In municipal solid waste (MSW) landfills, biodegradation of the organic MSW fraction results in elevated waste and basal liner temperatures which have the potential to cause the clay component of the basal liner to experience severe moisture loss over time and eventually undergo desiccation cracking. Cracking of the basal liner's clay component would result in an uncontrolled release of contaminants into the surrounding environment and ultimately give rise to a variety of major environmental concerns. Accordingly, this study examined the variation of temperature-moisture profiles along the depth of a compacted clay liner (CCL) exposed to different constant elevated waste temperatures (CETs) in the absence and presence of two heat reduction techniques, respectively. Rockwool insulation layers with varying thicknesses and galvanized steel cooling pipes with varying flowrates were introduced separately as the two heat reduction techniques. Introduction of both techniques led to a significant attenuation of the temperature rise and desiccation experienced by the CCL in the face of different CETs. An increase in rockwool thickness increments led to a progressive reduction of CCL temperature, while an increase in flow rate under turbulent condition did not have a significant influence on the temperature and desiccation reduction of the CCL. Nevertheless, the present study certainly highlights the potential of the two proposed heat reduction techniques to minimize desiccation and consequently increase the service life of CCLs exposed to different elevated temperatures in MSW landfills.
In recent years, closed-cell porous Aluminum (Al) has drawn increasing attention, particularly in the applications requiring reduced weight and energy absorption capability such as in the automotive and aerospace industries. In the present work, porous Al with closed-cell structure was successfully fabricated by powder metallurgy technique using PMMA as a space holder. The effects of the amount of PMMA powder on the porosity, density, microstructure and compressive behaviors of the porous specimens were systematically evaluated. The results showed that closed-cell porous Al having different porosities (12%-32%) and densities (1.6478 g/cm³, 1.5125 g/cm³ and 1.305 g/cm³) could be produced by varying the amount of PMMA (20-30 wt %). Meanwhile, the compressive behavior results demonstrated that the plateau stress decreased and the energy absorption capacity increased with increasing amount of PMMA. However, the maximum energy absorption capacity was achieved in the closed-cell porous Al with the addition of 25 wt % PMMA. Therefore, fabrication of closed-cell porous Al using 25 wt % PMMA is considered as the optimal condition in the present study since the resultant closed-cell porous Al possessed good combinations of porosity, density and plateau stress, as well as energy absorption capacity.
The nanomechanical properties of carbon nanotubes particulate-reinforced aluminum matrix nanocomposites (Al-CNTs) have been characterized using nanoindentation. Bulk nanocomposite specimens containing 2 wt % multiwalled CNTs (MWCNTs) were synthesized by a combination of ball milling and powder metallurgy route. It has been tried to understand the correlation between microstructural evolution particularly carbon nanotubes (CNTs) dispersion during milling and mechanical properties of Al-2 wt % nanocomposites. Maximum enhancement of +23% and +44% has been found in Young's modulus and hardness respectively, owing to well homogenous dispersion of CNTs within the aluminum matrix at longer milling time.
We demonstrate efficient semipolar (11-22) 550 nm yellow/green InGaN light-emitting diodes (LEDs) with In0.03Ga0.97N barriers on low defect density (11-22) GaN/patterned sapphire templates. The In0.03Ga0.97N barriers were clearly identified, and no InGaN clusters were observed by atom probe tomography measurements. The semipolar (11-22) 550 nm InGaN LEDs (0.1 mm2 size) show an output power of 2.4 mW at 100 mA and a peak external quantum efficiency of 1.3% with a low efficiency drop. In addition, the LEDs exhibit a small blue-shift of only 11 nm as injection current increases from 5 to 100 mA. These results suggest the potential to produce high efficiency semipolar InGaN LEDs with long emission wavelength on large-area sapphire substrates with economical feasibility.
A new contactless technique for latent fingerprint visualization on nonporous curved surfaces of circular cross section was introduced by Low et al. (1). The technique utilizes a plane mirror to convey the light rays toward the inspected surfaces for latent fingerprint visualization. This research activity came up as an extension of the previous study which utilized an aluminum plate as the plane mirror to illuminate the inspected surfaces. Dulling spray was used to increase the diffuse component of the reflective aluminum plate. However, the amount of dulling spray will affect the uniformity of the illumination on the inspected curved surfaces. In this study, a study on the new materials for the plane mirror was carried out. Coated aluminum, opal, and ground glass diffusers were selected as the new materials. The performance of the new materials was compared to the aluminum based on the quality of the captured images on various nonporous cylindrical surfaces. A statistical approach known as randomized complete block design was used to design the experiment. The quality of the captured images was obtained using Spectral Image Validation and Verification. Two-way analysis of variance and Fisher's least significant difference test were used to analyze the quality of the images. From the results of the statistical analysis, coated aluminum has the best performance compared to aluminum, opal, and ground glass diffusers.
Carbon nanotube reinforced aluminium matrix composites (Al-CNTs) have been widely used in aerospace and automotive industries where high quality and strength is required. The enhanced mechanical properties of Al-CNTs are closely related to processing technique due to challenges within production of these composite materials. In the current review, solid state processing techniques used for synthesizing Al-CNTs have been reviewed to provide an insight into the features and capabilities of each technique regarding the incorporation of CNT reinforcements. To conclude, the mechanical performance of Al-CNT composites is mainly decided by the capability of each technique in the dispersion of CNTs within the aluminum matrix.
Efforts to reduce manufacturing cost and negative environmental impacts have seen the mixture of natural fibre with synthetic fibre in composite structures. However, there are limited studies on the notch effect and fibre orientation on mechanical properties of hybrid fibre metal laminate (FML). In this study, tensile properties of FML with notch and different fibre orientation were investigated. The hybrid FML incorporated with kenaf fibre at the middle layer was compared with FML with three layers of E-glass fibre. Kenaf fibre and E-glass fibre used were in plain woven form. The FML in 2/1 configuration was manufactured through hot press manufacturing method to bond layers of annealed aluminium 5052 to the composite. Tensile test was conducted in a quasi-static manner according to ASTM E8. The results showed FML with three layers of glass fibre exhibited higher tensile strength compared with hybrid FML. However, the introduction of kenaf fibre in hybrid FML reduces the notch and fibre orientation sensitivity compared with glass fibre reinforced FML.
Ahmad Fuad Ab Ghani, Mohamad Kamarul Anwar Sahar, Muhammad Ridzuan Husyairi Azmi, Nurul Izzati Medon, Muhammad Syazwan Samsuri, Muhammad Syurabil Abdani
There are several types of grating, such as platform, bridge decks and filters. In design process, there
are several important terms that have to be prioritised; engineering design, strength to weight ratio, cost,
maintainability, reparability etcetera. Advanced materials, such as composite materials offer great
strength to weight ratio and high mechanical properties for grating fabrication. Furthermore the
reparability and maintenance problems could be solved as it is anti corrosion and the long service life
attribute of composite makes it a great design material for replacement of conventional steel or
aluminium. Bio composites, such as bamboo and coir fiber yield advantage in terms of less cost and
abundance availability compared to commercial unidirectional composite materials, such as glass fiber
reinforced polymer (GFRP) and carbon fiber reinforced polymer (CFRP) which is considerably
expensive yet possess higher mechanical properties. This papers presents a conceptual design of
grating design utilizing bamboo composite as material. Pugh method has been chosen as design criteria
selection matrix in finalizing the design of industrial grating for scaffolding (Pugh, 1991).
The whole Bachok area is covered by alluvial deposit. The alluvium has three aquifers at depth of 0 - 5, 15 - 30 and 40 - 60 meters below surface. Preliminary geophysical surveys including seismic refraction, reflection and resistivity techniques have been carried out to investigate thickness and depth of the aquifers, depth of bedrock and the salinity of the underground water. Results show that the position of first aquifer has been well determined by seismic refraction technique. Whereas the details of deeper aquifers and the bedrock have been determined by seismic reflection techniques. Geoelectrical resistivity low obtained for the first aquifer suggest that it could be due to either salt water intrusion or the presence of marine clay.
Keseluruhan kawasan Bachok merupakan endapan aluvium. Endapan ini mempunyai tiga akuifer pada kedalaman 0 - 5 meter, 15 - 30 meter dan 40 - 60 meter. Kajian geofizik pada tahap awal yang merangkumi aspek seismos biasan, seismos pantulan dan kerintangan geoelektrik telah dilakukan untuk menyiasat ketebalan dan kedalaman akuifer, kedalaman batu dasar dan kemasinan air tanah. Hasil kajian menunjukkan bahawa teknik seismos biasan telah dapat menghasilkan maklumat mengenai kedudukan akuifer pertama. manakala teknik seismos pantulan menghasilkan maklumat terperinci mengenai akuifer kedua dan ketiga serta batu dasar. Nilai kerintangan geoelektrik rendah bagi akuifer pertama menunjukkan sama ada disebabkan oleh intrusi air masin atau kehadiran lempung samudera.
The sorption parameters of two heavy metals (i.e. Pb and Cu) in clay soils from Selangor were studied using batch equilibrium test. The test was conducted in two separate systems, i.e. single and mix solutions. The sorption isotherms data from this test were then used to calculate the sorption parameters, i.e. distribution coefficient (Kd) and maximum adsorption capacity (Am). Langmuir sorption equation was used to model the sorption data with the correlation coefficients (r2) higher than 0.6. The study has revealed that different soils have different sorption capacity for different heavy metals. The Kd values are proportional to the sorption capacity of the soils. The sorption of Pb and Cu in single solution is higher than in mix solution, due to the competition for sorption sites among heavy metals in mix solution. The Kd values for Pb in single solution ranging from 36.18-334.48 L/g and for Cu is 9.29-66.19 L/g. In mix solution, the Kd values for Pb and Cu are much smaller, ranging from 23.13-31.79 L/g and 3.95-18.53 L/g respectively. The Am values in single solution for both Pb and Cu are ranging from 0.48-1.09 mg/g dan 0.18-0.70 mg/g respectively. While in mix solution, the values of Am for Pb ranging from 0.20-1.11 mg/g and Cu within 0.18-0.60 mg/g.
Kajian kepekatan logam dalam air di Tasik Bukit Merah telah dijalankan pada April 2009. Lima belas stesen persampelan telah dipilih dan sampel air permukaan bagi penentuan logam telah diambil. Beberapa parameter kualiti air seperti suhu, konduktiviti, oksigen terlarut, pH dan keliatan air telah ditentukan di setiap stesen. Sebanyak 11 jenis logam iaitu kadmium, zink, plumbum, kuprum, nikel, ferum, kobalt, aluminium, barium, kromium dan mangan (Mn) telah ditentukan dalam sampel air. Keputusan menunjukkan kepekatan semua logam kajian berada di bawah kepekatan maksimum yang dicadangkan oleh piawaian Malaysia dan antarabangsa bagi melindungi hidupan akuatik kecuali bagi logam Fe dan Al. Bagi parameter kualiti air, kajian menunjukkan semua parameter berada dalam julat kepekatan semula jadi (kelas I) berdasarkan Piawaian Kualiti Air Kebangsaan (NWQS Malaysia) kecuali oksigen terlarut dan pH di beberapa stesen persampelan terutama di bahagian timur tasik yang didapati dipengaruhi oleh faktor-faktor semula jadi dan antropogenik.
The formation of nano pores on aluminum at 30oC- 38oC, employing a one step anodization technique which does not require removing the oxide layer formed is presented. A 20% phosphoric acid electrolyte (concentration higher than the normal anodization concentration of 5 to 10%) at a cell potential of 60 volts was used. A platinum electrode was used as the cathode electrode while the aluminum substrate as the anode electrode. A dc powered electrochemical cell to provide the required amount of current density (without the use of temperature controlled water bath) suitable or necessary for pore formation at room temperature was employed. The results obtained show that pore formation at room temperature is achievable and the pore diameter ranged between 80-120 nm.
The effect of TiO₂ nanoparticle (NP) content on the improvement of poly(9,9'-di-n-octylfluorenyl-2,7-diyl) (PFO)/Fluorol 7GA organic light emitting diode (OLED) performance is demonstrated here. The PFO/Fluorol 7GA blend with specific ratios of TiO₂ NPs was prepared via a solution blending method before being spin-coated onto an indium tin oxide (ITO) substrate to act as an emissive layer in OLEDs. A thin aluminum layer as top electrode was deposited onto the emissive layer using the electron beam chamber. Improvement electron injection from the cathode was achieved upon incorporation of TiO₂ NPs into the PFO/Fluorol 7GA blend, thus producing devices with intense luminance and lower turn-on voltage. The ITO/(PFO/Fluorol 7GA/TiO₂)/Al OLED device exhibited maximum electroluminescence intensity and luminance at 25 wt % of TiO₂ NPs, while maximum luminance efficiency was achieved with 15 wt % TiO₂ NP content. In addition, this work proved that the performance of the devices was strongly affected by the surface morphology, which in turn depended on the TiO₂ NP content.
This paper investigates the compressibility characteristics of compacted clay treated with cement, peat ash and silica
sand. For this purpose, one dimensional consolidation tests were conducted to determine the soil consolidation properties.
The test specimens were trimmed from the compaction test specimen. The 1D consolidation test specimen was subjected
to the normal pressures of 2.5, 5, 10, 20, 40, 80 and 160 kPa in sequence on the test specimen which was saturated with
distilled water. At the end of the loading period of 80 kPa, the vertical load was removed and the specimen was allowed
to expand for 24 h for the purpose of evaluating of its swelling behavior. The results showed that void ratio of the soil
specimens decreased with increasing effective normal pressure. The laboratory investigation clearly demonstrates that,
settlement is as the compression of a soil specimen due to vertical loading applied at the top surface of the 1D consolidation
test specimen. It was concluded that, the compression settlement of the stabilized soil with the binder composition of
18% cement, 2% peat ash and 5% silica sand improved by almost 1.3-fold. A notable discovery is the suitability of the
stabilized soil for road embankment and low lying marginal area for foundation works; also solving the environmental
problems in relation to peaty ground. However, sufficient laboratory and field testing are required.
Ground improvement using artificial crust composite foundation, consisting of stabilization of soft clay and composite foundation, is an effective technique for the treatment of deep soft soil layers under infrastructure embankments. In this study, the load responses and settlement performance of this improvement technique were investigated using two centrifuge model tests to compare the variations of the vertical deformation, pore water pressure, axial force of the piles and tensile stress at the bottom of the artificial crust in the crust composite foundation with those in pile-supported embankment. The results of centrifuge model tests showed that the load responses and settlement performance of artificial crust composite foundation was different from the pile-supported embankment, which displayed mainly that the final middle settlement of crust composite foundation can be reduced by about 15% compared with those of pile-supported embankment with the same length of pile and construction cost. The deformation of the crust with the characteristics of the plate was found based on the change of the tensile stress. Additionally, the excess pore water pressure in the crust composite foundation was lower owing to the stress diffusion effect of the crust during the loading period and the dissipation rate of excess pore water pressure was slower due to lower permeability of the crust at the same loading period. Eventually, the axial force of the middle piles was reduced. At the same time, the boundary stress was functioned with the crust, the axial force of the side piles was improved. The comparison of measured and calculated results was carried out using the stress reduction ratio, the result shows that the bearing capacity of the subsoil in the crust composite was improved.
It is well-known that the characteristics of hardness and drillability are influenced by microstructure of rock. In this study, rock properties were analyzed on grain size and grain content. Coarse-grain and fine-grain sandstones were tested under successive indentation condition. Eighteen groups of sandstone and shale were employed for the drillability test. Indentation tests results showed that grain size influenced the low point of residual hardness, the crushing depth and volume and grain content influenced the peak point of hardness. The drillability values of shale increased with increasing contents of clay and quartz. Meanwhile, drillability values of sandstone increased with increasing content of quartz, but decreased with increasing content of clay. Therefore, these preliminary studies show great potential applications for selecting suitable bit type and formulating drilling program as a function of rock microstructure and crushing rock method for bit in the oil drilling.
Metallic foams are a new class of materials that have a great potential to be used in various functional and structural applications. Due to their competitive price compared to aluminium, metallic foams are anticipated to become an alternative material for light-weight structures. In this study, stainless steel foams are fabricated using a powder space holder method. The materials used include stainless steel powder, a novel space holder glycine and binders consisting of palm stearin and of polyethylene (PE). The stainless steel foams are sintered at 1100o C, 1200o C and 1300o C with sintering times of 1, 2 and 3 h, respectively, to investigate the effects of the sintering parameters on the compressive yield strength of the stainless steel foams. The results showed that all of the stainless steel foams produced exhibit the general behaviours of metal foams. The sintering time is the most significant parameter that influences the compressive yield strength of stainless steel foams. Increasing the sintering temperature and sintering time will increase the compressive yield strength. The interaction between the sintering temperature and sintering time is found to be not statistically significant.
Zirconia toughened alumina (ZTA) is a promising advanced ceramic material for a wide range of applications that are subjected to dynamic loading. Therefore, the investigation of dynamic compressive strength, fracture toughness and hardness is essential for ZTA ceramics. However, the relationship between these mechanical properties in ZTA has not yet been established. An example of this relationship is demonstrated using ZTA samples added with MgO prepared through conventional sintering. The microstructure and mechanical properties of ZTA composites were characterized. The hardness of ZTA composites increased for ≤0.7 wt.% MgO due to the pinning effect of MgO and decrease of the porosity in the microstructure. Oppositely, the fracture toughness of ZTA composites continuously decreased due to the size reduction of Al2O3 grains. This is the main reason of deteriorate of dynamic compressive strength more than 0.2 wt.% of MgO addition. Therefore, the SHPB test shows the improvement of the dynamic compressive strength only up to a tiny amount (0.2 wt.% of MgO addition) into ZTA ceramics.
This paper elucidates the capability of isolated indigenous bacteria to remove aluminium from wastewater and soil. Two indigenous species of Brochothrix thermosphacta and Vibrio alginolyticus were isolated from an aluminium-contaminated site. These two species were used to treat aluminium-containing wastewater and contaminated soil using the bioaugmentation method. B. thermosphacta showed the highest aluminium removal of 57.87 ± 0.45% while V. alginolyticus can remove aluminium up to 59.72 ± 0.33% from wastewater. For aluminium-contaminated soil, B. thermosphacta and V. alginolyticus, showed a highest removal of only 4.58 ± 0.44% and 5.48 ± 0.58%, respectively. The bioaugmentation method is more suitable to be used to treat aluminium in wastewater compared to contaminated soil. The produced biomass separation after wastewater treatment was so much easier and applicable, compared to the produced biomass handling from contaminated soil treatment. A 48.55 ± 2.45% and 40.12 ± 4.55% of aluminium can be recovered from B. thermosphacta and V. alginolyticus biomass, respectively, with 100 mg/L initial aluminium concentration in wastewater.
Objective: To evaluate the effect of type of viscosity and groove on surface detail reproduction of elastomeric impression materials. Methods: Two polyvinylsiloxane and polyether elastomeric impression materials were investigated. An aluminium cylindrical reference block with V- and U-shaped grooves of 1 mm and 2 mm in depth was machined using CAD-CAM system. Impressions of the block were taken to produce 35 master dies. Each die was immersed in distilled water for 5 minutes prior to impression making. Surface topography of the dies and impressions were captured using Alicona Imaging System. Mean difference in depth between the mas-ter dies and corresponding impressions’ grooves were analyzed. Results: Type of viscosities and groove showed significant main effects on surface detail (p < .01), but no significant interaction was observed between the two (p > .01). Express™ putty/light exhibited the lowest mean difference in depth for all grooves. The highest mean difference for U1 (38.3μm ± 21.55), U2 (52.96μm ± 30.39),V1 (45.02μm ± 34.82) and V2 (58.44μm ± 44.19) was obtained from Impregum medium, Aquasil medium, Impregum™ heavy/light and Impregum™ heavy/light groups respectively. Conclusion: Express putty/light-bodied material produced the best surface detail, and U-shaped groove showed superior detail reproduction.