The aim of this work was to study radiation and the effects of temperature on conductivity properties of polyvinyl alcohol (PVA)-based potassium hydroxide (KOH) and propylene carbonate (PC), where the ionic conduction preferentially occurs in the amorphous phase by free radicals ions through gamma-irradiation. Alkaline composite polymer electrolyte (ACPE) consisting of PVA, KOH and PC of different concentration ratios were prepared by solvent-casting technique. The ACPE were irradiated with different doses from 5 kGy up to 200 kGy. The conductivity properties of the electrolyte films were measured at different frequencies in the range 20 Hz to 1 MHz using LCR meter. The results showed that the conductivity properties were dependent on the radiation dose, temperature and the concentration of the polymer blends.
Secara geologi, kawasan Cameron Highland terdiri daripada batuan granit batolit yang merejah ke dalam batuan sedimen yang lebih tua. Rejahan jasad igneus asidik ini menyebabkan pembentukan batuan meta-sedimen dan batuan metamorfik lain sebagai sisa bumbung. Sekis sering ditemui telah mengalami luluhawa tinggi hingga sepenuhnya, berwarna kelabu cerah hingga gelap dengan butiran halus hingga sederhana dan struktur foliasi yang ketara. Manakala batuan granit mengandungi mineral kuarza, felspar dan butiran biotit dan/atau turmalin. Kebanyakan cerun potongan jalan raya yang dibina merentasi jasad batuan ini dan survei ketidakstabilan cerun dilakukan berdasarkan jenis, geometri dan cirian fiziko-kimia tanah cerun. Hasil cerapan lapangan menunjukkan bahawa jenis cerun yang gagal adalah jenis cerun tanah yang terdiri daripada jenis gelinciran cetek dan dalam. Antara faktor yang menyumbang kepada ketidakstabilan cerun adalah geometri cerun seperti cerun yang tinggi dan sudut muka cerun yang curam, sifat keperoian tanah pada cerun dan kekurangan litupan vegetasi permukaan. Ini menyebabkan permukaan cerun terdedah kepada hentaman terus hujan. Kesan daripada air larian permukaan juga menyebabkan pembentukan alur-alur hakisan pada muka cerun tanah. Sifat fiziko-kimia bahan cerun (tanah) seperti taburan saiz partikel, pH, kandungan ferum oksida, bahan organik, kandungan air, ketumpatan pukal dan sebenar serta keporosan juga didapati memainkan peranan sebagai faktor yang dalaman dalam mempengaruhi kestabilan cerun tertentu yang dikaji. Julat pH tanah yang rendah (sifat asidik) pada semua cerun mengurangkan kandungan ferum oksida dalam tanah yang bertindak sebagai bahan penyimen tanah. Ini menyebabkan agregatan tanah menjadi lemah dan mudah terhakis.
Activated carbon was prepared from coconut husk using physicochemical activation method which consisted of potassium hydroxide (KOH) treatment and carbon dioxide (CO(2)) gasification. The effects of three preparation variables (CO(2) activation temperature, CO(2) activation time and KOH:char impregnation ratio) on the 2,4,6-trichlorophenol (2,4,6-TCP) uptake and activated carbon yield were investigated. Based on the central composite design, two quadratic models were developed to correlate the preparation variables to the two responses. From the analysis of variance (ANOVA), the most influential factor on each experimental design response was identified. The activated carbon preparation conditions were optimized by maximizing both the 2,4,6-TCP uptake and activated carbon yield. The predicted 2,4,6-TCP uptake and carbon yield from the models agreed satisfactorily with the experimental values. The optimum conditions for preparing activated carbon from coconut husk for adsorption of 2,4,6-TCP were found as follow: CO(2) activation temperature of 750 degrees C, CO(2) activation time of 2.29 h and KOH:char impregnation ratio of 2.91, which resulted in 191.73 mg/g of 2,4,6-TCP uptake and 20.16 % of activated carbon yield.
Clay has been regarded as very important natural industrial materials. All these industries exploit the properties that clay can be molded into any shape and fired to dry without losing its form. A study was carried out on clay samples from eight sites in the north-eastern part of Peninsular Malaysia. The study was accomplished by using X-ray diffraction (XRD) technique. The x-ray diffraction spectra obtained enable the determination of the lattice spacing associated with the types of clay and nonclay minerals present in the samples. Results of the study shows that the major components of clay minerals present in all samples studied are kaolinite and illite. The presence of kaolinite is confirmed by firing test in which the kaolinite diffraction peaks disappeared upon heating the samples at 600 o C. The presence of non-clay minerals such as quartz, mica, feldspar and chlorite are also observed.
The present study was aimed at modifying the original formulation of Commercial Eugon agar (CEA) to develop a new H. pylori growth medium. Initial studies were carried out to determine the number of H. pylori colonies recovered on in-house H. pylori agar (IHPA), IHPA without L-cysteine and sodium sulfite (IHPA-NC), IHPA without L-cysteine (IHPA-C), IHPA without sodium sulfite (IHPA-N) and CEA as the control. Significant differences (P < 0.001) in the number of colonies recovered were observed between IHPA-N, IHPA-NC and IHPA-C. Incorporation of sodium sulfite decreased the number of colonies recovered, indicating that sodium sulfite was inhibitory to H. pylori growth. Removal of L-cysteine reduced the number of colonies recovered, suggesting that L-cysteine is necessary for the growth of H. pylori. In the subsequent study, incorporation of K(2)HPO(4) further increased the number of colonies recovered compared with IHPA-N (P < 0.001), and 0.25% (w/v) of K(2)HPO(4) yielded the highest numbers of colonies (P < or = 0.04). Finally, thirty other H. pylori clinical isolates were evaluated for their growth in the IHPAP-N, a new medium consisting of 1.5% (w/v) pepticase, 0.5% (w/v) peptone, 0.4% (w/v) sodium chloride, 0.03% (w/v) L-cysteine, 0.55% (w/v) dextrose, 0.25% (w/v) K(2)HPO(4) and 1.5% (w/v) agar. The number of colonies recovered in IHPAP-N was significantly (P < 0.005) higher than that of CEA. IHPAP-N with 0.25% K(2)HPO(4) and without sodium sulfite were adequate solid media for the growth of H. pylori.
The adsorption of phenol, from aqueous solutions on activated carbon from waste tyres, was studied in a batch system at different initial concentrations (100-500mg/L) at 30°C for 48 hours. The activated carbon was prepared using the two-step physiochemical activation, with potassium hydroxide (KOH) at ratio KOH/char = 5. The carbonization process was done at 800°C for 1 hour with nitrogen flow rate 150ml/min, followed by the activation with the carbon dioxide flow rate 150ml/min at 800°C for 2 hours. The adsorption isotherms were determined by shaking 0.1g of activated carbon with 100ml phenol solutions. The initial and final concentrations of phenol in aqueous solution were analyzed using the UV-Visible Spectrophotometer (Shimadzu, UV-1601) at a wavelength of 270nm. Experimental isotherm data were analyzed using the Langmuir and Freundlich isotherm models.The equilibrium data for phenol adsorption could fit both isotherm models well with the R2 value of 0.9774 and 0.9895, respectively. The maximum adsorption capacity of the adsorbent obtained from the Langmuir model was up to 156.25 mg/g
The land area of Tanah Putih, Gua Musang, Kelantan (Malaysia) is well-known for its wealth in industrial mineral resources, especially aluminosilicate of feldspar and mica. Natural feldspar and mica were physicochemically characterized with regard to X-ray diffraction (XRD), nitrogen sorption analysis and transmission electron microscopy (TEM) techniques for qualitative and quantitative identification of feldspar and mica. They show a good crystallinity, high surface area and uniformity of mesoporous structures. For the purpose of this experiment, the aluminosilicate of feldspar was modified either by acid treatment, or grafting the silanol groups present with various functional groups including aminopropyl-, octyl-, vinyl-, mercapto- and glycidoxy-triethoxysilanes, or activation of pre-treated support with glutaraldehyde. These support derivatives were used for further utilization in the immobilization of lipase from Candida rugosa and resulted in various interaction mechanisms between enzyme and introduced supports. It seemed that the features of the functionalized feldspar surfaces provide a preferable environmental host to enable the adsorption of lipase via interfacial adsorption method. Lipase immobilization onto feldspar support were further confirmed by scanning electron microscopy (SEM) coupled with energy dispersive X-ray microanalysis (EDX), transmission electron microscopy (TEM) and infra-red spectroscopy (FTIR) techniques. Enhancement of protein loading (up to 8.22 mg protein/g support) and immobilization yield (up to 78%) were shown by modified feldspar-lipase derivatives compared to unmodified feldspar support.
Oil palm fronds (OPF) were used to prepare activated carbon (PFAC) using physiochemical activation method, which consisted of potassium hydroxide (KOH) treatment and carbon dioxide gasification. The effects of the preparation variables, which were activation temperature, activation time and chemical impregnation ratios (KOH: char by weight), on the carbon yield and bentazon removal were investigated. Based on the central composite design (CCD), two factor interaction (2FI) and quadratic models were, respectively, employed to correlate the PFAC preparation variables to the bentazon removal and carbon yield. From the analysis of variance (ANOVA), the most influential factor on each experimental design response was identified. The optimum conditions for preparing activated carbon from OPF were found as follows: activation temperature of 850 degrees C, activation time of 1h and KOH:char ratio of 3.75:1. The predicted and experimental results for removal of bentazon and yield of PFAC were 99.85%, 20.5 and 98.1%, 21.6%, respectively.
The purpose of this in vitro study was to determine if packable resin composite with/without flowable resin composite has the ability to prevent coronal leakage in restored endodontic access openings following aging.
Redox polymerization of acrylonitrile (AN) with ethyl acrylate (EA) and fumaronitrile (FN), as comonomer and termonomer respectively, were carried out using sodium bisulfite (SBS) and potassium persulphate (KPS) as initiators at 40°C. The actual composition of monomers in copolymers and terpolymers has been characterized by gas chromatography (GC). The effects of EA and FN on the glass transition temperature (Tg) and stabilization temperature have been studied by Differential Scanning Calorimetry (DSC). The degradation behaviour and char yield were obtained by thermogravimetric analysis. Meanwhile, incorporation of 10 mol% of EA in homoPAN system was found to greatly reduce Tg to 66°C as compared to that of the homoPAN (Tg=105°C). The initial cyclization temperature (Ti) was found to be higher (264°C) in comparison to that of homoPAN (246°C). In addition, the incorporation of EA was also shown to reduce the char yield of copolymer to 40%. When FN was incorporated as termonomer, the char yield of poly(AN/EA/ FN) 90/4/6 increased up to 44% after the heat treatment with the lowest Ti (241°C).
In this study, a novel continuous reactor has been developed to produce high quality methyl esters (biodiesel) from palm oil. A microporous TiO2/Al2O3 membrane was packed with potassium hydroxide catalyst supported on palm shell activated carbon. The central composite design (CCD) of response surface methodology (RSM) was employed to investigate the effects of reaction temperature, catalyst amount and cross flow circulation velocity on the production of biodiesel in the packed bed membrane reactor. The highest conversion of palm oil to biodiesel in the reactor was obtained at 70 °C employing 157.04 g catalyst per unit volume of the reactor and 0.21 cm/s cross flow circulation velocity. The physical and chemical properties of the produced biodiesel were determined and compared with the standard specifications. High quality palm oil biodiesel was produced by combination of heterogeneous alkali transesterification and separation processes in the packed bed membrane reactor.
Rice husk (RH), an abundant by-product of rice milling, was used for the preparation of activated carbon (RHAC) via KOH and K(2)CO(3) chemical activation. The activation process was performed at the microwave input power of 600 W for 7 min. RHACs were characterized by low temperature nitrogen adsorption/desorption, scanning electron microscopy and Fourier transform infrared spectroscopy. The adsorption behavior was examined using methylene blue as adsorbate. The K(2)CO(3)-activated sample showed higher yield and better pore structures and adsorption capacity development than the KOH-activated sample, with a BET surface area, total pore volume and monolayer adsorption capacity of 1165 m(2)/g, 0.78 cm(3)/g and 441.52 mg/g, respectively. The results revealed the feasibility of microwave heating for preparation of high surface area activated carbons from rice husks via K(2)CO(3) activation.
Fatty acid methyl esters (FAME) were produced from palm oil using eggshell modified with magnesium and potassium nitrates to form a composite, low-cost heterogeneous catalyst for transesterification. The catalyst, prepared by the combination of impregnation/co-precipitation was calcined at 830 °C for 4 h. Transesterification was conducted at a constant temperature of 65 °C in a batch reactor. Design of experiment (DOE) was used to optimize the reaction parameters, and the conditions that gave highest yield of FAME (85.8%) was 5.35 wt.% catalyst loading at 4.5 h with 16:1 methanol/oil molar ratio. The results revealed that eggshell, a solid waste, can be utilized as low-cost catalyst after modification with magnesium and potassium nitrates for biodiesel production.
Layered double hydroxide (LDH) with Mg/Al molar ratio of 4/1 (MAN-4) was synthesized by co-precipitation and followed by hydrothermal method. The compound was allowed to undergo ion exchange with K2HPO4 for 48 hours to produce MgAlHPO4 (MAHP-4). The solid produced was characterized using X-ray diffraction (XRD) and Fourier Transform Infrared spectroscopy (FTIR). Adsorption of copper solution by MAHP-4 was carried out using batch experiment by mixing the copper solution and the sorbent MAHP-4. The effects of
various parameters such as contact time, pH, adsorbent dosage and initial concentration were investigated. The optimum pH for copper removal was found to be 4 and the optimum time of copper removal was found at 4 hours. The isotherm data was analysed using model isotherm Langmuir with the correlation coefficient of 0.999 was recorded. The maximum adsorption capacity, Qo (mg/g) of 142.8 mg/g was also recorded from the Langmuir isotherm. The remaining copper solution was determined by using EDXRF (Energy Dispersive XRay Fluorescence spectrometry) model MiniPal 4 (PAN analytical). The results in this study indicate that MAHP-4 has potential as an effective adsorbent for removing copper from aqueous solution.
In this work, preparation of granular activated carbon from oil palm biodiesel solid residue, oil palm shell (PSAC) by microwave assisted KOH activation has been attempted. The physical and chemical properties of PSAC were characterized using scanning electron microscopy, volumetric adsorption analyzer and elemental analysis. The adsorption behavior was examined by performing batch adsorption experiments using methylene blue as dye model compound. Equilibrium data were simulated using the Langmuir, Freundlich and Temkin isotherm models. Kinetic modeling was fitted to the pseudo-first-order, pseudo-second-order and Elovich kinetic models, while the adsorption mechanism was determined using the intraparticle diffusion and Boyd equations. The result was satisfactory fitted to the Langmuir isotherm model with a monolayer adsorption capacity of 343.94mg/g at 30°C. The findings support the potential of oil palm shell for preparation of high surface area activated carbon by microwave assisted KOH activation.
A simple, sensitive and selective HPLC method with UV detection for determination of Glipizide in human plasma was developed. Liquid-liquid extraction method was used to extract the drug from the plasma samples. Chromatographic separation of Glipizide was achieved using C18 column (ZORBAX ODS 4.6 × 150 mm). The mobile phase was comprised of 0.01 M potassium dihydrogen phosphate and acetonitrile (65:35, v/v) adjusted to pH 4.25 with glacial acetic acid. The analysis was run at a flow rate of 1.5 mL/min with an injection volume was 20 μL. The detector was operated at 275 nm. The calibration curve was linear over a concentration range of 50-1600 ng/mL. Intra-day and inter-day precision and accuracy values were below 15%. The limit of quantification was 50 ng/mL and the mean recovery was above 98%. Freeze-thaw, short-term, long-term and post-preparative stability studies showed that Glipizide in plasma sample was stable. The method may be successfully applied to analyze the Glipizide concentration in plasma samples for bioavailability and bioequivalence studies.
As a novel method of purification, an aqueous organic phase system (AOPS) was employed to purify pectinase from mango waste. The effect of different parameters, such as the alcohol concentration (ethanol, 1-propanol, and 2-propanol), the salt type and concentration (ammonium sulfate, potassium phosphate and sodium citrate), the feed stock crude load, the aqueous phase pH and NaCl concentration, were investigated in the recovery of pectinase from mango peel. The partition coefficient (K), selectivity (S), purification factor (PF) and yield (Y, %) were investigated in this study as important parameters for the evaluation of enzyme recovery. The desirable partition efficiency for pectinase purification was achieved in an AOPS of 19% (w/w) ethanol and 22% (w/w) potassium phosphate in the presence of 5% (w/w) NaCl at pH 7.0. Based on the system, the purification factor of pectinase was enhanced 11.7, with a high yield of 97.1%.
The potential of solar cells have not been fully tapped due to the lack of energy conversion efficiency. There are three important mechanisms in producing high efficiency cells to harvest solar energy; reduction of light reflectance, enhancement of light trapping in the cell and increment of light absorption. The current work represent studies conducted in surface modification of single-crystalline silicon solar cells using wet chemical etching techniques. Two etching types are applied; alkaline etching (KOH:IPA:DI) and acidic etching (HF:HNO3:DI). The alkaline solution resulted in anisotropic profile that leads to the formation of inverted pyramids. While acidic solution formed circular craters along the front surface of silicon wafer. This surface modification will leads to the reduction of light reflectance via texturizing the surface and thereby increases the short circuit current and conversion rate of the solar cells.
In this letter, we investigate the fabrication of Silicon nanostructure patterned on lightly doped (10(15) cm(-3)) p-type silicon-on-insulator by atomic force microscope nanolithography technique. The local anodic oxidation followed by two wet etching steps, potassium hydroxide etching for silicon removal and hydrofluoric etching for oxide removal, are implemented to reach the structures. The impact of contributing parameters in oxidation such as tip materials, applying voltage on the tip, relative humidity and exposure time are studied. The effect of the etchant concentration (10% to 30% wt) of potassium hydroxide and its mixture with isopropyl alcohol (10%vol. IPA ) at different temperatures on silicon surface are expressed. For different KOH concentrations, the effect of etching with the IPA admixture and the effect of the immersing time in the etching process on the structure are investigated. The etching processes are accurately optimized by 30%wt. KOH +10%vol. IPA in appropriate time, temperature, and humidity.
Proteases in ginger rhizome have the potentials in industrial applications. This study was conducted to extract and characterize the proteolytic enzyme from ginger (Zingiber officinale Roscoe). Ginger protease (GP) was extracted from ginger rhizome by homogenization with 100 mM potassium phosphate buffer pH 7.0 containing 10 mM cysteine and 5 mM EDTA which were found to be the most efficient extraction buffer and stabilizers. After centrifugation at 10,500 x g, protein in the crude extract was precipitated using 60% ammonium sulfate following which the precipitate was redissolved in 50 mM potassium phosphate buffer pH 7.0, dialyzed and then lyophilized. The extraction method yielded 0.94% (w/w of fresh weight) of GP with a specific activity of 27.6 ± 0.1 Unit/mg protein where 1 Unit is defined as the amount of protease causing an increase in absorbance by 1 unit per minute using azocasein as the substrate. Results show that the GP was completely inhibited by heavy metal cations i.e. Cu2+and Hg2+, and a thiol blocking agent or inhibitor, n-ethyl maleimide (NEM), indicating that GP is most probably a cysteine protease. The enzyme has an optimum temperature at 60⁰C and the optimum pH ranged between pH 6 to 8. Monovalent cations (K+ and Na+) have no significant effect on activity of GP, but divalent and trivalent cations showed moderate inhibitory effect. Detergents such as sodium dodecyl sulfate increased the activity of GP while Tween 80 and Tween 20 slightly reduced the activity.