Solid-phase microextraction (SPME) coupled to gas chromatography has been applied for the headspace analysis (HS) of 12 target flavour compounds in a model orange beverage emulsion. The main volatile flavour compounds studied were: acetaldehyde, ethyl acetate, alpha-pinene, ethyl butyrate, beta-pinene, myrcene, limonene, gamma-terpinene, octanal, decanal, linalool and citral (neral plus geranial). After screening the fibre type, the effect of other HS-SPME variables such as adsorption temperature (25-55 degrees C), extraction time (10-40 min), sample concentration (1-100% w/w), sample amount (5-10 g) and salt amount (0-30% w/w) were determined using a two-level fractional factorial design (2(5-2)) that was expanded further to a central composite design. It was found that an extraction process using a carboxen-polydimethylsiloxane fibre coating at 15 masculineC for 50 min with 5 g of diluted emulsion 1% (w/w) and 30% (w/w) of sodium chloride under stirring mode resulted in the highest HS extraction efficiency. For all volatile flavour compounds, the linearity values were accurate in the concentration ranges studied (r(2) > 0.97). Average recoveries that ranged from 90.3 to 124.8% showed a good accuracy for the optimised method. The relative standard deviation for six replicates of all volatile flavour compounds was found to be less than 15%. For all volatile flavour compounds, the limit of detection ranged from 0.20 to 1.69 mg/L.
Two formulations of lambda-cyhalothrin (EC-Emulsion concentrate and MC-Microencapsulated) were impregnated into bednets made of polyethylene and polyester. The nets were treated at a dosage of 15 mg/m2. For bioassay of insecticidal efficacy, female Anopheles maculatus and Aedes aegypti were exposed to the nets for two minutes and mortality was scored 24 hours later. The nets were also tested after repeated washings with water and with soap and water. Microencapsulated (2.5CS) formulation was more effective than emulsion concentrate (2.5EC) formulation on both net materials--polyethylene and polyester. Repeated washing with water and soap reduces the efficacy of all bednet treatment combinations. Microencapsulated formulation on polyethylene gave best results; it could sustain up to five washes with water and two with soap and water.
Oxidative stress is intensely involved in enhancing the severity of various chronic respiratory diseases (CRDs) including asthma, chronic obstructive pulmonary disease (COPD), infections and lung cancer. Even though there are various existing anti-inflammatory therapies, which are not enough to control the inflammation caused due to various contributing factors such as anti-inflammatory genes and antioxidant enzymes. This leads to an urgent need of novel drug delivery systems to combat the oxidative stress. This review gives a brief insight into the biological factors involved in causing oxidative stress, one of the emerging hallmark feature in CRDs and particularly, highlighting recent trends in various novel drug delivery carriers including microparticles, microemulsions, microspheres, nanoparticles, liposomes, dendrimers, solid lipid nanocarriers etc which can help in combating the oxidative stress in CRDs and ultimately reducing the disease burden and improving the quality of life with CRDs patients. These carriers improve the pharmacokinetics and bioavailability to the target site. However, there is an urgent need for translational studies to validate the drug delivery carriers for clinical administration in the pulmonary clinic.
A feasible production of poly (methyl methacrylate)@alloy (gold-silver) core shell has
been presented as candidate in enhanced detection of surface enhanced Raman scattering
(SERS). Free emulsifier- emulsion synthesised PMMA sphere with average size of 419 nm in
diameter were used as core material for incorporation of alloy nanoparticles (6 nm) resulting
a core-shell structure. The fabrication of PMMA@alloy SERS substrate was successfully
done via self-assembly thus the produced SERS substrate that comprise of unique optical
properties combination arising from periodic core arrangement and plasmonic activity of
alloy nanoparticles. Alloy is bimetallic nanoparticles in which the combination of silver
(Ag) and gold (Au) present an absolutely improved light resistance as compared to single
metal alone with great surface plasmon resonance. Morphology and elemental analysis was
performed through scanning electron microscope (SEM) and the analysis showing species of
both Au and Ag in single alloy nanoparticles. The alloy nanoparticles were also observed to
homogenously coating the PMMA sphere. Surface plasmon resonance activity was maximum
at 476 nm obtained from UV-Visible spectroscopy. High surface production was observed
to have periodically arranged PMMA@alloy core -shell and potentially to be used as SERS
substrate.
Oil-in-water (o/w) emulsion is utilized as an insecticide delivery system for mosquito control. However, evaporation inhibition adjuvant is needed to prevent fog drift, inhibit release of insecticidal actives and prolong suspension time. In the current study, we evaluated the effect of different short-chain alcohols, namely, propylene glycol, 1,3-propanediol, glycerol and crude glycerol, as adjuvants on the physicochemical properties of d-phenothrin o/w emulsion system. The bioactivity of optimized formulations containing 20 wt% glycerol (D1), 20 wt% propylene glycol (D2) and without added alcohol (negative control) were tested against larvae, pupae and adult Aedes aegypti (Ae. aegypti). It was found that propylene glycol produced smaller droplets at lower concentrations but poor long-term stability at higher concentrations, whereas glycerol had an appreciable effect on initial droplet size and stability with increasing concentration. According to the dose-response bioassays and room size chamber testing, the highest larvicidal, pupicidal and adulticidal activities were observed with D2, followed by D1 and negative control. Overall, the above study demonstrated improved emulsion stabilities and potency against Ae. aegypti larvae, pupae and adults using glycerol as adjuvant for effective mosquito control.
The objective of this study is to investigate the intermolecular interactions between the surfactants and the fractions of heavy crude oils. Two possible interactions were considered; polar and ionic interactions for two heavy crude oil-surfactant systems, and 20 surfactant-steam flooding tests were conducted on these crudes by testing nine surfactants (three anionic, three cationic, and three nonionic) with different tail lengths and charged head groups. The performance differences observed in each core flood were discussed through the additional analyses. To explain polar interactions, the pseudo blends of crude oil fractions (fractionation of saturates, aromatics, resins, and asphaltenes) were exposed to the surfactant solutions under vapor and liquid water conditions and their mutual interactions were visualized under an optical microscope. To explain ionic interactions, the charges on asphaltene surfaces were analyzed by zeta potential measurements before and after core flood tests on both the produced and the residual oil asphaltenes. The addition of surfactants improved the oil recovery when compared to steam injection alone. However, different oil recoveries were obtained with different surfactants. Further analyses showed that asphaltenes are key and the interaction of asphaltenes with other crude oil fractions or surfactants determines the success of surfactant-steam processes. The polar interactions favor the emulsion formation more; hence, if the polar interactions are more dominant than the ion interactions in the overall crude oil-surfactant system, the surfactant flooding process into heavy oil reservoir became more successful.
A comparative study on the optimization of process parameters of an emulsion ionic liquid membrane (EILM) by experimental work and response surface methodology (RSM) has been carried out. EILM was prepared by using kerosene as solvent, Span 80 as surfactant, NaOH as internal reagent, a hydrophobic ionic liquid 1-butyl-3-methylimidazolium bis(trifluoromethylsulfonyl)imide ([BMIM](+)[NTf(2)](-)) as a stabilizer and a second ionic liquid tri-n-octylmethylammonium chloride (TOMAC) as a carrier. The prepared EILM was used to separate and concentrate Cr from wastewaters. The comparison between the experimentally optimized and the RSM optimized values was accomplished by optimizing the following parameters: homogenization speed, carrier concentration, internal phase concentration, agitation speed, treat ratio, internal to membrane phase ratio, surfactant concentration and pH of the feed phase. The comparison showed that all the values were in good agreement except for the internal phase concentration and the treat ratio. It was observed that the stability provided by [BMIM](+)[NTf(2)](-) decreased as the extraction progressed due to its high density. Nevertheless, a good stability could be obtained by the combination of [BMIM](+)[NTf(2)](-) and Span 80 during extraction process.
This study focuses on the role of a hydrophobic ionic liquid 1-butyl-3-methylimidazolium bis(trifluoromethylsulfonyl)imide, [BMIM](+)[NTf(2)](-) in the preparation of emulsion liquid membrane (ELM) phase containing kerosene as solvent, Span 80 as surfactant, NaOH as internal phase and TOMAC (tri-n-octylmethylammonium chloride) a second ionic liquid as carrier. The first time used [BMIM](+)[NTf(2)](-) in ELM was found to play the role of a stabilizer. The emulsion prepared using [BMIM](+) [NTf(2)](-) has a long period of stability of about 7h (at 3% (w/w) of [BMIM](+)[NTf(2)](-)) which otherwise has a brief stability up to only 7 min. The stability of the emulsion increases with the increase in concentration of [BMIM](+)[NTf(2)](-) up to 3% (w/w). Nevertheless, with further increase in concentration of [BMIM](+)[NTf(2)](-), a reduction in the stability occurs. The extraction experiments were carried out after holding the ELM for 2h after the preparation and a removal efficiency of approximately 80% was obtained for Cr. The destabilization of the emulsion was studied by observing the change in the interface height. An empirical correlation for the stability of the emulsion has been proposed.
The percentage removal of phenol from aqueous solution by emulsion liquid membrane and emulsion leakage was investigated experimentally for various parameters such as membrane:internal phase ratio, membrane:external phase ratio, emulsification speed, emulsification time, carrier concentration, surfactant concentration and internal agent concentration. These parameters strongly influence the percentage removal of phenol and emulsion leakage. Under optimum membrane properties, the percentage removal of phenol was as high as 98.33%, with emulsion leakage of 1.25%. It was also found that the necessity of carrier for enhancing phenol removal was strongly dependent on the internal agent concentration.
Today, the increasing use of chemical preservatives in foods is considered one of the main problems in food industries. This study aimed to produce the pasteurised Doogh (Iranian yogurt drink) containing a nanoemulsion of essential oil (EO) with appropriate quality. A factorial test based on a completely randomised design with two treatments in three levels, including EO type (pennyroyal, Gijavash, and their equal combination) and a control sample was applied to assess the physicochemical and sensory properties of Doogh. The highest negative zeta potential and antioxidant activity percentage were observed in the sample containing the nanoemulsion of pennyroyal and enriched with a combination of two essential oils. The microbial evaluation results indicated that the total microorganism count was minimised in the Doogh containing the nanoemulsion of Gijavash. The nanoemulsions of pennyroyal and Gijavash can be added into Doogh formulation to produce a new product with maximum sensory acceptability.
Scale-up in droplet microfluidics achieved by increasing the number of devices running in parallel or increasing the droplet makers in the same device can compromise the narrow droplet-size distribution, or requires high fabrication cost, when glass- or polymer-based microdevices are used. This paper reports a novel way using parallelization of needle-based microfluidic systems to form highly monodispersed droplets with enhanced production rates yet in cost-effective way, even when forming higher order emulsions with complex inner structure. Parallelization of multiple needle-based devices could be realized by applying commercially available two-way connecters and 3D-printed four-way connectors. The production rates of droplets could be enhanced around fourfold (over 660 droplets/min) to eightfold (over 1300 droplets/min) by two-way connecters and four-way connectors, respectively, for the production of the same kind of droplets than a single droplet maker (160 droplets/min). Additionally, parallelization of four-needle sets with each needle specification ranging from 34G to 20G allows for simultaneous generation of four groups of PDMS microdroplets with each group having distinct size yet high monodispersity (CV < 3%). Up to six cores can be encapsulated in double emulsion using two parallelly connected devices via tuning the capillary number of middle phase in a range of 1.31 × 10-4 to 4.64 × 10-4 . This study leads to enhanced production yields of droplets and enables the formation of groups of droplets simultaneously to meet extensive needs of biomedical and environmental applications, such as microcapsules with variable dosages for drug delivery or drug screening, or microcapsules with wide range of absorbent loadings for water treatment.
A series of sugar-based surfactants, involving a single hydrophobic chain (C12) and two side-by-side arranged head groups, was prepared form simple glucose precursors. All surfactants were highly water soluble and exhibited exclusively micellar assemblies. This behavior makes them interesting candidates for oil in water emulsifiers.
An experimental oil emulsion Newcastle disease vaccine was evaluated for its efficacy in broiler chickens. A group of chickens vaccinated at one day old with a live lentogenic Newcastle disease vaccine and subsequently revaccinated at three and eight weeks old with the experimental oil emulsion vaccine showed satisfactory haemagglutination inhibition antibody response which persisted for 18 weeks. Between 90 and 100 per cent of the vaccinated chickens were protected when challenged with the velogenic viscerotropic Newcastle disease virus. Although the vaccinated chickens were protected against clinical disease, virus could be isolated from a number of birds. By day 10 to 12 after challenge all the chickens were free from Newcastle disease infection.
Currently, an extractive green palm oil-based emulsion liquid membrane (ELM) has been used for simultaneous extraction and enrichment of Reactive Red 3BS from simulated synthetic dye wastewater. The ELM consists of two main phases, which are organic liquid membrane (LM) and stripping solution. During the extraction process, the ELM was dispersed into the simulated synthetic dye wastewater containing the Reactive Red 3BS complexes. The organic LM contains tridodecylamine (TDA), Sorbitan Monooleate (Span 80) and palm oil as a carrier, surfactant and diluent, respectively. The sodium bicarbonate (NaHCO3) was used as stripping solution for the enrichment process. Several important parameters that affected the simultaneous extraction and enrichment of Reactive Red 3BS, such as carrier and stripping agent concentrations, extraction time and treat ratio, were investigated. The results showed that almost 90% of Reactive Red 3BS ions were successfully extracted with 10 times enrichment in the stripping phase at the optimum conditions of 0.2 M TDA, 0.1 M NaHCO3, 5 min of extraction time and 1:5 of treat ratio. Hence, it can be concluded that palm oil possesses a high potential as green diluent in future technology, especially in ELM process for the removal and recovery of Reactive Red 3BS from synthetic dye wastewater.
The use of vegetable oil-based ester as a base fluid in synthetic drilling fluid has become a trend in drilling operations due to its environmental advantages. The transesterification reaction of palm oil methyl ester (POME) with 2-ethylhexanol (2EH) produced 98% of palm oil-based ethylhexyl ester in less than 30 minutes. Since the transesterification reaction of POME with 2EH is a reversible reaction, its kinetics was studied in the presence of excess EH and under vacuum. The POME-to-EH molar ratio and vacuum pressure were held constant at 1:2 and 1.5 mbar respectively and the effects of temperature (70 to 110°C) were investigated. Using excess of EH and continual withdrawal of methanol via vacuum promoted the reaction to complete in less than 10 minutes. The rate constant of the reaction (k) obtained from the kinetics study was in the range of 0.44 to 0.66 s⁻¹ and the activation energy was 15.6 kJ.mol⁻¹. The preliminary investigations on the lubrication properties of drilling mud formulated with palm oil-based 2EH ester indicated that the base oil has a great potential to substitute the synthetic ester-based oil for drilling fluid. Its high kinematic viscosity provides better lubrication to the drilling fluid compared to other ester-based oils. The pour point (-15°C) and flash point (204°C) values are superior for the drilling fluid formulation. The plastic viscosity, HPHT filtrate loss and emulsion stability of the drilling fluid had given acceptable values, while gel strength and yield point could be improved by blending it with proper additives.
Gelatin from goatskin pretreated with hydrochloric acid and extracted with distilled water at 60oC for 9 hours was characterized and compared to that of bovine skin gelatin (BSG). A yield of 10.26% (wet weight basis) was obtained. Goatskin gelatin (GSG) had high protein (86.58%), suitable moisture (9.58%), low fat (1.46%) and low ash (0.11%) content. The functional properties of GSG including gel strength (301 g bloom) and emulsion activity index (94.27%) were higher than the functional properties of BSG including gel strength (192 g bloom) and emulsion activity index (49.74%). The foaming property of GSG (102%) was lower than that of BSG (164.67%). This study shows that GSG has a high potential for application as a source of commercial gelatin.
Toxicological studies constitute an essential part of the effort in developing an herbal medicine into a drug product. A newly developed thymoquinone-rich fraction nanoemulsion (TQRFNE) has been prepared using a high pressure homogenizer. The purpose of this study was to investigate the potential acute toxicity of this nanoemulsion in Sprague Dawley rats. The acute toxicity studies were conducted as per the OECD guidelines 425, allowing for the use of test dose limit of 20 mL TQRFNE (containing 44.5 mg TQ)/kg. TQRFNE and distilled water (DW) as a control were administered orally to both sexes of rats on Day 0 and observed for 14 days. All the animals appeared normal, and healthy throughout the study. There was no observed mortality or any signs of toxicity during the experimental period. The effects of the TQRFNE and DW groups on general behavior, body weight, food and water consumption, relative organ weight, hematology, histopathology, and clinical biochemistry were measured. All the parameters measured were unaffected as compared to the control (DW) group. The administration of 20 mL TQRFNE /kg was not toxic after an acute exposure.
Oxidative and nitrosative stress underlies cataractogenesis, and therefore, various antioxidants have been investigated for anticataract properties. Several vitamin E analogs have also been studied for anticataract effects due to their antioxidant properties; however, the anticataract properties of tocotrienols have not been investigated. In this study, we investigated the effects of topically applied tocotrienol on the onset and progression of cataract and lenticular oxidative and nitrosative stress in galactosemic rats.
Palm oil esters (POEs) are esters derived from palm oil and oleyl alcohol have great potential in the cosmetic and pharmaceutical industries due to the excellent wetting behavior of the esters without the oily feel. The role of oil-in-water nanoemulsions loaded with tocotrienol sedimentation behavior was studied. LUMiFuge® 116 particle separation analyzer was used to investigate the sedimentation behavior of POEs/tocotrienol/xanthan gum nanoemulsion system during centrifugation. Analyzing the sedimentation kinetics of dispersions in a centrifugal field also yields information about the rheological behavior and structural stability.
Oil-in-water (O/W) nanoemulsions play an important key role in transporting bioactive compounds into a range of cosmeceutical products to the skin. Small droplet sizes have an inherent stability against creaming, sedimentation, flocculation, and coalescence. O/W emulsions varying in manufacturing process were prepared. The preparation and characterization of O/W nanoemulsions with average diameters of as low as 62.99 nm from palm oil esters were carried out. This was achieved using rotor-stator homogenizer and ultrasonic cavitation. Ultrasonic cell was utilized for the emulsification of palm oil esters and water in the presence of mixed surfactants, Tween 80 and Span 80 emulsions with a mean droplet size of 62.99 nm and zeta potential value at -37.8 mV. Results were comparable with emulsions prepared with rotor-stator homogenizer operated at 6000 rpm for 5 min. The stability of the emulsions was evaluated through rheology measurement properties. This included non-Newtonian viscosity, elastic modulus G', and loss modulus G″. A highly stable emulsion was prepared using ultrasonic cavitation comprising a very small particle size with higher zeta potential value and G' > G″ demonstrating gel-like behavior.