MyMedR

Displaying publications 101 - 120 of 384 in total

Abstract:

Sort:

Morphology and kinetic modeling of molecularly imprinted organosilanol polymer matrix for specific uptake of creatinine

Ang QY, Low SC

Anal Bioanal Chem, 2015 Sep;407(22):6747-58.
PMID: 26163132 DOI: 10.1007/s00216-015-8841-9

Molecular imprinting is an emerging technique to create imprinted polymers that can be applied in affinity-based separation, in particular, biomimetic sensors. In this study, the matrix of siloxane bonds prepared from the polycondensation of hydrolyzed tetraethoxysilane (TEOS) was employed as the inorganic monomer for the formation of a creatinine (Cre)-based molecularly imprinted polymer (MIP). Doped aluminium ion (Al(3+)) was used as the functional cross-linker that generated Lewis acid sites in the confined silica matrix to interact with Cre via sharing of lone pair electrons. Surface morphologies and pore characteristics of the synthesized MIP were determined by field emission scanning electron microscopy (FESEM) and Brunauer-Emmet-Teller (BET) analyses, respectively. The imprinting efficiency of MIPs was then evaluated through the adsorption of Cre with regard to molar ratios of Al(3+). A Cre adsorption capacity of up to 17.40 mg Cre g(-1) MIP was obtained and adsorption selectivity of Cre to its analogues creatine (Cr) and N-hydroxysuccinimide (N-hyd) were found to be 3.90 ± 0.61 and 4.17 ± 3.09, respectively. Of all the studied MIP systems, chemisorption was predicted as the rate-limiting step in the binding of Cre. The pseudo-second-order chemical reaction kinetic provides the best correlation of the experimental data. Furthermore, the equilibrium adsorption capacity of MIP fit well with a Freundlich isotherm (R (2) = 0.98) in which the heterogeneous surface was defined.

Matched MeSH terms: Surface Properties
Cleansing and surface modifying agents on implants: fixation and related aspects of aesthetics

Ling BC, Gillings BR

Asian J Aesthet Dent, 1995;3:17-21.
PMID: 9063105

With the prognosis of dental implant replacement of missing teeth becoming better each year, practitioners are focusing their attention on the aesthetic aspects of implantology. However, improvement in aesthetics is only possible with the improvement in implant technology, surgical techniques and prosthodontic procedures. This study aimed at evaluating the effects of various physical and chemical agents on the implant surface; with the view of obtaining increased surface area and biocompatibility. The study found that the treatment of air-aluminum oxide blasted implants using a mixture of 30% HNO3-5% HF acids produced a surface which meets the consideration of aesthetics for implants placed in the anterior maxillary region.

Matched MeSH terms: Surface Properties
Fulltext Tailoring the surface area and the acid-base properties of ZrO2 for biodiesel production from Nannochloropsis sp

Rahman NJA, Ramli A, Jumbri K, Uemura Y

Sci Rep, 2019 11 07;9(1):16223.
PMID: 31700157 DOI: 10.1038/s41598-019-52771-9

Bifunctional heterogeneous catalysts have a great potential to overcome the shortcomings of homogeneous and enzymatic catalysts and simplify the biodiesel production processes using low-grade, high-free-fatty-acid feedstock. In this study, we developed ZrO2-based bifunctional heterogeneous catalysts for simultaneous esterification and transesterification of microalgae to biodiesel. To avoid the disadvantage of the low surface area of ZrO2, the catalysts were prepared via a surfactant-assisted sol-gel method, followed by hydrothermal treatments. The response surface methodology central composite design was employed to investigate various factors, like the surfactant/Zr molar ratio, pH, aging time, and temperature on the ZrO2 surface area. The data were statistically analyzed to predict the optimal combination of factors, and further experiments were conducted for verification. Bi2O3 was supported on ZrO2 via the incipient wetness impregnation method. The catalysts were characterized by a variety of techniques, which disclosed that the surfactant-assisted ZrO2 nanoparticles possess higher surface area, better acid-base properties, and well-formed pore structures than bare ZrO2. The highest yield of fatty acid methyl esters (73.21%) was achieved using Bi2O3/ZrO2(CTAB), and the catalytic activity of the developed catalysts was linearly correlated with the total densities of the acidic and basic sites. The mechanism of the simultaneous reactions was also discussed.

Matched MeSH terms: Surface Properties
Surface-modified nanocrystalline cellulose from oil palm empty fruit bunch for effective binding of curcumin

Foo ML, Tan CR, Lim PD, Ooi CW, Tan KW, Chew IML

Int J Biol Macromol, 2019 Oct 01;138:1064-1071.
PMID: 31301392 DOI: 10.1016/j.ijbiomac.2019.07.035

Rod-shape particles have been a good drug carrier due to the long circulatory time, tumor accumulation and high cellular uptake in body. Acid-hydrolysed nanocrystalline cellulose (NCC) from empty fruit bunch exhibited a width of 13-30nm and a length of 150-360nm in rod-shape structure. NCC holds good potential as a bio-based drug carrier owing to its biodegradability and biocompatibility. Fourier-transform infrared spectroscopy results confirmed the binding of curcumin onto the NCC modified with tannic acid (TA) and decylamine (DA). TA-DA modification rendered NCC with a higher level of hydrophobicity, as evidenced by a substantial increase in contact angle from 45° to 73°. The modified NCC had the curcumin-binding efficiency in the range of 95-99%, which is at least twofold higher than the unmodified NCC at any curcumin concentration tested. This remarkable curcumin-binding effciency was comparable to that of commercialized NCC from wood-based origin. This work suggests NCC as a superior and sustainable drug carrier, while TA-DA modification is a promising approach to alter the surface property of NCC for an efficient binding of curcumin.

Matched MeSH terms: Surface Properties
Surface morphological and mechanical properties of zinc oxide eugenol using different types of ZnO nanopowder

Bakhori SKM, Mahmud S, Mohamad D, Masudi SM, Seeni A

Mater Sci Eng C Mater Biol Appl, 2019 Jul;100:645-654.
PMID: 30948101 DOI: 10.1016/j.msec.2019.03.034

Zinc oxide eugenol (ZOE) cements are generally made up of 80%-90% ZnO powder while the remaining content consists of eugenol bonding resin. ZnO structure plays a major role in the morphology and mechanical properties of ZOE. In this study, we investigated the effects of different particle sizes/shapes of ZnO particles on the surface and mechanical properties of ZOE. Three samples were prepared namely ZnO-Ax, ZnO-B and ZnO-K. The crystallite sizes calculated from XRD were 37.76 nm (ZnO-Ax), 39.46 nm (ZnO-B) and 42.20 nm (ZnO-K) while the average particle sizes obtained by DLS were 21.11nm (ZnO-Ax), 56.73 nm (ZnO-B) and 2012 nm (ZnO-K). Results revealed that the compressive strengths of ZOE-Ax and ZOE-B were improved by 87.92% and 57.16%, respectively, relative to that of commercial ZOE-K. Vickers hardness test demonstrated that the hardness of ZOE-Ax and ZOE-B also increased by 74.9% and 31.1%, respectively. The ZnO-Ax nanostructure possessed a small average particle size (21.11 nm), a homogeneous size distribution (DLS) and an oxygen-rich surface (from EDS and elemental mapping). Meanwhile, ZnO-B exhibited a slightly larger average particle size of 56.73 nm compared with that of other samples. Sample ZnO-Ax demonstrated the highest compressive strength which was attributed to its large particle surface area (21.11 nm particle size) that provided a large contact area and greater interfacial (or interlock) bonding capability if compared to that of ZnO-K sample (2012 nm particle size).

Matched MeSH terms: Surface Properties
Potential of high-intensity focused ultrasound in resin-dentine bonding

Fawzy AS, Daood U, Matinlinna JP

Dent Mater, 2019 07;35(7):979-989.
PMID: 31003759 DOI: 10.1016/j.dental.2019.04.001

OBJECTIVE: This study introduced the potential and proof-of-concept of high intensity focused ultrasound (HIFU) technology for dentin-surface treatment for resin-dentin bonding without acid-aided demineralization. This new strategy could provide a way to enhance interface-integrity and bond-durability by changing the nature of dentin-substrate; bonded-interface structure and properties; and minimizing denuded-collagen exposure.
METHODS: The interaction between HIFU waves and dentin-surface in terms of structural, mechanical and chemical variations were investigated by SEM, TEM, AFM, nano-indentation and Raman-analysis. The bonding between HIFU-treated dentin and two-step, etch-and-rinse, adhesive was preliminary explored by characterizing dentin-bound proteases activities, resin-dentin interfacial morphology and bond-durability with HIFU exposure at different time-points of 60, 90 and 120 s compared to conventional acid-etching technique.
RESULTS: With the increase in HIFU exposure-time from 60-to-120 s, HIFU waves were able to remove the smear-layer, expose dentinal-tubules and creating textured/rough dentin surface. In addition, dentin surfaces showed a pattern of interlocking ribbon-like minerals-coated collagen-fibrils protruding from the underlaying amorphous dentin-background with HIFU exposure for 90 s and 120 s. This characteristic pattern of dentin-surface showing inorganic-minerals associated/aligned with collagen-fibrils, with 90-to-120 s HIFU-treatment, was confirmed by the Raman-analysis. HIFU-treated specimens showed higher nano-indentation properties and lower concentrations of active MMP-2 and Cathepsin-K compared to the acid-etched specimens. The resin-dentin bonded interface revealed the partial/complete absence of the characteristic hybrid-layer formed with conventional etch-and-rinse bonding strategy. Additionally, resin-infiltration and resin-tags formation were enhanced with the increase in HIFU exposure-time to 120 s. Although, all groups showed significant decrease in bond-strength after 12 months compared to 24 h storage in artificial saliva, groups exposed to HIFU for 90 s and 120 s showed significantly higher μTBS compared to the control acid-etched group.
SIGNIFICANCE: The implementation of HIFU-technology for dental hard-tissues treatment could be of potential significance in adhesive/restorative dentistry owing to its ability of controlled, selective and localised combined tissue alteration/ablation effects.

Matched MeSH terms: Surface Properties
Co-Adsorptive Removal of Creatinine and Urea by a Three-Component Dual-Layer Hollow Fiber Membrane

Zainol Abidin MN, Goh PS, Said N, Ismail AF, Othman MHD, Hasbullah H, et al.

ACS Appl Mater Interfaces, 2020 Jul 22;12(29):33276-33287.
PMID: 32589391 DOI: 10.1021/acsami.0c08947

The development of wearable artificial kidney demands an efficient dialysate recovery, which relies upon the adsorption process. This study proposes a solution to solve the problem of competitive adsorption between the uremic toxins by employing two adsorptive components in a membrane separation process. Dual-layer hollow fiber (DLHF) membranes, which are composed of a polysulfone (PSf)/activated carbon (AC) inner layer and a PSf/poly(methyl methacrylate) (PMMA) outer layer, were prepared for co-adsorptive removal of creatinine and urea from aqueous solution. The DLHF membranes were characterized in terms of morphological, physicochemical, water transport, and creatinine adsorption properties. The membrane was then subjected to an ultrafiltration adsorption study for performance evaluation. The incorporation of AC in membrane, as confirmed by microscopic and surface analyses, has improved the pure water flux up to 25.2 L/(m2 h). A membrane with optimum AC loading (9 wt %) demonstrated the highest maximum creatinine adsorption capacity (86.2 mg/g) based on the Langmuir adsorption isotherm model. In the ultrafiltration adsorption experiment, the membrane removed creatinine and urea with a combined average percent removal of 29.3%. Moreover, the membrane exhibited creatinine and urea uptake recoveries of 98.8 and 81.2%, respectively. The combined action of PMMA and AC in the PSf DLHF membrane has made the adsorption of multiple uremic toxins possible during dialysate recovery.

Matched MeSH terms: Surface Properties
Fulltext Hybrid Nanocellulose-Copper (II) Oxide as Engine Oil Additives for Tribological Behavior Improvement

Hisham S, Kadirgama K, Mohammed HA, Kumar A, Ramasamy D, Samykano M, et al.

Molecules, 2020 Jun 28;25(13).
PMID: 32605301 DOI: 10.3390/molecules25132975

Friction and wear are the main factors in the failure of the piston in automobile engines. The objective of this work was to improve the tribological behaviour and lubricant properties using hybrid Cellulose Nanocrystal (CNC) and Copper (II) oxide nanoparticles blended with SAE 40 as a base fluid. The two-step method was used in the hybrid nanofluid preparation. Three different concentrations were prepared in a range of 0.1% to 0.5%. Kinematic viscosity and viscosity index were also identified. The friction and wear behavior were evaluated using a tribometer based on ASTM G181. The CNC-CuO nano lubricant shows a significant improvement in term of viscosity index by 44.3-47.12% while for friction, the coefficient of friction (COF) decreases by 1.5%, respectively, during high and low-speed loads (boundary regime), and 30.95% during a high-speed, and low load (mixed regime). The wear morphologies results also show that a smoother surface was obtained after using CNC-CuO nano lubricant compared to SAE 40.

Matched MeSH terms: Surface Properties
Role of surface-exposed charged basic amino acids (Lys, Arg) and guanidination in insulin on the interaction and stability of insulin-insulin receptor complex

Lee VS, Sukumaran SD, Tan PK, Kuppusamy UR, Arumugam B

Comput Biol Chem, 2021 Jun;92:107501.
PMID: 33989998 DOI: 10.1016/j.compbiolchem.2021.107501

Naturally occurring proteins are emerging as novel therapeutics in the protein-based biopharmaceutical industry for the treatment of diabetes and obesity. However, proteins are not suitable for oral delivery due to short half-life, reduced physical and chemical stability and low permeability across the membrane. Chemical modification has been identified as a formulation strategy to enhance the stability and bioavailability of protein drugs. The present study aims to study the effect of charge-specific modification of basic amino acids (Lys, Arg) and guanidination on the interaction of insulin with its receptor using molecular modelling. Our investigation revealed that the guanidination of insulin (Lys-NHC = NHNH2) enhanced and exerted stronger binding of the protein to its receptor through electrostatic interaction than native insulin (Lys-NH3+). Point mutations of Lys and Arg (R22, K29; R22K, K29; R22, K29R; R22K, K29R) were attempted and the effects on the interaction and stability between insulin/modified insulins and insulin receptor were also analyzed in this study. The findings from the study are expected to provide a better understanding of the possible mechanism of action of the modified protein at a molecular level before advancing to real experiments.

Matched MeSH terms: Surface Properties
Surface modification and bioactivity of anodic Ti6Al4V alloy

Saharudin KA, Sreekantan S, Abd Aziz SN, Hazan R, Lai CW, Mydin RB, et al.

J Nanosci Nanotechnol, 2013 Mar;13(3):1696-705.
PMID: 23755576

The present study deals with surface modification of Ti6Al4V alloy via anodization technique. The morphology, structure, adhesion and bioactivity of Ti6Al4V alloy after anodization process were investigated in detail. The influence of fluoride content and direct circuit (DC) applied voltage during anodization of Ti6Al4V alloy in a bath with electrolytes composed of ethylene glycol (EG) and ammonium fluoride (NH4F) were considered. It was found that the average pore sizes and length of nanoporous or nanotubes were increasing with the fluoride content and applied voltage. A minimum of 3 wt% of NH4F is required to grow a self-organized nanotube arrays. As the fluoride content was increased to 5 wt%, TiO2 nanotubes with average diameter of 110 nm and 3.4 microm lengths were successfully synthesized. It is noteworthy to point out that the rate of the nanotube formation was increasing up to 9 microm thick bioactive TiO2 nanotubes layer as anodization time was increased to 3 h. Based on the results obtained, the PA6 cells cultured on anodic Ti6Al4V alloy showed highest level of cell viability and greater cell adhesion compared to the flat Ti6Al4V foil substrate. In fact, highly ordered nanotubes structure on Ti6Al4V alloy can provide beneficial effects for PA6 cells in attachment and proliferation.

Matched MeSH terms: Surface Properties
Fulltext Carboxymethyl cellulose from palm oil empty fruit bunch - their properties and use as a film coating agent

Amin, M.C.I., Soom, R.M., Ahmad, I., Lian, H.H.

Jurnal Sains Kesihatan Malaysia, 2006;4(2):53-62.
MyJurnal

This study was carried out to determine the physicochemical properties of carboxymethyl cellulose (CMC) derived from cellulose of palm oil empty fruit bunch (EFB) and its use asa film-coating agent. Samples were prepared at various concentrations and then their physicochemical properties were studied including the viscosity, pH, tensile strength of films, surface properties of the films and dissolution studies on coated tablets. CMC EFB showed lower viscosity than commercial CMC product at the concentration of 1%, 2% and 3% with the values of 44.0cp, 299.9cp, 358.9cp and 90.0cp, 689.9cp, 5569.0cp respectively. The tensile strength of the films for CMC EFB were 7.85MPa, 14.79MPa, 10.36MPa while the commercial CMC exhibited higher values of 21.72MPa, 35.14MPa and 26.9MPa at similar concentration. The scanning electron microscope showed different surface properties of the films for both of them where the commercial CMC is smoother in texture and very transparent unlike its counterpart. However, dissolution studies on paracetamol tablets coated using the samples showed no significant difference (p>0.05) in drug release profile between the two materials. Hence, CMC EFB has a greater potential to be developed as a competitive tablet-coating agent despite the differences in its physicochemical properties.

Matched MeSH terms: Surface Properties
Synthesis of nanostructured titanium dioxide layer onto kaolin hollow fibre membrane via hydrothermal method for decolourisation of reactive black 5

Mohtor NH, Othman MHD, Bakar SA, Kurniawan TA, Dzinun H, Norddin MNAM, et al.

Chemosphere, 2018 Oct;208:595-605.
PMID: 29890498 DOI: 10.1016/j.chemosphere.2018.05.159

Hydrothermal method has been proven to be an effective method to synthesise the nanostructured titanium dioxide (TiO2) with good morphology and uniform distribution at low temperature. Despite of employing a well-known and commonly used glass substrate as the support to hydrothermally synthesise the nanostructured TiO2, this study emphasised on the application of kaolin hollow fibre membrane as the support for the fabrication of kaolin/TiO2 nanorods (TNR) membrane. By varying the hydrothermal reaction times (2 h, 6 h, and 10 h), the different morphology, distribution, and properties of TiO2 nanorods on kaolin support were observed by field emission scanning electron microscopy (FESEM), energy-dispersive X-ray spectroscopy (EDX), atomic force microscope (AFM), X-ray diffraction (XRD) and Fourier transform infrared spectroscopy (FTIR). It was found that the well-dispersed of TiO2 nanorods have improved the surface affinity of kaolin/TNR membrane towards water, allowing kaolin/TNR membrane prepared from 10 h of hydrothermal reaction to exhibit the highest water permeation of 165 L/h.m2.bar. In addition, this prepared membrane also showed the highest photocatalytic activity of 80.3% in the decolourisation of reactive black 5 (RB5) under UV irradiation. On top of that, the kaolin/TNR membrane prepared from 10 h of hydrothermal reaction also exhibited a good resistance towards photocorrosion, enabling the reuse of this membrane for three consecutive cycles of photocatalytic degradation of RB5 without showing significant reduction in photocatalytic efficiency towards the decolourisation of RB5.

Matched MeSH terms: Surface Properties
Long-term wear failure analysis of uhmwpe acetabular cup in total hip replacement

Shahemi N, Liza S, Abbas AA, Merican AM

J Mech Behav Biomed Mater, 2018 11;87:1-9.
PMID: 30031358 DOI: 10.1016/j.jmbbm.2018.07.017

A revision of a metal-on-ultra high molecular weight (UHMWPE) bearing couple for total hip replacement was performed due to aseptic loosening after 23 years in-vivo. It is a major long-term failure identified from wear generation. This study includes performing failure analysis of retrieved polyethylene acetabular cup from Zimmer Trilogy® Acetabular system. The UHMWPE acetabular cup was retrieved from a 61 years old male patient with ability to walk but limited leg movement when he presented to hospital in early 2016 with complaint left thigh pain. It was 23 years after his primary total hip replacement procedure. Surface roughness and morphology condition were measured using 3D laser microscope and Scanning Electron Microscope (SEM) to evaluate and characterize the wear features on polyethylene acetabular cup surface. ATR-Fourier Transform Infra-Red (ATR-FTIR), differential scanning calorimetry (DSC) and gel permeation chromatography (GPC) were used to characterize the chemical composition of carbon-oxygen bonding, crystallinity percentage and molecular weight of the polymer liner that might changes the mechanical properties of polyethylene. Nano indentation is to measure hardness and elasticity modulus where the ratio of hardness to elastic modulus value can be reflected as the degradation of mechanical properties. A prominent difference of thickness between two regions resulted from acentric loading concentration was observed and wear rate were measured. The linear wear rate for thin side and thick side were 0.33 mm/year and 0.05 mm/year respectively. Molecular weight reduction of 57.5% and relatively low ratio of hardness to elastic modulus (3.59 × 10-3) were the indicator of major mechanical properties degradation happened on UHMWPE acetabular cup. This major degradation was contributed by oxidation and polishing wear feature accompanied with delamination, craters, ripple and cracks were the indication of extensive usage of UHMWPE from the suggested life span of acetabular cup application.

Matched MeSH terms: Surface Properties
Fulltext A Surfactant Directed Microcrystalline Cellulose/Polyaniline Composite with Enhanced Electrochemical Properties

Abdi MM, Md Tahir P, Liyana R, Javahershenas R

Molecules, 2018 Sep 26;23(10).
PMID: 30261640 DOI: 10.3390/molecules23102470

In this study a cationic surfactant, cetyltrimethylammonium bromide (CTAB), was used as a soft template for in situ chemical polymerization of aniline on the surface of microcrystalline cellulose (MCC). The morphology of the wire-like and porous nanostructure of the resulting composite was highly dependent on the MCC and CTAB concentrations. The effect of the MCC and CTAB concentrations on the electrochemical and morphological properties of the polyaniline (PAni) nanocomposite was studied. Cyclic voltammograms of modified PAni/MCC/CTAB electrode displayed a high current response and the effect of scan rate on the current response confirmed a diffusion controlled process on the surface of the electrode that makes it suitable for sensor applications. The overlapping characteristic peaks of pure PAni and MCC caused peak broadening at 3263 cm-1 in the IR spectra of PAni/MCC/CTAB nanocomposite that revealed the interaction between NH of PAni and OH group of MCC via electrostatic interactions. The addition of MCC to PAni through chemical polymerization decreased the thermal stability of composite compared to pure PAni. Lower crystallinity was observed in the XRD diffractogram, with 2 theta values of 22.8, 16.5, and 34.6 for PAni/MCC, confirming the formation of PAni on the MCC surface.

Matched MeSH terms: Surface Properties
Fulltext Improving Water Permeability of Hydrophilic PVDF Membrane Prepared via Blending with Organic and Inorganic Additives for Humic Acid Separation

Arahman N, Mulyati S, Fahrina A, Muchtar S, Yusuf M, Takagi R, et al.

Molecules, 2019 Nov 13;24(22).
PMID: 31766222 DOI: 10.3390/molecules24224099

The removal of impurities from water or wastewater by the membrane filtration process has become more reliable due to good hydraulic performance and high permeate quality. The filterability of the membrane can be improved by having a material with a specific pore structure and good hydrophilic properties. This work aims at preparing a polyvinylidene fluoride (PVDF) membrane incorporated with phospholipid in the form of a 2-methacryloyloxyethyl phosphorylcholine, polymeric additive in the form of polyvinylpyrrolidone, and its combination with inorganic nanosilica from a renewable source derived from bagasse. The resulting membrane morphologies were analyzed by using scanning electron microscopy. Furthermore, atomic force microscopy was performed to analyze the membrane surface roughness. The chemical compositions of the resulting membranes were identified using Fourier transform infrared. A lab-scale cross-flow filtration system module was used to evaluate the membrane's hydraulic and separation performance by the filtration of humic acid (HA) solution as the model contaminant. Results showed that the additives improved the membrane surface hydrophilicity. All modified membranes also showed up to five times higher water permeability than the pristine PVDF, thanks to the improved structure. Additionally, all membrane samples showed HA rejections of 75-90%.

Matched MeSH terms: Surface Properties
Synthesis, characterization, ecotoxicity and biodegradability evaluations of novel biocompatible surface active lauroyl sarcosinate ionic liquids

Mustahil NA, Baharuddin SH, Abdullah AA, Reddy AVB, Abdul Mutalib MI, Moniruzzaman M

Chemosphere, 2019 May 04;229:349-357.
PMID: 31078892 DOI: 10.1016/j.chemosphere.2019.05.026

Ionic liquids (ILs) based surfactants have been emerged as attractive alternatives to the conventional surfactants owing to their tailor-made and eco-friendly properties. Therefore, present study described the synthesis of nine new fatty amino acids based IL surfactants utilizing lauroyl sarcosinate anion and pyrrolidinium, imidazolium, pyridinium, piperidinium, morpholinium and cholinium cations for the first time. The synthesized surface active lauroyl sarcosinate ionic liquids (SALSILs) were characterized by 1H NMR, 13C NMR and TGA. Next, the surface tension and critical micellar concentrations were determined and compared with the surface properties of ILs based surfactants. Further, the toxicity and biodegradability of the synthesized SALSIILs were evaluated to confirm their safe and efficient process applications. The studies revealed that three out of nine synthesized SALSILs containing pyridinium cation have showed strong activity towards the tested microbial growth. The remaining six SALSILs met the biocompatible measures demonstrating moderate to low activity depends on the tested microbes. The alicyclic SALSILs containing morpholinium and piperidinium cations have demonstrated 100% biodegradation after 28 days of the test period. Overall, it is believed that the synthesized SALSILs could effectively replace the conventional surfactants in a wide variety of applications.

Matched MeSH terms: Surface Properties
Surface properties of chitin-glucan nanopapers from Agaricus bisporus

Nawawi WMFW, Lee KY, Kontturi E, Bismarck A, Mautner A

Int J Biol Macromol, 2020 Apr 01;148:677-687.
PMID: 31954796 DOI: 10.1016/j.ijbiomac.2020.01.141

The structural component of fungal cell walls comprises of chitin covalently bonded to glucan; this constitutes a native composite material (chitin-glucan, CG) combining the strength of chitin and the toughness of glucan. It has a native nano-fibrous structure in contrast to nanocellulose, for which further nanofibrillation is required. Nanopapers can be manufactured from fungal chitin nanofibrils (FChNFs). FChNF nanopapers are potentially applicable in packaging films, composites, or membranes for water treatment due to their distinct surface properties inherited from the composition of chitin and glucan. Here, chitin-glucan nanofibrils were extracted from common mushroom (Agaricus bisporus) cell walls utilizing a mild isolation procedure to preserve the native quality of the chitin-glucan complex. These extracts were readily disintegrated into nanofibre dimensions by a low-energy mechanical blending, thus making the extract dispersion directly suitable for nanopaper preparation using a simple vacuum filtration process. Chitin-glucan nanopaper morphology, mechanical, chemical, and surface properties were studied and compared to chitin nanopapers of crustacean (Cancer pagurus) origin. It was found that fungal extract nanopapers had distinct physico-chemical surface properties, being more hydrophobic than crustacean chitin.

Matched MeSH terms: Surface Properties
Fulltext Surface, thermal and hemocompatible properties of novel single stage electrospun nanocomposites comprising polyurethane blended with bio oilTM

Ayyar M, Mani MP, Jaganathan SK, Rathinasamy R, Khudzari AZ, Krishnasamy NP

An Acad Bras Cienc, 2017;89(3 Suppl):2411-2422.
PMID: 29091109 DOI: 10.1590/0001-3765201720170230

In this work, the physicochemical and blood compatibility properties of prepared PU/Bio oil nanocomposites were investigated. Scanning electron microscope (SEM) studies revealed the reduction of mean fiber diameter (709 ± 211 nm) compared to the pristine PU (969 nm ± 217 nm). Fourier transform infrared spectroscopy (FTIR) analysis exposed the characteristic peaks of pristine PU. Composite peak intensities were decreased insinuating the interaction of the bio oilTM with the PU. Contact angle analysis portrayed the hydrophobic nature of the fabricated patch compared to pristine PU. Thermal gravimetric analysis (TGA) depicted the better thermal stability of the novel nanocomposite patch and its different thermal behavior in contrast with the pristine PU. Atomic force microscopy (AFM) analysis revealed the increase in the surface roughness of the composite patch. Activated partial thromboplastin time (APTT) and prothrombin time (PT) signified the novel nanocomposite patch ability in reducing the thrombogenicity and promoting the anticoagulant nature. Finally the hemolytic percentage of the fabricated composite was in the acceptable range revealing its safety and compatibility with the red blood cells. To reinstate, the fabricated patch renders promising physicochemical and blood compatible nature making it a new putative candidate for wound healing application.

Matched MeSH terms: Surface Properties
Box-Behnken design optimisation of a green novel nanobio-based reagent for rapid visualisation of latent fingerprints on wet, non-porous substrates

Azman AR, Mahat NA, Wahab RA, Ahmad WA, Puspanadan JK, Huri MAM, et al.

Biotechnol Lett, 2021 Apr;43(4):881-898.
PMID: 33389272 DOI: 10.1007/s10529-020-03052-3

OBJECTIVE: Optimisation of the green novel nanobio-based reagent (NBR) for rapid visualisation of groomed fingerprints on wet non-porous substrates using response surface methodology and assessment of its stability and sensitivity were attempted for forensic applications.
RESULTS: Scanning electron microscopy images demonstrated successful attachments of NBR onto the constituents of fingerprints on the substrates. The highest average quality of visualised fingerprints was attained at the optimum condition (100 mg of CRL; 75 mg of acid-functionalised multi-walled carbon nanotubes; 5 h of immobilisation). The NBR produced comparable average quality of fingerprints with the commercially available small particle reagent, even after 4 weeks of storage (without any preservatives) in both chilled and sultry conditions. The NBR was sensitive enough to visualise the increasingly weaker fingerprints, particularly on glass slides.
CONCLUSION: The optimised novel NBR could be the relatively greener option for visualising latent fingerprints on wet, non-porous substrates for forensic applications.

Matched MeSH terms: Surface Properties
Feasibility of graphene in biomedical applications

Foo ME, Gopinath SCB

Biomed Pharmacother, 2017 Oct;94:354-361.
PMID: 28772213 DOI: 10.1016/j.biopha.2017.07.122

Nanotechnology is the developing field, bringing the materials in the nanoscale level, has been applied in the interdisciplinary sciences. Different nanomaterials, such as gold, silver, zinc, copper and graphene are shown to have a wide range of applications. Among these, graphene is one of the faster upcoming two-dimensional nanomaterials utilized in various fields due to its positive features including the properties of thermal, electrical, strength and elasticity. Biomedical applications of graphene have been widely attested to be popular among academician and industrial partners for creating next generation medical systems and therapies. In this review, we selectively revealed the current applications of graphene in the interdisciplinary medical sciences.

Matched MeSH terms: Surface Properties

Filters

Please provide feedback to Administrator (afdal@afpm.org.my)

External Links