Ground water contain natural radioactivity associated with uranium and thorium that present naturally in rocks and soils. Humans may be exposed to the emission of energetic alpha particle from supported radon decaying process in this water when it is inhaled or ingested. Assessment of supported radon in ground water was carried out using fourteen ground water samples from Cameron Highlands. The measurement was accomplished by degassing the water samples using pump and then allowing the gas to flow into specially constructed 0.0191 m8 metal chamber. The activity concentration of supported radon in water sample was measured using continuous radon monitor inside the radon chamber. Measurement was carried out at one hour interval for twenty four hours. The hourly supported radon concentration was found to stabilize after about 8 hours. The stabilized concentration was used to determine supported radon activity concentration in the water samples. Results of the study show that depending on the sampling location, the activity concentrations of supported radon are in the range from 0.09 - 0.48 Bq/L which is lower than the activity concentration of radon in drinking water as proposed by USEPA (11 Bq/L).
Matched MeSH terms: Water Pollutants, Radioactive; Drinking Water
Land development, especially construction works, increase storm water volumes and pollution loads into rivers and lakes. The temporary drainage system at construction sites, particularly during the construction stage discharges a large amount of pollutants that can damage the aquatic system of the receiving water bodies. The potential of vegetative swale to alleviate this problem was evaluated. The size of the constructed vegetative swale was 7cm deep, 400cm long and 15cm wide at the bottom, and 17cm wide at the top. The experiment was conducted batch wise by filling the storage tank with the run-off water from the construction site. The water was allowed to flow through a pipe into the retention basin to maintain uniform flow before it entered the swale. The study showed that the run-off infiltrated through the soil at a rate of 489.6 mm/hr. Samples of surface run-off and infiltration water were collected at the end and the bottom of the swale. The results indicate that chemical oxygen demand (COD), total suspended solid (TSS), turbidity, iron and zinc were reduced by 85.4%, 80.8%, 36.4%, 52.8% and 96.0%, respectively, by surface flow and 91.1%, 98.8%, 58.2% 55.5% and 98.1%, respectively, by infiltration. Removal of nitrate and phosphorus by the planted vegetation was 69.4% and 21.1%, respectively, by infiltration. However, nutrient removal by surface flow was negligible. In conclusion, the vegetative swale was able to improve the water quality of the storm water run-off from the construction site from Class V to Class III, according to the Interim National Water Quality Standards for Malaysia.
A study to determine the influence of soil water status on the physiology of rice plant Oryza sativa var. MR220 after panicle initiation stage was carried out at Ladang Merdeka Mulong Lating in the Kemubu Agricultural Development Authority (KADA) area, Kelantan. Five water management treatments imposed on direct seeded rice were; T1. Continuous flooding, T2. Early flooding up to panicle initiation stage followed by saturated (F55-saturated), T3. Early flooding for the first month followed by saturated (F-30 saturated), T4. Continuous saturated, and T5. Continuous field capacity condition throughout the growth stage. The treatments were arranged in Randomized Complete Block Design (RCBD) with four replicates. In-situ stomatal conductance measurement was carried out at 68 DAS (days after seeding) and the elemental analysis of soil and plant samples was carried out using the Instrumental Neutron Activation Analysis (INAA). Results from this study showed significant differences between treatments for soil moisture content and plant moisture content, but no significance different in leaf stomatal conductance. Rice plant moisture, soil moisture and leaf stomatal conductance showed no interaction. Early flooding up to panicle initiation stage followed by saturated (T2: F55-saturated) resulted in higher plant moisture content. Soil plant transfer coefficient was highest in continuous saturated (T4) for nitrogen, early flooding for the first month followed by saturated (T3: F-30 saturated) for potassium, continuous field capacity condition throughout the growth stage (T5) for magnesium, and continuous flooding (T1) for sodium.
Gelatin from fish skin is known to be an alternative source for mammalian gelatin. However, it has weaker properties compared to bovine and porcine gelatin, which limits its use in the industry. The conventional method for fish gelatin extraction requires long production time and could cause serious water pollution and chemical treatments are often being used to enhance the yield of fish gelatin and its properties but it may affect the amino acid content of the gelatin. In this regard, High-Pressure Processing (HPP) is a novel method suggested for fish gelatin extraction. The HPP method is classified as green technology as it requires low electricity throughout the process. This study will discuss the impact of HPP the technique gelatin extracted from fish skin. Skins from four types of fish, namely red tilapia (Oreochromis niloticus), black tilapia (Oreochromis mossambicus), grouper (Epinephelus areolatus) and threadfin bream (Nemipterus tambuloides), were used. High pressure was applied at either pretreatment in citric acid solution or during thermal extraction; and the pressure was maintained at 250 MPa with pressure holding time of 10 minutes and 18 hours of water extraction. Gelatin extract from traditional acid-base method was prepared as a standard for comparison. The study found that there was an increment in the yield of gelatin and the concentration of gelatin extract, and the pre-treatment time was also reduced.
Among athletes, endurance is one of the key elements to victory. In addition to
training, athletes normally used supplement to prevent fatigue during the event. With
prolonged and intense activity, our body started to experience decrease in muscle
performance due to several factors such as oxidative stress, dehydration and
accumulation of lactic acid in the body fluids. The free radicals generated during
intense exercise will expose the cells to oxidative damages. In the event of
dehydration, there will be significant losses of water and functional electrolytes during
intense exercise which affected the body fluid balance. Fatigue will also occur during
reduced oxygen in aerobic metabolism which later caused accumulation of lactic acid
in the muscle. This will change the pH balance toward more acidic and caused the
muscles to lose contractile efficiency. In addition, fatigue can also be studied using rats
as model organism. Results from this activity can be useful to analyse cellular
metabolism and physiology effects of the tested rats toward physical exercise.
Therefore, this review aims to discuss the causes of fatigue through oxidative stress,
dehydration and lactic acid accumulation. In addition, the effectiveness of using rats as
a model system in measuring fatigue is also included in illustrating examples on fatigue
assessment in vivo.
Aqueous two-phase system (ATPS) has been suggested as a promising separation tool in the biotechnological industry. This liquid-liquid extraction technique represents an interesting advance in downstream processing due to several advantages such as simplicity, rapid separation, efficiency, economy, flexibility and biocompatibility. Up to date, a range of biotechnological products have been successfully recovered from different sources with high yield using ATPS-based strategy. In view of the important potential contribution of the ATPS in downstream processing, this review article aims to provide latest information about the application of ATPS in the recovery of various biotechnological products in the past 7 years (2010-2017). Apart from that, the challenges as well as the possible future work and outlook of the ATPS-based recovery method have also been presented in this review article.
The biomass concentration of conventional activated sludge (CAS) process due to low sludge sedimentation in clarifiers is limited to 3000 mg/L. In this study, high-frequency ultrasound wave (1.8 MHz) was applied to enhance the CAS process performance using high Mixed Liquor Suspended Solid (MLSS) concentration. The study conducted using a pilot scale CAS bioreactor (with and without ultrasound) and their performance for treating a hospital wastewater were compared. Experimental conditions were designed based on a Central Composite Design (CCD). The sets of data analyzed, modeled and optimized using Response Surface Methodology (RSM). The effect of MLSS concentration 3000-8000 mg/L and hydraulic retention time (HRT) 2-8 h are considered as operating variables to investigate on process responses. The obtained results showed that high-frequency ultrasound was significantly decreased the sludge volume index (SVI) 50% and effluent turbidity about 88.5% at high MLSS. Also, observed that COD removal of both systems was nearly similar, as the maximum COD removal for sonicated and non-sonicated systems were 92 and 92.5% respectively. However, this study demonstrates that the ultrasound irradiation has not had any negative effect on the microbial activity.
In this study, carbon species were grown on the surface of Ni-impregnated powder activated carbon to form a novel hybrid carbon nanomaterial by chemical vapor deposition. The carbon nanomaterial was obtained by the precipitation of the methane elemental carbon atoms on the surface of the Ni catalyst. The physiochemical properties of the hybrid material were characterized to illustrate the successful growth of carbon species on the carbon substrate. The response surface methodology was used for the evaluation of adsorption parameters effect such as pH, adsorbent dose and contact time on the percentage removal of MB dye from aqueous solution. The optimum conditions were found to be pH = 11, adsorbent dose = 15 mg and contact time of 120 min. The material we prepared showed excellent removal efficiency of 96% for initial MB concentration of 50 mg/L. The adsorption of MB was described accurately by the pseudo-second-order model with R2 of 0.998 and qe of 163.93 (mg/g). The adsorption system showed the best agreement with Langmuir model with R2 of 0.989 and maximum adsorption capacity (Qm) of 250 mg/g.
Matched MeSH terms: Water Pollutants, Chemical/chemistry*
Deforestation, climate change and invasive species constitute three global threats to biodiversity that act synergistically. However, drivers and rates of loss of freshwater biodiversity now and in the future are poorly understood. Here we focus on the potential impacts of global change on freshwater mussels (Order Unionida) in Sundaland (SE Asia), a vulnerable group facing global declines and recognized indicators of overall freshwater biodiversity. We used an ensemble of distribution models to identify habitats potentially suitable for freshwater mussels and their change under a range of climate, deforestation and invasion scenarios. Our data and models revealed that, at present, Sundaland features 47 and 32 Mha of habitat that can be considered environmentally suitable for native and invasive freshwater mussels, respectively. We anticipate that by 2050, the area suitable for palm oil cultivation may expand between 8 and 44 Mha, representing an annual increase of 2-11%. This is expected to result in a 20% decrease in suitable habitat for native mussels, a drop that reaches 30% by 2050 when considering concomitant climate change. In contrast, the habitat potentially suitable for invasive mussels may increase by 44-56% under 2050 future scenarios. Consequently, native mussels may compete for habitat, food resources and fish hosts with invasive mussels across approximately 60% of their suitable range. Our projections can be used to guide future expeditions to monitor the conservation status of freshwater biodiversity, and potentially reveal populations of endemic species on the brink of extinction. Future conservation measures-most importantly the designation of nature reserves-should take into account trends in freshwater biodiversity generally, and particularly species such as freshwater mussels, vital to safeguard fundamental ecosystem services.
A combination between the nanostructured photocatalyst and cellulose-based materials promotes a new functionality of cellulose towards the development of new bio-hybrid materials for various applications especially in water treatment and renewable energy. The excellent compatibility and association between nanostructured photocatalyst and cellulose-based materials was induced by bio-combability and high hydrophilicity of the cellulose components. The electron rich hydroxyl group of celluloses helps to promote superior interaction with photocatalyst. The formation of bio-hybrid nanostructured are attaining huge interest nowadays due to the synergistic properties of individual cellulose-based material and photocatalyst nanoparticles. Therefore, in this review we introduce some cellulose-based material and discusses its compatibility with nanostructured photocatalyst in terms of physical and chemical properties. In addition, we gather information and evidence on the fabrication techniques of cellulose-based hybrid nanostructured photocatalyst and its recent application in the field of water treatment and renewable energy.
Lignin extracted from oil palm fronds (OPF) underwent chemical modification by incorporating m-cresol into the lignin matrix. This study reports on the physicochemical properties and antioxidant activity of unmodified autohydrolyzed ethanol organosolv lignin (AH EOL) and the modified autohydrolyzed ethanol organosolv lignin (AHC EOL). The lignin samples were analyzed by FTIR, 1H and 13C NMR spectroscopy, 2D NMR: HSQC spectroscopy, CHN analysis, molecular weight distribution analysis; GPC and thermal analysis; DSC and TGA. The lignin modification has reduced the hydrophobicity of its complex structure by providing better quality lignin with smaller fragments and higher solubility rate in water (DAHCEOL: 42%>DAHEOL: 25%). It was revealed that the modification of lignin has improved their structural and antioxidant properties, thus venture their possible applications.
Electrocoagulation (EC) is employed to investigate the energy consumption (EnC) of synthetic wastewater. In order to find the best process conditions, the influence of various parameters including initial pH, initial dye concentration, applied voltage, initial electrolyte concentration, and treatment time are investigated in this study. EnC is considered the main criterion of process evaluation in investigating the effect of the independent variables on the EC process and determining the optimum condition. Evolutionary polynomial regression is combined with a multi-objective genetic algorithm (EPR-MOGA) to present a new, simple and accurate equation for estimating EnC to overcome existing method weaknesses. To survey the influence of the effective variables, six different input combinations are considered. According to the results, EPR-MOGA Model 1 is the most accurate compared to other models, as it has the lowest error indices in predicting EnC (MARE = 0.35, RMSE = 2.33, SI = 0.23 and R2 = 0.98). A comparison of EPR-MOGA with reduced quadratic multiple regression methods in terms of feasibility confirms that EPR-MOGA is an effective alternative method. Moreover, the partial derivative sensitivity analysis method is employed to analyze the EnC variation trend according to input variables.
Nitrate is required to maintain the growth and metabolism of plant and animals. Nevertheless, in excess amount such as polluted water, its concentration can be harmful to living organisms such as microalgae. Recently, studies on microalgae response towards nutrient fluctuation are usually limited to lipid accumulation for the production of biofuels, disregarding the other potential of microalgae to be used in wastewater treatments and as source of important metabolites. Our study therefore captures the need to investigate overall metabolite changes via NMR spectroscopy approach coupled with multivariate data to understand the complex molecular process under high (4X) and low (1/4X) concentrations of nitrate ([Formula: see text]). NMR spectra with the aid of chemometric analysis revealed contrasting metabolites makeup under abundance and limited nitrate treatment. By using NMR technique, 43 types of metabolites and 8 types of fatty acid chains were detected. Nevertheless, only 20 key changes were observed and 16 were down regulated in limited nitrate condition. This paper has demonstrated the feasibility of NMR-based metabolomics approach to study the physiological impact of changing environment such as pollution to the implications for growth and productivity of microalgae population.
The world water resources are contaminated due to discharge of a large number of pollutants from industrial and domestic sources. A variety of a single and multiple units of physical, chemical, and biological processes are employed for pollutants removal from wastewater. Adsorption is the most widely utilized process due to high efficiency, simple procedure and cost effectiveness. This paper reviews the research work carried out on the use of geopolymer materials for the adsorption of heavy metals and dyes. Geopolymers possess good surface properties, heterogeneous microstructure and amorphous structure. The performance of geopolymers in the removal of heavy metals and dyes is reported comparable to other materials. The pseudo-second order kinetics and Langmuir isotherm models mostly fit to the adsorption data suggesting homogeneous distribution of adsorption sites with the formation of monolayer adsorbate on the surface of geopolymers. Adsorption of heavy metals and dyes onto geopolymers is spontaneous, endothermic and entropy driven process. Future research should focus on the enhancement of geopolymer performance, testing on pollutants other than heavy metals and dyes, and verification on real wastewater in continuous operation.
Matched MeSH terms: Water Pollutants, Chemical; Waste Water
This study investigated the occurrence of nine pharmaceuticals (amoxicillin, caffeine, chloramphenicol, ciprofloxacin, dexamethasone, diclofenac, nitrofurazone, sulfamethoxazole, and triclosan) and to evaluate potential risks (human health and ecotoxicological) in Lui, Gombak and Selangor (Malaysia) rivers using commercial competitive Enzyme-Linked Immunosorbent Assay (ELISA) kit assays. Physicochemical properties of these rivers showed the surface samples belong to Class II of Malaysian National Water Quality Standards which requires conventional treatment before consumption. All the pharmaceuticals were detected in all three rivers except for triclosan, dexamethasone and diclofenac which were not detected in few of sampling locations in these three rivers. Highest pharmaceutical concentrations were detected in Gombak river in line of being as one of the most polluted rivers in Malaysia. Ciprofloxacin concentrations were detected in all the sampling locations with the highest at 299.88 ng/L. While triclosan, dexamethasone and diclofenac concentrations were not detected in a few of sampling locations in these three rivers. All these nine pharmaceuticals were within the levels reported previously in literature. Pharmaceutical production, wastewater treatment technologies and treated sewage effluent were found as the potential sources which can be related with pharmaceuticals occurrence in surface water samples. Potential human risk assessment showed low health risk except for ciprofloxacin and dexamethasone. Instead, ecotoxicological risk assessment indicated moderate risks were present for these rivers. Nevertheless, results confirmation using instrumental techniques is needed for higher degree of specificity. It is crucial to continuously monitor the surface water bodies for pharmaceuticals using a cost-effective prioritisation approach to assess sensitive sub-populations risk.
Matched MeSH terms: Water Pollutants, Chemical/analysis*
Dissolved oil palm empty fruit bunch (EFB) cellulose in NaOH/urea solvent was mixed with sodium carboxymethylcellulose (NaCMC) to form a green regenerated superabsorbent hydrogel. The effect of concentration of epichlorohydrin (ECH) as the crosslinker on the formation, physical, and chemical properties of hydrogel was studied. Rapid formation and higher gel content of hydrogel were observed at 10% concentration of ECH. The superabsorbent hydrogel was successfully fabricated in this study with the swelling ability >100,000%. Hydrogel with higher concentration of ECH showed opposite trend by having higher superabsorbent property than that of lower concentration. The covalent bond of COC was observed with Attenuated total reflectance fourier transform infrared (ATR-FT-IR) spectroscopy to confirm the occurrence of crosslinking. The physical and chemical properties of hydrogel were affected by swelling phenomenon. Hydrogel with higher degree of swelling exhibited lower moisture retention and higher transparency. Moreover, the weight of the superabsorbent hydrogel increased with the decrement of pH value of external media (distilled water). This study provided substantial information on the effect of different percentage of ECH as crosslinker on hydrogel basic properties. Furthermore, this study affords correlation of many essential driving forces that affected hydrogel superabsorbent property.
Hydrothermal carbonization of biomass wastes presents a promising step in the production of cost-effective activated carbon. In the present work, mesoporous activated carbon (HAC) was prepared by the hydrothermal carbonization of rattan furniture wastes followed by NaOH activation. The textural and morphological characteristics, along with adsorption performance of prepared HAC toward methylene blue (MB) dye, were evaluated. The effects of common adsorption variables on performance resulted in a removal efficiency of 96% for the MB sample at initial concentration of 25mg/L, solution pH of 7, 30°C, and 8h. The Langmuir equation showed the best isotherm data correlation, with a maximum uptake of 359mg/g. The adsorbed amount versus time data was well fitted by a pseudo-second order kinetic model. The prepared HAC with a high surface area of 1135m(2)/g and an average pore size distribution of 35.5Å could be an efficient adsorbent for treatment of synthetic dyes in wastewaters.