Sol-gel barium titanate (BaTiO3) and erbium doped barium titanate (Er-BaTiO3) were deposited on SiO2/Si substrates. The phase and crystallinity of the thin films were identified using x-ray diffractometer (XRD). The effect of Er dopant into BaTiO3 thin film on its grain size and surface roughness was studied using atomic force microscope (AFM) in tapping mode. XRD patterns revealed that the films were crystallized with perovskite structure. At the same time, it was shown that introducing Er dopant into BaTiO3 thin film caused the dominant peak to shift towards higher angle. AFM micrographs indicated that the films had well distributed grains, dense and crack-free surface. In general, substitution of Er dopant into Ba-site reduced the grain sizes and roughness parameter of the BaTiO3 which was attributed to the smaller ionic radius of Er.
In previous work we investigated the real-time radioluminescence (RL) yield of Ge-doped silica fibres and Al2O3 nanodot media, sensing electron- and x-ray energies and intensities at values familiarly obtained in external beam radiotherapy. The observation of an appreciable low-dose sensitivity has given rise to the realisation that there is strong potential for use of RL dosimetry in diagnostic radiology. Herein use has been made of P-doped silica optical fibre, 2 mm diameter, also including a 271 µm cylindrical doped core. With developing needs for versatile x-ray imaging dosimetry, preliminary investigations have been made covering the range of diagnostic x-ray tube potentials 30 kVp to 120 kVp, demonstrating linearity of RL with kVp as well as in terms of the current-time (mAs) product. RL yields also accord with the inverse-square law. Given typical radiographic-examination exposure durations from tens- to a few hundred milliseconds, particular value is found in the ability to record the influence of x-ray generator performance on the growth and decay of beam intensity, from initiation to termination.
The importance of the performance of concrete cannot be neglected since it is the early indicator of its physical and mechanical properties. It became more important when material with different physical properties than normal material such as rubber tire was used as concrete constituent. This paper presented apart of research result conducted on mortar and concrete with crumb rubber. Crumb rubber was replaced at 10%, 15% and 20% as sand replacement by volume. In addition, ordinary Portland cement was added to silica fume at 10% and 15% by weight. The properties measured in this study are air content and workability test. As for workability, superplasticizers were constantly used at 1% dosage for all mortar mixture, and 0.5% to 0.7% for concrete mixture. The air content was set at 4% to 6% and mortar flow test was conducted on a steel plate, shocked 15 times in 15 seconds and concrete slump test was carried out using slump cone equipment. Pressure method was used to measure air content. All mixes were done in a controlled room temperature. Results showed that when CR was added in the mixture segregation was observed in mortar requiring a high dose of superplasticizer to be added to improve the workability while air-modifying agent was used to reduce the mortar air content. In concrete mixture, low dosage of superplasticizers was required for workability and air-entrained agent was injected into the mixture to increase the air content between 4%-6%.
The aluminium-silicon (Al-Si) based on Metal Matrix Composites (MMCs) is widely used in lightweight
constructions and transport applications requiring a combination of high strength and ductility. A grain
refinement plays a crucial role in improving characteristics and properties of Al alloys. In this investigation,
titanium diboride (TiB2) and scandium (Sc) inoculants were added to the Al-Si alloys for grain refinement of
an alloy. In this investigation, the corrosion resistance rate of Al-Si cast alloy reinforced by TiB2 and Sc were
measured by potentiostat (AUTOLAB) instrument. The aim of this research is to investigate the corrosion
rate for Al-Si-TiB2-Sc composites that immersed in different concentration of acidic solutions. Besides, the
immersion time of acidic solutions also was investigated. All the samples were prepared accordingly for
ASTM standard by the composition of 6.0 wt% TiB2 and 0.6wt% Sc. All the samples undergo cold mounting
technique for easy handling on corrosion tests. Then the samples were immersed in two different
concentrations acidic medium solutions, which were 0.1.and 1.0 M hydrochloric acids (HCl). The corrosion
rate also was investigated for immersion samples of 1.0 M HCl for 21 days. From the results obtained, added
TiB2 and Sc onto Al-Si alloy gave the better properties in corrosion resistance. Corrosion rates to reduce when
the samples were immersed in a lower concentration of acidic medium, 0.1 HCl. However, there are some
significant on the result but it still following the corrosion rates trend. Thus, improvements to reinforcement
content need to be done in further research to cover the lack of this corrosion rates trend.
Previous studies on screening of lignin-degrading bacteria mainly focused on the ligninolytic ability of the isolated bacteria for the utilization of lignin monomers. In this study, we focused on the depolymerization of alkali lignin to prove the ability of the isolated thermophilic bacterial strains to utilize and depolymerize more than a monomer of alkali lignin within 7 days of incubation. Indigenous thermophilic bacterial isolates from the palm oil plantation were used to evaluate the depolymerization and utilization of alkali lignin. The confirmation of the bacterium-mediated depolymerization of oil palm empty fruit bunch was achieved through the removal of silica bodies, as observed with scanning electron microscopy. Stenotrophomonas sp. S2 and Bacillus subtilis S11Y were able to reduce approximately 50% and 20% of alkali lignin at 7 days of incubation without the requirement for additional carbon sources.
The massive growth of construction industry especially in the developing countries results in extensive quarrying activities which ultimately would lead to the depletion of natural resources. Apart from extensive extraction of the natural granite from the earth for concrete production, marble production industry is also majorly contributing to the quarrying activities. In addition, high volume of waste is generated by the marble production industry as 70% of marble is wasted during the production such as quarrying, cutting, processing and others which is environmental unfriendly. In a way to achieve sustainable construction, the present study is to utilise the waste marble in replacing the coarse aggregate in concrete production. The engineering performance including workability, compressive strength, ultrasonic pulse velocity (UPV) and chloride penetration were analysed. The raw waste marble obtained from the industry were crushed and sieved into maximum size 20 mm and used to replace the coarse aggregate at the level of 20%, 40%, 60%, 80% and 100% respectively. Results show that 60% of the replacement level has yield to optimum result by achieving the highest compressive strength and UPV at approximate 5% higher than the control. Meanwhile, the effect on chloride penetration resistance is more significant, i.e. approximate 19% better than the control. However, increasing the replacement level of waste marble has no significant effect on workability, although an increasing trend was observed.
The growth and the survival of the human malaria parasite Plasmodium falciparum are critically dependent on the functions of the two organelles - the mitochondrion and the apicoplast. However, these two organelles have been known to be difficult to separate from each other when they are released from Plasmodium cell. We have been searching for the conditions with which separation of the mitochondrion and the apicoplast is achieved. In this study, we investigated how the two organelle's separation is affected when the pressure of the nitrogen gas to disrupt the Plasmodium cells by nitrogen cavitation method is lowered from the pressure regularly applied (1200 psi). The parasite cell was sufficiently disrupted even when nitrogen cavitation was carried out at 300 psi. The obtained mitochondrial sample was much less contaminated by DNA compared with the sample prepared using the gas at the regular pressure. After the fractionation by Percoll density gradient, the mitochondrion and the apicoplast from the 300 psi cell lysate exhibited different separation profiles. This is the first experimental evidence that indicates the mitochondrion and the apicoplast of P. falciparum are separable from each other.
Gallium Nitride (GaN) is considered as the second most popular semiconductor material in industry after silicon. This is due to its wide applications encompassing Light Emitting Diode (LED) and power electronics. In addition, its piezoelectric properties are fascinating to be explored as electromechanical material for the development of diverse microelectromechanical systems (MEMS) application. In this article, we conducted a theoretical study concerning surface mode propagation, especially Rayleigh and Sezawa mode in the layered GaN/sapphire structure with the presence of various guiding layers. It is demonstrated that the increase in thickness of guiding layer will decrease the phase velocities of surface mode depending on the material properties of the layer. In addition, the Q-factor value indicating the resonance properties of surface mode appeared to be affected with the presence of fluid domain, particularly in the Rayleigh mode. Meanwhile, the peak for Sezawa mode shows the highest Q factor and is not altered by the presence of fluid. Based on these theoretical results using the finite element method, it could contribute to the development of a GaN-based device to generate surface acoustic wave, especially in Sezawa mode which could be useful in acoustophoresis, lab on-chip and microfluidics applications.
Highly weathered basaltic rock was exposed at PSK profile of Kuantan, Segamat Highway. The weathering profile from fresh rock soil can be observed at PKJ profile at Kg. Jabi Quarry. Twelve rock and soil samples from PSK profile and thirteen samples from PKJ profile have been collected for geochemical analysis. The objective of the analysis is to establish the behaviour of several major and trace elements in the weathering profile of the basaltic rock. The samples were analysed by XRF and XRD techniques. Petrographic study was done on fresh rock samples and concretions. The concentration of major elements (TiO2, Al2O3 and Fe2O3) appear to be increased with the increasing of the degree of weathering whereas the concentration of SiO2 and CaO are decreased. There is a clear correlation between Fe2O3 + Al2O3 with L.O.I as well as between Fe2O3 with Al2O3. Behaviour of the trace elements (Ni, Co, Cr and Zn) against the weathering process are totally different. The secondary minerals (kaolinite, nactire, geothite, hematite and gibbsite) appear to control the behaviour of the major and trace elements.
Batuan basalt yang terluluhawa sepenuhnya telah dicerap di lokaliti PSK Lebuhraya Segamat-Kuantan. Profil luluhawa yang boleh dilihat perubahan daripada batuan segar hingga tanih didapati di lokaliti PKJ Kuari Kg. Jabi. Dua contoh profil dengan masing-masing 12 sampel dan 13 sample tanih telah dikaji untuk menentukan perlakuan beberapa unsur major dan unsur surih batuan basalt yang terluluhawa. Kaedah analisis yang digunakan ialah pendarflour sinar-X (XRF) dan pembelauan sinar-X (XRF). Kajian petrografi pula dibuat pada sampel batuan segar dan sampel konkresi. Nilai unsur major TiO2, Al2O3 dan Fe2O3 bertambah dengan bertambahnya darjah luluhawa manakala SiO2 dan CaO menyusut. Hubungan korelasi Fe2O3 + Al2O3 dengan L.O.I dan Fe2O3 denagn Al2O3 adalah jelas. Unsur surih nikel (Ni) kobalt (Co), kromium (Cr) dan zink (Zn) mempunyai perlakuan yang berbeza-beza dengan luluhawa. Perlakuan yang ditunjukkan oleh unsur major dan surih tersebut dikawal oleh mineral sekunder (koalinit, nakrit, geotit, hematit dan gibsit).
A survey to characterize seismic and ultrasonic properties of a granite weathering profile have been carried out at a roadcut slope exposure along Kuala Lumpur-Karak highway at kilometres 39.9. The terraced cut slope shows a complete weathering profile beginning from fresh grade I rock to grade VI residual soil. Together with in situ seismic measurement, rock samples have been collected for ultrasonic tests in laboratory. The range of velocities representing grades and indices of weathered rocks and soils are determined from the in situ seismic surveys. The range of ultrasonic velocities and elastic moduli are obtained from the laboratory measurements.
Satu survei untuk mencirikan sifat seismos dan ultrasonik profil luluhawa granit telah dilakukan di singkapan potongan jalan, cerun utara lebuhraya Kuala Lumpur-Karak pada lokaliti 39.9 km. Potongan berteres ini mempamirkan satu profil luluhawa lengkap iaitu mulai batuan gred 1 yang segar hingga ke tanah baki bergred VI. Di samping pengukuran seismos secara in situ, sampel batuan juga diambil untuk dibuat pengukuran halaju ultrasonik di makmal. Julat halaju yang mewakili gred dan indeks luluhawa bagi tanah dan batuan diperolehi daripada survei seismos in situ. Julat halaju trasonik dan modulus kenyal diperolehi hasil pengukuran di makmal.
We report here the fabrication of microgaps electrodes on amorphous silicon using low cost techniques such as vacuum deposition and conventional lithography. Amorphous silicon is a low cost material and has desirable properties for semiconductor applications. Microgap electrodes have important applications in power saving devices, electrochemical sensors and dielectric detections of biomolecules. Physical characterization by scanning electron microscopy (SEM) demonstrated such microgap electrodes could be produced with high reproducibility and precision. Preliminary electrical
characterizations showed such structures are able to maintain a good capacitance parameters and constant current supply over a wide ranging differences in voltages. They have also good efficiency of power consumption with high insulation properties.
Atomic force microscopy (AFM) lithography was applied to produce nanoscale pattern for silicon nanowire transistor fabrication. This technique takes advantage of imaging facility of AFM and the ability of probe movement controlling over the sample surface to create nanopatterns. A conductive AFM tip was used to grow the silicon oxide nanopatterns on silicon on insulator (SOI) wafer. The applied tip-sample voltage and writing speed were well controlled in order to form pre-designed silicon oxide nanowire transistor structures. The effect of tetra methyl ammonium hydroxide (TMAH) etching duration on the oxide covered silicon nanowire transistor structure has been investigated. A completed silicon nanowire transistor was obtained by removing the oxide layer via hydrofluoric acid etching process. The fabricated silicon nanowire transistor consists of a silicon nanowire that acts as a channel with source and drain pads. A lateral gate pad with a nanowire head was fabricated very close to the channel in the formation of transistor structures.
This study aimed to document the fish diversity and water quality at Semariang mangrove area, Kuching, Sarawak, which is located at the eastern part of Kuching Wetland National Park. Field samplings were carried out in 2009 during the construction of the flood mitigation channel at the eastern part of the park. A total of 21 families represented by 37 species of fish were caught from the area. The six dominant families in terms of the number of individuals caught were Mugilidae (16%), Leiognathidae (16%), Ambassidae (11%), Ariidae (9%), Lutjanidae (8%) and Plotosidae (6%). In terms of the percentage of six dominant genera based on the number of individuals caught, 16% was represented by Valamugil, 11% by Ambassis, 10% by Gazza, 9% by Arius, 8% by Lutjanus and 6% by Plotosus. The values of diversity and richness indices were lower at stations located close to the flood mitigation channel. Similarly, the concentrations of dissolved oxygen were lower and total suspended solids were significantly higher at stations close to the channel and sand mining area. Therefore, fish fauna and water quality at Semariang mangrove area were affected during the construction of the flood mitigation channel.
The effects of rf power on the structural properties of hydrogenated nanocrystalline silicon (nc-Si:H) thin films deposited using layer-by-layer (LbL) deposition technique in a home-built plasma enhanced chemical vapor deposition (PECVD) system were investigated. The properties of the films were characterized by X-ray diffraction (XRD), microRaman scattering spectroscopy, high resolution transmission electron microscope (HRTEM) and Fourier transform infrared (FTIR) spectroscopy. The results showed that the films consisted of different size of Si crystallites embedded within an amorphous matrix and the growth of these crystallites was suppressed at higher rf powers. The crystalline volume fraction of the films was optimum at the rf power of 60 W and contained both small and big crystallites
with diameters of 3.7 nm and 120 nm, respectively. The hydrogen content increased with increasing rf power and enhanced the structural disorder of the amorphous matrix thus decreasing the crystalline volume fraction of the films. Correlation of crystalline volume fraction, hydrogen content and structure disorder of the films under the effect of rf
power is discussed.
Many techniques have been applied to fabricate nanostructures via top-down approach such as electron beam lithography. However, most of the techniques are very complicated and involves many process steps, high cost operation as well as the use of hazardous chemicals. Meanwhile, atomic force microscopy (AFM) lithography is a simple technique which is considered maskless and involves only an average cost and less complexity. In AFM lithography, the movement of a probe tip can be controlled to create nanoscale patterns on sample surface. For silicon nanowire (SiNW) fabrication, a conductive tip was operated in non-contact AFM mode to grow nanoscale oxide patterns on silicon-on-insulator (SOI) wafer surface based on local anodic oxidation (LAO) mechanism. The patterned structure was etched through two steps of wet etching processes. First, the TMAH was used as the etchant solution for Si removing. In the second step, diluted HF was used to remove oxide mask in order to produce a completed SiNW based devices. A SiNW based device which is formed by a nanowire channel, source and drain pads with lateral gate structures can be fabricated by well controlling the lithography process (applied tip voltage and writing speed) as well as the etching processes.
Cupric oxide (CuO) thin films were prepared on a glass and silicon (Si) substrates by radio frequency magnetron sputtering system. The structural, optical and electrical properties of CuO films were characterized by X-ray diffraction (xRD), atomic force microscopy (AFM), Fourier transform infrared spectrometer, ultra-violet visible spectrophotometer, respectively, four point probe techniques and Keithley 4200 semiconductor characterization system. The xRD result showed that single phase CuO thin films with monoclinic structure were obtained. AFM showed well organized nano-pillar morphology with root mean square surface roughness for CuO thin films on glass and Si substrates were 3.64 and 1.91 nm, respectively. Infrared reflectance spectra shown a single reflection peak which is corresponding to CuO optical phonon mode and it confirmed that only existence of CuO composition on both substrates. The optical direct band gap energy of the CuO film grown on glass substrate, which is calculated from the optical transmission measurement was 1.37 eV. Finally, it was found that the deposited CuO films are resistive and the palladium formed ohmic contact for CuO on glass and schottky contact for CuO on Si.
In this work, the structural properties of radio frequency sputtering-grown zinc oxide (ZnO) thin films on sapphire (Al203), gallium arsenide (GaAs) and n-type silicon (Si) substrates were characterized. Scanning electron microscopy was employed to study the surface morphology of the samples. X-ray diffraction (xRD) measurements were also performed to obtain the structural information of the samples. The xRD results showed that the ZnO layers grown on different substrates have similar lattice constant (c) values, which were used to calculate the strain percentages of the ZnO thin films. The surface morphologies of the ZnO thin films indicated the formation of a granular surface when ZnO is deposited on n-type Si(100) and Si( 111 ) substrates. Meanwhile, a leaf-like surface is obtained when ZnO is deposited on GaAs and Al203 substrates. The results showed that the ZnO thin film grown on n-type Si(100) has the best quality among all the samples.
The presence of pores plays an important role for many membrane processes especially in ultrafiltration and microfiltration. Epoxidised natural rubber (ENR)/polyvinyl chloride (PVC) membranes filled with two types of silica fillers were prepared via simultaneous solvent exchange and evaporation of solvent technique. Two types of silica, i.e. microsilica (microcrystalline
silica powder) and nanosilica (generated from tetraethoxysilane (TEOS)) were used. The chemical composition, morphology and mechanical stability of the membranes were studied. Both types of silica showed good interaction with the membrane matrix. The formation of pores depended on the size of silica particles added. Microsilica produced large pores while insitu generated nanosilica produced nanosized pores. The mechanical properties of membrane improved with the addition
of silica. The tensile strength increased from 10.6 MPa to 17.8 MPa and 14.5 MPa for nanosilica and microsilica filled membrane while the tensile modulus increased from 1.6 MPa to 3.8 MPa and 3.4 MPa, respectively. Thus, both types of silica acted as a filler as well as pore forming agent for the ENR/PVC membrane.
A significant source of microplastics is from the usage of microbeads in the market since petrochemical plastic bead is a material used in cosmetic scrubs. A possible way to counteract the problem is by the substitution of synthetic plastic to natural biodegradable polymer. Polyhydroxyalkanoate (PHA) is a general class of thermoplastic microbial polymer and it is the best alternative to some petrochemical plastics due to its biodegradability. Some PHA has earned its way into cosmetic application due to its biocompatibility. This data article reports data on the development of biodegradable microbeads by using the double emulsion solvent evaporation technique. Our data describe the extraction of biopolymer from marine bacteria that was cultivated in shaken flask culture, removal of endotoxins using oxidizing agent, the production of microbeads using a peristaltic pump with a specific flowrate and silicon tubing, and the cytotoxicity of the microbeads.
Catalytic esterification of glycerol with oleic acid (OA) was optimized over hydrophobic mesoporous zirconia-silica heterogeneous acid catalyst (ZrO2-SiO2-Me&Et-PhSO3H) and benchmarked with commercial catalysts (Aquivion and Amberlyst 15) in order to examine the effect of catalyst acidity on conversion, yield and product selectivity. The process optimisation results showed an 80% conversion with a 59.4% glycerol mono-oleate (GMO) and 34.6% glycerol dioleate (GDO) selectivities corresponding to a combined GMO and GDO selectivity of 94.8% at equimolar OA-to-glycerol ratio, 160°C reaction temperature, 5 wt% catalyst concentration with respect to the OA weight and 4 h reaction time. This work reveals that the hydrophobic and mild acidic ZrO2-SiO2-Me&Et-PhSO3H catalyst outperformed Amberlyst 15 and Aquivion with a yield of 82% and GMO selectivity of 60%. It is found that catalyst acidity is a key parameter for catalytic activity and conversion rate. Nevertheless, high acidity/acid strength reduced the product yield in the glycerol esterification of OA.