Axillary malodor is caused by microbial biotransformation of non-smelling molecules present in apocrine secretions, into volatile odorous molecules. This study aimed to determine the antimicrobial activities of potassium aluminium salts (alum) against four malodor-producing axillary bacterial flora, as an alternative natural product for reducing axillary malodor.
This study utilized the incorporation of nanoparticle filler into an epoxy system to study the effect of different nanosized
montmorillonite (MMT) fillers on the thermal stability and mechanical properties of epoxy. The sample was prepared
using diglycidyl ether of bisphenol A (DGEBA) with different surface treatments of montmorillonite filler by mechanical
stirring. The results of thermal stability and mechanical properties of epoxy/clay system obtained from thermal gravimetric
analyzer (TGA), universal testing machine (UTM) and scanning electron microscopy (SEM) were discussed. With the same
amount of filler introduced into the system, different thermal stability of epoxy composite can be observed. Bentonite,
which contained other contaminant components, can downgrade the enhanced properties of the filler.
Porous γ-alumina is widely used as a catalyst carrier due to its chemical properties. These properties are strongly correlated with the physical properties of the material, such as porosity, density, shrinkage, and surface area. This study presents a technique that is less time consuming than other techniques to predict the values of the above-mentioned physical properties of porous γ-alumina via an artificial neural network (ANN) numerical model. The experimental data that was implemented was determined based on 30 samples that varied in terms of sintering temperature, yeast concentration, and socking time. Of the 30 experimental samples, 25 samples were used for training purposes, while the other five samples were used for the execution of the experimental procedure. The results showed that the prediction and experimental data were in good agreement, and it was concluded that the proposed model is proficient at providing high accuracy estimation data derived from any complex analytical equation.
Meiobenthos in Bidong Archipelago in coastal water of the South China Sea is hypothesised to have a certain trend of
distribution particularly in the island ecosystem where it is usually having different type of sea bottom. Nonetheless, since
it is located in a tropical area, the trend at the sub-tidal could be less obvious due to absent of clear season. Meiobenthic
sampling was carried out in Karah Island, an island in Bidong Archipelago, from the intertidal, towards the sub-tidal
zone covering the coral and non-coral area to see the trend in the density and composition. A transparent hand core
was used to collect benthos samples. Nematoda and harpacticoid copepods dominated the intertidal and sub-tidal zone
respectively. Harpacticoid copepods were higher in density in the non-coral sediment than the coral area. This could be
due to the high content of silt and clay in the coral area (2.98% of silt and clay). The 2-dimension MDS analysis on the
density data indicated the highest degree of scattering and an over-lapping condition for those intertidal and sub-tidal
samples respectively. ANOSIM result showed that the degree of similarity was lower at the intertidal (70%) than the subtidal
(reaching 90%) in the first sampling before both became no significant different in the second sampling. It could
indicate the stable condition in the subtidal than the intertidal ecosystem. The comparatively low density of meiobenthos
could indicate their response towards the environmental condition in the area which will only be confirmed by long term
ecological study.
Termites are found in various habitats, particularly diverse communities occurring in tropical forest and peatlands.
Termites are beneficial insects, which function as soil engineers, improving the soil quality. However, in peatlands
converted to commercial oil palm plantations, they are considered as pests. There is lack of studies on termite communities
in converted peatlands in Peninsular Malaysia. Thus, this study investigated termite species associated with oil palm
stands in three soil types (clay, shallow peat and deep peat) in Endau Rompin Plantation. The stand scouting method
was used to record the numbers and types of termites associated with palm trees in the individual stands on different
soil types. A total of 29 termite species associated with the palm stands were identified morphologically. All the species
belonged to the families Rhinotermitidae and Termitidae. Twenty-three of the 29 species were found in the shallow peat,
16 in clay soil and 15 in deep peat. The community structure was synthesized by two-way cluster analysis with Sorensen
(Bray Curtis) distance measure. Five termite groups associated with two soil types (clay soil and shallow/deep peat)
were generated. Moisture levels and organic content were likely to determine the presence of soil feeders identified in
the presence study. This study provides information on the status of termite species in oil palm plantation areas. Such
information may be useful in future planning strategies by the plantation management.
This study analyzes the heat transfer of a thin film flow on an unsteady stretching sheet in nanofluids. Three different types of nanoparticles are considered; copper Cu, alumina Al2O3 and titania TiO2 with water as the base fluid. The governing equations are simplified using similarity transformations. The resulting coupled nonlinear differential equations are solved by the Homotopy Analysis Method (HAM). The analytical series solutions are presented and the numerical results obtained are tabulated. In particular, it shows that the heat transfer rate decreases when nanoparticles volume fraction increases.
The ester sulfonate anionic surfactants are a potentially valuable class of sustainable surfactants. The micellar growth, associated rheological changes, and the onset of precipitation are important consequences of the addition of electrolyte and especially multi-valent electrolytes in anionic surfactants. Small angle neutron scattering, SANS, has been used to investigate the self-assembly and the impact of different valence electrolytes on the self-assembly of a range of ester sulfonate surfactants with subtly different molecular structures. The results show that in the absence of electrolyte small globular micelles form, and in the presence of NaCl, and AlCl3 relatively modest micellar growth occurs before the onset of precipitation. The micellar growth is more pronounced for the longer unbranched and branched alkyl chain lengths. Whereas changing the headgroup geometry from methyl ester to ethyl ester has in general a less profound impact. The study highlights the importance of relative counterion binding strengths and shows how the surfactant structure affects the counterion binding and hence the micelle structure. The results have important consequences for the response of such surfactants to different operational environments.
The K2NiF6 catalytic effect on the NaAlH4 dehydrogenation properties was studied in this work. The desorption temperature was studied using temperature-programmed desorption and exhibited a lower onset hydrogen release after doped with different wt % of K2NiF6 (5, 10, 15 and 20 wt %). It was found that the NaAlH4 doped with 5 wt % K2NiF6 showed the optimal value that can reduce the onset desorption temperature of about 160 °C compared to 190 °C for the milled NaAlH4. The NaAlH4 + 5 wt % K2NiF6 sample showed faster desorption kinetics where 1.5 wt % of hydrogen was released in 30 min at 150 °C. In contrast, the milled NaAlH4 only released about 0.2 wt % within the same time and temperature. From the Kissinger analysis, the apparent activation energy was 114.7 kJ/mol for the milled NaAlH4 and 89.9 kJ/mol for the NaAlH4-doped 5 wt % K2NiF6, indicating that the addition of K2NiF6 reduced the activation energy for hydrogen desorption of NaAlH4. It is deduced that the new phases of AlNi, NaF, and KH that were formed in situ during the dehydrogenation process are the key factors for the improvement of dehydrogenation properties of NaAlH4.
Hybrid reinforcement's novel composite (Al-Fe3O4-SiC) via powder metallurgy method was successfully fabricated. In this study, the aim was to define the influence of SiC-Fe3O4 nanoparticles on microstructure, mechanical, tribology, and corrosion properties of the composite. Various researchers confirmed that aluminum matrix composite (AMC) is an excellent multifunctional lightweight material with remarkable properties. However, to improve the wear resistance in high-performance tribological application, hardening and developing corrosion resistance was needed; thus, an optimized hybrid reinforcement of particulates (SiC-Fe3O4) into an aluminum matrix was explored. Based on obtained results, the density and hardness were 2.69 g/cm3, 91 HV for Al-30Fe3O4-20SiC, after the sintering process. Coefficient of friction (COF) was decreased after adding Fe3O4 and SiC hybrid composite in tribology behaviors, and the lowest COF was 0.412 for Al-30Fe3O4-20SiC. The corrosion protection efficiency increased from 88.07%, 90.91%, and 99.83% for Al-30Fe3O4, Al-15Fe3O4-30SiC, and Al-30Fe3O4-20SiC samples, respectively. Hence, the addition of this reinforcement (Al-Fe3O4-SiC) to the composite shows a positive outcome toward corrosion resistance (lower corrosion rate), in order to increase the durability and life span of material during operation. The accomplished results indicated that, by increasing the weight percentage of SiC-Fe3O4, it had improved the mechanical properties, tribology, and corrosion resistance in aluminum matrix. After comparing all samples, we then selected Al-30Fe3O4-20SiC as an optimized composite.
Aluminum (Al) is a standard material that has been used as a filter for ionising radiation however for polyvinyl chloride (PVC) there is no solid evidence to support but has been recommended. PVC has been selected as a potential filter material due to it is a long lasting constructing material and very durable, which can be used in a variety of application. The purpose of this study was to observe the effect of PVC on entrance surface dose (ESD) values as compare to the standard X-ray filter of Al. The effect of varying thickness of the materials and difference exposure settings were observed and compared to each other. From this study, the percentage difference for both PVC and Al thickness is less than ± 25.00 % shows that PVC has a potential to be used as one of the filter materials due to its ability to reduce the ESD value
The three dimensional free convection boundary layer flow near a stagnation point region is embedded in viscous nanofluid with the effect of g-jitter is studied in this paper. Copper (Cu) and aluminium oxide (Al2O3) types of water base nanofluid are cho- sen with the constant Prandtl number, Pr=6.2. Based on Tiwari-Das nanofluid model, the boundary layer equation used is converted into a non-dimensional form by adopting non- dimensional variables and is solved numerically by engaging an implicit finite-difference scheme known as Keller-box method. Behaviors of fluid flow such as skin friction and Nusset number are studied by the controlled parameters including oscillation frequency, amplitude of gravity modulation and nanoparticles volume fraction. The reduced skin friction and Nusset number are presented graphically and discussed for different values of principal curvatures ratio at the nodal point. The numerical results shows that, in- crement occurs in the values of Nusset number with the presence of solid nanoparticles together with the values of the skin friction. It is worth mentioning that for the plane stagnation point there is an absence of reduced skin friction along the y-direction where as for axisymmetric stagnation point, the reduced skin friction for both directions are the same. As nanoparticles volume fraction increased, the skin friction increased as well as the Nusset number. The results, indicated that skin frictions of copper are found higher than aluminium oxide.
Bauxite mining is not known to most Malaysian except recently due to environmental pollution issues in Kuantan, Pahang. Potential impacts are expected to go beyond physical environment and physical illness if the situation is not controlled. Loss of economic potentials, and the presence of unpleasant red dust causing mental distress, anger and community outrage. More studies are needed to associate it with chronic physical illness. While evidences are vital for action, merely waiting for a disease to occur is a sign of failure in prevention. All responsible agencies should focus on a wider aspect of health determinants rather than merely on the occurrence of diseases to act and the need to emphasize on sustainable mining to ensure health of people is not compromised.
Silicon, as the most important electronic material, has a lot of applications in the electronic industry and this includes the use of silicon in solar cells. One of the solar grade silicon production processes is the use of acid leaching for the removal of metallic impurities from silicon. The main advantage of this process for silicon purification is that it is based on a low temperature process. The purification of metallurgical grade silicon by acid leaching was studied as a function of time, temperature and etching. Based upon experimental results and under optimum conditions, it was possible to remove 41%, 71% and 25% of iron, calcium and aluminum respectively, with the use of aqua regia.
Compartmented Fluidized Bed Gasifier (CFBG), consisting of two compartments - the combustorand gasifier, uses air blown instead of pure oxygen for syngas production in bubbling fluidization mode, eliminating the need of air separation unit, and reducing the capital cost, thus distinguishes it from other traditional ones. Fluidization quality is a determining factor in the CFBG to guarantee its well-lifted behaviour. Previous study, without solid circulation at ambient conditions, brought to the fore the necessity of considering the effect of the minimum allowable effective diameter. The study was then performed in the CFBG cold physical model of 0.66m overall diameter (effective diameter for combustor and gasifier is 0.413m and 0.257m) to investigate the fluidization quality and compare it with the results obtained from the previous cold model of about 1.36 times smaller, but with the same compartmented ratio of 65:35. Different inert particles (river sand, quartz sand and alumina) were used, over a range of aspect ratios, for the aforementioned objective. The results showed that the fluidization quality in the gasifier has not been achieved and the degradation of fluidization quality in the combustor is still observed, notwithstanding the fact that the condition of the minimum allowable effective diameter has been met. The reduction of distributor free area, to increase the distributor pressure drop, showed a marginal effect on the quality. The effect of the minimum allowable effective diameter on fluidization quality in CFBG as well as the interplay of geometric and operational parameters require further studies be carried out. The fluidization quality of the binary mixture is also currently under investigation.
A systematic study to assess the concentration of radionuclides in primary coolant and associated water samples from the operation of a TRIGA Mark II reactor has been carried out. The samples were transferred into appropriate counting container and were counted by efficiency-calibrated gamma spectrometer systems for several hours to obtain statistically adequate data for qualitative and quantitative evaluation of the radioactive materials presence. The primary coolant was found to contain various gamma emitting radionuclides including 24Na, 41Ar, 42K, 51Cr, , 54Mn, 56Mn, 60Co, 99mTc, 122Sb, 124Sb and 187W. Most of the detected radionuclides were inferred to be originated from activation products of (n,) nuclear reactions of elements of reactor components such as stainless steel and aluminium alloy used in the reactor system. The study confirms the integrity of the reactor system with no apparent release of any fission products radionuclide into the coolant water system.
The adsorption equilibrium time and effects of pH and concentration of ¹⁴C-labeled chlorpyrifos
O,O-diethyl O-(3, 5, 6 trichloro-2-pyridyl)-phosphorothiote in soil were investigated. Two types of Malaysian soil under oil palm were used in this study; namely clay loam and clay soil obtained from the Sungai Sedu and Kuala Lumpur International Airport (KLIA) Estates, respectively. Equilibrium studies of chlorpyrifos between the agricultural soil and the pesticide solution were conducted. Adsorption equilibrium time was achieved within 6 and 24 hours for clay loam and clay soil, respectively. It was found that chlorpyrifos adsorbed by the soil samples was characterized by an initial rapid adsorption after which adsorption remained approximately constant. The percentage of ¹⁴C-labeled chlorpyrifos adsorption on soil was found to be higher in clay loam than in clay soils. Results of the study demonstrated that pH affected the adsorption of chlorpyrifos on both clay loam and clay soils. The adsorption of chlorpyrifos on both types of soil was higher at low pH with the adsorption reduced as the pH increased. Results also suggest that chlorpyrifos sorption by soil is concentration dependent.
The experiment aims to investigate the effect of high energy milling to the crystallite size of α-alumina. The starting material used is α-alumina powder with starting crystal size of 86nm. This powder was milled at different time ranges from 0 to 60 minutes and milling speed ranges from 400 rpm to 1100 rpm using a wet milling technique in corundum abrasive materials. The wet milling technique involved the use of water with the alumina to water ratio of 1:6.1. Samples prepared were then examined using the X-Ray Diffraction (XRD) to calculate the crystallite size and scanning electron microscope (SEM) was also used to determine changes in the morphology. Results from these analysis showed that the crystallite size will get smaller when milling speed and time of more than 600rpm and 30 minutes respectively were used. Optimum conditions to achieve the smallest crystal size of 79.7nm are 1000 rpm and 60 minutes.
Effects of organoclay concentration on the properties of radiation crosslinked natural rubber (NR)/ ethylene vinyl acetate (EVA)/clay nanocomposites were investigated. The NR/EVA blend with a ratio of 40/60 was melt blended with different concentration of either dodecyl ammonium montmorillonite (DDA-MMT) or dimethyl dihydrogenated tallow quarternary ammonium montmorillonite (C20A). Composite of NR/EVA blend with unmodified clay (Na-MMT) was also prepared for comparison purposes. The composites were irradiated with electron beam (EB) at an optimum irradiation dose. The formation of radiation-induced crosslinking depends on the type and concentration of the organoclay used in the preparation of nanocomposites as measured by gel content. Changes in the interlayer distance of the silicate layers with the increase of organoclay concentration were shown by the XRD results. Variation in the tensile properties of the nanocomposites with the increase of organoclay concentration depends on the formation of crosslinking as well as reinforcement effect of the organoclay. Improvement in thermal stability of the NR/EVA blend was also observed with the presence of organoclay.
The purpose of this study was to determine the adsorption coefficient (Koc) of chlorpyrifos in clay soil by measuring the Freundlich adsorption coefficient (Kads(f)) and desorption coefficient (1/n value) of chlorpyrifos. It was found that the Freundlich adsorption coefficient (Kads(f)) and the linear regression (r 2 ) of the Freundlich adsorption isotherm for chlorpyrifos in the clay soil were 52.6 L/kg and 0.5344, respectively. Adsoprtion equilibrium time was achieved within 24 hours for clay soil. This adsoprtion equilibrium time was used to determine the effect of concentration on adsorption. The adsorption coefficient (Koc) of clay soil was found to be 2783 L/kg with an initial concentration solution of 1 µg/g, soil-solution ratio (1:5) at 30 o C when the equilibrium between the soil matrix and solution was 24 hours. The Kdes decreased over four repetitions of the desorption process. The chlorpyrifos residues may be strongly adsorbed onto the surface of clay.
The long term objective of this research is to look into the possibility of replacing soil strength parameters such as cohesion and angle of friction with electrical resistivity value for the purpose of computing among others, factor of safety in slopes or bearing capacity of soil. This paper however is limited to the investigation of correlation between electrical resistivity with some selected soil parameters. Electrical resistivity tests, using a basic multi meter, steel moulds and other related equipment, were conducted in the laboratory on soil samples with variations in soil type, compaction energy and moisture content. The samples consisted of predominantly clay, silt and sandy size particles and were compacted in a 100 x 100 mm square mould, while the corresponding electrical resistivity tests were carried out using the disc electrode method in accordance to BS 1377. The values of the electrical parameters such as voltage, current and resistance, with the corresponding value of soil parameters such as cohesion, angle of friction and moisture content, were measured and recorded. The results of the tests produced some initial crude relationships between electrical resistivity and the selected soil parameters. The strongest correlation between electrical resistivity and angle of internal friction, φ, was obtained from the clay size samples with R2 of 0.824, while the maximum correlation between electrical resistivity and moisture content again was obtained through the clay samples with R2 of 0.818. From the other results and graphs analyzed, some consistencies and specific trends of behaviour observed gave some early indications that a more detail and precise correlation between electrical resistivity and soil strength parameters could be very well possible in future.