Top-Oil Temperature (TOT) is one of the basic components to estimate the Hot-Spot temperature (HST) of the transformers. This paper presents an alternative TOT model based on the heat transfer theory that utilises Nonlinear Thermal Resistance (NTR) and Lumped Capacitance (LC) approaches. It is applied in a thermal-electrical analogy and the heat transfer equivalent equation is determined. This model is tested on a measured TOT of 250 MVA ONAF and 400 MVA ONAF transformers obtained from IEC 60076-7 and previous research. A comparison of TOT is carried out with the existing models IEC 60076-7 exponential and IEEE Loading Guide clause 7 methods. It is found that the thermal model based on the NTR and LC approach could determine the measured TOT closer than the existing methods available in the standards.
The major aim of this research was to investigate the addition of BPSC on the physical and rheological properties of asphalt binder. In this study, addition of five different percentages of BPSC compositions were studied, namely (2, 4, 6 and 8%). The impact of modifier on the rheological and physical properties was determined using conventional tests, such as softening point, ductility and penetration, and measurements from a dynamic shear rheometer. Based on the results, it was observed that the addition of BPSC has a significant impact on the rheological properties of asphalt binder and would improve rutting resistance at high temperatures. Meanwhile, results related to physical properties indicated that a decrease in penetration and increase in softening points results in stiffness of BPSC. The results showed that BPSC reduced temperature susceptibility and increased stiffness and elastic behaviour in comparison to unmodified asphalt binder. This means BPSC would increase the resistance of permanent deformation (rutting). Finally, BPSC could be considered as an appropriate additive to modify the properties of asphalt binder.
Functionally graded NiTi structures benefit from the combination of the smart properties of NiTi and those of functionally graded structures. This article provides experimental data for thermomechanical deformation behaviour of microstructurally graded, compositionally graded and geometrically graded NiTi alloy components, related to the research article entitled "Functionally graded shape memory alloys: design, fabrication and experimental evaluation" (Shariat et al., 2017) [1]. Stress-strain variation of microstructurally graded NiTi wires is presented at different heat treatment conditions and testing temperatures. The complex 4-way shape memory behaviour of a compositionally graded NiTi strip during one complete thermal cycle is demonstrated. The effects of geometrical design on pseudoelastic behaviour of geometrically graded NiTi plates over tensile loading cycles are presented on the stress-strain diagrams.
This scientific report investigates the heat transfer analysis in mixed convection flow of Maxwell fluid over an oscillating vertical plate with constant wall temperature. The problem is modelled in terms of coupled partial differential equations with initial and boundary conditions. Some suitable non-dimensional variables are introduced in order to transform the governing problem into dimensionless form. The resulting problem is solved via Laplace transform method and exact solutions for velocity, shear stress and temperature are obtained. These solutions are greatly influenced with the variation of embedded parameters which include the Prandtl number and Grashof number for various times. In the absence of free convection, the corresponding solutions representing the mechanical part of velocity reduced to the well known solutions in the literature. The total velocity is presented as a sum of both cosine and sine velocities. The unsteady velocity in each case is arranged in the form of transient and post transient parts. It is found that the post transient parts are independent of time. The solutions corresponding to Newtonian fluids are recovered as a special case and comparison between Newtonian fluid and Maxwell fluid is shown graphically.
The steady two dimensional magnetohydrodynamic (MHD) boundary layer flow and heat transfer over a stretching/shrinking permeable wedge is numerically investigated. The partial differential equations governing the flow and heat transfer are transformed into a system of ordinary differential equations using a similarity transformation. These equations are then solved numerically using the boundary value problem solver, bvp4c in Matlab software. It is found that dual solutions exist for a certain range of the shrinking strength. A stability analysis is performed to identify which solution is stable and physically reliable.
This paper reviews recent progress in the measurement and modelling of stochastic electromagnetic fields, focusing on propagation approaches based on Wigner functions and the method of moments technique. The respective propagation methods are exemplified by application to measurements of electromagnetic emissions from a stirred, cavity-backed aperture. We discuss early elements of statistical electromagnetics in Heaviside's papers, driven mainly by an analogy of electromagnetic wave propagation with heat transfer. These ideas include concepts of momentum and directionality in the realm of propagation through confined media with irregular boundaries. We then review and extend concepts using Wigner functions to propagate the statistical properties of electromagnetic fields. We discuss in particular how to include polarization in this formalism leading to a Wigner tensor formulation and a relation to an averaged Poynting vector.This article is part of the theme issue 'Celebrating 125 years of Oliver Heaviside's 'Electromagnetic Theory''.
This paper presents a numerical analysis of a stagnation-point flow towards a nonlinearly stretching/shrinking sheet immersed in a viscous fluid. The stretching/shrinking velocity and the external flow velocity impinges normal to the stretching/shrinking sheet are assumed to be in the form U ~ xm, where m is a constant and x is the distance from the stagnation point. The governing partial differential equations are converted into ordinary ones by a similarity transformation, before being solved numerically. The variations of the skin friction coefficient and the heat transfer rate at the surface with the governing parameters are graphed and tabulated. Different from a stretching sheet, it is found that the solutions for a shrinking sheet are non-unique for m > 1/3.
The linear stability theory is applied to investigate the effects of rotation and feedback control on the onset of steady and oscillatory thermocapillary convection in a horizontal fluid layer heated from below with a free-slip bottom. The thresholds and codimension-2 points for the onset of steady and oscillatory convection are determined. The effect of feedback control on the parameter space dividing the steady and oscillatory convection regions is demonstrated.
The paper reconsiders the problem of the mixed convection boundary layer flow near the lower stagnation point of a horizontal circular cylinder with a second order slip velocity model and a constant surface heat flux studied recently by RoKa et al. (2013). The ordinary (similarity) differential equations are solved numerically using the function bvp4c from Matlab for different values of the governing parameters. It is found that the similarity equations have two branches, upper and lower branch solutions, in a certain range of the mixed convection parameters. A stability analysis has been performed to show that the upper branch solutions are stable and physically realizable, while the lower branch solutions are not stable and therefore, not physically possible. This stability analysis is different by that presented by RoKa et al. (2013), who have presented a time-dependent analysis to determine the stability of the solution branches.
The magnetohydrodynamic (MHD) boundary-layer flow and heat transfer due to a shrinking sheet in a porous medium is considered for the first time. The Navier-Stokes equations and the heat equation are reduced to two nonlinear ordinary differential equations via similarity transformations. The transformed equations are solved by a semi-analytic method. The effects of the suction and porosity parameters, the Prandtl and Hartmann numbers on the skin friction, heat transfer rate, velocity and temperature profiles are discussed and presented, respectively.
The paper is aimed at studying fluid flow heat transfer in the axisymmetric boundary layer flow of a viscous incompressible fluid, along the axial direction of a vertical stationary isothermal cylinder in presence of uniform free stream with momentum slip. The equations governing the flow i.e. continuity, momentum and energy equation are transformed into non-similar boundary layer equations and are solved numerically employing asymptotic series method with Shanks transformation. The numerical scheme involves the Runge-Kutta fourth order scheme along with the shooting technique. The flow is analyzed for both assisting and opposing buoyancy and the effect of different parameters on fluid velocity, temperature distribution, heat transfer and shear stress parameters is presented graphically.
The unsteady mixed convection boundary layer flow near the forward stagnation point of a two-dimensional symmetric body prescribed by a uniform heat flux rate is studied in this paper. The main aim of the investigation is to identify situations in which dual solutions for the steady-state flow can be determined when the flow is opposing. It is also shown that there is a smooth transition from the unsteady initial flow (short time) to the final steady state flow (large time).
In this study, the numerical solution of stagnation point flow over a stretching surface, generated by Newtonian heating in which the heat transfer from the surface is proportional to the local surface temperature is considered. The transformed boundary layer equations are solved numerically using the shooting method. Numerical solutions are obtained for the local heat transfer coefficient, the surface temperature and the temperature profiles. The features of the flow and heat transfer characteristics for various values of the Prandtl number, stretching parameter and conjugate parameter are analyzed and discussed.
We study and discuss the effect of thermal slip on steady free convection flow of a viscous, incompressible micropolar fluid past a vertical moving plate in a saturated porous medium. The effect of viscous dissipation is incorporated in the energy equation. The associated partial differential equations are transformed into a system of ordinary differential equations using similarity transformations generated by a group method and this system is then solved numerically. The effect of controlling parameters on the dimensionless velocity, angular velocity and temperature as well as friction factor, couple stress factor and heat transfer rate are shown graphically and discussed in detail. It is found that the dimensional velocity and angular velocity decrease whilst the temperature increases with velocity slip parameter. It is further found that thermal slip decreases the dimensional velocity and temperature but increases the dimensional angular velocity. Data from published work and our results are found to be in good agreement.
The thermal characteristics of Actinobacillus succinogenes (AS) from pyrolysis, torrefaction, and combustion are analyzed to evaluate the potential of this biomass as a renewable fuel. AS pyrolysis can be classified into four stages, and its main decomposition zone is at 200-500 °C. The solid yield of AS after 60 min torrefaction is over 60 wt%, and the torrefaction severity index map indicates that a high torrefaction temperature with a short duration has a more profound influence on its decomposition. The Py-GC/MS analysis of AS suggests that the volatile products from 500 °C pyrolysis are similar to microalgae-derived pyrolysis bio-oils. The combustibility index (S) of AS is 4.07 × 10-7 which is much higher than that of lignite coal (0.39 × 10-7) and bituminous coal (0.18 × 10-7), and close to those of biochar and bio-oil. The obtained results are conducive to the development of microorganisms as fuel to achieve a circular bioeconomy.
This study investigated the interactions between volatile and char during biomass pyrolysis at 400 °C, employing a β-5 lignin dimer and amino-modified graphitized carbon nanotube (CNT-NH2) as their models, respectively. The results demonstrated that both -NH2 and its carrier (CNT) facilitated the conversion of the β-5 dimer, which significantly increased from 9.7% (blank run), to 61.6% (with CNT), and to 96.6% (with CNT-NH2). CNT mainly favored the breakage of C-O bond in the feedstock to produce dimers with a yield of 55.5%, while CNT-NH2 promoted the cleavage of both C-O and C-C bonds to yield monomers with a yield up to 63.4%. Such significant changes in the pyrolysis behaviors of the β-5 lignin dimer after the introduction of CNT-NH2 were considered to be mainly caused by hydrogen-bond formations between -NH2 and the dimeric feedstock/products, in addition to the π-π stacking between CNT and aromatic rings.
This study is aimed to rationalise and demonstrate the efficacy of utilising laser cutting technique in the fabrication of glulam mortise & tenon joints in timber frame. Trial-and-error experiments aided by laser cutter were conducted to produce 3D timber mortise & tenon joints models. The two main instruments used were 3D modelling software and the laser cutter TH 1390/6090. Plywood was chosen because it could produce smooth and accurate cut edges whereby the surface could remain crack-free, and it could increase stability due to its laminated nature. Google SketchUp was used for modelling and Laser CAD v7.52 was used to transfer the 3D models to the laser cutter because it is compatible with AI, BMP, PLT, DXF and DST templates. Four models were designed and fabricated in which the trial-and-error experiments proved laser cutting could speed up the manufacturing process with superb quality and high uniformity. Precision laser cutting supports easy automation, produces small heat-affected zone, minimises deformity, relatively quiet and produces low amount of waste. The LaserCAD could not process 3D images directly but needed 2D images to be transferred, so layering and unfolding works were therefore needed. This study revealed a significant potential of rapid manufacturability of mortise & tenon joints with high-quality and high-uniformity through computer-aided laser cutting technique for wide applications in the built environment.
Recently, natural fiber-reinforced polymers (NFRPs) have become important materials in many engineering applications; thus, to employ these materials some final industrial processes are needed, such as cutting, trimming, and drilling. Because of the heterogeneous nature of NFRPs, which differs from homogeneous materials such as metals and polymers, several defects have emerged when processing the NFRPs through traditional cutting methods such as high surface roughness and material damage at cutting zone. In order to overcome these challenges, unconventional cutting methods were considered. Unconventional cutting methods did not take into account the effects of cutting forces, which are the main cause of cutting defects in traditional cutting processes. The most prominent unconventional cutting processes are abrasive waterjet (AWJM) and laser beam (LBM) cutting technologies, which are actually applied for cutting various NFRPs. In this study, previously significant studies on cutting NFRPs by AWJM and LBM are discussed. The surface roughness, kerf taper, and heat-affected zone (HAZ) represent the target output parameters that are influenced and controlled by the input parameters of each process. However, this topic requires further studies on widening the range of material thickness and input parameter values.
Waste furniture boards (WFBs) contain hazardous formaldehyde and volatile organic compounds when left unmanaged or improperly disposed through landfilling and open burning. In this study, pyrolysis was examined as a disposal and recovery approach to convert three types of WFBs (i.e., particleboard, plywood, and fiberboard) into value-added chemicals using thermogravimetric analysis coupled with Fourier-transform infrared spectrometry (TG-FTIR) and pyrolysis coupled with gas chromatography/mass spectrometry (Py-GC/MS). TG-FTIR analysis shows that pyrolysis performed at an optimum temperature of 250-550 °C produced volatile products mainly consisting of carbon dioxide, carbon monoxide, and light hydrocarbons, such as methane. Py-GC/MS shows that pyrolysis at different final temperatures and heating rates recovered mainly phenols (25.9-54.7%) for potential use as additives in gasoline, colorants, and food. The calorific value of WFBs ranged from 16 to 18 MJ/kg but the WFBs showed high H/C (1.7-1.8) and O/C (0.8-1.0) ratios that provide low chemical energy during combustion. This result indicates that WFBs are not recommended to be burned directly as fuel, however, they can be pyrolyzed and converted into solid pyrolytic products such as biochar with improved properties for fuel application. Hazardous components, such as cyclopropylmethanol, were removed and converted into value-added compounds, such as 1,4:3,6-dianhydro-d-glucopyranose, for use in pharmaceuticals. These results show that the pyrolysis of WFBs at high temperature and low heating rate is a promising feature to produce value-added chemicals and reduce the formation of harmful chemical species. Thus, the release of hazardous formaldehyde and greenhouse gases into the environment is redirected.
The application of waste oils as pyrolysis feedstocks to produce high-grade biofuels is receiving extensive attention, which will diversify energy supplies and address environmental challenges caused by waste oils treatment and fossil fuel combustion. Waste oils are the optimal raw materials to produce biofuels due to their high hydrogen and volatile matter content. However, traditional disposal methods such as gasification, transesterification, hydrotreating, solvent extraction, and membrane technology are difficult to achieve satisfactory effects owing to shortcomings like enormous energy demand, long process time, high operational cost, and hazardous material pollution. The usage of clean and safe pyrolysis technology can break through the current predicament. The bio-oil produced by the conventional pyrolysis of waste oils has a high yield and HHV with great potential to replace fossil fuel, but contains a high acid value of about 120 mg KOH/g. Nevertheless, the application of CaO and NaOH can significantly decrease the acid value of bio-oil to close to zero. Additionally, the addition of coexisting bifunctional catalyst, SBA-15@MgO@Zn in particular, can simultaneously reduce the acid value and positively influence the yield and quality of bio-oil. Moreover, co-pyrolysis with plastic waste can effectively save energy and time, and improve bio-oil yield and quality. Consequently, this paper presents a critical and comprehensive review of the production of biofuels using conventional and advanced pyrolysis of waste oils.