Carbon from jatropha seed hull (JC) was prepared to study the adsorption of cadmium ions (Cd(2+)) from aqueous solutions under various experimental conditions. Batch equilibrium methods have been used to study the influences of the initial metal ion concentration (0.5-50 ppm), dosage (0.2-1 g), contact time (0-300 min), pH (2-7), and temperature (26-60 °C) on adsorption behavior. It has been found that the amount of cadmium adsorbed increases with the initial metal ion concentration, temperature, pH, contact time, and amount of adsorbent. A kinetic study proved that the mechanism of Cd(2+) adsorption on JC followed a three steps process, confirmed by an intraparticle diffusion model: rapid adsorption of metal ions, a transition phase, and nearly flat plateau section. The experimental results also showed that the Cd(2+) adsorption process followed pseudo-second-order kinetics. The Langmuir and Freundlich adsorption isotherm models were used to describe the experimental data, with the former exhibiting a better correlation coefficient than the latter (R² = 0.999). The monolayer adsorption capacity of JC has been compared with the capacities of the other reported agriculturally-based adsorbents. It has been clearly demonstrated that this agricultural waste generated by the biofuel industry can be considered a potential low-cost adsorbent for the removal of Cd(2+) from industrial effluents.
This study investigated acclimation ability of native Chlorella sorokiniana (CS-N) and commercial Chlorella sorokiniana (CS-C) in palm oil mill effluent (POME), their metabolic profile and feasibility of effluent recycling for dilution purpose. Maximum specific growth rate, µmax and lag time, λ of the microalgae were evaluated. Result shows both strains produced comparable growth in POME, with µmax of 0.31 day-1 and 0.30 day-1 respectively, albeit longer λ by the CS-C. However, three cycles of acclimation was able to reduce λ from eight days to two days for CS-C. Metabolic profiling using principal component analysis (PCA) shows clear cluster of acclimatized strains to suggest better stress tolerance of CS-N. Finally, a remarkable µmax of 0.57 day-1 without lag phase was achieved using acclimatized CS-N in 40% POME concentration. Acclimation has successfully shortened the λ and dilution with final effluent was proved to be feasible for further improvement of the microalgae growth.
Greenhouse experiments were carried out to determine the phytotoxic effects on the plant Ludwigia octovalvis in order to assess its applicability for phytoremediation gasoline-contaminated soils. Using plants to degrade hydrocarbons is a challenging task. In this study, different spiked concentrations of hydrocarbons in soil (1, 2, and 3 g/kg) were tested. The results showed that the mean efficiency of total petroleum hydrocarbon (TPH) removal over a 72-day culture period was rather high. The maximum removal of 79.8 % occurred for the 2 g/kg concentration, while the removal rate by the corresponding unplanted controls was only (48.6 %). The impact of gasoline on plants included visual symptoms of stress, yellowing, growth reduction, and perturbations in the developmental parameters. The dry weight and wet weight of the plant slightly increased upon exposure to gasoline until day 42. Scanning electron microscopy (SEM) indicated change to the root and stem structure in plant tissue due to the direct attachment with gasoline contaminated compared to the control sample. The population of living microorganisms in the contaminated soil was found to be able to adapt to different gasoline concentrations. The results showed that L. octovalvis and rhizobacteria in gasoline-contaminated soil have the potential to degrade organic pollutants.
This paper elucidates the capability of isolated indigenous bacteria to remove aluminium from wastewater and soil. Two indigenous species of Brochothrix thermosphacta and Vibrio alginolyticus were isolated from an aluminium-contaminated site. These two species were used to treat aluminium-containing wastewater and contaminated soil using the bioaugmentation method. B. thermosphacta showed the highest aluminium removal of 57.87 ± 0.45% while V. alginolyticus can remove aluminium up to 59.72 ± 0.33% from wastewater. For aluminium-contaminated soil, B. thermosphacta and V. alginolyticus, showed a highest removal of only 4.58 ± 0.44% and 5.48 ± 0.58%, respectively. The bioaugmentation method is more suitable to be used to treat aluminium in wastewater compared to contaminated soil. The produced biomass separation after wastewater treatment was so much easier and applicable, compared to the produced biomass handling from contaminated soil treatment. A 48.55 ± 2.45% and 40.12 ± 4.55% of aluminium can be recovered from B. thermosphacta and V. alginolyticus biomass, respectively, with 100 mg/L initial aluminium concentration in wastewater.
The greenhouse phytotoxicity experiment was conducted to analyse and assess the capability of Scirpus mucronatus (L.) in tolerating and removing petrol in contaminated soil. This research was conducted for 72 days by using 5, 10 and 30 g/kg petrol as soil contaminants. Results showed that the system planted with S. mucronatus (L.) had high potential to treat the 10 g/kg petrol-contaminated soil and had an average Total Petroleum Hydrocarbon (TPH) removal of 82.1%. At 5 and 30 g/kg petrol, the planted system removed 74.9% and 75.8% TPH, respectively. The petrol (10 g/kg) affected the plant growth positively, which was indicated by the increase in dry and wet weights throughout the research period. The removal of the TPH in the system was performed because of the interaction of plants and rhizobacteria. SEM showed that a high concentration of petrol (30 g/kg) affected the plant tissue negatively, as indicated by the altered structures of the root and stem cells. EDX results also confirmed that petrol was absorbed by the plant, as shown by the increased carbon content in the plant's root and stem after the treatment.
Phytoremediation is an environmentally friendly technique in wastewater treatment because of its sustainability, cost-effectiveness, and simplicity. This study was conducted to examine the feasibility of use of Lepironia articulata, a potential phytoremediation plant that is native to Malaysia, in remediating coffee processing mill effluent (CPME). The aim was to determine effluent concentration or contaminant load that the plant can resist, while simultaneously results in the good removal of pollutants during phytoremediation. Four brushes of L. articulata were planted individually in a pail/reactor (mentioned as reactor afterward) containing 3 kg of sand and exposed to five different concentrations of CPME (0%, 30%, 50%, 75%, and 100%). The initial chemical oxygen demand (COD) values were 510, 3100, 4200, 7290, and 8470 mg/L, respectively, and ammoniacal nitrogen (AN) concentrations were 26, 128, 225, 376, and 509 mg/L, respectively. The height, appearance, and efficiency in removing COD and AN of each plant was observed throughout the 35-day exposure period. Results showed that plants exposed to 75% CPME demonstrated better growth than those exposed to other concentrations and exhibited the highest COD and AN removal rates (85.0% and 84.0%, respectively), providing evidence that L. articulata can be used as a phytoremediation agent of CPME with an initial COD concentration of 7290 mg/L and AN concentration of 376 mg/L. This study highlights its support to the Sustainable Development Goals adopted by the United Nations, particularly the reclamation of plant biomass used as a treatment agent and conversion into biodegradable straws. Moreover, this study adds an attractive additional point of transforming waste into resource with the proposed wastewater treatment technology.
In the present study, the potential of Salvinia molesta for biodecolorization of methyl orange (MO) dye from water was examined. Six glass vessels were filled with 4 L of water contaminated with MO with three concentrations (5, 15, and 25 mg/L), three with plants and another three without plant as contaminant control. The influence of operational parameters, including initial dye concentration, pH, temperature, and plant growth, on the efficacy of the biodecolorization process by S. molesta was determined. Temperature and pH was in the range of 25-26 °C and 6.3 to 7.3, respectively. Phytotransformation was monitored after 10 days through Fourier transform infrared (FTIR) spectroscopy, and a significant variation in the peak positions was demonstrated when compared to the control plant spectrum, indicating the adsorption of MO. The highest biodecolorization was 42% in a 5 mg/L MO dye concentration at pH 7.3 and at 27 °C. According to the FTIR results, a potential method for the biodecolourization of MO dye by S. molesta was proven. Salvinia molesta can be successfully used for upcoming eco-friendly phytoremediation purposes for dye removal.
In this study, the removal of arsenic (As) by plant, Ludwigia octovalvis, in a pilot reed bed was optimized. A Box-Behnken design was employed including a comparative analysis of both Response Surface Methodology (RSM) and an Artificial Neural Network (ANN) for the prediction of maximum arsenic removal. The predicted optimum condition using the desirability function of both models was 39 mg kg-1 for the arsenic concentration in soil, an elapsed time of 42 days (the sampling day) and an aeration rate of 0.22 L/min, with the predicted values of arsenic removal by RSM and ANN being 72.6% and 71.4%, respectively. The validation of the predicted optimum point showed an actual arsenic removal of 70.6%. This was achieved with the deviation between the validation value and the predicted values being within 3.49% (RSM) and 1.87% (ANN). The performance evaluation of the RSM and ANN models showed that ANN performs better than RSM with a higher R2 (0.97) close to 1.0 and very small Average Absolute Deviation (AAD) (0.02) and Root Mean Square Error (RMSE) (0.004) values close to zero. Both models were appropriate for the optimization of arsenic removal with ANN demonstrating significantly higher predictive and fitting ability than RSM.
Due to the increasing importance of diesel and petroleum for industrial development during the last century, petrochemical effluents have significantly contributed to the pollution of aquatic and soil environments. The contamination generated by petroleum hydrocarbons can endanger not only humans but also the environment. Phytoremediation or plant-assisted remediation can be considered one of the best technologies to manage petroleum product-contaminated water and soil. The main advantages of this method are that it is environmentally-friendly, potentially cost-effective and does not require specialised equipment. The scope of this review includes a description of hydrocarbon pollutants from petrochemical industries, their toxicity impacts and methods of treatment and degradation. The major emphasis is on phytodegradation (phytotransformation) and rhizodegradation since these mechanisms are the most favourable alternatives for soil and water reclamation of hydrocarbons using tropical plants. In addressing these issues, this review also covers challenges to retrieve the environment (soil and water) from petroleum contaminations through phytoremediation, and its opportunities to remove or reduce the negative environmental impacts of petroleum contaminations and restore damaged ecosystems with sustainable ways to keep healthy life for the future.
A reedbed system planted with Phragmites australis was implemented to treat chlorinated hydrocarbon-contaminated groundwater in an industrial plant area. Reedbed commissioning was conducted from July 2016 to November 2016 to treat contaminated groundwater via a pump-and-treat mechanism. Combination of horizontal and vertical reedbed systems was applied to treat 1,2-dichloroethane (1,2 DCA) under four parallel installations. The 2-acre horizontal and vertical reedbed systems were designed to treat approximately 305 m3/day of pumped groundwater. Initial concentration of 1,2 DCA was observed at 0.362 mg/L to 4320 mg/L, and the reedbed system successfully reduced the concentration up to 67.9%. The average outlet concentration was measured to be 2.08 mg/L, which was lower than the site-specific target level of 156 mg/L. Natural attenuation analysis was conducted using first-order decay kinetics, showing an average natural attenuation rate of 0.00372/year. Natural attenuation of 1,2 DCA was observed in shallow monitoring wells, which was indicated by the reduction trend of 1,2 DCA concentration, thereby confirming that the reedbed system worked well to remove 1.2 DCA from contaminated groundwater at the shallow profile.
Phytoremediation is an eco-friendly biotechnology with low costs. The removal of copper (Cu) from polluted water by the two floating plant species Azolla filiculoides and Lemna minor was observed and recorded. Plants were exposed to different Cu (II) concentration (0.25-1.00 mg/L) and sampling time (Days 0, 1, 2, 5 and 7). Both plants can remove Cu at 1.00 mg Cu/L water, with the highest removal rates of 100% for A. filiculoides and 74% for L. minor on the fifth day of exposure. At the end of the exposure period (Day 7), the growth of A. filiculoides exposed to 1.00 mg Cu/L was inhibited by Cu, but the structure of the inner cells of A. filiculoides was well organized as compared to the initial treatment period. Regarding L. minor, Cu at 1.00 mg/L negatively impacted both the growth and morphology (shrinking of its inner structure) of this plant. This is due to the higher accumulation of Cu in L. minor (2.86 mg/g) than in A. filiculoides (1.49 mg/g). Additionally, the rate of Cu removal per dry mass of plant fitted a pseudo-second order model for both plants, whereas the adsorption equilibrium data fitted the Freundlich isotherm, indicating that Cu adsorption occurs in multiple layers. Based on the results, both species can be applied in the phytoremediation of Cu-polluted water.
The application of plant-based coagulants in wastewater treatment has increasingly progressed in the coagulation-flocculation process toward green economy and cleaner production. Plant-based coagulants have a potential as essential substitutes for commercially used chemical coagulants because of their natural characteristics and biodegradability. Chemical coagulants leave residues in treated water and generated sludge, which cause harm to human health and the ecosystem. Thus, the exploration of plant-based coagulants in wastewater treatment could reduce and eliminate the potential damage of chemical coagulants and promote the alternative approach for sustainable environment. The general processing steps of the end-to-end plant-based coagulant production, which includes primary, secondary, and tertiary stages, are discussed. However, this review focuses more on the extraction process using different solutions and compares the performance of different coagulants in removal activities after effluent treatment. Discussion on the arising challenges is elaborated, and approaches for plant-based coagulant research in the near future are suggested.
The contamination of aquaculture products and effluents by contaminants of emerging concern (CECs) from the direct chemical use in aquaculture activities or surrounding industries is currently an issue of increasing concern as these CECs exert acute and chronic effects on living organisms. CECs have been detected in aquaculture water, sediment, and culture species, and antibiotics, antifoulants, and disinfectants are the commonly detected groups. Through accumulation, CECs can reside in the tissue of aquaculture products and eventually consumed by humans. Currently, effluents containing CECs are discharged to the surrounding environment while producing sediments that eventually contaminate rivers as receiving bodies. The rearing (grow-out) stages of aquaculture activities are issues regarding CECs-contamination in aquaculture covering water, sediment, and aquaculture products. Proper regulations should be imposed on all aquaculturists to control chemical usage and ensure compliance to guidelines for appropriate effluent treatment. Several techniques for treating aquaculture effluents contaminated by CECs have been explored, including adsorption, wetland construction, photocatalysis, filtration, sludge activation, and sedimentation. The challenges imposed by CECs on aquaculture activities are discussed for the purpose of obtaining insights into current issues and providing future approaches for resolving associated problems. Stakeholders, such as researchers focusing on environment and aquaculture, are expected to benefit from the presented results in this article. In addition, the results may be useful in establishing aquaculture-related CECs regulations, assessing toxicity to living biota, and preventing pollution.
Batik is well known as one of the unique identifiers of the Southeast Asian region. Several countries that still preserve the batik heritage are Malaysia, Indonesia, China and India. The Batik industry holds a significant place in Malaysia's craft-based industry. In Malaysia, batik motifs and patterns are mostly hand-drawn and painted directly on fabric, therefore, each one is unique. The players in the Batik industry are mostly small businesses and cottage industries, particularly in the states of Kelantan, Terengganu, Pahang, Sabah and Sarawak. However, their market growth and contribution are not synchronized with the treatment system. The wastewater generated by this industry rarely meets standard effluent requirements and regulations, thus worrying the authorities. Batik wastewater is categorized as one of the highly polluted wastewaters. The toxicity of pollutants from batik may reduce environmental quality and pose a risk to human health. Batik wastewater needs extensive treatment, since no complete and appropriate treatment has been applied for so many years in specific batik industries. This paper reviews the batik industry in Malaysia, its wastewater generation and the available current treatment practices. It discusses integrated treatments of coagulation-flocculation and phytoremediation technology as a batik wastewater treatment process with potential utility in the batik industry. This review may become part of the guidance for the entire batik industry, especially in Malaysia.
Dye is one of the pollutants found in water bodies because of the increased growth of the textile industry. In this study, Scirpus grossus was planted inside a constructed wetland to treat mixed dye (methylene blue and methyl orange)-containing wastewater under batch and continuous modes. The plants were exposed to various concentrations (0, 50, 75, and 100 mg/L) of mixed dye for 72 days (with hydraulic retention time of 7 days for the continuous system). Biological oxygen demand, chemical oxygen demand, total organic carbon, pH, temperature, ionic content, and plant growth parameters were measured. Results showed that S. grossus can withstand all the tested dye concentrations until the end of the treatment period. Color removal efficiencies of 86, 84, and 75% were obtained in batch mode, whereas 90%, 85%, and 79% were obtained in continuous mode for 50, 75, and 100 mg/L dye concentrations, respectively. Fourier-transform infrared analysis confirmed the transformation of dye compounds after treatment and scanning electron microscopy coupled with energy-dispersive X-ray spectroscopy analysis showed that most of the intermediate compounds were not absorbed into plants but adsorbed onto the surface of the root structure.
Heavy metal wastes, particularly hexavalent chromium [Cr(VI)], are generated from anthropogenic activities, and their increasing abundance has been a research concern due to their toxicity, genotoxicity, carcinogenicity and mutagenicity. Exposure to these dangerous pollutants could lead to chronic infections and even mortality in humans and animals. Bioremediation using microorganisms, particularly bacteria, has gained considerable interest because it can remove contaminants naturally and is safe to the surrounding environment. Bacteria, such as Pseudomonas putida and Bacillus subtilis, can reduce the toxic Cr(VI) to the less toxic trivalent chromium Cr(III) through mechanisms including biotransformation, biosorption and bioaccumulation. These mechanisms are mostly linked to chromium reductase and nitroreductase enzymes, which are involved in the Cr(VI) reduction pathway. However, relevant data on the nitroreductase route remain insufficient. Thus, this work proposes an alternative metabolic pathway of nitroreductase, wherein nitrate activates the reaction and indirectly reduces toxic chromium. This nitroreductase pathway occurs concurrently with the chromium reduction pathway.
Chromium (Cr) is used as a mixture to improve strength and corrosion resistance. Milling and welding processes can expose workers to Cr through dermal exposure and inhalation. Cr exposure can be determined by urine testing. The purpose of this study was to analyze the concentration of Cr in urine (UCr) of workers. This study was carried out using a cross-sectional method. Sampling was conducted in the village of Mekarmaju, Bandung, Indonesia. The number of respondents included 30 blacksmiths, and the control group comprised 10 people who were not blacksmiths. Cr6+ exposure was measured using a personal sampling pump placed on the collar of the worker's shirt as a breathing zone and then analyzed using a UV-visible spectrophotometer. UCr was measured with a graphite furnace atomic absorption spectrophotometer. The measured Cr6+ concentration in the exposed working area ranged from 0.03 to 0.63 mg/m3, whereas that in non-exposed area ranged from 0.02 to 0.04 mg/m3. Results showed that 16 out of 30 blacksmiths had a UCr concentration above the biological exposure index (BEI) value, 21 had a higher value than the threshold limit value (TLV), and 22 had hazard index (HI) values > 1, which indicated that Cr has a hazardous potential in the body. The analysis of the exposed and control groups showed a significant difference with a p value of 0.000 for TLV, chronic daily intake, and UCr. These results clearly showed that Cr6+ exposure may harm the health of these workers in the future. The results obtained in this study can be used to promote workers' awareness on the potential health risk caused by Cr6+ exposure in the working environment.
The performance of local plants was tested using synthetic turbid water resembling real wastewater by measuring their ability to remove turbidity. The selected plants were A. indica, S. palustris, D. linearis, S. polyanthum, M. esculenta, P. sarmentosum, and M. malabathricum which can easily be found locally. The experiment was run based on coagulant dosages varied from 0 to 10 g/L for each plant with a rapid mixing speed at 180 rpm for 3 min, slow mixing speed at 10 rpm for 20 min, and settling time for 30 min. The results demonstrated that each plant has been capable of reducing turbidity by different amounts, with an increase in the coagulant dosage. The optimum coagulant dosages achieved for A. indica, S. palustris, S. polyanthum, and D. linearis were 10 g/L with turbidity removal at 26.9%, 24.9%, 24.9%, and 17.5%, respectively. P. sarmentosum and M. esculenta attained optimum coagulant dosages at 5 g/L with turbidity removal at 24.2% and 22.2%, and lastly M. malabathricum at 0.1 g/L (12.2%). P. sarmentosum was suggested to the best natural coagulant which achieved the highest removal of turbidity with a low dosage used.
This study aims to determine the distribution of organochlorine pesticide pollution in water, sediments, mollusks, and fish at Saguling Dam as baseline data of organochlorine pollution. Samples were obtained from 12 locations, with 9 and 3 sampling points inside and outside the dam, respectively. Measurement of organochlorine residues was carried out using methods of extraction, purification, evaporation, and gas chromatography. Results showed the presence of several types of organochlorine compounds, namely, lindane, aldrin, dieldrin, heptachlor, dichlorodiphenyltrichloroethane (DDT), and endosulfan. Aldrin was dominant in water (2-37 μg/L) and sediments (2-1438 μg/L), while DDT and heptachlor were dominant organochlorine compounds in mollusks (13-2758 µg/L) and fish (11-104 μg/L), respectively. Sediments demonstrated higher organochlorine concentrations than water, mollusk, and fish. The distribution of organochlorine was affected by land use around the Citarum watershed and pollutant input from tributaries.
The batik industry has been one of the main family businesses in most of the east-coast region of the Malaysian peninsula for many years. However, appropriate water treatment is still a major challenge for this industry. Stringent laws introduced by the Malaysian authorities and the intention to protect the environment are factors that drive researchers to search for suitable, appropriate, affordable and efficient treatment of batik wastewater. Treatment research on batik wastewater is still lacking and coagulation-flocculation treatment using alum was introduced and chosen as a stepping stone toward the selection of green coagulants. This study aimed to determine the best conditions for alum flocculation-coagulation using a standard jar test method. Four main factors were investigated: alum dosage (0.1-3.5 g/L), pH (4-11), settling time (0.5-24 h) and rapid mixing rate (100-300 rpm). Results obtained were further analysed statistically using SPSS software prior to determining the significant effect of variable changes. From this study, the best conditions for batik wastewater treatment using the flocculation-coagulation process were found to be at alum dosage of 1.5 g/L, pH 8, 4 h settling time and a rapid mixing rate of 100 rpm. Chemical oxygen demand (COD), turbidity, colour and total suspended solids (TSS) were removed by 70.7, 92.2, 88.4 and 100%, respectively, under these conditions. This study showed that batik wastewater can be treated by the coagulation-flocculation process using chemical means of alum. This indicates the need for forthcoming developments in natural-based-coagulant-flocculants toward the sustainability of the batik industry.