In radiography, radiation workers are responsible to protect patients and their caregivers from adverse effects of X-rays during diagnostic procedures. The X-ray examination rooms are designated as controlled areas where only authorised persons are allowed to enter. However, sometimes radiographers allow next in-line patients’ and caregivers in X-ray examination room and ask them to stand behind the mobile lead shielding when exposure is on. The objectives of this study were to determine the amount of scatter radiation dose at different heights with respect to the floor in the X-ray examination room and to educate and increase the awareness of radiation workers about the scattered radiation in minimizing the unnecessary radiation dose to patient’s caregivers. Siemens Multix Top X-ray system was used. Kyoto Kagaku PBU-50 whole body phantom was scanned. The phantom (torso) was positioned for anteroposterior (AP) lumbar projection on the examination table. The nanoDot OSLDs were fixed behind the lead shielding at different heights (120, 130, 140, 150, 160 and 170 cm) with respect to the floor 2.5 meters away from the central ray of X-ray beam. The phantom was exposed using different tube voltages 68 kVp, 79 kVp and 90 kVp at a constant tube current of 32 mAs fixing a 100 cm source to image distance (SID). Scatter radiation doses measured at different heights were different for each exposure. The highest scattered radiation dose measured was 6.4 mGy at 130 cm height for 79 kVp exposure. In conclusion the measured scattered radiation doses were within the acceptable annual dose limits as recommended by NCRP 116 and ICRP 103 for patient caregiver. However, a smallest amount of radiation dose may increase the risk of cancer. Thus, the negligence must not be overlooked because it exposes the caregiver to unnecessary radiation.
Conocarpus fiber is an abundantly available and sustainable cellulosic biomass. With its richness in cellulose content, it is potentially used for manufacturing microcrystalline cellulose (MCC), a cellulose derivative product with versatile industrial applications. In this work, different samples of bleached fiber (CPBLH), alkali-treated fiber (CPAKL), and acid-treated fiber (CPMCC) were produced from Conocarpus through integrated chemical process of bleaching, alkaline cooking, and acid hydrolysis, respectively. Characterizations of samples were carried out with Scanning Electron Microscope (SEM), Energy Dispersive X-ray (EDX), Fourier Transform Infrared-Ray (FTIR), X-ray Diffraction (XRD), Thermogravimetric (TGA), and Differential Scanning Calorimetry (DSC). From morphology study, the bundle fiber feature of CPBLH disintegrated into micro-size fibrils of CPMCC, showing the amorphous compounds were substantially removed through chemical depolymerization. Meanwhile, the elemental analysis also proved that the traces of impurities such as cations and anions were successfully eliminated from CPMCC. The CPMCC also gave a considerably high yield of 27%, which endowed it with great sustainability in acting as alternative biomass for MCC production. Physicochemical analysis revealed the existence of crystalline cellulose domain in CPMCC had contributed it 75.7% crystallinity. In thermal analysis, CPMCC had stable decomposition behavior comparing to CPBLH and CPAKL fibers. Therefore, Conocarpus fiber could be a promising candidate for extracting MCC with excellent properties in the future.
Critical size defects (CSD) in the long bones of New Zealand White rabbits (Oryctolagus cuniculus) have been used for years as an experimental model for investigation of the effectiveness of a new bone substitute material. There are varieties of protocols available in the literature. This technical note attempts to present an alternative surgical technique of a CSD in the New Zealand white rabbit tibia. Methods: Thirty-nine New Zealand White rabbits were used in this study. A CSD of approximately 4.5 mm (width) X 9.0 mm (length) was surgically drilled at the proximal tibial metaphysis, approximately 1 cm from the knee joint. The surrounding of soft tissue was repositioned and sutured layer by layer with bioabsorbable surgical suture. Two x-rays of anteroposterior and lateral were taken before assessed under computed tomography scan at 6, 12 and 24 weeks. Results: This alternative method created CSD with less bleeding from the muscle observed. No mortality or other surgical complications observed within 6 weeks, 12 weeks and 24 weeks following surgery. Conclusion: A simple and safe method for performing CSD was demonstrated and recommended as an alternative approach for surgery on New Zealand White rabbits.
Introduction: Melatonin (MEL) loaded alginate-chitosan/beta-tricalcium phosphate (Alg-CH/β-TCP) composite hy- drogel has been formulated as a scaffold for bone regeneration. MEL in the scaffold was anticipated to accelerate bone regeneration. The objective of this study is to observe signs of systemic toxicity and physical changes on surface defected bone for bone regenerative performance of the composite. Methods: The proximal-medial metaphyseal cortex of the left tibia of New Zealand white rabbit was the surgical site of the defect. A total of nine rabbits were randomly allocated to three groups; Group I; implanted with MEL loaded Alg-CH/β-TCP, Group II; Alg-CH/β-TCP and Group III defects were sham control. The rabbits were daily observed to determine systemic toxicity effects by composites. The physical changes to implanted site were observed using digital x-ray radiography and computerized tomography at weeks 0, 2, 4, 6 and 8 of post-implantation. Results: There were no clinical signs of systemic toxicity for all groups of rabbits. Digital radiography did not show adverse effects to the bone. Computerized tomography showed reduction in the area size and depth volume of the implantation site, but accelerated regeneration within the 8 weeks was not significantly different (P
This present study investigated the effect of Captisol, a chemically modified cyclodextrin, on the in vitro dissolution of glimepiride. We prepared glimepiride-Captisol complexes of different mass ratios (1:1, 1:2, and 1:3 w/w) by a physical mixing or freeze-drying technique, and found that complexation with Captisol enhanced the water solubility of glimepiride. Molecular docking and dynamic simulation predicted complex formation; at the same time, Fourier transform infrared spectroscopy, differential scanning calorimetry, powder X-ray diffractometry, and scanning electron microscope indicated molecular interactions that support complexation. We also found that an inclusion complex was better than a physical mixture in enhancing the complexation of glimepiride with Captisol and enhancing water solubility. Phase solubility study of the glimepiride-Captisol complex showed an AL-type profile, implying the formation of a 1:1 inclusion complex. The study also revealed that pH influenced the stability of the complex because the stability constant of the glimepiride-Captisol complex was higher in distilled water of pH ∼6.0 than in phosphate buffer of pH 7.2.
A tin oxide (SnO2) and reduced graphene oxide (rGO) hybrid composite gas sensor for high-performance carbon dioxide (CO2) gas detection at room temperature was studied. Since it can be used independently from a heater, it emerges as a promising candidate for reducing the complexity of device circuitry, packaging size, and fabrication cost; furthermore, it favors integration into portable devices with a low energy density battery. In this study, SnO2-rGO was prepared via an in-situ chemical reduction route. Dedicated material characterization techniques including field emission scanning electron microscopy (FESEM), high-resolution transmission electron microscopy (HRTEM), energy dispersive X-ray (EDX) spectroscopy, Raman spectroscopy, and X-ray photoelectron spectroscopy (XPS) were conducted. The gas sensor based on the synthesized hybrid composite was successfully tested over a wide range of carbon dioxide concentrations where it exhibited excellent response magnitudes, good linearity, and low detection limit. The synergistic effect can explain the obtained hybrid gas sensor's prominent sensing properties between SnO2 and rGO that provide excellent charge transport capability and an abundance of sensing sites.
We have developed a new class of lanthanide nano-clusters that self-assemble using flexible Schiff base ligands. Cd-Ln and Ni-Ln clusters, [Ln8Cd24(L(1))12(OAc)39Cl7(OH)2] (Ln = Nd, Eu), [Eu8Cd24(L(1))12(OAc)44], [Ln8Cd24(L(2))12(OAc)44] (Ln = Nd, Yb, Sm) and [Nd2Ni4(L(3))2(acac)6(NO3)2(OH)2], were constructed using different types of flexible Schiff base ligands. These molecular nano-clusters exhibit anisotropic architectures that differ considerably depending upon the presence of Cd (nano-drum) or Ni (square-like nano-cluster). Structural characterization of the self-assembled particles has been undertaken using crystallography, transmission electron microscopy and small-angle X-ray scattering. Comparison of the metric dimensions of the nano-drums shows a consistency of size using these techniques, suggesting that these molecules may share similar structural features in both solid and solution states. Photophysical properties were studied by excitation of the ligand-centered absorption bands in the solid state and in solution, and using confocal microscopy of microspheres loaded with the compounds. The emissive properties of these compounds vary depending upon the combination of lanthanide and Cd or Ni present in these clusters. The results provide new insights into the construction of novel high-nuclearity nano-clusters and offer a promising foundation for the development of new functional nanomaterials.
Polymer had been widely used in industries nowadays. However, the properties of the polymer itself are limited to a particular application. This study describes synthetic clay, layered double hydroxide (LDH), as a filler in low-density polyethylene (LDPE) composite. LDHs of magnesium/aluminium-dodecyl sulfate (Mg/Al-DS) and its grafted with triethoxymethylsilane (TEMS), (TEMS-g-Mg/Al-DS) were synthesized through co-precipitation and salinization reaction methods. The presence of alkyl group, v(C-H) in both LDH had confirmed through Fourier transform infrared (FTIR). The appearance of peaks in FTIR spectra within the absorbance range of 2800 – 2930 cm-1indicates a successful surface modification of LDH, supported by the changes of interlayer spacing and the presence of carbon from X-ray diffractogram and CHNS elemental analysis, respectively. The synthesized LDH was mixed with LDPE via melt intercalation method. The LDH modification resulted in higher interaction and compatibility between the LDPE matrix and LDH by the formation exfoliated type of nanocomposites, as suggested by XRD analysis.
The lyotropic phase behavior of four common and easily accessible glycosides, n-octyl α-d-glycosides, namely, α-Glc-OC8, α-Man-OC8, α-Gal-OC8, and α-Xyl-OC8, was investigated. The presence of normal hexagonal (HI), bicontinuous cubic (VI), and lamellar (Lα) phases in α-Glc-OC8 and α-Man-OC8 including their phase diagrams in water reported previously was verified by deuterium nuclear magnetic resonance (2H NMR), via monitoring the D2O spectra. Additionally, the partial binary phase diagrams and the liquid crystal structures formed by α-Gal-OC8 and α-Xyl-OC8 in D2O were constructed and confirmed using small- and wide-angle X-ray scattering and 2H NMR. The average number of bound water molecules (nb) per headgroup in the Lα phase was determined by the systematic measurement of the quadrupolar splitting of D2O over a wide range of molar ratio values (glycoside/D2O), especially at high glucoside composition. The number of bound water molecules bound to the headgroup was found to be around 1.5-2.0 for glucoside, mannoside, and galactoside, all of which possesses four OH groups. In the case of xyloside, which has only three OH groups, the bound water content is ∼2.0. Our findings confirmed that the bound water content of all n-octyl α-d-glycosides studied is lower compared to the number of possible hydrogen bonding sites possibly due to the fact that most of the OH groups are involved in intralayer interaction that holds the lipid assembly together.
A rapid, sustainable, and ecologically sound approach is urgently needed for the production of semiconductor nanomaterials. CuSe nanoparticles (NPs) were synthesized via a microwave-assisted technique using CuCl2·2H2O and Na2SeO3 as the starting materials. The role of the irradiation time was considered as the primary concern to regulate the size and possibly the shape of the synthesized nanoparticles. A range of characterization techniques was used to elucidate the structural and optical properties of the fabricated nanoparticles, which included X-ray diffraction, energy-dispersive X-ray spectroscopy (EDX), atomic force microscopy, field emission scanning electron microscopy, Raman spectroscopy (Raman), UV-Visible diffuse reflectance spectroscopy (DRS), and photoluminescence spectroscopy (PL). The mean crystallite size of the CuSe hexagonal (Klockmannite) crystal structure increased from 21.35 to 99.85 nm with the increase in irradiation time. At the same time, the microstrain and dislocation density decreased from 7.90 × 10-4 to 1.560 × 10-4 and 4.68 × 10-2 to 1.00 × 10-2 nm-2, respectively. Three Raman vibrational bands attributed to CuSe NPs have been identified in the Raman spectrum. Irradiation time was also seen to play a critical role in the NP optical band gap during the synthesis. The decrease in the optical band gap from 1.85 to 1.60 eV is attributed to the increase in the crystallite size when the irradiation time was increased. At 400 nm excitation wavelength, a strong orange emission centered at 610 nm was observed from the PL measurement. The PL intensity is found to increase with an increase in irradiation time, which is attributed to the improvement in crystallinity at higher irradiation time. Therefore, the results obtained in this study could be of great benefit in the field of photonics, solar cells, and optoelectronic applications.
In this study, a series of copper-ion-doped titanium dioxide (Cu-ion-doped TiO₂) nanotubes (NTs) were synthesized via a hydrothermal method by the concentration variation of doped Cu ions (0.00, 0.50, 1.00, 2.50, and 5.00 mmol). In addition, the samples were characterized using X-ray diffraction (XRD), field-emission scanning electron microscopy (FE-SEM), transmission electron microscopy (TEM), energy-dispersive X-ray spectroscopy (EDX), nitrogen gas adsorption measurements, and ultraviolet-visible (UV-Vis) diffuse-reflectance spectroscopy. The photocatalytic activity of the Cu-iondoped TiO₂ NTs was investigated for the degradation of methyl orange (MO) under sunlight. The results obtained from the structural and morphological studies revealed that, at low concentrations of Cu-doped TiO₂ NTs, Cu is incorporated into the interstitial positions of the TiO₂ lattice, affording a new phase of TiO₂ (hexagonal) instead of the anatase TiO₂ (tetragonal) observed for undoped TiO₂ NTs. EDX analysis confirmed the presence of Cu in the TiO₂-based photocatalyst. All of the investigated samples exhibited a hollow fibrous-like structure, indicative of an NT morphology. The inner and outer diameters of the NTs were 4 nm and 10 nm, respectively. The photocatalysts exhibited a large surface area due to the NT morphology and a type IV isotherm and H3 hysteresis, corresponding to the mesopores and slit-shaped pores. The Cu-ion-doped TiO₂ NTs were excited by sunlight because of their low bandgap energy; and after the incorporation of Cu ions into the interstitial positions of the TiO₂ lattice, the NTs exhibited high visible-light activity owing to the low bandgap.
Au-Ag alloy nanoparticles are physically synthesized using rapid, simple and efficient Q-switched Nd:YAG pulsed laser ablation in liquid technique (PLAL). Au and Ag colloidal solutions are separately prepared by 1064 nm laser ablation of metallic target (gold and silver) which is immersed in deionized water. Au-Ag alloy nanoparticles are prepared by irradiating the mixture of Au and Ag colloidal solutions with 532 nm of second harmonic wavelength of Nd:YAG laser at three different ratio, 3:1, 1:1 and 1:3 within different exposure times. The three of plasmon absorption bands of Au-Ag nanoparticles are shifted linearly to the lower wavelength [499.67 nm (3:1), 481.25 nm (1:1), 467.91 nm (1:3)], as compared to plasmon absorption spectra of pure Au (520 nm) and Ag (400 nm). Moreover, the change in colors are also observed from red (Au) and yellow (Ag) to orange, brown and green color due to the Au-Ag alloy formations, respectively. Transmission electron microscopy shows the Ag shell around the inner core of Au spherical metal with broad size distribution due to the three different volume ratio, respectively (1.7 nm, 0.7 nm, 1.4 nm). Energy-dispersive X-ray spectroscopy analysis confirms the presence of Au and Ag elements in Au-Ag alloy nanoparticles without any contaminations. Attenuated total reflectance fourier transform infrared spectroscopy analysis also confirms the homogenous Au-Ag alloys chemical bonding.
Phenolic resin-silica nanocomposites samples in pellet shape have been successfully prepared by intercalation of polymer solution through the hot pressing method. The phenolic resin is modified with organic elastomers of silica nanoparticles, which is about 20 nanometer in diameter. The change of density and porosity was studied based on the addition of silica content in the phenolic resin composites. The densities of composites increased with the addition of the silica content from 10 wt.% to 40 wt.%. On the other hand, the porosity percentage was decreased with increasing of silica contents. The mechanical properties (Young’s modulus, energy to break and time to failure) of the nanocomposites samples were identified using the Universal Testing Material Machine (UTM). The results of Young’s modulus, energy to break and time to failure of the phenolic resin composites were found to be slightly increased with silica content from 10 wt.% to 30 wt.%. The X-Ray Microtomogaphy (XRM) topographies have shown that the porosity exists on fracture structure for each nanocomposite. The nanocomposites surface structure has been analyzed using Scanning Electron Microscope (SEM). The observation shows that the fracture surface of the pure phenolic resin is relatively smooth and glassy, which is typical for a brittle material, but the phenolic resin- silica composites fracture surface is not smooth at all. The observations indicate the pure phenolic resin is brittle than phenolic resin-silica nanocomposites. Consequently, the physical properties of the phenolic resin-silica nanocomposites were improved with the addition of 10 wt.% to 30 wt.% silica contents, as compared to that of the pure phenolic resin.
In these studies, cordierite was mechanically synthesized after a sol-gel process. The effect of milling time of cordierite was investigated. Aluminium nitrate nonahydrate, magnesium nitrate hexahydrate and tetraethylorthosilicate (TEOS) were used as starting materials. Gels obtained were mechanically activated in planetary ball mill by at 300rpm grinding speed and grinding time (15min, 30min, 45min and 60min). Powders produced were characterized by X-Ray Diffraction (XRD) and Field Emission Scanning Electron Microscope (FESEM) and Energy Dispersive X-Ray (EDX). XRD analysis proved that α-cordierite was formed at lower temperature (1200°C) as compliment to without grinding, whereby it is formed at1300°C. FESEM analysis shows the size of the cordierite were in submicron scale. EDX analysis proved that magnesium, aluminium, silicon and oxygen are elements existed in cordierite.
In this study, we evaluated and characterized microbial cellulose produced from Kombucha after eighth day of fermentation by employing SEM, FTIR, X-ray diffractometry, adsorption isotherm, and by measuring the swelling properties. Results on SEM revealed microbial cellulose layer to be composed of a compact cellulose ultrafine network like structure. FTIR spectra showed the presence of a characteristic region of anomeric carbons (960 – 730 cm-1), wherein a band at 891.59 cm-1 confirmed the presence of β, 1-4 linkages. Results of FTIR spectra also showed microbial cellulose to be free from contaminants such as lignin or hemicellulose, which are often present in plant cellulose. X-ray diffraction studies exhibited the overall degree of crystallinity index for MCC to be slightly lower than that of microbial cellulose. Results on swelling properties indicated microbial cellulose to possess higher fiber liquid retention values (10-160%) compared to commercial MCC (5-70%). The adsorption isotherm curves showed similarities between microbial cellulose with that of pure crystalline substance. Overall, results obtained in this study were comparable with the commercial microcrystalline cellulose, indicating that the process developed by us can be explored industrially on a pilot scale.
The popularity of ultrasound for acute diagnosis of fractures in the Emergency Department (ED) has increased over the recent years. This present study aimed to determine the sensitivity and specificity of ultrasound use for detection of fractures in a different environment, which is at the triage area of the ED. We compared the results of bedside ultrasound in detecting non-critical fractures to the current gold standard of X-rays in the triage area. The design was a single centered crosssectional study. From August 2014 till November 2014, a total of 46 patients were recruited, creating 75 image pairs. Following consent, a bedside ultrasound was performed and subsequently compared with X-ray reporting regarding the presence or absence of fractures. SPSS analysis was used to determine the sensitivity and specificity of ultrasound in diagnosing fracture as compared to X-rays. Ultrasound had a sensitivity of 72% (95% CI, 50.6% - 87.9%) and a specificity of 80% (95%CI: 66.3 - 90%) when compared to X-rays in fracture diagnosis. The kappa analyses showed moderate inter observer agreement (0.5) between ultrasound and X-rays in diagnosing fractures. This study suggests that the use of ultrasound as a triage tool yet has unacceptable sensitivity and needs further evaluation and consideration.
Chemical composition of fine (PM2.5) aerosol samples collected for the 5 years period (2001- 2005) using Gent Stacked filter unit sampler at Klang Valley (3 o 10 ’ 30 ’’ N, 101 o 43 ’ 24 ’’ E) were analysed using Neutron Activation Analysis (NAA) and Proton Induced X-ray Emission (PIXE). Results of the study show that the major component of the fine aerosol was black carbon and sulfur with the mass concentration ranged from 4.4 - 6.7µg m -3 and 1.2 - 1.9µg m -3 , respectively. The total fine aerosol mass concentration were in the ranged of 25 - 31µg m -3 with the reconstructed mass was about 50% as relative to the gravimetric mass. Statistical method, factor analysis with varimax approach has been applied to the aerosol composition data for the fingerprint identification. The analysis produces five identified fingerprint represent soil, industry, motor vehicles/biomass burning and Pb and Zn sources. There is also an unidentified source that could be related to unknown industrial activities.
This descriptive cross sectional study was conducted to assess patient's satisfaction by evaluating the waiting time experienced by 27 (54%) inpatients and 23 (46%) outpatients who sought treatment at a private hospital in Selangor from 15th of May 2006 until 3rd of]une 2006. Majority of the patients (78%) were in the range between Z 1 - 40 years old and well»educated. Almost half (48%) were in the human resources employment category, 20% were in administration and marketing and 10% were professionals. Majority of them earned from RM1000-1999 (34%) and RMZ000-3999 (32%). Almost all of them (96%) agreed that the medical care that they had been receiving in the hospital was just about perfect. 98% agreed that the doctors treated them in a very friendly and courteous manner and 96% rated the care given by nurses as g0od/ excellent. 88% to 92% said that their communication with the doctors, nurses and other staff were good/ excellent. 80% waited less than 15 minutes at the registration counter, 52% waited less than 15 minutes to see the doctor and 44% waited less than 15 minutes at other places such as pharmacy and x-ray. Overall, 94% rated the level of services in the hospital as good/ excellent, Almost all (90%) would like to recommend the hospital to their friends and relatives. Our study demonstrated that the majority of the patients were satisfied with the doctors, nurses and environment of the private hospital. The average waiting time of patient before being attended to by a doctor was less than 30 minutes.
Study site: Pusat Perubatan Universiti Kebangsaan Malaysia (PPUKM)
Taman Negara is a famous tourism destination for nature lover in Malaysia. The area is well kept from human activities and disturbances. Since there is no data for human exposure to natural radiation, there is a need to do this study. It will give a baseline data for surface dose and radionuclide concentrations and one can estimate the external hazards index for the visitor to this unexplored area, i.e. UiTM-Perhilitan research station, Kuala Keniam, Taman Negara, Malaysia. The surface dose rate measurements were done in-situ using portable radiation survey meter at the surface and 1 m above the surface. The top soil samples were taken using hand auger up to 15 cm depth at nine locations around research station. Samples were brought back to the UiTM laboratory in Shah Alam, dried, ground to powder form, and sieved using 250 μm sieve. Then the uranium and thorium concentrations were analyzed using Energy Dispersive X-Ray Fluorescence (EDXRF).The mean value for surface dose rates on surface were 0.164 μSv/hr while the mean value for surface dose rates on 1m above the surface were 0.161 μSv/hr. The mean concentration of thorium was 2.62μg/g while the mean concentration of uranium was 0.61μg/g.
Changes in molecular structure configuration during strain induced crystallisation of an amorphous Poly(Lactic Acid) (PLA 4032D) polymer was monitored in-situ by simultaneously recording the wide angle x-ray scattering (WAXS) and small angle x-ray scattering (SAXS) patterns together with polymer deformation images and force data. The amorphous chain orientation from the beginning of deformation until the onset of crystallisation was studied from the WAXS patterns. The true mechanical behaviour described by the true stress-true strain curve related to an amorphous chain orientation exhibited a linear behaviour. Approaching critical amorphous orientation, the true stress-true strain curve deviated from linear into non-linear behaviour. After the onset of crystallization, when the deformed polymer became a semicrystalline state, the true mechanical behaviour exhibited true strain hardening which greatly affected by the formation of the morphology. The gradual true strain hardening was associated with the formation of micro-fibrillar structure containing thin crystallite morphology whilst sharp increased in true strain hardening was associated with the formation of stacked lamellar morphology in the form of macro-lattice structure. The study was accomplished by the application of high brilliance synchrotron radiation at beamline ID2 of ESRF, Grenoble in France and the usage of the high contrast resolution of WAXS and SAXS charge-couple device (CCD) camera as well as 40 milliseconds temporal resolution of data acquisition system.