of sintered kaolin-GGBS geopolymer. Kaolin-GGBS geopolymer was prepared with a ratio of solid to liquid 2:1 and cured at 60 °C for 14 days. The cured geopolymer was sintered at different temperatures: 800, 900, 1000, and 1100 °C. Sintering at 900 °C resulted in the highest compressive strength due to the formation of densified microstructure, while higher sintering temperature led to the formation of interconnected pores. The difference in the X-ray absorption near edge structure (XANES) spectra was related to the phases obtained from the X-ray diffraction analysis, such as akermanite and anothite. Thermal analysis indicated the stability of sintered kaolin-GGBS geopolymer when exposed to 1100 °C, proving that kaolin can be directly used without heat treatment in geopolymers. The geopolymerization process facilitates the stability of cured samples when directly sintered, as well as plays a significant role as a self-fluxing agent to reduce the sintering temperature when producing sintered kaolin-GGBS geopolymers.

Matched MeSH terms: Ceramics
Fulltext Comparison of Foam Glass-Ceramics with Different Composition Derived from Ark Clamshell (ACS) and Soda Lime Silica (SLS) Glass Bottles Sintered at Various Temperatures

Hisham NAN, Zaid MHM, Aziz SHA, Muhammad FD

Materials (Basel), 2021 Jan 26;14(3).
PMID: 33530370 DOI: 10.3390/ma14030570

Soda lime silica (SLS) waste as the source of silica (SiO2) and ark clamshell (ACS) as the foaming agent has been utilized to fabricate the low-cost and lightweight foam glass-ceramics. A series of 1 and 6 wt% foam glass-ceramics were successfully prepared by the conventional solid-state sintering method at various sintering temperatures for 60 min. The bulk density of the samples has achieved minimum density (1.014 g/cm3) with maximum expansion (62.31%) at 6 wt% of the ACS content sintered at 800 °C for 60 min. The bulk density increases while the linear shrinkage and total porosity decrease with the progression of ACS contents and sintering temperature, where the results correspond with the FESEM micrograph. The result of XRD and FTIR transmittance spectra have shown that the formation of wollastonite crystal has occurred starting at 6 wt% of the ACS content sintered at 800 °C for 30 min. The highest mechanical performance (3.90 MPa) with an average total porosity (8.04%) is observed for the sample containing 1 wt% of ACS. It can be concluded that the composition of foam glass-ceramics (1 and 6 wt%) and sintering temperatures give significant results to the structural, physical, and mechanical properties of the fabricated foam glass-ceramics.

Matched MeSH terms: Ceramics
Low-cost silica based ceramic supported thin film composite hollow fiber membrane from guinea corn husk ash for efficient removal of microplastic from aqueous solution

Yogarathinam LT, Usman J, Othman MHD, Ismail AF, Goh PS, Gangasalam A, et al.

J Hazard Mater, 2022 02 15;424(Pt A):127298.
PMID: 34571470 DOI: 10.1016/j.jhazmat.2021.127298

In this study, an economic silica based ceramic hollow fiber (HF) microporous membrane was fabricated from guinea cornhusk ash (GCHA). A silica interlayer was coated to form a defect free silica membrane which serves as a support for the formation of thin film composite (TFC) ceramic hollow fiber (HF) membrane for the removal of microplastics (MPs) from aqueous solutions. Polyacrylonitrile (PAN), polyvinyl-chloride (PVC), polyvinylpyrrolidone (PVP) and polymethyl methacrylate (PMMA) are the selected MPs The effects of amine monomer concentration (0.5 wt% and 1 wt%) on the formation of poly (piperazine-amide) layer via interfacial polymerization over the GCHA ceramic support were also investigated. The morphology analysis of TFC GCHA HF membranes revealed the formation of a poly (piperazine-amide) layer with narrow pore arrangement. The pore size of TFC GCHA membrane declined with the formation of poly (piperazine-amide) layer, as evidenced from porosimetry analysis. The increase of amine concentration reduced the porosity and water flux of TFC GCHA HF membranes. During MPs filtration, 1 wt% (piperazine) based TFC GCHA membrane showed a lower transmission percentage of PVP (2.7%) and other suspended MPs also displayed lower transmission. The impact of humic acid and sodium alginate on MPs filtration and seawater pretreatment were also analyzed.

Matched MeSH terms: Ceramics
Fulltext The State of Starch/Hydroxyapatite Composite Scaffold in Bone Tissue Engineering with Consideration for Dielectric Measurement as an Alternative Characterization Technique

Mohd Roslan MR, Mohd Kamal NL, Abdul Khalid MF, Mohd Nasir NF, Cheng EM, Beh CY, et al.

Materials (Basel), 2021 Apr 14;14(8).
PMID: 33919814 DOI: 10.3390/ma14081960

Hydroxyapatite (HA) has been widely used as a scaffold in tissue engineering. HA possesses high mechanical stress and exhibits particularly excellent biocompatibility owing to its similarity to natural bone. Nonetheless, this ceramic scaffold has limited applications due to its apparent brittleness. Therefore, this had presented some difficulties when shaping implants out of HA and for sustaining a high mechanical load. Fortunately, these drawbacks can be improved by combining HA with other biomaterials. Starch was heavily considered for biomedical device applications in favor of its low cost, wide availability, and biocompatibility properties that complement HA. This review provides an insight into starch/HA composites used in the fabrication of bone tissue scaffolds and numerous factors that influence the scaffold properties. Moreover, an alternative characterization of scaffolds via dielectric and free space measurement as a potential contactless and nondestructive measurement method is also highlighted.

Matched MeSH terms: Ceramics
Conservative management of extensively damaged endodontically treated tooth using computer-aided design and computer-aided manufacturing-based hybrid-ceramic endocrown: A clinical report

Ang Y, Tew IM

J Conserv Dent, 2021 02 11;23(6):644-647.
PMID: 34083924 DOI: 10.4103/JCD.JCD_533_20

Restoring extensively damaged endodontically treated posterior teeth is always a challenge in dentistry. The use of endocrowns has gained popularity in restoring severely damaged endodontically treated teeth (ETT) in recent years. In this clinical report, a structurally compromised mandibular second molar with symptomatic irreversible pulpitis and normal apical tissue was endodontically treated. Surgical crown lengthening was attempted thereafter to increase the crown height. However, marginal periodontal tissue re-growth occurred after surgical crown lengthening. The tooth was subsequently restored with endocrown which was fabricated using computer-aided design and computer-aided manufacturing-based hybrid-ceramic. In conclusion, endocrown can be a viable restorative modality for ETT with compromised clinical crown height.

Matched MeSH terms: Ceramics
Strain measurements and fracture resistance of endodontically treated premolars restored with all-ceramic restorations

Seow LL, Toh CG, Wilson NH

J Dent, 2015 Jan;43(1):126-32.
PMID: 25448436 DOI: 10.1016/j.jdent.2014.10.001

OBJECTIVES: The aim of this study was to investigate the recovery of cuspal stiffness and fracture resistance in endodontically treated maxillary premolars restored with bonded ceramic inlays and onlays of various designs.
METHODS: Seventy intact premolars were selected for this study; six cavity designs were investigated: (i) mesio-occlusal-distal (MOD) inlay (I), (ii) MOD inlay with palatal cusp coverage (IPC), (iii) MOD onlay (O), (iv) MOD inlay with pulp chamber extension (IPE), (v) MOD inlay with palatal cusp coverage and pulp chamber extension (IPCPE), and (vi) MOD onlay with pulp chamber extension (OPE). Intact teeth acted as control. Strain gauges were attached to the buccal and palatal surfaces of the teeth to measure cuspal stiffness under static loading. All specimens were eventually subjected to compressive load to failure. Cuspal stiffness and fracture resistance data were analyzed using ANOVA and Tukey test.
RESULTS: The I and IPE restorations restored cuspal stiffness to 75% of the sound tooth value. The O and OPE restored teeth had stiffness values greater than that of a sound tooth. The I, IPC, O, IPE, IPCPE and OPE restored teeth demonstrated fracture strength values of 938N±113 N (s.d.), 1073N±176 N and 1317N±219 N, 893N±129 N, 1062N±153 N and 1347N±191 N respectively.
CONCLUSIONS: Within the limitations of this study, it was concluded that the all-ceramic onlay or inlay with palatal cusp coverage provided best biomechanical advantage in restoring an endodontically treated maxillary premolar tooth.
CLINICAL SIGNIFICANCE: The onlay approach which is more conservative compared to full coverage restoration is considered an appropriate approach to the restoration of endodontically treated maxillary premolars. The addition of a pulpal extension to the all-ceramic restorations, apart from being technically challenging, was not found to offer any biomechanical advantage to the restored teeth.
KEYWORDS: Endodontically treated teeth; Fracture strengths; Inlay; Onlay; Pulp chamber extension; Strains

Matched MeSH terms: Ceramics
Influence of sodalite zeolite infiltration on the coefficient of thermal expansion and bond strength of all-ceramic dental prostheses

Naji GA, Omar RA, Yahya R

J Mech Behav Biomed Mater, 2017 03;67:135-143.
PMID: 28006713 DOI: 10.1016/j.jmbbm.2016.12.007

In all-ceramic systems, a high incidence of veneer chip-off has been reported in clinical studies. Coefficient of thermal expansion (CTE) behaviour is one of the factors that may increase residual stress in the interface and influence the veneer/core bond strength. Therefore, this study aimed to evaluate the effect of sodalite zeolite-infiltration on the CTE behaviour and bond strength of different all-ceramic prostheses. The case-study groups were synthesized sodalite zeolite-infiltrated alumina (IA-SOD) and synthesized sodalite zeolite-infiltrated zirconia-toughened alumina (ZTA) (IZ-SOD), while the control groups were glass-infiltrated alumina (IA-glass) and glass-infiltrated ZTA (IZ-glass). Forty cylindrical-shaped samples measuring 5 mm in diameter and 10 mm in height were tested for CTE using a thermo-mechanical analyser machine, and forty disc-shaped ceramic samples measuring 12 mm in diameter and 1.2 ± 0.2 mm in thickness were prepared using specially designed stainless steel split mould and veneered by cylinder-shaped (2 mm high × 2 mm diameter) low-fusing porcelain (Vita VM7). The veneer/core samples were sintered and tested for shear bond strength using a high precision universal testing machine. Scanning electron microscope, stereo microscope, atomic force microscope, and energy-dispersive X-ray spectroscopy were used to investigate the structural characteristics of samples at the fracture surface. The collected data were analyzed with a one-way ANOVA and Tukey HSD test (α=.05). IZ-SOD revealed highest CTE and shear bond strength values, while the IA-glass revealed the lowest values than the other groups. There was no significant difference in CTE and bond strength among IZ-SOD, IA-SOD and IZ-glass samples (p>0.05). The experimental SOD zeolite-infiltrated samples revealed higher CTE mismatch and bond strength along with a more favourable mode of failure than did the commercial glass-infiltrated samples. Sandblast technique is considered as effective conditioning procedure for enhancing the surface roughness of SOD zeolite-infiltrated frameworks which subsequently improving the bond strength.

Matched MeSH terms: Ceramics*
Effect of Surface Treatments on the Bond Strength to Turkom-Cera All-ceramic Material

Razak AA, Abu-Hassan MI, Al-Makramani BM, Al-Sanabani FA, Al-Shami IZ, Almansour HM

J Contemp Dent Pract, 2016 Nov 01;17(11):920-925.
PMID: 27965501

AIM: The aim of this study was to evaluate the effect of surface treatments on shear bond strength (SBS) of Turkom-Cera (Turkom-Ceramic (M) Sdn. Bhd., Puchong, Malaysia) all-ceramic material cemented with resin cement Panavia-F (Kuraray Medical Inc., Okayama, Japan).
MATERIALS AND METHODS: Forty Turkom-Cera ceramic disks (10 mm × 3 mm) were prepared and randomly divided into four groups. The disks were wet ground to 1000-grit and subjected to four surface treatments: (1) No treatment (Control), (2) sandblasting, (3) silane application, and (4) sandblasting + silane. The four groups of 10 specimens each were bonded with Panavia-F resin cement according to manufacturer's recommendations. The SBS was determined using the universal testing machine (Instron) at 0.5 mm/min crosshead speed. Failure modes were recorded and a qualitative micromorphologic examination of different surface treatments was performed. The data were analyzed using the one-way analysis of variance (ANOVA) and Tukey honestly significant difference (HSD) tests.
RESULTS: The SBS of the control, sandblasting, silane, and sandblasting + silane groups were: 10.8 ± 1.5, 16.4 ± 3.4, 16.2 ± 2.5, and 19.1 ± 2.4 MPa respectively. According to the Tukey HSD test, only the mean SBS of the control group was significantly different from the other three groups. There was no significant difference between sandblasting, silane, and sandblasting + silane groups.
CONCLUSION: In this study, the three surface treatments used improved the bond strength of resin cement to Turkom-Cera disks.
CLINICAL SIGNIFICANCE: The surface treatments used in this study appeared to be suitable methods for the cementation of glass infiltrated all-ceramic restorations.

Matched MeSH terms: Ceramics/chemistry*
Light energy transmission through six different makes of ceramic orthodontic brackets

Aldossary MS, Abu Hajia SS, Santini A

Int Orthod, 2018 12;16(4):638-651.
PMID: 30385291 DOI: 10.1016/j.ortho.2018.09.005

OBJECTIVE: To measure Total Light Energy (TLE) Transmission through six makes of ceramic orthodontic brackets alone and bracket-plus-adhesive samples, using the MARC™-Resin Calibrator (RC).
METHODS: Six makes, three each monocrystalline (M) and polycrystalline (P) were used; PureSapphire (M), SPA Aesthetic (M), Ghost (M), Mist (P), Reflections (P), and Dual Ceramic (P). The Ortholux™ Light Curing Unit (LCU) was used to cure the orthodontic adhesive Transbond™XT. The LCU's tip irradiance was measured and TLE transmitted through the ceramic bracket was obtained, then adhesive added to the bracket, and transmitted TLE measured through bracket-plus-adhesive samples. The LCU was set at five seconds as recommended for curing adhesive through ceramic brackets.
RESULTS: Mean tip irradiance was 1859.2±16.2mW/cm2. The TLE transmitted through brackets alone ranged 1.7 to 3.9J/cm2, in the descending order: Ghost>Pure Sapphire>Reflections>Mist>SPA Aesthetics>Dual Ceramic. The TLE transmitted through bracket-plus-adhesive samples ranged 1.6 to 3.7J/cm2, in the descending order: Ghost>Mist>Reflections>Pure Sapphire>SPA Aesthetics>Dual Ceramic. TLE was reduced with the addition of adhesive (range -0.1 to -0.7J/cm2). There was a significant difference for Pure Sapphire, Reflections, and Mist (P<0.05), but not for SPA Aesthetics, Ghost, and Dual Ceramic. There was no overall significant difference between the monocrystalline and polycrystalline makes. The two best makes were of the monocrystalline type, concerning TLE transmission, but with the exception of polycrystalline Dual Ceramic; the next worst make was a monocrystalline bracket, SPA Aesthetics.
CONCLUSION: Light energy attenuation through ceramic orthodontic brackets is make-dependent, with no overall difference between monocrystalline and polycrystalline brackets. Light energy is further attenuated with the addition of resin-based orthodontic adhesive.

Matched MeSH terms: Ceramics/chemistry*
Fulltext Effect of sandblasting, silica coating, and erbium: Yttrium-Aluminum-Garnet laser treatment on the shear bond strength of self-adhesive resin cement to alumina ceramics

Caglar I, Ates SM, Boztoprak Y, Aslan YU, Duymus ZY

Niger J Clin Pract, 2018 Aug;21(8):1000-1007.
PMID: 30074001 DOI: 10.4103/njcp.njcp_300_17

Objective: The aim of this study was to investigate the different surface treatments on the bond strength of self-adhesive resin cement to high-strength ceramic.
Materials and Methods: Ninety aluminum oxide ceramic (Turkom-Ceramic Sdn. Bhd., Kuala Lumpur, Malaysia) specimens were produced and divided into nine groups to receive the following surface treatments: control group, no treatment (Group C), sandblasting (Group B), silica coating (Group S), erbium: yttrium-aluminum-garnet (Er:YAG) laser irradiation at 150 mJ 10 Hz (Group L1), Er:YAG laser irradiation at 300 mJ 10 Hz (Group L2), sandblasting + L1 (Group BL1), sandblasting + L2 (Group BL2), silica coating + L1 (Group SL1), and silica coating + L2 (Group SL2). After surface treatments, surface roughness (SR) values were measured and surface topography was evaluated. Resin cement was applied on the specimen surface, and shear bond strength (SBS) tests were performed. Data were statistically analyzed using one-way ANOVA and Tukey's multiple comparisons at a significance level of P < 0.05.
Results: Group S, SL1, and SL2 showed significantly increased SR values compared to the control group (P < 0.05); therefore, no significant differences were found among the SR values of Groups B, BL1, BL2, L1, and L2 and the control group (P > 0.05). Group S showed the highest SBS values, whereas the control group showed the lowest SBS values.
Conclusion: Silica coating is the most effective method for resin bonding of high strength ceramic, but Er:YAG laser application decreased the effectiveness.

Matched MeSH terms: Ceramics/chemistry*
Enhancement of thermal, mechanical and physical properties of polyamide 12 composites via hybridization of ceramics for bone replacement

Abdullah AM, Mohamad D, Rahim TNAT, Akil HM, Rajion ZA

Mater Sci Eng C Mater Biol Appl, 2019 Jun;99:719-725.
PMID: 30889745 DOI: 10.1016/j.msec.2019.02.007

This study reports the influence of ZrO2/β-TCP hybridization on the thermal, mechanical, and physical properties of polyamide 12 composites to be suited for bone replacement. Amount of 15 wt% of nano-ZrO2 along with 5,10,15,20 and 25 wt% of micro-β-TCP was compounded with polyamide 12 via a twin-screw extruder. The hybrid ZrO2/β-TCP filled polyamide 12 exhibited higher thermal, mechanical and physical properties in comparison to unfilled polyamide 12 at certain filler loading; which is attributed to the homogenous dispersion of ZrO2/β-TCP fillers particle in polyamide 12 matrix. The hybrid ZrO2/β-TCP filled PA 12 demonstrated an increment of tensile strength by up to 1%, tensile modulus of 38%, flexural strength of 15%, flexural modulus of 45%, and surface roughness value of 93%, as compared to unfilled PA 12. With enhanced thermal, mechanical and physical properties, the newly developed hybrid ZrO2/β-TCP filled PA 12 could be potentially utilized for bone replacement.

Matched MeSH terms: Ceramics/chemistry*
Porous alumina-hydroxyapatite composites through protein foaming-consolidation method

Sopyan I, Fadli A, Mel M

J Mech Behav Biomed Mater, 2012 Apr;8:86-98.
PMID: 22402156 DOI: 10.1016/j.jmbbm.2011.10.012

This report presents physical characterization and cell culture test of porous alumina-hydroxyapatite (HA) composites fabricated through protein foaming-consolidation technique. Alumina and HA powders were mixed with yolk and starch at an adjusted ratio to make slurry. The resulting slip was poured into cylindrical shaped molds and followed by foaming and consolidation via 180 °C drying for 1 h. The obtained green bodies were burned at 600 °C for 1 h, followed by sintering at temperatures of 1200-1550 °C for 2 h. Porous alumina-HA bodies with 26-77 vol.% shrinkage, 46%-52% porosity and 0.1-6.4 MPa compressive strength were obtained. The compressive strength of bodies increased with the increasing sintering temperatures. The addition of commercial HA in the body was found to increase the compressive strength, whereas the case is reverse for sol-gel derived HA. Biocompatibility study of porous alumina-HA was performed in a stirred tank bioreactor using culture of Vero cells. A good compatibility of the cells to the porous microcarriers was observed as the cells attached and grew at the surface of microcarriers at 8-120 cultured hours. The cell growth on porous alumina microcarrier was 0.015 h(-1) and increased to 0.019 h(-1) for 0.3 w/w HA-to-alumina mass ratio and decreased again to 0.017 h(-1) for 1.0 w/w ratio.

Matched MeSH terms: Ceramics/chemistry
Recent development on porous calcium phosphate ceramics for biomedical application

Sopyan I

Med J Malaysia, 2008 Jul;63 Suppl A:14-5.
PMID: 19024961

Porous calcium phosphate ceramics have found enormous use in biomedical applications including bone tissue regeneration, cell proliferation, and drug delivery. In bone tissue engineering it has been applied as filling material for bone defects and augmentation, artificial bone graft material, and prosthesis revision surgery. Their high surface area leads to excellent osteoconductivity and resorbability providing fast bone ingrowths. Porous calcium phosphate can be produced by a variety of methods. This paper discusses briefly fundamental aspects of porous calcium phosphate for biomedical applications as well as various techniques used to prepare porous calcium phosphate.

Matched MeSH terms: Ceramics*
Successful commercialisation of locally fabricated bioceramics for clinical applications

Fazan F, Besar I, Osman A, Samsudin AR, Khalid KA

Med J Malaysia, 2008 Jul;63 Suppl A:49-50.
PMID: 19024978

This paper chronicled the development of a locally produced bone graft substitute based on calcium phosphate bioceramics called "GranuMaS--from concepts to clinics, and finally to its successful commercialization all within 5-year duration. It was a Prioritized Research (PR) collaborative project of 5 institutions namely SIRIM, ANM, USM, UKM and IIUM, funded by MOSTI to the amount of approximately RM2.5 millions under RM8. This paper also highlighted the requirements needed in terms of technical expertise/manpower, facilities and infrastructure, and government/institutional supports, as well as the challenge faced in developing and commercializing such product.

Matched MeSH terms: Ceramics*

Filters

Please provide feedback to Administrator (afdal@afpm.org.my)

External Links