Displaying publications 121 - 140 of 276 in total

Abstract:
Sort:
  1. Monte Carlo skin dose simulation in intraoperative radiotherapy of breast cancer using spherical applicators
    Moradi F, Ung NM, Khandaker MU, Mahdiraji GA, Saad M, Abdul Malik R, et al.
    Phys Med Biol, 2017 Jul 28;62(16):6550-6566.
    PMID: 28708603 DOI: 10.1088/1361-6560/aa7fe6
    The relatively new treatment modality electronic intraoperative radiotherapy (IORT) is gaining popularity, irradiation being obtained within a surgically produced cavity being delivered via a low-energy x-ray source and spherical applicators, primarily for early stage breast cancer. Due to the spatially dramatic dose-rate fall off with radial distance from the source and effects related to changes in the beam quality of the low keV photon spectra, dosimetric account of the Intrabeam system is rather complex. Skin dose monitoring in IORT is important due to the high dose prescription per treatment fraction. In this study, modeling of the x-ray source and related applicators were performed using the Monte Carlo N-Particle transport code. The dosimetric characteristics of the model were validated against measured data obtained using an ionization chamber and EBT3 film as dosimeters. By using a simulated breast phantom, absorbed doses to the skin for different combinations of applicator size (1.5-5 cm) and treatment depth (0.5-3 cm) were calculated. Simulation results showed overdosing of the skin (>30% of prescribed dose) at a treatment depth of 0.5 cm using applicator sizes larger than 1.5 cm. Skin doses were significantly increased with applicator size, insofar as delivering 12 Gy (60% of the prescribed dose) to skin for the largest sized applicator (5 cm diameter) and treatment depth of 0.5 cm. It is concluded that the recommended 0.5-1 cm distance between the skin and applicator surface does not guarantee skin safety and skin dose is generally more significant in cases with the larger applicators.

    HIGHLIGHTS: • Intrabeam x-ray source and spherical applicators were simulated and skin dose was calculated. • Skin dose for constant skin to applicator distance strongly depends on applicator size. • Use of larger applicators generally results in higher skin dose. • The recommended 0.5-1 cm skin to applicator distance does not guarantee skin safety.

    Matched MeSH terms: X-Rays
  2. Fulltext Dihydrotestosterone, a robust promoter of osteoblastic proliferation and differentiation: understanding of time-mannered and dose-dependent control of bone forming cells
    Thu HE, Mohamed IN, Hussain Z, Shuid AN
    Iran J Basic Med Sci, 2017 Aug;20(8):894-904.
    PMID: 29085581 DOI: 10.22038/IJBMS.2017.9111
    OBJECTIVES: The present study was aimed to evaluate the time-mannered and dose-dependent effects of 5α-dihydrotestosterone (5α-DHT) on the proliferation and differentiation of bone forming cells using MC3T3-E1 cells.

    MATERIALS AND METHODS: Cell proliferation was analyzed using MTS and phase contrast microscopic assays. Osteogenic differentiation was assessed through a series of in vitro experiments including crystal violet staining, alkaline phosphatase (ALP) activity, and Van Gieson (VG) staining. Taken together, the efficiency of bone mineralization was examined by using alizarin red s (ARS) staining, Von Kossa staining, scanning electron microscopy (SEM) and energy dispersive x-ray (EDX) analysis.

    RESULTS: The resulting data revealed that 5α-DHT exhibits promising potential particularly at a dose of 0.1 ng/ml, in promoting the growth of MC3T3-E1 cells compared to the control group (CN). Moreover, a significantly higher ALP activity was evident in the experimental group treated with 5α-DHT compared to the CN group at various time intervals. MC3T3-E1 cells treated with 5α-DHT also expressed a remarkably higher collagen deposition and mineralization (calcium and phosphate contents) compared to the CN group at various time intervals.

    CONCLUSION: Conclusively, we suggest that 5α-DHT exhibits outstanding potential of promoting proliferation and differentiation in osteoblasts which could be the in vitro basis for the efficacy of 5α-DHT in the treatment of androgen-deficient male osteoporosis.

    Matched MeSH terms: X-Rays
  3. Biomineralized Conductive PEDOT: PSS-Coated PLA/PHBV/HA Nanofibrous Membranes
    Hassan MI, Masnawi NN, Sultana N
    ASAIO J., 2017 9 14;64(3):415-423.
    PMID: 28901994 DOI: 10.1097/MAT.0000000000000655
    Conductive materials are potential candidates for developing bone tissue engineering scaffolds as they are nontoxic and can enhance bone tissue regeneration. Their bioactivity can be enhanced by depositing biomineralization in simulated body fluid (SBF). In the current study, a composite electrospun membrane made up of poly(lactic) acid, poly(3-hydroxybutyrate-co-3-hydroxyvalerate), and hydroxyapatite was fabricated using an electrospinning method. The fabricated membranes were dip-coated with a conductive polymer solution, poly(3,4-ethylenedioxythiophene) poly(4-styrenesulfonate), to induce conductivity. Characterization of the membranes based on characteristics such as morphology, chemical bonding, and wettability was conducted using scanning electron microscopy, field emission scanning electron microscopy, energy-dispersive X-ray spectroscopy, attenuated total reflectance Fourier transform infrared spectroscopy, and contact angle measurement. From the results, biomineralization of both coated and noncoated composite membranes was observed on the surface of nanofibers after 21 days in SBF. The membranes provide a superhydrophilic surface as shown by the contact angle. In conclusion, this biomimetic electrospun composite membrane could be used to further support cell growth for bone tissue engineering application.
    Matched MeSH terms: X-Rays
  4. Bioactivity and Cell Compatibility of β-Wollastonite Derived from Rice Husk Ash and Limestone
    Shamsudin R, Abdul Azam F', Abdul Hamid MA, Ismail H
    Materials (Basel), 2017 Oct 17;10(10).
    PMID: 29039743 DOI: 10.3390/ma10101188
    The aim of this study was to prepare β-wollastonite using a green synthesis method (autoclaving technique) without organic solvents and to study its bioactivity. To prepare β-wollastonite, the precursor ratio of CaO:SiO₂ was set at 55:45. This mixture was autoclaved for 8 h and later sintered at 950 °C for 2 h. The chemical composition of the precursors was studied using X-ray fluorescence (XRF), in which rice husk ash consists of 89.5 wt % of SiO₂ in a cristobalite phase and calcined limestone contains 97.2 wt % of CaO. The X-ray diffraction (XRD) patterns after sintering showed that only β-wollastonite was detected as the single phase. To study its bioactivity and degradation properties, β-wollastonite samples were immersed in simulated body fluid (SBF) for various periods of time. Throughout the soaking period, the molar ratio of Ca/P obtained was in the range of 1.19 to 2.24, and the phase detected was amorphous calcium phosphate, which was confirmed by scanning electron microscope with energy dispersive X-ray analysis (SEM/EDX) and XRD. Fourier-transform infrared spectroscopy (FTIR) analysis indicated that the peaks of the calcium and phosphate ions increased when an amorphous calcium phosphate layer was formed on the surface of the β-wollastonite sample. A cell viability and proliferation assay test was performed on the rice husk ash, calcined limestone, and β-wollastonite samples by scanning electron microscope. For heavy metal element evaluation, a metal panel that included As, Cd, Pb, and Hg was selected, and both precursor and β-wollastonite fulfilled the requirement of an American Society for Testing and Materials (ASTM F1538-03) standard specification. Apart from that, a degradation test showed that the loss of mass increased incrementally as a function of soaking period. These results showed that the β-wollastonite materials produced from rice husk ash and limestone possessed good bioactivity, offering potential for biomedical applications.
    Matched MeSH terms: X-Rays
  5. Fulltext Determining the Effect of Centrifugal Force on the Desired Growth and Properties of PCPDTBT as p-Type Nanowires
    Doris M, Aziz F, Alhummiany H, Bawazeer T, Alsenany N, Mahmoud A, et al.
    Nanoscale Res Lett, 2017 Dec;12(1):67.
    PMID: 28116608 DOI: 10.1186/s11671-017-1851-0
    In this study, low-bandgap polymer poly{[4,4-bis(2-ethylhexyl)-cyclopenta-(2,1-b;3,4-b')dithiophen]-2,6-diyl-alt-(2,1,3-benzothiadiazole)-4,7-diyl} (PCPDTBT) nanostructures have been synthesized via a hard nanoporous alumina template of centrifugal process. Centrifuge has been used to infiltrate the PCPDTBT solution into the nanoporous alumina by varying the rotational speeds. The rotational speed of centrifuge is directly proportional to the infiltration force that penetrates into the nanochannels of the template. By varying the rotational speed of centrifuge, different types of PCPDTBT nanostructures are procured. Infiltration force created during the centrifugal process has been found a dominant factor in tuning the morphological, optical, and structural properties of PCPDTBT nanostructures. The field emission scanning electron microscopy (FESEM) images proved the formation of nanotubes and nanowires. The energy-dispersive X-ray spectroscope (EDX) analysis showed that the nanostructures were composed of PCPDTBT with complete dissolution of the template.
    Matched MeSH terms: X-Rays
  6. Fulltext Prevalence and Factors Associated with Tuberculosis Treatment Success among TB/HIV Co-Infection in North-East Malaysia
    Jalal TMT, Abdullah S, Wahab FA, Dir S, Naing NN
    Malays J Med Sci, 2017 Dec;24(6):75-82.
    PMID: 29379389 DOI: 10.21315/mjms2017.24.6.9
    Background: One of the six strategies developed by WHO, in order to stop Tuberculosis (TB) is addressing TB/HIV high-risk groups. This study aimed to determine the prevalence of successful TB treatment and factors associated with TB treatment success among TB/HIV co-infection patients in North-East Malaysia.
    Methods: A cross-sectional study was carried out in the a-year period from 2003 to 2012 by reviewing TB/HIV records in all hospitals and health clinics. The outcome of interest was treatment success as defined by Ministry of Health (MOH) when the patients was cured or completed TB treatment.
    Results: Out of 1510 total TB/HIV co-infection cases, 27.9% (95% CI: 25.2, 30.6) of the patients were having treatment success. A majority of TB/HIV co-infection cases were male (91.1%). Fifty-eight percent the patients were drug addicts and 6% were having positive tuberculin tests. The multiple logistic regression revealed that male (OR: 0.39, 95% CI: 0.22, 0.71) and positive tuberculin test result (OR: 2.61, 95% CI: 1.63, 4.19) were significantly associated with the treatment success of TB/HIV co-infection patients. Other factors such as age, comorbid, sputum smear and x-ray findings were not significantly factors in this study.
    Conclusion: Female patients and those with negative tuberculin test should be emphasised for successful tuberculosis treatment.
    Matched MeSH terms: X-Rays
  7. Fulltext Validation of the dose distributions with Monte Carlo simulation for carbon ion cancer therapy
    Ying, C.K., W.A. Kamil, Matsufuji, Naruhiro
    Journal of Biomedical and Clinical Sciences, 2017;2(2):1-7.
    MyJurnal
    Charged particle therapy with carbon ions has advantages over conventional radiotherapy using x-ray beams. The application of charged particle therapy has rapidly increased over the last decades. This is due to its characteristic Bragg peak which has relatively low entrance doses and favourable doses distribution. In this research work, Geant4 based Monte Carlo simulation (MC) method has been used to calculate the radiation transportation and dose distributions in tissue-like media. The main objective of the work was to compare the Geant4 simulated depth dose distributions with experimental measurements and verify the capability of the geant4 simulation toolkit. The carbon ion beams for the therapeutic energy of 350 MeV/u and 400 MeV/u respectively were simulated, with the same settings as the experimental work carried out at the treatment room at Heavy Ion Medical Accelerator (HIMAC), National Institute of Radiological Sciences (NIRS), Chiba, Japan. The simulation results were verified with measurements data. The work was to measure the accuracy and quality of the dose distributions by Geant4 MC methods. The results show that the Bragg peak and spread out Bragg peak (SOBP) distributions in simulation has fairly good agreement with measurements.
    Matched MeSH terms: X-Rays
  8. Fulltext PVC as a potential filter material for ionising radiation
    Laila Kalidah Junet, Zafri Azran Abdul Majid, Muhammad Syahmi Che Othaman
    International Journal of Allied Health Sciences, 2017;1(2):101-107.
    MyJurnal
    Aluminum (Al) is a standard material that has been used as a filter for ionising radiation however for polyvinyl chloride (PVC) there is no solid evidence to support but has been recommended. PVC has been selected as a potential filter material due to it is a long lasting constructing material and very durable, which can be used in a variety of application. The purpose of this study was to observe the effect of PVC on entrance surface dose (ESD) values as compare to the standard X-ray filter of Al. The effect of varying thickness of the materials and difference exposure settings were observed and compared to each other. From this study, the percentage difference for both PVC and Al thickness is less than ± 25.00 % shows that PVC has a potential to be used as one of the filter materials due to its ability to reduce the ESD value
    Matched MeSH terms: X-Rays
  9. Fulltext Assessment of blurring effect and its associated factors by using imagej: a multiparameter double holes contrast-detail phantom study
    Nur Farahana Pauzi, Zafri Azran Abdul Majid, Wan Muhamad Nasuha Wan Hussin, Abdul Halim Sapuan, Mohd Zulfaezal Che Azemin
    International Journal of Allied Health Sciences, 2017;1(2):107-119.
    MyJurnal
    X-ray is produced in form of divergent beam. The beam divergence results to blurring effect that influences image diagnosis. Thus, the blurring effect assessment should be enrolled within the quality control (QC) program of an imaging unit.
    Matched MeSH terms: X-Rays
  10. Fulltext An experiment of using x-ray microtomography (XMT) to study the depth of bonding agent penetration into dentinal tubules
    Norzaiti Mohd Kenali
    International Medical Journal Malaysia, 2017;16(21):60-60.
    MyJurnal
    This is a novel study of the depth of penetration of bonding agents (BA) by using a
    miniaturised CT-scan, XMT.The Linear Attenuation Coefficient describes the fraction of a beam of
    x-rays or gamma rays that is absorbed or scattered per unit thickness of the absorber. The higher
    the LAC, the more opaque the image is. (Copied from article).
    Matched MeSH terms: X-Rays
  11. Fulltext Adsorption of acid dyes onto Zinc Chloride-Modified Cocoa (Theobroma Cacao) pod Husk-based carbon
    Nur Aqilah Zainal, Shariff Ibrahim, Borhannuddin Arifin
    Pertanika Journal of Science & Technology, 2017;25(103):129-138.
    MyJurnal
    An agricultural waste, the cocoa pod husk was chemically modified using a dehydrating agent, zinc chloride (ZnCl2), carbonised and used for the remediation of acid dyes in an aqueous solution. The targeted acid dyes are: (i) Acid Violet 17 (AV17); (ii) Acid Yellow 36 (AY36); and (iii) Acid Blue 29 (AB29). The physicochemical properties of the zinc chloride-modified cocoa pod husk-based carbon (ZCPHC) were characterised by ash content, bulk density, pH slurry, pHpzc and Field Emission Scanning Electron Microscopy (FESEM) and Energy Dispersive X-Ray (EDX) analysis. The bulk density and ash content of the prepared carbon is 0.55 g cm-1 and 7.0% respectively. The photograph of SEM shows distinct changes at the ZCPHC carbon surface as it has large pores formed due to ZnCl2 modification. The adsorption tests were performed in a batch adsorption system using an aqueous solution of the understudy acid dyes. The influence of pH and dose of an adsorbent on the acid dye uptake was investigated and discussed. The adsorption was in favour at acidic condition with maximum removal observed at pH 2. The removal efficiency of the aqueous acid dye solution increased with the increase in adsorbent dosage. The kinetic experiment showed equilibrium time is less than 40 minutes and the kinetic data for all three understudy acid dyes fitted well with the pseudo-second-order model with a correlation coefficient (R2) values above 0.98.
    Matched MeSH terms: X-Rays
  12. Fulltext Distribution of Silicified Microstructures, Regulation of Cinnamyl Alcohol Dehydrogenase and Lodging Resistance in Silicon and Paclobutrazol Mediated Oryza sativa
    Dorairaj D, Ismail MR
    Front Physiol, 2017;8:491.
    PMID: 28747889 DOI: 10.3389/fphys.2017.00491
    Lodging is a phenomenon that affects most of the cereal crops including rice, Oryza sativa. This is due to the fragile nature of herbaceous plants whose stems are non-woody, thus affecting its ability to grow upright. Silicon (Si), a beneficial nutrient is often used to toughen and protect plants from biotic and abiotic stresses. Deposition of Si in plant tissues enhances the rigidity and stiffness of the plant as a whole. Silicified cells provide the much needed strength to the culm to resist breaking. Lignin plays important roles in cell wall structural integrity, stem strength, transport, mechanical support, and plant pathogen defense. The aim of this study is to resolve effects of Si on formation of microstructure and regulation of cinnamyl alcohol dehydrogenase (CAD), a key gene responsible for lignin biosynthesis. Besides evaluating silicon, paclobutrazol (PBZ) a plant growth retartdant that reduces internode elongation is also incorporated in this study. Hardness, brittleness and stiffness were improved in presence of silicon thus reducing lodging. Scanning electron micrographs with the aid of energy dispersive x-ray (EDX) was used to map silicon distribution. Presence of trichomes, silica cells, and silica bodies were detected in silicon treated plants. Transcripts of CAD gene was also upregulated in these plants. Besides, phloroglucinol staining showed presence of lignified vascular bundles and sclerenchyma band. In conclusion, silicon treated rice plants showed an increase in lignin content, silicon content, and formation of silicified microstructures.
    Matched MeSH terms: X-Rays
  13. Fulltext Pulled/nursemaid's elbow
    Mohd Miswan MF, Othman MS, Muhamad Effendi F, Ibrahim MI, Rozali KN
    Malays Fam Physician, 2017;12(1):26-28.
    PMID: 28503271
    Nursemaid's elbow is a radial head subluxation caused by axial traction on the extended arm while the forearm is pronated, allowing for slippage of the radial head. A 2-year-old boy presented with pain, swelling and reduced range of movement of the right elbow for 4 days. The mother noted that the child was moving the right upper limb less often and there was tenderness over the right elbow. X-ray of the right elbow showed subluxation of the elbow joint with no obvious fracture. A trial of conservative management was decided upon and the patient was placed on a right elbow backslab with the right forearm in a supine position. On follow-up, there was no swelling, tenderness or neurological deficit noted. A repeate x-ray revealed normal findings.
    Matched MeSH terms: X-Rays
  14. Fulltext A case of missed giant bullae emphysema diagnosed as pneumothorax
    Ong, S.F., Nik Azlan, N.M.
    Medicine & Health, 2017;12(1):90-93.
    MyJurnal
    We report a case of a giant bullous emphysema misdiagnosed as a pneumothorax. A 18-year-old chronic smoker presented with right sided chest pain and dyspnoea. Initial respiratory rate was 35 /min, blood pressure was 136/90 mmHg, heart rate 80/min and SpO2 was 98% on room air. Clinical examination revealed reduced right air entry and left trachea deviation. Chest X-ray helped to arrive at a diagnosis of pneumothorax. Needle aspiration was then performed followed by a chest tube thoracostomy because of no improvement. Massive amount of blood was drained and patient deteriorated further. CT thorax revealed a right haemopneumothorax with multiple bullaes. Patient was rushed to OT for emergency thoracotomy for stapling of the ruptured bullae. Giant bullous emphysema can mimic pneumothorax and physician must be vigilant if draining a suspected pneumothorax.
    Keywords: emphysema, haemopneumothorax, thoracostomy, thorax
    Matched MeSH terms: X-Rays
  15. Fulltext Loculated transudative pleural effusion masquerading as right upper lobe consolidation in a haemodialysis patient
    Kho SS, Tay PS, Lee J, Tie ST
    AME Case Rep, 2017;1:4.
    PMID: 30263991 DOI: 10.21037/acr.2017.09.05
    Pleural effusion is a common encounter in renal failure patients and frequently possess a diagnostic challenge to clinician especially when it was exudative. Fortunately, transudative pleural effusion secondary to fluid overload remains the commonest cause of pleural effusion in haemodialysis patients. Frequent thoracocentesis enhance pleural inflammation and potentially complicate further this challenging clinical presentation. We report a middle-aged gentleman with advanced chronic kidney disease presented with dyspnea and new right upper lobe consolidation on chest roentograph. He had a history of recurrent bilateral pleural effusion secondary to fluid overload and hence multiple attempts of thoracocentesis were performed. Medical thoracoscopy performed previously yielded non-specific pleuritis. Flexible bronchoscopy demonstrates normal airway with negative microbiological studies. Computed tomography (CT) of the thorax shown a loculated hypodense pleural effusion at the apical region of the right upper lobe. Ultrasound guided thoracocentesis anteriorly yield 400 mL of clear straw color fluid which was transudative by Light's criteria. Post tapping chest X-ray shown complete resolution of right upper lobe consolidation and patient reports immediate relieve of dyspnea. Patient was started on regular effective haemodialysis and pleural effusion did not recur during follow up. Loculated pleural effusion masquerading as mediastinal tumour had been reported but pleural effusion that conformed to the contour of a lung lobe is rare. This case highlights the atypical but unique presentation of a transudative pleural effusion and demonstrates the risk of repeated thoracocentesis complicating a simple clinical presentation.
    Matched MeSH terms: X-Rays
  16. Fulltext Antimicrobial activities of silver nanoparticles bio-synthesized from diatom Amphora sp.
    Tevan, R., Govindaraju, Mugilan, Jayakumar, Saravanan, Govindan, Natanamurugaraj, Mohd Hasbi Ab. Rahim, Maniam, Gaanty Pragas, et al.
    Journal of Engineering and Science Research, 2017;1(2):176-184.
    MyJurnal
    A biological method was employed to synthesize silver nanoparticles through marine diatom Amphora sp. Antimicrobial efficacy test against different pathogenic bacteria were performed through synthesized silver nanoparticles. The physio-chemical properties of synthesized silver nanoparticles were studied using analytical techniques such as UV-Vis spectrophotometer, Field Emission Scanning Electron Microscopy (FESEM), EnergyDispersive X-ray Spectroscopy (EDX) and Fourier Transform Infrared Spectroscopy (FTIR) and X-ray Powder Diffraction (XRD). UV-Vis color intensity study and higher magnification of the Field Emission Scanning Electron Microscopy image showed the synthesized silver nanoparticles were rod shaped with a size range from 42 nm to 46 nm. The synthesized nanoparticles exhibited antibacterial activities in varying magnitudes. About 10 mg/ml of silver nanoparticles were able to inhibit the growth of gram-negative bacteria while gram-positive bacteria were resistant towards similar concentrations of silver nanoparticles.
    Matched MeSH terms: X-Rays
  17. Fulltext Characterization of COOH-Fe3O4/NCC-CTA+ on screen printed carbon electrode using field emission scanning electron microscope and energy dispersive X-Ray for DNA biosensor
    Che Engku Noramalina Che-Engku-Chik, Nor Azah Yusof, Jaafar Abdullah, Siti Sarah Othman, Helmi Wasoh
    Journal of Biochemistry, Microbiology and Biotechnology, 2017;5(2):19-21.
    MyJurnal
    A novel DNA biosensing platform was designed by the functionalization of iron oxide (Fe3O4)
    with the carboxylic group via capping agent, mercaptopropionic acid (MPA) and conjugated
    with nanocellulose crystalline (NCC) surface modified with surfactant cetyltrimethylammonium
    bromide (CTAB) to assist in the DNA sensing capability. The product of nanocomposites
    compound was drop-casted on screen printed carbon electrode (SPCE). Characterization by field
    emission scanning electron microscope (FESEM) and energy dispersive X-Ray (EDX)
    spectroscopy showing that carboxyl functionalized iron oxide (COOH-Fe3O4) can be hybridized
    with NCC-CTA+ via electrostatic interaction.
    Matched MeSH terms: X-Rays
  18. Study on the relation between mineral compositions of rock and construction characteristics of tunnel in cold regions: a case
    Yanliang shang, Shouji du, Honghong gao, Tongyin han
    Sains Malaysiana, 2017;46:2241-2250.
    Mineral composition of rock has a very important influence on the physical and mechanical properties of tunnel surrounding rock. Take Dangjianshan tunnel in cold regions for example, the rock specimens in different parts of tunnel were taken to carry out the detection test of mineral composition. By the detail qualitative and quantitative analysis, the relationship between mineral composition and surrounding rock engineering properties was explored. First of all, the composition and content of minerals contained in in the rock specimens were detected by X ray fluorescence spectrometer and X ray powder diffraction. The detection results show that rock of tunnel contains high hardness minerals such as quartz and feldspar which were proven by initial engineering geological investigation report, in addition, it also contains several kinds of low hardness minerals including inclined chlorite and illite which may exhibit large deformation characteristic of soft rock after the tunnel excavation in case of meeting water and weathering conditions. The total content of inclined chlorite and illite accounted for a considerable component in main tunnel, inclined shaft and parallel pilot respectively and the influence on surrounding rock engineering properties cannot be ignored. Therefore, mineral composition detection must be paid attention to after tunnel excavation. Secondly, the effects of mineral composition on surrounding rock were analyzed in aspects of rock strength, weathering resistance, water softening property and excavation deformation through comparing the rock samples in different parts of tunnel. The comparative results showed that when the mineral contents is high with high hardness and poor hydrophilicity, tunnel surrounding rock plays a better performance of physical and mechanical properties, vice versa. Finally, according to the specific geological and construction parameters of the tunnel, the correlation analysis was studied about the vault settlement after tunnel excavation and the hydrophilicity mineral content in main cave. The logarithmic relationship between them was found and the correlation coefficient was 0.98. It can provide a useful reference for the settlement prediction of Dangjinshan tunnel construction.
    Matched MeSH terms: X-Rays
  19. Fulltext Pulled/nursemaid’s elbow
    Mohd Miswan M. F., Mohamad Saifudin Othman, Ferdhany Muhamad Effendi, Khairul Nizam Rozali, Mohd Ikraam Ibrahim
    Malays Fam Physician, 2017;12(1):26-28.
    MyJurnal
    Nursemaid’s elbow is a radial head subluxation caused by axial traction on the extended arm while
    the forearm is pronated, allowing for slippage of the radial head. A 2-year-old boy presented with
    pain, swelling and reduced range of movement of the right elbow for 4 days. The mother noted that
    the child was moving the right upper limb less often and there was tenderness over the right elbow.
    X-ray of the right elbow showed subluxation of the elbow joint with no obvious fracture. A trial of
    conservative management was decided upon and the patient was placed on a right elbow backslab
    with the right forearm in a supine position. On follow-up, there was no swelling, tenderness or
    neurological deficit noted. A repeate x-ray revealed normal findings.
    Matched MeSH terms: X-Rays
  20. Enhanced Catalytic Activity, Facile Synthesis and Characterization Studies of Spinel Mn-Co Aluminate Nano-Catalysts
    Bhavani P, Manikandan A, Jaganathan SK, Shankar S, Antony SA
    J Nanosci Nanotechnol, 2018 Feb 01;18(2):1388-1395.
    PMID: 29448597 DOI: 10.1166/jnn.2018.14112
    Undoped and Mn2+ doped CoAl2O4 (MnxCo1-xAl2O4; x = 0.0 to 1.0) spinel nanoparticles were successfully synthesized by a microwave heating method using glycine as the fuel. X-ray powder diffraction (XRD) was confirmed the cubic spinel structure. The average crystallite size of the samples was found to be in the range of 16.46 nm to 20.25 nm calculated by Scherrer's formula. The nano-sized particle-like morphology of the samples was confirmed by high resolution scanning electron microscopy (HR-SEM) and transmission electron microscopy (HR-TEM) analysis. Energy dispersive X-ray (EDX) results showed the pure form of spinel aluminate structure. The band gap energy (Eg) of pure CoAl2O4 was estimated to be 3.68 eV from UV-Visible diffuse reflectance spectroscopy (DRS), and the Eg values increased with increase of Mn2+ ions, due to the smaller grain size. The magnetic hysteresis (M-H) loop showed the superparamagnetic nature, and the magnetization and coercivity values increased with increasing Mn2+ ions, which was confirmed by vibrating sample magnetometer (VSM). All compositions of the nano-catalysts were tested as catalyst successfully for the conversion of benzyl alcohol into benzaldehyde and observed good catalytic activity.
    Matched MeSH terms: X-Rays
Related Terms
Filters
Contact Us

Please provide feedback to Administrator (afdal@afpm.org.my)

External Links