Raw goat milk is recognized as one kind of nutritious food owed to its originality and
medicinal values. This study aimed to evaluate the physico-chemical and microbiological
qualities of locally produced raw goat milk prior any processing steps during storage. Milk
samples passed organoleptic test and C.O.B. test were mostly (88.89 %) failed in alcohol test.
AOAC Official method of oven drying method, Kjeldahl method and Soxhlet method were
performed in physico-chemical analysis where results obtained were partially in lined with
reported literature due to subjective factors of breeds, geographical areas and feeds. The locally
produced raw goat milk’s compositions are high in water content and low in fat percentage.
Initial total plate count, coliform count and proteolytic count tested were 3.44 log cfu/ml, 1.87
log cfu/ml and 1.97 log cfu/ml, respectively. Storage time showed significant effect on the
bacterial counts (p>0.05) of milk samples. Shelf-life of milk samples were kept up to 12 hours
under ambient temperature (3.95 log cfu/ml) had not exceeded the standard limit. The shelflife
of the milk samples were extended up to 16 days storage under refrigerated temperature
of 4°C. The microbiological quality of the milk samples showed a significant bacteriological
growth upon prolonged storage and high initial coliform count indicates possible poor hygienic
practices at farm level.
The microstructural evolution of Sn-40Pb/Cu joints has been investigated under 125 o C thermal exposure conditions using single shear lap joints. A scanning electron microscope (SEM) was used to observe the morphology of the phases and energy dispersive x-ray (EDX) was used to estimate the elemental compositions of the phases. A double layer of Cu6Sn5 and Cu3Sn were observed. The Cu6Sn5 developed with a scalloped morphology, while the Cu3Sn always grew as a somewhat undulated planar layer in phase with the Cu6Sn5. The Cu6Sn5 layer began to transform from scallop shape to planar type after aging for 375 hours due to reduction in the interfacial energy. The intermetallic layers showed a linear dependence on the square root of aging time. The growth rate constant of the intermetallic compounds are estimated as 15.2 x 10 - 14 and 0.152 x 10 -14 cm 2 /s for Cu6Sn5 and Cu3Sn intermetallic, respectively.
The objective of this research is recovery of squalene from palm fatty acid distillate (PFAD) using supercritical fluid extraction (SFE). The extraction process was performed by using the SFE and recovered squalene was analyzed from total lipid extracts using HPLC. A central composite design was used to study the effect of SFE variables namely pressure (X₁) from 200 to 400 bar and temperature (X₂) from 40 to 60⁰C on the total lipid extracts (Y₁) and squalene concentration (Y₂) and optimize the SFE conditions. The nonlinear regression equations were significantly (p < 0.05) fitted for both responses with high R₂ (> 0.965), which had no indication of lack of fit. The results indicated that a combined pressure (200 bar) and temperature (50⁰C) was predicted to provide the optimum region in terms of total lipid extracts (13.84 ± 0.52%) and squalene concentration (418.31 ± 18.40 ppm) studied.
The presence of 226 Ra in water is a great concern in human life since it can cause health risk to a certain extent. In the state of Kelantan, being known of its granitic area, there is a lack measurement of 226 Ra content in river water, since water is the major source of water supply. According to the INTERIM National Water Quality Standards for Malaysia (INWQS), 226 Ra activity concentration in water cannot exceed 0.1 Bq/L. For this reasons, this research was planned to carry out a systematic measurement of water along Sungai Kelantan. Liquid Scintillation Counting was used for measurement of 226 Ra in water samples from Sungai Kelantan mainly in district of Kuala Krai. In this paper, the results obtained is about 26 water samples, filtered and unfiltered, collected along Sungai Lebir, Sungai Sok and Bukit Sabah. Thus, the assessment activity concentration of 226 Ra in river water was obtained as well as annual effective dose for consumption of drinking water.
This paper presents investigations into the development of control schemes for end-point vibration
suppression and input tracking of a flexible manipulator. A constrained planar single-link flexible manipulator is considered and the dynamic model of the system is derived using the assumed mode method. To study the effectiveness of the controllers, a Linear Quadratic Regulator (LQR) was initially developed for control of rigid body motion. This is then extended to incorporate a noncollocated PID controller and a feedforward controller based on input shaping techniques to control vibration (flexible motion) of the system. For feedforward controller, positive and modified specified negative amplitude (SNA) input shapers are proposed and designed based on the properties of the system. Results from the simulation of the manipulator responses with the controllers are presented in time and frequency domains. The performances of the control schemes are assessed in terms of level of vibration reduction, input tracking capability and time response specifications. Finally, a comparative assessment of the control techniques is presented and discussed.
Natural radionuclides such as 210 Po and 210 Pb were analyzed in soft part of cockle (Anadara granosa) obtained from Kuala Selangor in the west coast Peninsular of Malaysia. The activity levels of both nuclides fluctuated within the size of cockles from 41.3 ± 2.5 Bq/kg to 114 ± 7 Bq/kg and 12.9 ± 1.7 Bq/kg to 96.8 ± 5.3 Bq/kg in dry weight (dwt) for 210 Po and 210 Pb, respectively. The level activity in wet weight (wwt) also varied from 8.60 ± 0.52 Bq/kg to 25.70 ± 1.63 Bq/kg and 2.47 ± 0.40 Bq/kg to 19.27 ± 1.05 Bq/kg for 210 Po and 210 Pb, respectively, probably related to the different of metabolic rate and growth of cockles. Activity ratio of 210 Po/ 210 Pb in dry weight also fluctuated from 0.93 to 6.41 with not related to the decay of 210 Pb.
Nuclear grade (high-purity) graphite for fuel element and moderator material in Advanced Gas
Cooling Reactors (AGR) displays large scatter in strength and a non-linear stress-strain response from the damage accumulation. These responses can be characterized as quasi-brittle behaviour. Current assessments of fracture in core graphite components are based on the linear elastic approximation and thus represent a major assumption. The quasi-brittle behaviour gives challenge to assess the real nuclear graphite component. The selected test method would help to bridge the gap between microscale to macro-scale in real reactor component. The small scale tests presented here can contribute some statistical data to manifests the failure in real component. The evaluation and choice of different solution design of biaxial test will be discussed in this paper. The ball on-three ball test method was used for assessment test follows by numerous of analytical method. The results shown that biaxial strength of the EY9 grade graphite depends on the method used for evaluation. Some of the analytical methods use to calculate biaxial strength were found not to be valid and therefore should not be used to assess the mechanical properties of nuclear graphite.
Bacillus cereus is a soil inhabitant gram positive bacterium, and is known to cause severe food poisoning. The objective of this study was to isolate and identify the presence of Bacillus cereus s.l. from selected ready to eat cereals purchased randomly from local supermarkets in Kuching and Kota Samarahan, Sarawak. The result showed that four of the 30 food samples were detected to be contaminated by B. cereus s.l. . Our findings suggested that it is important for the public to be aware of the safety of RTE cereals consumption, as it is possible that B. cereus s.l. may be present in high count number and pose hazardous health effects to the consumers.
Balance and motor skills are essential prerequisites for physical development of a child. The aims of this study were to measure anthropometrics, postural balance and motor skills; and examine their correlation among healthy preschool children. Forty nine healthy preschool children aged between 3 to 4 years old participated from PERMATA preschool organization. Pediatric Balance Scale and Peabody Development Motor Scale-2nd Edition (PDMS-2) were administered to measure balance skills for both fine and gross motor skills respectively. Mann-Whitney U test demonstrated that there was no significant difference in balance (p=0.72) and motor skill (p=0.33) between boys and girls. Spearman correlation coefficient demonstrated that there was significant correlation between balance skills with height (r=0.45, p=0.001) and body mass index(r=0.47, p=0.001). No significant correlation was found between balance skills and motor skills (r=0.11, p=0.44). The present study suggests that balance skills in healthy preschool children aged 3-4 years old are correlated with their physical growth such as height and weight but not motor skills.
A series of polycrystalline samples (La1-xSmx)0.67Sr0.33MnO3 (X=0.00, 0.05 and 0.10) were prepared using the conventional solid-state reaction method. The XRD analysis indicated that all the samples were fully crystalline and in a single phase with a rhombohedral structure after a sintering at 1200ºC for 24 hours in air. Meanwhile, the Atomic Force Microscopy measurements showed that a small amount of Sm doping in La sites affected the grain growth and this might affect the grain boundary layer, thus resulting in the reduction of the Curie temperature, TC. Extrinsic magnetoresistance (MR) was observed for all the samples with a large negative MR at low field (0-0.1 or 0.2T) region, followed by a slower varying MR at high field (0.1 or 0.2-1T). The highest low-field MR value of -4.6% (at 0.1T) and -6.1% (at 0.2T) were observed for sample X=0.10 and X=0.05, respectively. Hence, these indicated that the extrinsic MR was grain size dependent and was therefore enhanced with a small amount of Sm substitution in La sites.
The emergence of research about the biological effects of electromagnetic field (EMF) have growing concern among
researchers. The aim of this study was to investigate the effects on the brain of rats periodically exposed to 0.1 mT EMF.
Total 24 adult male Sprague Dawley rats were subdivided randomly to 4 groups: 2 control groups (C1 6 hours: 6 h/
day for 5 days; C2 20 hours: 20 h/day for 5 days) and 2 treatment groups which exposed to 0.1 mT EMF (T1 6 hours:
6 h/day for 5 days; T2 20 hours: 20 h/day for 5 days). A significant decrease in the pyramidal cell number was higher
as the exposure duration to EMF was extended (T1, p
Compartmented Fluidized Bed Gasifier (CFBG), consisting of two compartments - the combustorand gasifier, uses air blown instead of pure oxygen for syngas production in bubbling fluidization mode, eliminating the need of air separation unit, and reducing the capital cost, thus distinguishes it from other traditional ones. Fluidization quality is a determining factor in the CFBG to guarantee its well-lifted behaviour. Previous study, without solid circulation at ambient conditions, brought to the fore the necessity of considering the effect of the minimum allowable effective diameter. The study was then performed in the CFBG cold physical model of 0.66m overall diameter (effective diameter for combustor and gasifier is 0.413m and 0.257m) to investigate the fluidization quality and compare it with the results obtained from the previous cold model of about 1.36 times smaller, but with the same compartmented ratio of 65:35. Different inert particles (river sand, quartz sand and alumina) were used, over a range of aspect ratios, for the aforementioned objective. The results showed that the fluidization quality in the gasifier has not been achieved and the degradation of fluidization quality in the combustor is still observed, notwithstanding the fact that the condition of the minimum allowable effective diameter has been met. The reduction of distributor free area, to increase the distributor pressure drop, showed a marginal effect on the quality. The effect of the minimum allowable effective diameter on fluidization quality in CFBG as well as the interplay of geometric and operational parameters require further studies be carried out. The fluidization quality of the binary mixture is also currently under investigation.
Breast-feeding offers many benefits to the baby and the mother. For instance, breast milk provides the right balance of nutrients to help an infant grow into a strong and healthy toddler. Even though breastfeeding is a natural process, it is not always easy. In certain situations, some mothers are unable to breastfeed their babies or the babies are unable to adapt to breastfeeding. This will lead to the use of bottle-feeding. The effect of breast-feeding and bottle-feeding on physical growth has been well established but less has been concentrated on the craniofacial growth and dental development. This review reveals the effects of breast-feeding and bottle-feeding on craniofacial growth and dentoalveolar development based on the available literature.
Lead-free solder paste printing processes account for the majority of assembly defects in the electronic manufacturing industry. In the stencil printing process, the solder paste must be able to withstand low and high shear rates which result in continuous structural breakdown and build-up. This study investigated the effect of the addition of nickel and platinum powders to the thixotropic behaviour of lead-free Sn/Ag/Cu solder pastes using the structural kinetic model. A hysteresis loop test and constant shear test were utilized to investigate the thixotropic behaviour of the pastes using parallel plate rheometry at 25ºC. In this study, the shear rates were increased from 0.01 s–1 to 10 s–1 and the second curve was a result of decreasing the shear rate from 10 s–1 to 0.01 s–1. For the constant shear test, the samples were subjected to five different shear rates of 0.01s–1, 0.1s–1, 1s–1, 10s–1 and 100s–1. The constant shear rate test was designed to study the structural breakdown and build-up of the paste materials. From this investigation, the hysteresis loop test was shown to be an effective test method to differentiate the extent of structural recovery in the solder pastes. All the pastes showed a high degree of shear thinning behaviour with time. This might be due to the agglomeration of particles in the flux that prohibited paste flow under low shear rate. The action of high shear rate would break the agglomerates into smaller pieces which facilitated the flow of pastes, thus viscosity was reduced at high shear rate.
Chlorella is one of the common microalgae found in a wide range of habitats, including Antarctica. Chlorella UMACC 234 is an interesting isolate in the collection of Antarctic microalgae in the University of Malaya algae culture collection (UMACC) as it grows well at temperatures much higher than the ambience. The alga was isolated from snow samples collected from Casey, Antarctica. This study investigates the influence of nitrogen source on the growth, biochemical composition and fatty acid profile of Chlorella UMACC 234. The cultures were grown in Bold’s Basal Medium with 3.0 mM NaNO3, NH4Cl or urea. The cultures grown on NaNO3 attained the highest specific growth rate (μ = 0.43 day–1) while the specific growth rates of those grown on NH4Cl and urea were not significantly different (p > 0.05). The urea-grown cells produced the highest amounts of lipids (25.7% dry weight) and proteins (52.5% dry weight) compared to those grown on other nitrogen sources. The cell numbers attained by the cultures grown at NaNO3 levels between 0.3 and 3.0 mM were similar but decreased markedly at 9.0 mM NaNO3. The fatty acids of Chlorella UMACC 234 were dominated by saturated fatty acids, especially 16:0 and 18:0. The percentage of polyunsaturated fatty acids was very low, especially in cells grown on urea (0.9% total fatty acids). Characterisation of the growth and biochemical composition of this Antarctic Chlorella is important to our studies on the relationship of Chorella isolates from tropical, temperate and polar regions, especially in terms of phylogeny and stress adaptation.
The detection of tetrodotoxin (TTX) and saxitoxin (STX) in dried salted yellow puffer fish (Xenopterus naritus) eggs bought from Satok Market, Kuching, Sarawak was carried out by mouse bioassay method. The amount of TTX and STX detected in the samples ranged from 95.6-195.5 Mouse Unit (MU)/g and 1.72-3.58 MU/g respectively. The results indicate that the dried salted eggs samples were found to contain TTX 9-20 times above the regulatory limit for human consumption (10 MU/g). Although detected, the amount of STX in salted eggs extract was slightly below the accepted threshold limit (4 MU/g). The local public in Sarawak should be educated on the potential danger of consuming dried salted puffer fish eggs in addition to the current warnings on puffer fish.
Malaysia has adopted various strategies in developing its space sector. Indigenous space technologies would enable a sustainable growth of the space field and at the same time develop the strategic space technologies. Therefore, issues related to the current space research level are fundamentally crucial to be highlighted. Subsequently, the space focus areas can be derived in order to meet the expectations of the national and international space technology growth requirements, which are moving on to a stronger posture in R&D. In the absence of a strong R&D national space industry leadership, the Malaysian space sector remains in a traditional downstream mode of the world space technology supply chain ever since. The space technology supply chain can be divided into the ground segment and the space segment. This paper examines the current space research activities in Malaysia within the framework of the space technology supply chain. As a result, a preliminary gap in the overview of space research in Malaysia is established.
The production of ethanol, from glucose in batch and fed batch culture, was investigated. In the fed batch culture, the glucose feeding was added into the culture at 16th hour of fermentation. The effects of different glucose concentration feeding rates on ethanol fermentation were investigated for fed batch culture. The 2gL-1hr-1 glucose concentration feeding rate was found to give higher ethanol yield (2.47 g ethanol g glucose-1), with respect to substrate consumed as compared to 8 gL-1hr-1 (0.23 g ethanol g glucose-1) and 4 gL-1hr-1 (0.20 g ethanol g glucose-1). The ethanol yield with respect to substrate consumed obtained in batch culture was 0.81 g ethanol g glucose-1. The fed batch culture at 2 gL-1hr-1 glucose concentration feeding rate was proven to be a better fermentation system than the batch culture. The specific growth rate, specific glucose consumption rate and specific ethanol production rate for the fed batch fermentation, at 2 gL-1hr-1 glucose concentration feeding rate, were 0.065 hr-1, 1.20 hr-1 and 0.0009 hr-1, respectively.