Investigation was made of the optical response of metal-dielectric stacks-based cavity structures embedded with graphene microheaters for the purpose of perfect absorption. The absorber configuration exploits the Ge2Sb2Te5 (GST) phase changing medium, and the effects of different parametric and operational conditions on the absorption spectra were explored. The refractive indices of GST layers can be manipulated by the external electrical pulses applied to microheaters. The amplitude and duration of electrical pulses define the crystallinity ratio of the used GST mediums. The results revealed achieving perfect absorption (> 99%) in the visible and infrared (IR) regimes of the electromagnetic spectrum upon incorporating two thin GST layers of different thicknesses (in the stack) in the amorphous state. The proposed configuration showed the capability of introducing independent transition state (amorphous and/or crystalline) for each GST layer-the visible regime could be extended to the IR regime, and the perfect absorption peak in the IR regime could be broadened and red-shifted. It is expected that the structure would find potential applications in active photonic devices, infrared imaging, detectors and tunable absorbers.
This article describes a dielectrophoresis (DEP)-based simulation and experimental study of human epidermal keratinocyte (HEK) cells for wounded skin cell migration toward rapid epithelialization. MyDEP is a standalone software designed specifically to study dielectric particles and cell response to an alternating current (AC) electric field. This method demonstrated that negative dielectrophoresis (NDEP ) occurs in HEK cells at a wide frequency range in highly conductive medium. The finite element method was used to characterize particle trajectory based on DEP and drag force. The performance of the system was assessed using HEK cells in a highly conductive EpiLife suspending medium. The DEP experiment was performed by applying sinusoidal wave AC potential at the peak-to-peak voltage of 10 V in a tapered aluminum microelectrode array from 100 kHz to 1 MHz. We experimentally observed the occurrence of NDEP, which attracted HEK cells toward the local electric field minima in the region of interest. The DIPP-MotionV software was used to track cell migration in the prerecorded video via an automatic marker and estimate the average speed and acceleration of the cells. The results showed that HEK cell migration was accomplished approximately at 6.43 μm/s at 100 kHz with 10 V, and FDEP caused the cells to migrate and align at the target position, which resulted in faster wound closures because of the application of an electric field frequency to HEK cells in random locations.
A thin film of single-walled carbon nanotube (SWCNT) network field-effect transistor (FET) was fabricated by a simple, fast, and reliable deposition method for electronic applications. This study aims to develop a method for fabricating a thin film of random SWCNTs to be used as a transducer to detect human serum albumin (HSA) in biosensor applications. The random SWCNT network was deposited using the airbrush technique. The morphology of the CNT network was examined by utilising atomic force microscopy (AFM) and field-emission scanning electron microscopy (FESEM), while electrical characteristics were analysed using three-terminal IV measurements. The thin film (SWCNT network) was applied as a transducer to detect human serum albumin (HSA) based on its covalent interaction with antibodies. HSA plays a significant part in the physiological functions of the human body. The surface alteration of the SWCNTs was verified using Fourier transform infrared (FTIR) spectroscopy. Electrical current-voltage measurements validated the surface binding and HSA detection. The biosensor linearly recorded a 0.47 fg/mL limit of detection (LOD) and a high sensitivity of 3.44 μA (g/mL)-1 between 1 fg/mL and 10 pg/mL. This device can also be used to identify a genuine HSA despite interference from other biomolecules (i.e., bovine serum albumin (BSA)), thus demonstrating the random SWCNT-FET immunosensor ability to quantify HSA in a complex biological environment.
Dielectrophoresis (DEP) is a technique to manipulate trajectories of polarisable particles in nonuniform electric fields by utilizing unique dielectric properties. The manipulation of a cell using DEP has been demonstrated in various modes, thereby indicating potential applications in the biomedical field. In this review, recent DEP applications in the biomedical field are discussed. This review is intended to highlight research work that shows significant approach related to DEP application in biomedical field reported between 2016 and 2020. First, single-shell model and multiple-shell model of cells are introduced. Current device structures and recently introduced electrode patterns for DEP applications are discussed. Second, the biomedical uses of DEP in liquid biopsies, stem cell-based therapies, and diagnosis of infectious diseases due to bacteria and viruses are presented. Finally, the challenges in DEP research are discussed, and the reported solutions are explained. DEP's potential research directions are mentioned.
Thermoelectric generators (TEGs) are a form of energy harvester and eco-friendly power generation system that directly transform thermal energy into electrical energy. The thermoelectric (TE) method of energy harvesting takes advantage of the Seebeck effect, which offers a simple solution for fulfilling the power-supply demand in almost every electronics system. A high-temperature condition is commonly essential in the working mechanism of the TE device, which unfortunately limits the potential implementation of the device. This paper presents an in-depth analysis of TEGs at low operating temperature. The review starts with an extensive description of their fundamental working principles, structure, physical properties, and the figure of merit (ZT). An overview of the associated key challenges in optimising ZT value according to the physical properties is discussed, including the state of the art of the advanced approaches in ZT optimisation. Finally, this manuscript summarises the research status of Bi2Te3-based semiconductors and other compound materials as potential materials for TE generators working at low operating temperatures. The improved TE materials suggest that TE power-generation technology is essential for sustainable power generation at near-room temperature to satisfy the requirement for reliable energy supplies in low-power electrical/electronics systems.
In this work, an environmental friendly RC/N-TiO2 nanocomposite thin film was designed as a green portable photocatalyst by utilizing recycled newspaper as sustainable cellulose resource. Investigations on the influence of N-doped TiO2 nanorods incorporation on the structural and morphological properties of RC/N-TiO2 nanocomposite thin film are presented. The resulting nanocomposite thin film was characterized by FESEM, AFM, FTIR, UV-vis-NIR spectroscopy, and XPS analysis. The results suggested that there was a remarkable compatibility between cellulose and N-doped TiO2 nanorods anchored onto the surface of the RC/N-TiO2 nanocomposite thin film. Under UV and visible irradiation, the RC/N-TiO2 nanocomposite thin film showed remarkable photocatalytic activity for the degradation of methylene blue solution with degradation percentage of 96% and 78.8%, respectively. It is crucial to note that the resulting portable photocatalyst produced via an environmental and green technique in its fabrication process has good potential in the field of water and wastewater treatment application.
Biosensors operating based on electrical methods are being accelerated toward rapid and efficient detection that improve the performance of the device. Continuous study in nano- and material-sciences has led to the inflection with properties of nanomaterials that fit the trend parallel to the biosensor evolution. Advancements in technology that focuses on nano-hybrid are being used to develop biosensors with better detection strategies. In this sense, titanium dioxide (TiO2) nanomaterials have attracted extensive interest in the construction of electrical biosensors. The formation of TiO2 nano-hybrid as an electrical transducing material has revealed good results with high performance. The modification of the sensing portion with a combination (nano-hybrid form) of nanomaterials has produced excellent sensors in terms of stability, reproducibility, and enhanced sensitivity. This review highlights recent research advancements with functional TiO2 nano-hybrid materials, and their victorious story in the construction of electrical biosensors are discussed. Future research directions with commercialization of these devices and their extensive utilizations are also discussed.
Semiconductor materials have shown a good photocatalytic behaviour for the photodegradation of organic pollutants. In this work, maleated liquid natural rubber (MLNR) based hydrogel supported bismuth ferrite (BiFeO3) as photocatalyst was successfully synthesized by crosslinking with acrylic acid (AAc) assisted by the ultrasonication method to study the efficiency for the removal of methylene blue (MB) dye in wastewater. Response surface methodology (RSM) was used to optimize the parameters for adsorption of the methylene blue (MB) dye compound, whereby the effects of the initial concentration of MB and the adsorption time were examined to obtain a quadratic model for the respective hydrogel composite. The prepared composite sample was characterized by Fourier Transform Infrared (FTIR) spectroscopy, Scanning Electron Microscopy-Energy Dispersive X-ray (SEM-EDX) and X-ray Diffraction (XRD) analysis. Remarkable improvement for removal of methylene blue (99% removal) was found within 3 h adsorption time with a MLNR/AAc-BiFeO3 hydrogel composite as compared to the pristine hydrogel. A synergistic mode of dye removal by adsorption and photodegradation is proposed. Based on the isotherm and kinetic study conducted, it was found that Freundlich isotherm model and a pseudo second-order kinetic model was best fitted for adsorption of MB dye. The MLNR/AAc-BiFeO3 composite maintains its removal efficiency after 5 cycles without the necessity of post-treatment separation. Therefore, it is crucial to note that the resultant low-cost MLNR/AAc-BiFeO3 hydrogel composite in this study offers excellent potential for water and wastewater treatment applications with improved recyclability and recovery.
We fabricated copper oxide nanowires (CuO NWs) ultraviolet (UV) light-assisted hydrogen gas sensor. The fabricated sensor shows promising sensor response behavior towards 100 ppm of H2 at room temperature and elevated temperature at 100 °C when exposed to UV light (3.0 mW/cm2). One hundred-cycle device stability test has been performed, and it is found that for sample elevated at 100 °C, the UV-activated sample achieved stability in the first cycle as compared to the sample without UV irradiation which needed about 10 cycles to achieve stability at the initial stage, whereas the sample tested at room temperature was able to stabilize with the aid of UV irradiation. This indicates that with the aid of UV light, after some "warming up" time, it is possible for the conventional CuO NW sensor which normally work at elevated temperature to function at room temperature because UV source is speculated to play a dominant role to increase the interaction of the surface of CuO NWs and hydrogen gas molecules absorbed after the light exposure.
Reports of pharmaceuticals exist in surface water and drinking water around the world, indicate they are ineffectively remove from water and wastewater using conventional treatment technologies. The potential of adverse effect of these pharmaceuticals on public health and aquatic life, also their continuos accumulation have raised the development of water treatment technologies. Hybrid treatment processes like membrane filtration and advance oxidation processes (AOPs) are likely to give rise to efficient simultaneous degradation and separation mechanisms. Conventional membrane filtration techniques can remove the majority of contaminants, but the smallest, undegraded, and stabilized pharmaceutical wastes persist in the treated water. After some 20 years, researchers have recognized the important role of AOPs in the treatment of pharmaceutical wastewater because these technologies are capable of oxidizing recalcitrant, toxic, and non-biodigradable compounds into numerous by-products and finally, inert end-products via the intermediacy of hydroxyl and other radicals. Evidently, membranes are subjected to the fouling phenomenon by the contaminants in wastewater, hence resulting in a reduction of clean water flux and increase in energy demand. In such situations, these membrane hybrid AOPs exert a complementary effect in the elimination of membrane fouling, thus enhancing the performance of the membrane. Therefore, in this review, we describe the basic aspects of the removal and transformation of certain pharmaceuticals via membranes and AOPs. In addition, information and evidences on membrane hybrid AOPs in the field of pharmaceutical wastewater treatment is also presented.
Vertically standing MoS2 nanoflakes are favourable in applications such as energy storage devices, hydrogen evolution reactions, and gas sensors due to their large surface area and high density of exposed edges. In this work, we report the effect of Mo vapor concentration on the morphology of vertical MoS2 nanoflakes prepared by chemical vapor deposition at atmospheric pressure. A series of MoS2 samples were grown under different Mo vapor concentrations by varying the separation distance (x) between the MoO3 source and the substrate. Field emission scanning electron microscopy showed the sample grown at x = 1 cm had a high density of vertical flakes (7 vertical flakes µm-2) with an average flake length of ~770 nm and thickness of ~10 nm. As x increased to 4 cm, the average flake length was reduced to ~150 nm while the flake orientation changed from vertical to lateral. That is, high Mo vapor concentration favours the formation of large and vertical MoS2 nanoflakes. However, oversupply of Mo vapor results in significantly thicker flakes. Raman spectra of all samples showed two main peaks at 380 and 407 cm-1 that correspond to the E12g and A1g vibrational peaks of MoS2. As x decreased from 4 to 1, the peak intensity ratio (E12g/A1g) reduced from 0.58 to 0.42, suggesting greater dominance of vertical flakes at low x. X-ray diffraction data showed a prominent peak at 14.4°, which corresponded to the (002) diffraction peak of 2H MoS2. Transmission electron microscopy verified the flakes consist of eight layers with an interlayer spacing of 0.62 nm. Based on hydrogen evolution reaction measurements, samples with thin flakes have high catalytic activity. This work highlights the importance of optimizing Mo vapor concentration to obtain a high density of thin, large, and vertically standing MoS2 nanoflakes.
This article provides an overview of the structural and physicochemical properties of stable carbon-based nanomaterials and their applications as counter electrodes (CEs) in dye-sensitized solar cells (DSSCs). The research community has long sought to harvest highly efficient third-generation DSSCs by developing carbon-based CEs, which are among the most important components of DSSCs. Since the initial introduction of DSSCs, Pt-based electrodes have been commonly used as CEs owing to their high-electrocatalytic activities, thus, accelerating the redox couple at the electrode/electrolyte interface to complete the circuit. However, Pt-based electrodes have several limitations due to their cost, abundance, complicated facility, and low corrosion resistance in a liquid electrolyte, which further restricts the large-area applications of DSSCs. Although carbon-based nanostructures showed the best potential to replace Pt-CE of DSSC, several new properties and characteristics of carbon-CE have been reported for future enhancements in this field. In this review, we discuss the detailed synthesis, properties, and performances of various carbonaceous materials proposed for DSSC-CE. These nano-carbon materials include carbon nanoparticles, activated carbon, carbon nanofibers, carbon nanotube, two-dimensional graphene, and hybrid carbon material composites. Among the CE materials currently available, carbon-carbon hybridized electrodes show the best performance efficiency (up to 10.05%) with a high fill factor (83%). Indeed, up to 8.23% improvements in cell efficiency may be achieved by a carbon-metal hybrid material under sun condition. This review then provides guidance on how to choose appropriate carbon nanomaterials to improve the performance of CEs used in DSSCs.
Alpha (α)- and beta (β)-phase gallium oxide (Ga2O3), emerging as ultrawide-band gap semiconductors, have been paid a great deal of attention in optoelectronics and high-performance power semiconductor devices owing to their ultrawide band gap ranging from 4.4 to 5.3 eV. The hot-wall mist chemical vapor deposition (mist-CVD) method has been shown to be effective for the growth of pure α- and β-phase Ga2O3 thin films on the α-Al2O3 substrate. However, challenges to preserve their intrinsic properties at a critical growth temperature for robust applications still remain a concern. Here, we report a convenient route to grow a mixed α- and β-phase Ga2O3 ultrathin film on the α-Al2O3 substrate via mist-CVD using a mixture of the gallium precursor and oxygen gas at growth temperatures, ranging from 470 to 700 °C. The influence of growth temperature on the film characteristics was systematically investigated. The results revealed that the as-grown Ga2O3 film possesses a mixed α- and β-phase with an average value of dislocation density of 1010 cm-2 for all growth temperatures, indicating a high lattice mismatch between the film and the substrate. At 600 °C, the ultrathin and smooth Ga2O3 film exhibited a good surface roughness of 1.84 nm and an excellent optical band gap of 5.2 eV. The results here suggest that the mixed α- and β-phase Ga2O3 ultrathin film can have great potential in developing future high-power electronic devices.
The telemedicine service concept was mainly established to benefit the underprivileged people from rural areas of a country. However, due to the low literacy and awareness rates among rural population of Bangladesh, the service is not much effective. This paper represents a study on the awareness of the rural population of telemedicine service in Bangladesh and few key findings indicate how the awareness could be increased. The research also suggests that utilizing blockchain technology can enhance the data security and privacy. The research reveals some of the findings which can raise the awareness and popularity of telemedicine service among rural population. We have proposed implementation of blockchain technology which can vastly improve the security issue.
The presence of Ti3+ in the structure of TiO2 nanotube arrays (NTs) has been shown to enhance the photoelectrochemical (PEC) water-splitting performance of these NTs, leading to improved results compared to pristine anatase TiO2 NTs. To further improve the properties related to PEC performance, we successfully produced TiO2 NTs using a two-step electrochemical anodization technique, followed by annealing at a temperature of 450 °C. Subsequently, Mo2C was decorated onto the NTs by dip coating them with precursors at varying concentrations and times. The presence of anatase TiO2 and Ti3O5 phases within the TiO2 NTs was confirmed through X-ray diffraction (XRD) analysis. The TiO2 NTs that were decorated with Mo2C demonstrated a photocurrent density of approximately 1.4 mA cm-2, a value that is approximately five times greater than the photocurrent density exhibited by the bare TiO2 NTs, which was approximately 0.21 mA cm-2. The observed increase in photocurrent density can be ascribed to the incorporation of Mo2C as a cocatalyst, which significantly enhances the photocatalytic characteristics of the TiO2 NTs. The successful deposition of Mo2C onto the TiO2 NTs was further corroborated by the characterization techniques utilized. The utilization of field emission scanning electron microscopy (FESEM) allowed for the observation of Mo2C particles on the surface of TiO2 NTs. To validate the composition and optical characteristics of the decorated NTs, X-ray photoelectron spectroscopy (XPS) and UV absorbance analysis were performed. This study introduces a potentially effective method for developing efficient photoelectrodes based on TiO2 for environmentally sustainable hydrogen production through the use of photoelectrochemical water-splitting devices. The utilization of Mo2C as a cocatalyst on TiO2 NTs presents opportunities for the advancement of effective and environmentally friendly photoelectrochemical (PEC) systems.
This paper reports the development of ZnO NRs/rGO-based photocatalysts integrated into a tree-branched polymer-based microfluidic reactor for efficient photodegradation of water contaminants. The reactor system includes a photocatalytic reactor, tree-branched microfluidic channels, and ZnO nanorods (NRs) coated with reduced graphene oxide (rGO) on a glass substrate within an area of 0.6 × 0.6 cm2. The ZnO NRs/rGO acts as a photocatalyst layer grown hydrothermally and then spray-coated with rGO. The microfluidic system is made of PDMS and fabricated using soft lithography (micro molding using SU-8 master mold patterned on a silicon wafer). The device geometry is designed using AutoCAD software and the flow properties of the microfluidics are simulated using COMSOL Multiphysics. The microfluidic platform's photocatalytic process aims to bring the nanostructured photocatalyst into very close proximity to the water flow channel, reducing the interaction time and providing effective purification performance. Our functionality test showed that a degradation efficiency of 23.12 %, within the effective residence time of less than 3 s was obtained.
Cellulose continues to play an important and emerging role in photocatalysis, and its favourable properties, such as electron-rich hydroxyl groups, could enhance the performance of photocatalytic reactions. For the first time, this study exploited the kapok fibre with microtubular structure (t-KF) as a solid electron donor to enhance the photocatalytic activity of C-doped g-C3N4 (CCN) via ligand-to-metal-charge-transfer (LMCT) to improve hydrogen peroxide (H2O2) production performance. As confirmed by various characterisation techniques, the hybrid complex consisting of CCN grafted on t-KF was successfully developed in the presence of succinic acid (SA) as a cross-linker via a simple hydrothermal approach. The complexation formation between CCN and t-KF results in the CCN-SA/t-KF sample displaying a higher photocatalytic activity than pristine g-C3N4 to produce H2O2 under visible light irradiation. The enhanced physicochemical and optoelectronic properties of CCN-SA/t-KF imply that the LMCT mechanism is crucial in improving photocatalytic activity. This study promotes utilising the unique t-KF material's properties to develop a low-cost and high-performance cellulose-based LMCT photocatalyst.
Two-dimensional materials have attracted intensive attention recently due to their unique optical and electronic properties and their promising applications in water splitting and solar cells. As a representative layer-structured of transition metal dichalcogenides, MoS2has attracted considerable devotion owing to its exceptional photo and electro properties. Here, we show that the chemical vapour deposition (CVD) growth of MoS2on Si photocathode and graphene/Si photocathode can be used to prepare photoelectrocatalysts for water splitting. We explore a bottom-up method to grow vertical heterostructures of MoS2and graphene by using the two-step CVD. Graphene is first grown through ambient-pressure CVD on a Cu substrate and then transferred onto SiO2/Si substrate by using the chemical wet transfer followed by the second CVD method to grow MoS2over the graphene/SiO2/Si. The effect of the growth temperatures of MoS2is studied, and the optimum temperature is 800 °C. The MoS2produced at 800 °C has the highest photocurrent density at -0.23 mA cm-2in 0.5 M Na2SO4and -0.51 mA cm-2in 0.5 M H2SO4at -0.8 V vs. Ag/AgCl. The linear sweep voltammetry shows that MoS2in 0.5 M H2SO4has about 55% higher photocurrent density than MoS2in Na2SO4due to the higher protons (H+) in the H2SO4electrolyte solution, which are sufficiently charged to reduce to H2and, therefore hydrogen evolves more rapidly where the photocurrent density and hydrogen generation can be enhanced. MoS2/graphene/SiO2/Si (MGS) has -0.07 mA cm-2at -0.8 V vs. Ag/AgCl of photocurrent density, which is 70% lower than that of bare MoS2because MGS is thicker compared with MoS2. Thus, MoS2has potential as a photocatalyst in photoelectrochemical water splitting. The structure and the morphology of MoS2play an important role in determining the photocurrent performance.
Diabetes patients are at risk of having chronic wounds, which would take months to years to resolve naturally. Chronic wounds can be countered using the electrical stimulation technique (EST) by dielectrophoresis (DEP), which is label-free, highly sensitive, and selective for particle trajectory. In this study, we focus on the validation of polystyrene particles of 3.2 and 4.8 μm to predict the behavior of keratinocytes to estimate their crossover frequency (fXO) using the DEP force (FDEP) for particle manipulation. MyDEP is a piece of java-based stand-alone software used to consider the dielectric particle response to AC electric fields and analyzes the electrical properties of biological cells. The prototypic 3.2 and 4.8 μm polystyrene particles have fXO values from MyDEP of 425.02 and 275.37 kHz, respectively. Fibroblast cells were also subjected to numerical analysis because the interaction of keratinocytes and fibroblast cells is essential for wound healing. Consequently, the predicted fXO from the MyDEP plot for keratinocyte and fibroblast cells are 510.53 and 28.10 MHz, respectively. The finite element method (FEM) is utilized to compute the electric field intensity and particle trajectory based on DEP and drag forces. Moreover, the particle trajectories are quantified in a high and low conductive medium. To justify the simulation, further DEP experiments are carried out by applying a non-uniform electric field to a mixture of different sizes of polystyrene particles and keratinocyte cells, and these results are well agreed. The alive keratinocyte cells exhibit NDEP force in a highly conductive medium from 100 kHz to 25 MHz. 2D/3D motion analysis software (DIPP-MotionV) can also perform image analysis of keratinocyte cells and evaluate the average speed, acceleration, and trajectory position. The resultant NDEP force can align the keratinocyte cells in the wound site upon suitable applied frequency. Thus, MyDEP estimates the Clausius-Mossotti factors (CMF), FEM computes the cell trajectory, and the experimental results of prototypic polystyrene particles are well correlated and provide an optimistic response towards keratinocyte cells for rapid wound healing applications.
Nanostructured metal oxide semiconductors have emerged as promising nanoscale photocatalysts due to their excellent photosensitivity, chemical stability, non-toxicity, and biocompatibility. Enhancing the photocatalytic activity of metal oxide is critical in improving their efficiency in radical ion production upon optical exposure for various applications. Therefore, this review paper provides an in-depth analysis of the photocatalytic activity of nanostructured metal oxides, including the photocatalytic mechanism, factors affecting the photocatalytic efficiency, and approaches taken to boost the photocatalytic performance through structure or material modifications. This paper also highlights an overview of the recent applications and discusses the recent advancement of ZnO-based nanocomposite as a promising photocatalytic material for environmental remediation, energy conversion, and biomedical applications.