In this paper a study on the wideband double-pass Raman fibre amplifier with mirror as the pump reflector is reported. The pump lights at 1435 nm and 1455 nm were launched in a co-directional manner with respect to the input signal. The double-pass direction of the signal was achieved through a fibre loop mirror constructed using an optical circulator. It was shown that multiple signal amplification was achieved without any disturbance of stimulated Brillouin scattering.
The effects of backward, forward, and bidirectional Raman pumping schemes on stimulated Brillouin scattering (SBS) is investigated in this study. By using a linear cavity, we utilize residual Brillouin pump (BP) and Raman pump (RP) power after each transmission through a 25 km single-mode fiber (SMF) used as a gain medium. The SBS threshold power is reduced in the forward, backward, and bidirectional Raman pumping schemes by 2.5, 1.75, and 2.75 dB, respectively when the 1480 nm RP power is fixed at 150 mW and the BP wavelength is 1580 nm. Surprisingly, it is revealed that the SBS threshold reduction depends strongly and solely on Raman gain and it is independent of the Raman pumping schemes. In addition, the effect of Raman amplification on SBS is more effective at the SBS threshold, especially in the bidirectional and forward schemes.
A novel fiber tapering shape, which is based on compound parabolic geometry, is proposed to increase the acceptance angle of a compound parabolic concentrator. The proposed design is described by use of ray optics on a step-index multimode fiber.
A four-stage erbium-doped fibre amplifier with the gain bandwidth of 35 nm is demonstrated. The amplifier was designed to include a dispersion compensating module to compensate the accumulated dispersion by signals. The amplifier design permited some dynamic features such as the amplifier’s gain could be adjusted from 15 dB to 30 dB by varying the input signal power from –26 dBm to 8 dBm. The maximum output power of 23 dBm was obtained with a maximum allowable gain flatness of 1.5 dB.
This paper reviewed the aspect of fatigue approaches and analysis in a fibre reinforced composite materials which have been done by researchers worldwide. The aim of this review is to provide a better picture on analytical approaches that are presently available for predicting fatigue life in composite materials. This review also proposes a new interpretation of available theories and identifies area in fatigue of natural fibre reinforced composite materials. Thus, it was concluded there are still very limited studies on fatigue analysis of natural fibre reinforced composite materials, especially using non-destructive technique (NDT) methods and a new mathematical modelling on fatigue should be formulated.
This paper presents an overview topic of layered and laminated fibre composites. The review presents an investigation on the effect of varying the properties of fibre and the matrix of layered and laminated composites and identifies the fundamental parameters determining ballistic impact protection. The advantages of layered and laminated reinforced composites with different thicknesses for further enhancing ballistic penetration resistance of the laminated fibre composite have been reviewed. Lamination of multiple layers of composite material can give better ballistic performance.
A fiber based bend sensor using a uniquely designed Bend-Sensitive Erbium Doped Fiber (BSEDF) is proposed and demonstrated. The BSEDF has two core regions, namely an undoped outer region with a diameter of about 9.38 μm encompassing a doped, inner core region with a diameter of 4.00 μm. The doped core region has about 400 ppm of an Er2O3 dopant. Pumping the BSEDF with a conventional 980 nm laser diode gives an Amplified Spontaneous Emission (ASE) spectrum spanning from 1,510 nm to over 1,560 nm at the output power level of about -58 dBm. The ASE spectrum has a peak power of -52 dBm at a central wavelength of 1,533 nm when not spooled. Spooling the BSEDF with diameters of 10 cm to 2 cm yields decreasing peak powers from -57.0 dBm to -61.8 dBm, while the central wavelength remains unchanged. The output is highly stable over time, with a low temperature sensitivity of around ~0.005 dBm/°C, thus allowing for the development of a highly stable sensor system based in the change of the peak power alone.
A single-wavelength Brillouin fiber laser (BFL) is demonstrated at the extended L-band region using bismuth-based erbium-doped fiber (Bi-EDF) for the first time to the best of our knowledge. A 2.15-m-long Bi-EDF is used to provide both nonlinear and linear gains to generate a stimulated Brillouin scattering (SBS) and to amplify the generated SBS, respectively. The BFL operates at 1613.93 nm, which is upshifted by 0.09 nm from the Brillouin pump with a peak power of 2 dBm and a side-mode suppression ratio of more than 22 dB. The generated BFL has a narrow linewidth and many potential applications, such as in optical communication and sensors.
In this paper, we present the development and testing of an optical-based sensor for monitoring the corrosion of reinforcement rebar. The testing was carried out using an 80% etched-cladding Fibre Bragg grating sensor to monitor the production of corrosion waste in a localized region of the rebar. Progression of corrosion can be sensed by observing the reflected wavelength shift of the FBG sensor. With the presence of corrosion, the etched-FBG reflected spectrum was shifted by 1.0 nm. In addition, with an increase in fringe pattern and continuously, step-like drop in power of the Bragg reflected spectrum was also displayed.
Fiber composites are known to have poor through-thickness mechanical properties due to the absence of a Z-direction binder. This issue is more critical with the use of natural fibers due to their low strength compared to synthetic fibers. Stitching is a through-thickness toughening method that is used to introduce fibers in the Z-direction, which will result in better through-thickness mechanical properties. This research was carried out to determine the mechanical properties of unstitched and silk fiber-stitched woven kenaf-reinforced epoxy composites. The woven kenaf mat was stitched with silk fiber using a commercial sewing machine. The specimens were fabricated using a hand lay-up method. Three specimens were fabricated, one unstitched and two silk-stitched with deferent stitching orientations. The results show that the stitched specimens have comparable in-plane mechanical properties to the unstitched specimens. For the tensile mechanical test, stitched specimens show similar and 17.1% higher tensile strength compared to the unstitched specimens. The flexural mechanical test results show around a 9% decrease in the flexural strength for the stitched specimens. On the other hand, the Izod impact mechanical test results show a significant improvement of 33% for the stitched specimens, which means that stitching has successfully improved the out-of-plane mechanical properties. The outcome of this research indicates that the stitched specimens have better mechanical performance compared to the unstitched specimens and that the decrease in the flexural strength is insignificant in contrast with the remarkable enhancement in the impact strength.
The concrete-filled double skin steel tube (CFDST) is a more viable option compared to a concrete-filled steel tube (CFST) due to consisting a hollow section, while degradation is enhanced simply by using carbon fiber-reinforced polymer (CFRP). Hence, the stabilization of a concrete's ductile strength needs high- performance fiber-reinforced cementitious conmposite. This study investigates the behavior of high-performance fiber-reinforced cementitious composite-filled double-skin steel tube (HPCFDST) beams strengthened longitudinally with various layers, lengths, and configurtion of CFRP sheets. The findings showed that, with increased CFRP layers, the moment capacity and flexural stiffness values of the retrofitted HPCFDST beams have significantly improved. For an instant, the moment capacity of HPCFDST beams improved by approximately 28.5% and 32.6% when they were wrapped partially along 100% with two and three layers, respectively, compared to the control beam. Moreover, the moment capacity of the HPCFDST beam using two partial layers of CFRP along 75% of its sufficient length was closed to the findings of the beam with two full CFRP layers. For energy absorption, the results showed a vast disparity. Only the two layers with a 100% full length and partial wrapping showed increasing performance over the control. Furthermore, the typical failure mode of HPCFDST beams was observed to be local buckling at the top surface near the point of loading and CFRP rapture at the bottom of effect length.
Natural fiber reinforced composites are recognized as better materials for structural components due to their inherent properties. However, milling these materials presents a number of problems, such as surface delamination, which appeared during the machining process, associated with the characteristics of the material and the cutting parameters. Therefore, in this study, machining parameters and the influence of the banana fibers under delamination were investigated. Result showed that machining parameters has a significance effect on the delamination of banana fiber reinforced polyester composites.
Currently, research in composite materials is being directed at using natural fibers instead of synthetics fibers. The use of natural fibers, derived from annually renewable resources, as reinforcing fibers in matrix provides positives environmental benefits with respect to ultimate disposability and raw material utilization. Natural fiber offers an alternative to the technical reinforcing fibers because of their low density, good mechanical performance, ultimate availability and disposability. Modifying the fiber surface by using chemical treatment can enhance bond strength between fiber and matrix. Chemical treatment also an effective way to clean the fiber surface, chemically modify the surface and increase the surface roughness. Surface analyses on fiber for before and after treatment were investigated using scanning electron microscopy (SEM).
This paper proposes a signal-to-noise-ratio (SNR) improvement by using an external phase modulator that allowed flexible control of the spectrum amplitude by varying the modulation index for linewidth measurements. Compared with the conventional self-heterodyne detection technique, the results obtained in this study showed an SNR improvement as high as 10 dB. This 10 dB improvement in SNR could help to reduce the usage of a particular length of a single mode fibre (normally about 50 Km) when measuring a linewidth in the region of 10 kHz.
The properties of fibre-reinforced composites are dependent not only on the strength of the reinforcementfibre but also on the distribution of fibre strength and the composition of the chemicals or additivesaddition within the composites. In this study, the tensile properties of abaca fibre reinforced high impactpolystyrene (HIPS) composites, which had been produced with the parameters of fibre loading (30,40,50wt.%), coupling agent maleic anhydride (MAH) (1,2,3 wt%) and impact modifier (4,5,6 wt.%) weremeasured. The optimum amount of MAH is 3% and the impact modifier is 6% and these give the besttensile properties. Meanwhile, Differential Scanning Calorimetry (DSC) was used to study the thermalbehaviour within the optimum conditions of the composites. In this research, glass transitions temperature(Tg) of neat HIPS occurred below the Tg of the optimum condition of composites as the temperature ofan amorphous state. The endothermic peak of the composites was in the range of 430-4350C, includingneat HIPS. It was observed that enthalpy of the abaca fibre reinforced HIPS composites yielded belowthe neat HIPS of 748.79 J/g.
The purpose of this research is to enhance the gain signal amplification by using dual
pump double pass configuration in comparative with single pump double pass that are
commonly used as conventional optical amplifier configuration in optical
communication system nowadays. Two input signals power have been implemented
which are -30 and 0 decibel (dB). The input signal defined as low and high input signals
power by using a pump power of 1480 nm. The amplification of EDFA in this study have
been taken place in conventional band (C) band and long wavelength band (L) band of
EDFA within the range of 1515 to 1615 nm. Therefore, to understand the performance
of the gain amplification, the OptiSystem software simulator version 13 has been used
for simulation and the values of fiber length and pump power has been varied for both
configurations. It has been found that the, dual pump double pass configuration has
shown better gain performance at lower input signal power compared to the single
pump double pass configuration.
This paper reports the effect of microbending losses in single mode optical fiber
for pressure sensing system application. Several types of periodical corrugated
plates were fabricated, namely cylindrical-structured surface (Plate A) and
rectangular-structured surface (Plate B) with thicknesses of corrugated parts
were varied at 0.1 cm, 0.2 cm and 0.3 cm. Laser sources with excitation
wavelengths of 1= 1310 nm and 2= 1550 nm were launched at the first end
of the fiber. The values of losses were recorded by using an optical power
meter. It was clearly seen that the microbending losses were polynomially
increased with the increment of applied pressure and the thicknesses of
corrugated parts of Plate A and Plate B. The maximum microbending losses of
1.5185 dBm/kPa was resulted as SMF was coupled with corrugated plates B
with thicknesses of 0.3cm by using excitation wavelength of 1550nm. These
values reduced to 0.7628 dBm/kPa and 0.4014 dBm/kPa as the thicknesses
were decreased to 0.2cm and 0.1cm respectively. In comparison with a plain
plate which acted as a reference indicator, the maximum percentage of
microbending losses was obtained as 74.29 % for Plate A and 95.02 % for Plate
B. In conclusions, we successfully proved the ability of SMF as a pressure sensor
by manipulating the microbending losses experienced by the fiber. The
employment of 1550nm of laser wavelength results better sensitivity sensor
where the system able to detect large losses as the pressure applied on the
corrugated surfaces.
This paper presents an evaluation of the alternative use of natural cellulose coir fibres for
soil reinforcement. Soil reinforcement is defined as a technique to improve the engineering properties
of soil. Inserting natural fibres into the soil has been proposed as a reinforcement method. Randomly
distributed coir fibre reinforced soils have recently attracted increasing attention in geotechnical
engineering due to their strength. Furthermore, there is a need to develop an innovative and
sustainable pre-treatment method to improve the effectiveness and performance of coir fibre as soil
reinforcement. The primary purpose of this paper is, therefore, to review the characteristics, benefits,
applications and weaknesses of coir fibre as soil reinforcement.
The culms of bamboo Bambusa rigida ranging from 1, 3 and 5 year old were obtained and investigated for anatomical characteristics in different ages, heights and zones in radial direction of culm wall thickness. The vascular bundles were denser and smaller at the top portion and outer zone of all age groups. No significant differences in vascular bundle frequency and size were found among the tree age groups. Metaxylem vessels did not vary significantly among ages. Fibre and parenchyma were longer in the middle portion of the height and middle zone in radial direction of culms wall. No significant differences in fibre and parenchyma length were observed in all age groups. The wall thicknesses of fibre and parenchyma were thicker in the top portion and outer zone. Furthermore, the wall thicknesses of fibre and parenchyma increased significantly from 1 to 3 year, showing that there is a maturing progress from 1 to 3 year.
The mechanical strength of magnetic lumen loaded handsheets was reported to be lower than the unloaded handsheets. This effect is due to the deposition of filler inside the fiber lumen and some on the fibre surface which interfere with the fibre to fibre bonding. Hence, in order to improve the handsheets strength, cationic starch is used as a dry strength additive. In this study, mixed tropical hardwood pulps were used throughout the experiment. The magnetite particles were deposited in the fibre lumen via the lumen loading technique. The addition of cationic starch was found to increase the handsheet strength. However, it disturbed and influenced the location and distribution of the magnetic fillers. Some of the magnetite particles were observed to be displaced from the fiber lumen and pit apertures. The charges of the filler particles and cationic starch played an important role in producing charge repulsion and pulling effect which lead to filler dislocation.