The aim of this work was the synthesis of a novel hydroxyl-fatty acid derivative of kojic acid rich in kojic acid monoricinoleate (KMR) which can be widely used in the cosmetic and food industry. The synthesis of KMR was carried out by lipase-catalysed esterification of ricinoleic and kojic acids in solvent-free system. Three immobilized lipases were tested and the best KMR yields were attained with Lipozyme TL IM and Novozym 435. Since Lipozyme TL IM is the cheapest, it was selected to optimize the reaction conditions. The optimal reaction conditions were 80 °C for the temperature, 1:1 for the alcohol/acid molar ratio, 600 rpm for stirring speed and 7.8% for the catalyst concentration. Under these conditions, the reaction was scaled up in a 5×10⁻³ m³ stirred tank reactor. ¹H-¹³C HMBC-NMR showed that the primary hydroxyl group of kojic acid was regioselectively esterified. The KMR has more lipophilicity than kojic acid and showed antioxidant activity that improves the oxidation stability of biodiesel.
Novel series of 2-(4,6-dimethoxy,1,3,5-triazin-2-yl) amino acid ester derivatives were synthesized using simple one pot method in methanol. The products were obtained in high yields and purities as observed from their spectral data, elemental analyses, GC-MS and X-ray crystallographic analysis. The B3LYP/6-311G(d,p) calculated molecular structures are well correlated with the geometrical parameters obtained from the X-ray analyses. The spectroscopic properties such as IR vibrational modes, NMR chemical shifts and UV-Vis electronic transitions were discussed both experimentally and theoretically. The IR vibrational frequencies showed good correlations with the experimental data (R(2)=0.9961-0.9995). The electronic spectra were assigned based on the TD-DFT results. Intense electronic transition band is calculated at 198.1nm (f=0.1389), 204.2nm (f=0.2053), 205.0 (f=0.1704) and 205.7 (0.2971) for compounds 6a-i, respectively. The molecular orbital energy levels contributed in the longest wavelength transition band were explained. For all compounds, the experimental wavelengths showed red shifts compared to the calculations due to the solvent effect. The NMR chemical shifts were calculated using GIAO method. The NBO analyses were performed to predict the stabilization energies due to the electron delocalization processes occur in the studied systems.
Asparagus officinalis as a valuable medicinal plant has a low multiplication rate using the conventional methods. This study was carried out to establish an efficient in vitro propagation protocol and also to compare some biological activities of in vivo and in vitro grown Asparagus. The nodal explants were cultured on MS medium supplemented with different concentrations of 6-benzylaminopurine (BAP) and 1-Naphthaleneacetic acid (NAA) or kinetin (Kn) and Indolebutyric acid (IBA), under light and dark conditions. After 6 weeks of culture, the highest percentage (100%) of callus formation was found in 17 of treatments under dark condition and 3 treatments under light condition. Also between the two groups of hormones, Kn +IBA showed better results in promoting callus formation. The highest average number of shoots (4.25) of size 4 mm or more per explant, formed under dark condition using 1.5 mg/L BAP mixed with 0.05 mg/L NAA. Rooting was best induced in shoots excised from shoot cultures which were proliferated on MS medium supplemented with an optimal concentration of 0.4 mg/L IBA (2 roots per explant). In the second part of the study, the extracts of in vivo and in vitro grown plants as well as callus tissue were tested for their total phenolic and flavonoid content, antioxidant and antityrosinase activities, using two different extraction solvents (methanol and hexane). The methanol extract of in vivo grown plants showed a significantly higher amount of total phenolic and flavonoid content. The antioxidant activity of tested samples followed this order; in vivo plant > callus > in vitro plant.
Lignocellulosic biomass contains lignin, an aromatic and oxygenated substance and a potential method for lignin utilization is achieved through catalytic conversion into useful phenolic and aromatic monomers. The application of monometallic catalysts for lignin hydrogenolysis reaction remains one of the major reasons for the underutilization of lignin to produce valuable chemicals. Monometallic catalysts have many limitations such as limited catalytic sites for interacting with different lignin linkages, poor catalytic activity, low lignin conversion, and low product selectivity. It is due to lack of synergy with other metallic catalysts that can enhance the catalytic activity, stability, selectivity, and overall catalytic performance. To overcome these limitations, works on the application of bimetallic catalysts that can offer higher activity, selectivity, and stability have been initiated. In this review, cutting-edge insights into the catalytic hydrogenolysis of lignin, focusing on the production of phenolic and aromatic monomers using bimetallic catalysts within an internal hydrogen donor solvent are discussed. The contribution of this work lies in a critical discussion of recent reported findings, in-depth analyses of reaction mechanisms, optimal conditions, and emerging trends in lignin catalytic hydrogenolysis. The specific effects of catalytic active components on the reaction outcomes are also explored. Additionally, this review extends beyond current knowledge, offering forward-looking suggestions for utilizing lignin as a raw material in the production of valuable products across various industrial processes. This work not only consolidates existing knowledge but also introduces novel perspectives, paving the way for future advancements in lignin utilization and catalytic processes.
According to the 12 principles of green chemistry, surface functionalization was performed using glutaric anhydride under solvent-free and catalyst-free conditions. FTIR spectra and DS analyses demonstrated the functionalization of HCl-hydrolyzed cellulose. The influence of two parameters, i.e., the glutaric anhydride concentration and the reaction time, on the functionalization of HCl-hydrolyzed cellulose was investigated. Protocol efficiency was studied by a degree of substitution (DS). It was found that higher concentrations of glutaric anhydride cause an enhancement of DS to 0.75 and 0.87 for GA3-12 and GA9-12, respectively. In addition, the longer reaction time increased zeta potential from -12.2 ± 1.7 for G9-6 to -34.57 ± 2.2 for GA9-12. Morphology analysis by SEM showed a decrease in fiber length for the functionalized cellulose. DSC profiles confirmed dehydration at a range of 17 to 134 °C. A glass transition was revealed at -30 to -20 °C for all studied samples. The fusion, the depolymerization of cellulose chains, the cleavage of glycosidic linkages, and the decomposition of the crystalline parts of cellulose occur at 195 to 374 °C. Therefore, an efficient and greener process was developed to functionalize the HCl-hydrolyzed cellulose by glutaric anhydride, a safe and non-toxic anhydride, in the absence of the solvent and catalyst.
Dihexyl-sexithiophene (DH6T) was doped with tris (8-hydroxyquinolinate) aluminum (Alq3) to prepare blends of DH6T/ Alq3 by dissolving the mixture in the chloroform/hexane co-solvent. Solid films with different thickness deposited on quartz substrates were obtained from the blends via casting process. Optical absorption spectroscopy has been performed to measure the optical band gap of pure and doped DH6T as well as variations in the band gap with dopant concentration (weight %). This variation in optical band gap with dopant concentration was determined quantitatively with fitted and extrapolated techniques and observed qualitatively from the red shift appeared along the optical absorption spectra. The results showed that within a specific dopant content, the optical energy gap, Eg of DH6T decreases from 2.69 eV to 1.8 eV with increasing dopant concentration to 23.1%.
Biofouling on the membrane surface leads to performance deficiencies in membrane filtration. In this study, the application of ginger extract as a bio-based additive to enhance membrane antibiofouling properties was investigated. The extract was dispersed in a dimethyl acetamide (DMAc) solvent together with polyvinylidene fluoride (PVDF) to enhance biofouling resistance of the resulting membrane due to its antibiotic property. The concentrations of the ginger extract in the dope solution were varied in the range of 0-0.1 wt %. The antibacterial property of the resulting membranes was assessed using the Kirby Bauer disc diffusion method. The results show an inhibition zone formed around the PVDF/ginger membrane against Escherichia coli and Staphylococcus aureus demonstrating the efficacy of the residual ginger extract in the membrane matrix to impose the antibiofouling property. The addition of the ginger extract also enhanced the hydrophilicity in the membrane surface by lowering the contact angle from 93° to 85°, which was in good agreement with the increase in the pure water flux of up to 62%.
Polyhydroxyalkanoate (PHA) copolymers show a relatively higher in vivo degradation rate compared to other PHAs, thus, they receive a great deal of attention for a wide range of medical applications. Nanoparticles (NPs) loaded with poorly water-soluble anticancer drug docetaxel (DCX) were produced using poly(3-hydroxybutyrate-co-4-hydroxybutyrate), P(3HB-co-4HB), copolymers biosynthesised from Cupriavidus malaysiensis USMAA1020 isolated from the Malaysian environment. Three copolymers with different molar proportions of 4-hydroxybutirate (4HB) were used: 16% (PHB16), 30% (PHB30) and 70% (PHB70) 4HB-containing P(3HB-co-4HB). Blank and DCX-loaded nanoparticles were then characterized for their size and size distribution, surface charge, encapsulation efficiency and drug release. Preformulation studies showed that an optimised formulation could be achieved through the emulsification/solvent evaporation method using PHB70 with the addition of 1.0% PVA, as stabilizer and 0.03% VitE-TPGS, as surfactant. DCX-loaded PHB70 nanoparticles (DCX-PHB70) gave the desired particle size distribution in terms of average particle size around 150 nm and narrow particle size distribution (polydispersity index (PDI) below 0.100). The encapsulation efficiency result showed that at 30% w/w drug-to-polymer ratio: DCX- PHB16 NPs were able to encapsulate up to 42% of DCX; DCX-PHB30 NPs encapsulated up to 46% of DCX and DCX-PHB70 NPs encapsulated up to 50% of DCX within the nanoparticle system. Approximately 60% of DCX was released from the DCX-PHB70 NPs within 7 days for 5%, 10% and 20% of drug-to-polymer ratio while for the 30% and 40% drug-to-polymer ratios, an almost complete drug release (98%) after 7 days of incubation was observed.
We examined the anti-acanthamoebic efficacy of green tea Camellia sinensis solvent extract (SE) or its chemical constituents against Acanthamoeba castellanii by using anti-trophozoite, anti-encystation, and anti-excystation assays. C. sinensis SE (625-5000 µg/mL) inhibited trophozoite replication within 24-72 h. C. sinensis SE exhibited a dose-dependent inhibition of encystation, with a marked cysticidal activity at 2500-5000 µg/mL. Two constituents of C. sinensis, namely epigallocatechin-3-gallate and caffeine, at 100 μM and 200 μM respectively, significantly inhibited both trophozoite replication and encystation. Cytotoxicity analysis showed that 156.25-2500 µg/mL of SE was not toxic to human corneal epithelial cells, while up to 625 µg/mL was not toxic to Madin-Darby canine kidney cells. This study shows the anti-acanthamoebic potential of C. sinensis SE against A. castellanii trophozoites and cysts. Pre-clinical studies are required to elucidate the in vivo efficacy and safety of C. sinensis SE.
Recent years, great interest has been devoted to the conversion of biomass-derived carbohydrate into sugars, such as glucose, mannose and fructose. These are important versatile intermediate products that are easily processed into high value-added biofuels. In this work, microwave-assisted dilute sulfuric acid hydrolysis of deproteinated palm kernel cake (DPKC) was systematically studied using Response Surface Methodology. The highest mannose yield (92.11%) was achieved at the optimized condition of 148°C, 0.75N H2SO4, 10min 31s and substrate to solvent (SS) ratio (w/v) of 1:49.69. Besides that, total fermentable sugars yield (77.11%), was obtained at 170°C, 0.181N H2SO4, 6min 6s and SS ratio (w/v) of 1:40. Ridge analysis was employed to further verify the optimum conditions. Thus, this work provides fundamental data of the practical use of DPKC as low cost, high yield and environmental-friendly material for the production of mannose and other sugars.
Solvolysis of oil palm empty fruit bunches (EFB) fibres using different solvents (acetone, ethylene glycol (EG), ethanol, water and toluene) were carried out using an autoclave at 275°C for 60 min. The solvent efficiency in term of conversion yield was found to be: EG>water>ethanol>acetone>toluene. The liquid products and residue obtained were analyzed using Fourier transform infrared spectroscopy (FTIR) and gas chromatography/mass selectivity. The obtained results showed that the chemical properties of the oil product were significantly affected by the type of solvent used for the solvolysis process. The higher heating value (HHV) of oil products obtained using ethanol is ∼29.42 MJ/kg, which is the highest among the oil products produced using different solvents. Water, ethanol and toluene yield major phenolic compounds. While EG favors the formation of alcohol compounds and acetone yields ketone and aldehyde compounds.
Thin films of cerium oxide (CeO2) were prepared on silicon (Si) substrate by metal organic decomposition route. 0.25 M of cerium (III) acetylacetonate (acac) was used as starting materials with the addition of methanol and acetic acid as solvents. Oxide conversion of the film by thermal treatment was conducted at temperature ranging from 400 o C to 1000 o C for 15 min in argon ambient. X-ray diffraction (XRD) analysis utilizing Cukα radiation (Model Brukker’s Diffrac Plus ), Filmetrics system measurement, field emission scanning electron microscope (FE-SEM) (Model Zeiss Supra 35VP FE-SEM) and atomic force microscopy (AFM) (Model SII Nanonavi) were employed to characterize the phase formed and morphologies of the film produced.
Antioxidants in seaweeds have attracted increasing interest for its role in protecting human health. Therefore, the aim of this study was to assess the Total phenolic content (TPC) values and antioxidant activities in red seaweeds Kappaphycus alvarezii and Kappaphycus striatum of different solvent extracts. Total phenolic content (TPC) and antioxidant activities (DPPH scavenging assay and Trolox equivalent antioxidant capacity assay, TEAC) for both K. alvarezii and K. striatum extracts were determined using different solvents at different concentrations (ethanol: 50%, 70%, 100%; acetone: 50%, 70%, 100%; methanol: 50%, 70%, 100%). The TPC value was measured using the Folin-Ciocalteu’s method. The antioxidant activities were measured by 2, 2-diphenyl-1-picrylhydrazyl (DPPH) free radical scavenging assay and Trolox Equivalent Antioxidant Capacity (TEAC) assay. The highest TPC value of K. alvarezii antioxidant extract was obtained by 50% ethanol extracts while for K. striatum obtained by 50% methanol extract. The highest percentage of DPPH free radical inhibition for K. alvarezii was shown by 50% acetone extract while K. striatum was shown using 50% methanol extract. The highest TEAC value for K. alvarezii was shown by 50% acetone while K. striatum extract was shown by 50% ethanol extract. The TPC values and antioxidant activities of all solvent extracts of K. striatum were significantly higher (p< 0.05) than K. alvarezii antioxidant extracts. The TPC values showed strong correlation (r = 0.797) with TEAC values for K. alvarezii antioxidant extract (p< 0.01). The TEAC values also showed strong correlation (r = 0.735) with percentage of DPPH free radical inhibition for K. alvarezii (p< 0.01). The TPC value, DPPH free radical scavenging assay and TEAC assay for K. striatum extracts showed strong correlation (r> 0.8) with each other (p< 0.01). In summary, K. striatum showed better antioxidant activity and higher TPC value than K. alvarezii.
owder injection molding (PIM) is able to produce porous titanium alloy/hydroxyapatite composite through the space holder technique. Thermal debinding and sintering processes were the main challenges due to different properties of metal and ceramic in producing such composite. This study focused on the effect of different space holders on the physical and mechanical properties of debound and sintered porous titanium aloi/hydroxyapatite composite. The feedstock is containing of 80 wt. % of titanium alloy/hydroxyapatite with 20 wt. % of space holders such as sodium chloride (NaCl) and polymethylmethacrylate (PMMA), respectively. The binders were then removed from the injected samples by two stages of debinding; solvent and thermal debinding. The sintering was performed at three different temperatures 1100oC, 1200oC and 1300oC at a heating rate of 10oC /min and holding time of 5 h. It was found that the samples containing PMMA space holder was fractured after sintering. While, the samples containing NaCl space holder successfully formed pores and not fractured. At sintering temperature of 1300oC, the density, compressive strength and porosity volume percentages for the sintered sample containing NaCl space holder were 3.05 g/cm3, 91.7 MPa. and 11.9 vol%, respectively.
Ascorbic acid or vitamin C is mostly found in natural products such as fruits and vegetables. High performance liquid chromatography (HPLC) method has been developed and validated to compare the ascorbic acid content in Benincasa hispida (Bh) fruit extract with three different extraction solvents; i) 3% metaphosphoric acid, ii) 3% citric acid and iii) distilled water. The compound has been detected and quantified by the use of HPLC coupled with UV-Vis detector. The amount of ascorbic acid detected in Bh fruit extract prepared with different extraction solvents; 3% metaphosphoric acid, 3% citric acid and distilled water were 13.18, 7.91 and 9.42 mg/100g respectively. Total run time was 6 min and the retention time was 2.60 min. Calibration curve was linear with the concentration range 1.00 – 16.00 μg/ml. Limits of detection was 0.24 μg/ml, limit of quantification was 0.81 μg/ml and recovery was 93.52%. The result showed ascorbic acid content is higher in Bh fruit extract with 3% metaphosphoric acid, followed by extract with distilled water and 3% citric acid. Thus, Bh is another novel fruit/ vegetable potentially used as food ingredient as it contains a good source of ascorbic acid that can be good for one’s health.
In the present work, supercritical fluid extraction (SFE) with CO2 as solvent and EtOH/water (v/v) as co-solvent was optimised by applying 23 factorial experimental design for the extraction of betacyanins from red pitaya fruit (Hylocereus polyrhizus) peel. Three independent variables of pressure (20-30 MPa), temperature (40-60°C) and co-solvent concentration (10-20%) were chosen for response variables. With the 2 mL/min flow rate of CO2, the dynamic time of extraction was found to be 90 min. The linear effects of main factors and interactions were evaluated. The calculated response surface model for the pressure/temperature was found to be significant for all the dependent variables. At optimal condition of SFE, the response variables were assessed as maximum extraction yield of 4.09 ± 0.69%, total betacyanins content of 25.49 ± 1.54 mg/100 mL, redness (a*) of 58.18 ± 0.82, and IC50 (antioxidant activity) of 1.34 ± 0.12 mg/mL for the experimental peel extracts. The optimal levels of independent variables were validated for the experimental responses as predicted by the mathematical model. The reliability of this method was confirmed as there was no significant difference between experimental and predicted values. The HPLC-MS profile of betacyanins extract comprised of both acylated and non-acylated betacyanins constituents.
Multi-walled carbon nanotubes (CNTs) functionalized with a deep eutectic solvent (DES) were utilized to remove mercury ions from water. An artificial neural network (ANN) technique was used for modelling the functionalized CNTs adsorption capacity. The amount of adsorbent dosage, contact time, mercury ions concentration and pH were varied, and the effect of parameters on the functionalized CNT adsorption capacity is observed. The (NARX) network, (FFNN) network and layer recurrent (LR) neural network were used. The model performance was compared using different indicators, including the root mean square error (RMSE), relative root mean square error (RRMSE), mean absolute percentage error (MAPE), mean square error (MSE), correlation coefficient (R2) and relative error (RE). Three kinetic models were applied to the experimental and predicted data; the pseudo second-order model was the best at describing the data. The maximum RE, R2 and MSE were 9.79%, 0.9701 and 1.15 × 10-3, respectively, for the NARX model; 15.02%, 0.9304 and 2.2 × 10-3 for the LR model; and 16.4%, 0.9313 and 2.27 × 10-3 for the FFNN model. The NARX model accurately predicted the adsorption capacity with better performance than the FFNN and LR models.
This study reports the caffeine content in seven locally available coffee. The caffeine was extracted with chloroform and analysed using Fourier Transform Infrared (FTIR). The method reports an average recovery of 101% with the limit of determination established at 0.1%. The absorption band at 1654 cm-1 was used to construct the calibration curve for quantification of caffeine where the regression was fitted with satisfactory linearity. An average of 0.55% of caffeine was detected in the seven coffee products with Arabica coffee demonstrating lower caffeine concentration. The study evidenced that caffeine content in coffee is determined by the coffee types. The caffeine content found in the local coffee products was relatively lower likely due to the solvent types, extraction procedure and analytical method used.
Fatty acid profile from crude extracts of local sea cucumber Stichopus chloronotus was determined using gas chromatography (GC) technique. The extracts were prepared separately in methanol, ethanol, phosphate buffer saline (PBS), and distilled water as part of our study to look at the affinity of these solvents in extracting the lipid from sea cucumber. The PBS and distilled water extractions indicate water-soluble components, while the organic fractions are extracted in methanol and ethanol as organic solvents. Furthermore, water extraction is the conventional method practiced in Malaysia. In our analysis the C14:0 (myristic), C16:0 (palmitic), C18:0 (stearic), C18:2 (linoleic), C20:0 (arachidic), and C20:5 (eicosapentaenoic, EPA) were significantly different (p < 0.01) in the four solvent extractions. However, the PBS extraction contained a much higher percentage of EPA (25.69%) compared to 18.89% in ethanol, 7.84% in distilled water, and only 5.83% in methanol, and variances were significantly different (p < 0.01 ). On the other hand, C22:6 (docosahexaenoic acid or DHA) is much higher in water extraction (57.55%), in comparison to the others where only 3.63% in PBS and 1.20% in methanol, and this difference is significant at p < 0.01. No DHA was detected in ethanol extractions. Subsequently, C18:1 (oleic acid) was only detected in PBS (21.98%) and water extraction (7.50%). It is interesting that palmitic acid, C16:() was higher in methanol (20.82%) and ethanol (2.18%), while 12.55% was detected in PBS and only 2.20% in water extraction: and again this was significantly different at p < 0.01. Although our results have shown that all four solvents were different in terms of their ability to extract fatty acids, the major component for tissue repair was well preserved. Probably this is one of the important precocious steps when working with a delicate sea cucumber, in both experimental and/or at the preparative stages. Freshness of the sea cucumber samples is important when undertaking this type of experiment. Finally, we believe that the local sea cucumber S. chloronotus contains all the fatty acids required to play a potential active role in tissue repair.
Consumption of mushroom has increased remarkably because of their desirable aroma, taste and high nutritional content. This study was undertaken to measure and compare the antioxidant activity, total phenolic content (TPC) and total flavonoid content (TFC) of Agaricus bisporous (white button mushroom) and Agaricus brasiliensis (Brazilian mushroom) in aqueous and 60% ethanol extract. Results showed that button mushroom (21.47 ± 0.48 mg GAE/g of dry weight) had significant higher TPC in aqueous whereas Brazilian mushroom (12.50 ± 0.22 mg GAE/g of dry weight) had significant higher TPC in 60% ethanol (p< 0.05). In terms of TFC, Brazilian mushroom had higher content than button mushroom in both types of solvents. For FRAP assay, Brazilian mushroom had significantly higher total antioxidant activity than the button mushroom in 60% ethanol (p < 0.05) but opposite trend with aqueous. For DPPH radical scavenging activity, Brazilian mushroom (60% ethanol) had the lowest EC50 value, followed by button mushroom (60% ethanol), Brazilian mushroom (aqueous) and button mushroom (aqueous). Pearson correlation test (p < 0.05) showed strong positive correlation between TPC and FRAP assay in both extracts (r = 0.969 for 60% ethanol extract; r = 0.973 for aqueous extract). For TFC, there was a strong positive, correlation with FRAP assay (r = 0.985) in aqueous extract. In conclusion, high antioxidant activity in ethanol extract of mushrooms due to presence of phenolic content can potentially be used as a source of natural antioxidants.