Displaying publications 61 - 80 of 217 in total

Abstract:
Sort:
  1. Wan Fadhilah Khalik, Ong SA, Wong YS, Nik Athirah Yusoff, Fahmi Ridwan, Ho LN
    Sains Malaysiana, 2015;44:607-612.
    In this study, the photocatalytic degradation of batik wastewater in the presence of zinc oxide (ZnO) as photocatalyst was
    investigated. The effect of various operating parameters, such as pH of batik wastewater, catalyst dosage and aeration
    on the photocatalytic degradation process, was examined. The mineralization of batik wastewater was also evaluated
    through chemical oxygen demand analysis. The decolorization of batik wastewater was enhanced at acidic conditions
    (pH3) which was 88.2% after 10 h irradiated under solar light, meanwhile its mineralization was 286 mg/L after 12 h
    irradiation time. The data obtained for photocatalytic degradation of batik wastewater was well fitted with the LangmuirHinshelwood
    kinetic model. It can be concluded that batik wastewater could be decolorized and mineralized under solar
    light irradiation with presence of ZnO.
    Matched MeSH terms: Zinc Oxide
  2. Tharsika T, Haseeb AS, Akbar SA, Sabri MF, Hoong WY
    Sensors (Basel), 2014;14(8):14586-600.
    PMID: 25116903 DOI: 10.3390/s140814586
    An inexpensive single-step carbon-assisted thermal evaporation method for the growth of SnO2-core/ZnO-shell nanostructures is described, and the ethanol sensing properties are presented. The structure and phases of the grown nanostructures are investigated by field-emission scanning electron microscopy (FESEM), transmission electron microscopy (TEM) and X-ray diffraction (XRD) techniques. XRD analysis indicates that the core-shell nanostructures have good crystallinity. At a lower growth duration of 15 min, only SnO2 nanowires with a rectangular cross-section are observed, while the ZnO shell is observed when the growth time is increased to 30 min. Core-shell hierarchical nanostructures are present for a growth time exceeding 60 min. The growth mechanism for SnO2-core/ZnO-shell nanowires and hierarchical nanostructures are also discussed. The sensitivity of the synthesized SnO2-core/ZnO-shell nanostructures towards ethanol sensing is investigated. Results show that the SnO2-core/ZnO-shell nanostructures deposited at 90 min exhibit enhanced sensitivity to ethanol. The sensitivity of SnO2-core/ZnO-shell nanostructures towards 20 ppm ethanol gas at 400 °C is about ~5-times that of SnO2 nanowires. This improvement in ethanol gas response is attributed to high active sensing sites and the synergistic effect of the encapsulation of SnO2 by ZnO nanostructures.
    Matched MeSH terms: Zinc Oxide/chemistry*
  3. Tapsir Z, Aly Ahmed HM, Luddin N, Husein A
    J Contemp Dent Pract, 2013 Jan 1;14(1):47-50.
    PMID: 23579892
    To evaluate and compare the microleakage of various restorative materials used as coronal barriers between endodontic appointments.
    Matched MeSH terms: Zinc Oxide/chemistry
  4. Baiuitiar Ul Haq, Ahmed R, Shaari A, Afaq A, Hussain R
    Sains Malaysiana, 2014;43:813-817.
    The central theme of nanotechnology to miniaturize devices has stimulated interest in diluted magnetic semiconductors (DMS). DMS that simultaneously exhibit magnetic and semiconducting behavior are capable of parting properties of two different function devices into one. In this research we present our first principles investigations related to the structural and electronic properties of, Cr doped zinc-blende (zB) ZnO, DMS. These calculations are carried out using full potential linearized augmented plane wave plus local orbital (FP-L(APW+lo)) with generalized gradient approximations approach as implemented in WIEN2k code. In this study, the effect of Cr doping on lattice parameters, spin polarized electronic band structure, density of states (Dos) of ZnO is presented and analyzed in detail.
    Matched MeSH terms: Zinc Oxide
  5. Saifullah B, Arulselvan P, El Zowalaty ME, Fakurazi S, Webster TJ, Geilich B, et al.
    ScientificWorldJournal, 2014;2014:401460.
    PMID: 25050392 DOI: 10.1155/2014/401460
    Tuberculosis is a lethal epidemic, difficult to control disease, claiming thousands of lives every year. We have developed a nanodelivery formulation based on para-aminosalicylic acid (PAS) and zinc layered hydroxide using zinc nitrate salt as a precursor. The developed formulation has a fourfold higher efficacy of PAS against mycobacterium tuberculosis with a minimum inhibitory concentration (MIC) found to be at 1.40 μg/mL compared to the free drug PAS with a MIC of 5.0 μg/mL. The newly developed formulation was also found active against Gram-positive bacteria, Gram-negative bacteria, and Candida albicans. The formulation was also found to be biocompatible with human normal lung cells MRC-5 and mouse fibroblast cells-3T3. The in vitro release of PAS from the formulation was found to be sustained in a human body simulated phosphate buffer saline (PBS) solution at pH values of 7.4 and 4.8. Most importantly the nanocomposite prepared using zinc nitrate salt was advantageous in terms of yield and free from toxic zinc oxide contamination and had higher biocompatibility compared to one prepared using a zinc oxide precursor. In summary, these promising in vitro results are highly encouraging for the continued investigation of para-aminosalicylic acid and zinc layered hydroxide nanocomposites in vivo and eventual preclinical studies.
    Matched MeSH terms: Zinc Oxide/chemistry
  6. Gaya UI, Abdullah AH, Zainal Z, Hussein MZ
    J Hazard Mater, 2009 Aug 30;168(1):57-63.
    PMID: 19268454 DOI: 10.1016/j.jhazmat.2009.01.130
    The photocatalytically driven removal of eco-persistent 4-chlorophenol from water using ZnO is reported here. Kinetic dependence of transformation rate on operating variables such as initial 4-chlorophenol concentration and photocatalyst doses was investigated. A complete degradation of 4-chlorophenol at 50 mg L(-1) levels was realised in 3h. Analytical profiles on 4-chlorophenol transformation were consistent with the best-line fit of the pseudo zero-order kinetics. The addition of small amounts of inorganic anions as SO(4)(2-), HPO(4)(-), S(2)O(8)(2-) and Cl(-) revealed two anion types: active site blockers and rate enhancers. Fortunately, Cl(-) and SO(4)(2-) commonly encountered in contaminated waters enhanced the rate of 4-chlorophenol degradation. The reaction intermediates and route to 4-chlorophenol mineralisation were elucidated by combined RP-HPLC and GC-MS methods. In addition to previously reported pathway products of 4-chlorophenol photo-oxidation catechol was detected. A radical mechanism involving o-hydroxylation is proposed to account for the formation of catechol.
    Matched MeSH terms: Zinc Oxide/chemistry*
  7. Le AT, Pung SY, Sreekantan S, Matsuda A, Huynh DP
    Heliyon, 2019 Apr;5(4):e01440.
    PMID: 31008388 DOI: 10.1016/j.heliyon.2019.e01440
    Effluent discharges from industry and domestic waste containing unknown inorganic pollutants. In this work, different mechanisms of heavy metal ions removal using ZnO particles were studied. ZnO particles were synthesized using solid precipitation technique. The morphology of ZnO particles was rod-like shape. The average length and diameter of ZnO particle were 497.34 ± 15.55 and 75.78 ± 10.39nm, respectively. These particles removed effectively heavy metal ions such as Cu(II), Ag(I) and Pb(II) ions with efficiency >85% under exposure of 1 hour of UV light. However, poor removal efficiency, i.e. <15% was observed for Cr(VI), Mn(II), Cd(II) and Ni(II) ions. The removal of these heavy metal ions was in the forms of metals or metal oxide via reduction/oxidation or adsorption mechanism.
    Matched MeSH terms: Zinc Oxide
  8. Azizi S, Ahmad MB, Hussein MZ, Ibrahim NA
    Molecules, 2013 May 28;18(6):6269-80.
    PMID: 23760028 DOI: 10.3390/molecules18066269
    Synthesis of ZnO-Ag heterostructure nanoparticles was carried out by a precipitation method with cellulose nanocrystals (CNCs) as a stabilizer for antimicrobial and thermal studies. ZnO-Ag nanoparticles were obtained from various weight percentages of added AgNO₃ relative to Zn precursors for evaluating the best composition with enhanced functional properties. The ZnO-Ag/CNCs samples were characterized systematically by TEM, XRD, UV, TGA and DTG. From the TEM studies we observed that ZnO-Ag heterostructure nanoparticles have spherical shapes with size diameters in a 9-35 nm range. The antibacterial activities of samples were assessed against the bacterial species Salmonella choleraesuis and Staphylococcus aureus. The CNC-stabilized ZnO-Ag exhibited greater bactericidal activity compared to cellulose-free ZnO-Ag heterostructure nanoparticles of the same particle size. The incorporation of ZnO-Ag hetreostructure nanoparticles significantly increased the thermal stability of cellulose nanocrystals.
    Matched MeSH terms: Zinc Oxide/chemistry*
  9. Ullah S, Zainol I, Idrus RH
    Int J Biol Macromol, 2017 Nov;104(Pt A):1020-1029.
    PMID: 28668615 DOI: 10.1016/j.ijbiomac.2017.06.080
    The zinc oxide nanoparticles (particles size <50nm) incorporated into chitosan-collagen 3D porous scaffolds and investigated the effect of zinc oxide nanoparticles incorporation on microstructure, mechanical properties, biodegradation and cytocompatibility of 3D porous scaffolds. The 0.5%, 1.0%, 2.0% and 4.0% zinc oxide nanoparticles chitosan-collagen 3D porous scaffolds were fabricated via freeze-drying technique. The zinc oxide nanoparticles incorporation effects consisting in chitosan-collagen 3D porous scaffolds were investigated by mechanical and swelling tests, and effect on the morphology of scaffolds examined microscopically. The biodegradation and cytocompatibility tests were used to investigate the effects of zinc oxide nanoparticles incorporation on the ability of scaffolds to use for tissue engineering application. The mean pore size and swelling ratio of scaffolds were decreased upon incorporation of zinc oxide nanoparticles however, the porosity, tensile modulus and biodegradation rate were increased upon incorporation of zinc oxide nanoparticles. In vitro culture of human fibroblasts and keratinocytes showed that the zinc oxide nanoparticles facilitated cell adhesion, proliferation and infiltration of chitosan-collagen 3D porous scaffolds. It was found that the zinc oxide nanoparticles incorporation enhanced porosity, tensile modulus and cytocompatibility of chitosan-collagen 3D porous scaffolds.
    Matched MeSH terms: Zinc Oxide/chemistry*
  10. Ramiah SK, Atta Awad E, Hemly NIM, Ebrahimi M, Joshua O, Jamshed M, et al.
    J Anim Sci, 2020 Oct 01;98(10).
    PMID: 32936879 DOI: 10.1093/jas/skaa300
    This study was conducted to explore the effect of the zinc oxide nanoparticles (ZnONPs) supplement on the regulatory appetite and heat stress (HS) genes in broiler chickens raised under high or normal ambient temperatures. In this study, 240 one-day-old male broiler chicks (Cobb 500) were randomly assigned to 48 battery cages. From day 1, these 48 cages were randomly subjected to four different treatment strategies: Control (wherein, their basal diet included 60 mg/kg of ZnO), ZNONPs 40 (wherein basal diet included 40 mg/kg of ZnONPs), ZnONPs 60 (basal diet included 60 mg/kg of ZnONPs), and ZnONPs 100 (basal diet included 100 mg/kg of ZnONPs). Thereafter, from day 22 to 42, the chickens from each dietary treatment group were subjected to different temperature stresses either normal (23 ± 1 °C constant) or HS (34 ± 1 °C for 6 h/d), which divided them into eight different treatment groups. Our findings revealed that dietary ZnONPs altered the gene expression of cholecystokinin (ileum), heat stress proteins (HSP) 70 (jejunum and ileum), and HSP 90 (duodenum, jejunum, and ileum). The gene expression of ghrelin was affected by the interaction between the ZnONPs concentration and temperature in the duodenum and stomach. More studies are required to elucidate its complex physiological and biochemical functions of the regulation of gene expression within the intestine in heat-stressed broiler chickens.
    Matched MeSH terms: Zinc Oxide/pharmacology*
  11. Ramiah SK, Awad EA, Mookiah S, Idrus Z
    Poult Sci, 2019 Sep 01;98(9):3828-3838.
    PMID: 30839088 DOI: 10.3382/ps/pez093
    The use of nanominerals, such as nano-zinc, represents a promising and emerging technology in the animal farming industry. Due to the small particle size and bioavailability of nano-zinc, it can be easily assimilated in the digestive system, thereby reducing excretion and environmental pollution. The present study was conducted to assess the effects of zinc oxide nanoparticles (ZnONPs) on the growth performance, zinc (Zn) concentration in edible tissues, thiobarbituric acid reactive substance, and corticosterone concentrations in broilers reared under normal or heat stress environmental conditions. The experiment was performed with a completely randomized design based on a 4 × 2 factorial arrangement consisting of 4 diets (basal diet + 60 mg/kg conventional zinc oxide as control diet; basal diet + 40 mg/kg of ZnONPs; basal diet + 60 mg/kg of ZnONPs; and basal diet + 100 mg/kg of ZnONPs) and 2 environmental conditions (normal and heat stress). On day 22, birds from each dietary group were divided equally to normal temperature (23 ± 1°C throughout) or heat stress conditions (34 ± 1°C daily for 6 h from 10:00 am until 4:00 pm). From 1 to 42 D of age, the broiler chickens fed 100 mg/kg ZnONPs exhibited lower feed intake and feed conversion ratio than the control. The accumulation of Zn in the liver of broilers was significantly higher among all treatment groups compared to breast and thigh muscle tissues regardless of the temperature conditions. At 40 and 60 mg/kg ZnONPs, the malondialdehyde content increased in thigh muscle of broilers at 7 D postmortem, indicating that ZnONPs potentially inhibited the antioxidant system in muscle tissues. The control and ZnONPs at 40 mg/kg and 60 mg/kg led to low serum corticosterone levels that may be attributed to the antioxidant and antistress properties of Zn. Taken together, although supplementation with ZnONPs at 40 mg/kg and 60 mg/kg alleviated the negative results of heat stress, further research is needed to determine the optimal level of dietary ZnONPs supplementation.
    Matched MeSH terms: Zinc Oxide/administration & dosage; Zinc Oxide/metabolism*
  12. Al-Hatamleh MAI, Hussin TMAR, Taib WRW, Ismail I
    J Taibah Univ Med Sci, 2019 Oct;14(5):431-438.
    PMID: 31728141 DOI: 10.1016/j.jtumed.2019.09.003
    Objective: This study aimed to determine the allelic and genotypic association of the Val66Met (rs6265) polymorphism in the BDNF gene with stress levels in preclinical medical students of Universiti Sultan Zainal Abidin (UniSZA), Terengganu, Malaysia.

    Methods: In this cross-sectional study, we recruited all 122 preclinical medical students. The validated depression anxiety stress scales-21 (DASS-21) questionnaire was distributed and blood samples were collected from each subject for DNA extraction. Genotyping analysis of the BDNF gene (Val66Met) polymorphism was performed via an optimised polymerase chain reaction-restriction fragment length polymorphism (PCR-RFLP) method.

    Results: A total of 105 subjects agreed to participate in this study. Indian students were found to more likely have the Val/Val genotype, whereas Malay students were more likely to have the Met/Met genotype (p = 0.027). Individuals carrying any one of the three BDNF genotypes (Val/Val, Val/Met and Met/Met) differed significantly from each other in terms of their perception of stress (p = 0.010); students carrying the Val/Val genotype (M = 10.6) perceived significantly lower stress than students carrying the Val/Met (M = 14) and Met/Met (M = 15.1) genotypes.

    Conclusion: In our study, the Met-allele was associated with higher stress levels. To the best of our knowledge, this is the first study investigating this stress-related gene in medical students. The findings from this study should trigger more investigators to focus on the impact of stress on genetically predisposed medical students.

    Matched MeSH terms: Zinc Oxide
  13. Bhagat V, Haque M, Simbak NB, Jaalam K
    Adv Med Educ Pract, 2016;7:341-6.
    PMID: 27354836 DOI: 10.2147/AMEP.S108477
    Personality dimension negative emotionality is known to be associated with academic achievement. The present study focuses on the influence of negative emotionality (neuroticism) on the medical students' academic achievements. The main objective of this study was to ascertain the negative emotionality scores among the first year Malaysian medical students studying in Malaysia and India, further to find out the association between negative emotionality and their academic achievements. The current study sample includes 60 first year Malaysian medical students from Universiti Sultan Zainal Abidin, Malaysia, and USM-KLE IMP, Belgaum, India. They were selected by convenient sampling technique. The Medico-Psychological questionnaire was used to find out the negative emotionality scores among the students and these scores were compared with academic scores. The data were analyzed using SPSS- 20. Thus, the study result goes with the prediction that there is a significant correlation between academic achievement and negative emotionality. We concluded that negative emotionality has a negative impact on medical student's academic achievement regardless of the fact whether they study in their own country or overseas.
    Matched MeSH terms: Zinc Oxide
  14. Abdollahi Y, Zakaria A, Sairi NA, Matori KA, Masoumi HR, Sadrolhosseini AR, et al.
    ScientificWorldJournal, 2014;2014:726101.
    PMID: 25538962 DOI: 10.1155/2014/726101
    The artificial neural network (ANN) modeling of m-cresol photodegradation was carried out for determination of the optimum and importance values of the effective variables to achieve the maximum efficiency. The photodegradation was carried out in the suspension of synthesized manganese doped ZnO nanoparticles under visible-light irradiation. The input considered effective variables of the photodegradation were irradiation time, pH, photocatalyst amount, and concentration of m-cresol while the efficiency was the only response as output. The performed experiments were designed into three data sets such as training, testing, and validation that were randomly splitted by the software's option. To obtain the optimum topologies, ANN was trained by quick propagation (QP), Incremental Back Propagation (IBP), Batch Back Propagation (BBP), and Levenberg-Marquardt (LM) algorithms for testing data set. The topologies were determined by the indicator of minimized root mean squared error (RMSE) for each algorithm. According to the indicator, the QP-4-8-1, IBP-4-15-1, BBP-4-6-1, and LM-4-10-1 were selected as the optimized topologies. Among the topologies, QP-4-8-1 has presented the minimum RMSE and absolute average deviation as well as maximum R-squared. Therefore, QP-4-8-1 was selected as final model for validation test and navigation of the process. The model was used for determination of the optimum values of the effective variables by a few three-dimensional plots. The optimum points of the variables were confirmed by further validated experiments. Moreover, the model predicted the relative importance of the variables which showed none of them was neglectable in this work.
    Matched MeSH terms: Zinc Oxide/chemistry*
  15. Chong LE, Jow TK
    Dent J Malaysia Singapore, 1967 Oct;7(2):44-51.
    PMID: 5247441
    Matched MeSH terms: Zinc Oxide-Eugenol Cement/therapeutic use
  16. Lee KM, Lai CW, Ngai KS, Juan JC
    Water Res, 2016 Jan 01;88:428-448.
    PMID: 26519627 DOI: 10.1016/j.watres.2015.09.045
    Today, a major issue about water pollution is the residual dyes from different sources (e.g., textile industries, paper and pulp industries, dye and dye intermediates industries, pharmaceutical industries, tannery and craft bleaching industries, etc.), and a wide variety of persistent organic pollutants have been introduced into our natural water resources or wastewater treatment systems. In fact, it is highly toxic and hazardous to the living organism; thus, the removal of these organic contaminants prior to discharge into the environment is essential. Varieties of techniques have been employed to degrade those organic contaminants and advanced heterogeneous photocatalysis involving zinc oxide (ZnO) photocatalyst appears to be one of the most promising technology. In recent years, ZnO photocatalyst have attracted much attention due to their extraordinary characteristics. The high efficiency of ZnO photocatalyst in heterogeneous photocatalysis reaction requires a suitable architecture that minimizes electron loss during excitation state and maximizes photon absorption. In order to further improve the immigration of photo-induced charge carriers during excitation state, considerable effort has to be exerted to further improve the heterogeneous photocatalysis under UV/visible/solar illumination. Lately, interesting and unique features of metal doping or binary oxide photocatalyst system have gained much attention and became favourite research matter among various groups of scientists. It was noted that the properties of this metal doping or binary oxide photocatalyst system primarily depend on the nature of the preparation method and the role of optimum dopants content incorporated into the ZnO photocatalyst. Therefore, this paper presents a critical review of recent achievements in the modification of ZnO photocatalyst for organic contaminants degradation.
    Matched MeSH terms: Zinc Oxide/chemistry*
  17. Kamari Z
    Malays J Med Sci, 2009 Jan;16(1):16-24.
    PMID: 22589644 MyJurnal
    Our Hospital University Sains Malaysia (HUSM) was given the Cabinet approval to exist under the Ministry of Education on 23 November 1982. The Deputy Prime Minister during that period, Yang Berhormat Tun Musa Hitam announced this after the cabinet meeting was held together with the presence of the Yang Berhormat Ministers of Health; and Education, Director of the Public Works Department and the Implementation and Coordinating Unit, Prime Minister's Department. The first patients moved in on 14 March 1983 and the inauguration of HUSM was done on 26 August 1984 by the Duli Yang Maha Mulia Tuanku Ismail Petra Ibni Al-Marhum Sultan Yahya Petra, the Sultan of Kelantan Darul Naim. HUSM celebrated it's 25th anniversary at the Dewan Utama, USM Health Campus on the 15th December 2008 which was inaugurated by Yang Berhormat, Minister of Higher Education Dato' Seri Mohamed Khaled Nordin. USM's Vice Chancellor Professor Tan Sri Dato' Dzulkifli Abdul Razak, Chairman of the USM Board of Directors Tan Sri Dato' Haji Dr. Ani bin Arope, Health Campus Director Professor Dato' Dr. Mafauzy Mohamed, former Campus Director, Dato' Prof Mohd Roslani Abdul Majid, the current and previous Hospital Directors and Deputy Directors since 1983 were present. The achievements of HUSM since its establishment and its vision to fulfil the University's Accelerated Programme for Excellence (APEX) are elaborated.
    Matched MeSH terms: Zinc Oxide
  18. Kasim MF, Darman AKAB, Yaakob MK, Badar N, Kamarulzaman N
    Phys Chem Chem Phys, 2019 Sep 11;21(35):19126-19146.
    PMID: 31432825 DOI: 10.1039/c9cp01664c
    In this study, nano- and microsized zinc oxide (ZnO) materials were doped with different manganese (Mn) contents (1-5 mol%) via a simple sol-gel method. The structural, morphological, optical and chemical environments of the materials were investigated using X-ray diffraction (XRD), field emission scanning electron microscopy (FESEM), energy dispersive X-ray spectroscopy (EDX), UV-visible spectroscopy (UV-vis) and X-ray photoelectron spectroscopy (XPS). XRD results revealed that all synthesised materials were pure and single phased with a hexagonal wurtzite structure of ZnO. However, at a low annealing temperature, a nanorod-like shape can be obtained for all Zn(1-x)MnxO materials. In addition, EDX spectra confirmed the presence of Mn in the ZnO lattice and the atomic percentage was nearly equal to the calculated stoichiometry. UV-vis spectroscopy further revealed that materials in nano size exhibited band gap widening with an increase of the Mn content in the ZnO lattice. In contrast, micron state materials exhibited band gap narrowing with increasing Mn content up to 3% and then begin to widen when Mn > 3%. This is because the band gaps of these materials are affected by the dimensions of the crystals and the Mn content in the materials. Furthermore, XPS results revealed the existence of multiple states of Mn in all synthesised materials. By combining the information obtained from UV-vis and the XPS valence band, shifting in the valence band maximum (VBM) and conduction band minimum (CBM) was observed. Based on XPS results, the calculation of density functional theory studies revealed that the presence of Mn2+, Mn3+, and Mn4+ ions in the materials influences the band gap changes. It was also revealed that the nanosized Zn0.99Mn0.01O exhibited a higher photocatalytic activity than the other samples for degrading methylene blue (MB) dyes, owing to its smallest crystallite size.
    Matched MeSH terms: Zinc Oxide
  19. Rahim Pouran S, Bayrami A, Mohammadi Arvanag F, Habibi-Yangjeh A, Darvishi Cheshmeh Soltani R, Singh R, et al.
    Colloids Surf B Biointerfaces, 2020 May;189:110878.
    PMID: 32087528 DOI: 10.1016/j.colsurfb.2020.110878
    In this research, a milk thistle seed extract (MTSE)-rich medium was used as a capping and reducing agent for the one-pot biosynthesis of ZnO/Ag (5 wt%) nanostructure. The sample was systematically characterized through various techniques and its strong biomolecule‒metal interface structure was supported by the results. The efficacy of the derived nanostructure (MTSE/ZnO/Ag) was evaluated in vivo on the basis of its therapeutic effects on the main complications of Type 1 diabetes (hyperglycemia, hyperlipidemia, and insulin deficiency). For this purpose, the changes in the plasma values of fasting blood glucose, total cholesterol, total triglyceride, high-density lipoprotein cholesterol, and insulin in alloxan-diabetic Wistar male rats were compared with those in healthy and untreated diabetic controls after a treatment period of 16 days. The antidiabetic results of MTSE/ZnO/Ag were compared with those obtained from pristine ZnO, MTSE, and insulin therapies. The health conditions of the rats with Type 1 diabetes were significantly enhanced after treatment with MTSE/ZnO/Ag (p 
    Matched MeSH terms: Zinc Oxide/chemistry
  20. Al-Hardan NH, Abdul Hamid MA, Shamsudin R, Othman NK, Kar Keng L
    Sensors (Basel), 2016 Jun 29;16(7).
    PMID: 27367693 DOI: 10.3390/s16071004
    Zinc oxide (ZnO) nanorods (NRs) have been synthesized via the hydrothermal process. The NRs were grown over a conductive glass substrate. A non-enzymatic electrochemical sensor for hydrogen peroxide (H₂O₂), based on the prepared ZnO NRs, was examined through the use of current-voltage measurements. The measured currents, as a function of H₂O₂ concentrations ranging from 10 μM to 700 μM, revealed two distinct behaviours and good performance, with a lower detection limit (LOD) of 42 μM for the low range of H₂O₂ concentrations (first region), and a LOD of 143.5 μM for the higher range of H₂O₂ concentrations (second region). The prepared ZnO NRs show excellent electrocatalytic activity. This enables a measurable and stable output current. The results were correlated with the oxidation process of the H₂O₂ and revealed a good performance for the ZnO NR non-enzymatic H₂O₂ sensor.
    Matched MeSH terms: Zinc Oxide
Filters
Contact Us

Please provide feedback to Administrator (afdal@afpm.org.my)

External Links