MyMedR

Displaying publications 181 - 200 of 288 in total

Abstract:

Sort:

Anticorrosive properties of nano silicate from paddy husk in salt medium

Norinsan Kamil Othman, Solhan Yahya, Denni Asra Awizar

Sains Malaysiana, 2016;45:1253-1258.

Anticorrosive properties of nano silicate from paddy husk in salt medium was investigated via weight loss method, Tafel
polarization and impedance techniques. Prior to the corrosion test, the silica powder was obtained from burning the
rice husk and extended with a chemical treatment process. The size of silica powder was characterized via zeta sizer and
showed the amount of micro silica particle appear more than the nano size particle. Nano silica powder was produced
from the refluxing process of micro silica to enhance the good properties of silica particle. The corrosion inhibition
efficiency of nano silicate showed good inhibition with increased in inhibitor concentrations. Weight loss test exhibits
high inhibition as more than 80% even, immersed in the corrosive medium until 14 days. The nano silicate inhibitor
affected the anodic reaction as showed by Tafel plot analysis. Impedance results also correlated with other test as shown
by the large size of Nyquist semicircle which represents as high resistance of charge transfer. The surface morphology
of inhibited specimen showed a smooth surface after nano silicate inhibitor applied in the NaCl medium as observed
through scanning electron microscopy (SEM) and energy-dispersive x-ray spectroscopy (EDX).

Matched MeSH terms: Sodium Chloride
Captan utilization by a soil bacterium planomicrobium flavidum strain EF

Eman Mohamed, Fatma Ahmad Mostafa

Sains Malaysiana, 2018;47:85-89.

The fungicide captan, which is commonly used to control fungal diseases in many plants, causes soil infertility and cancer to human beings. Hence, this fungicide was tested for utilization as a sole carbon source by a newly soil isolate, Planomicrobium flavidum strain EF. This bacterium resists captan up to 2000 ppm and showed higher growth patterns in minimum salt medium supplemented with captan only, if compared with minimum salt medium without captan. Moreover, almost 77.5% of captan has been utilized by Planomicrobiu flavidum after only 2 h of growth under shaking conditions and only 0.8% of the fungicide was remained after 24 h of bacterial growth. Captan residues in both soil samples and minimal salt medium were accurately estimated using GC-ECD (gas chromatography - electron detector) and GC-MS/MS (gas chromatography - mass spectrum) technologies. According to current results, Planomicrobium flavidum strain EF is highly recommended for captan and may be other fungicides bioremediation.

Matched MeSH terms: Sodium Chloride, Dietary
Fulltext High-quality RNA isolation from pigment-rich Dendrobium flowers

Khairul-Anuar MA, Mazumdar P, Lau SE, Tan TT, Harikrishna JA

3 Biotech, 2019 Oct;9(10):371.
PMID: 31588395 DOI: 10.1007/s13205-019-1898-y

Isolation of high-quality RNA from Dendrobium flowers is challenging because of the high levels of pigment, polysaccharides, and polyphenols. In the present study, an efficient CTAB method for RNA extraction from the pigment-rich flowers of Dendrobium was optimised. The optimised method yielded high quantities of RNA (10.1-12.9 µg/g). Spectrophotometric values of A260/280 in the range of 2.2 to 2.4 and A260/230 values of 2.0 suggested that the isolated RNA was free of polyphenols, polysaccharides, and protein contaminants. RNA integrity numbers determined by microfluidics were in the range of 7.9-8.9 indicative of intact RNA. In the improved method, the addition of 3 M NaCl and 3% PVP-10 in the extraction buffer, followed by an incubation period of 45 min at 65 °C, eliminated most of the polysaccharides, polyphenolic compounds, and denatured protein. Extraction with phenol:chloroform:isoamyl alcohol (125:24:1) effectively removed pigments from the aqueous phase, while the precipitation of RNA with lithium chloride minimised the co-precipitation of protein, DNA, and polysaccharide and resulted in the extraction of high quality of RNA. The suitability of the RNA for downstream processing was confirmed via RT-PCR amplification of Chalcone synthase gene from cDNA prepared from RNA isolated from different developmental stages of the flower of a Dendrobium hybrid. The present method will be highly useful for the isolation of RNA from pigment, polyphenol, and polysaccharide-rich plant tissues.

Matched MeSH terms: Sodium Chloride
Fulltext Computerized Morphometric Analysis of Eryptosis

Jacob SS, Prasad K, Rao P, Kamath A, Hegde RB, Baby PM, et al.

Front Physiol, 2019;10:1230.
PMID: 31649550 DOI: 10.3389/fphys.2019.01230

Eryptosis is the suicidal destruction-process of erythrocytes, much like apoptosis of nucleated cells, in the course of which the stressed red cell undergoes cell-shrinkage, vesiculation and externalization of membrane phosphatidylserine. Currently, there exist numerous methods to detect eryptosis, both morphometrically and biochemically. This study aimed to design a simple but sensitive, automated computerized approach to instantaneously detect eryptotic red cells and quantify their hallmark morphological characteristics. Red cells from 17 healthy volunteers were exposed to normal Ringer and hyperosmotic stress with sodium chloride, following which morphometric comparisons were conducted from their photomicrographs. The proposed method was found to significantly detect and differentiate normal and eryptotic red cells, based on variations in their structural markers. The receiver operating characteristic curve analysis for each of the markers showed a significant discriminatory accuracy with high sensitivity, specificity and area under the curve values. The software-based technique was then validated with RBCs in malaria. This model, quantifies eryptosis morphometrically in real-time, with minimal manual intervention, providing a new window to explore eryptosis triggered by different stressors and diseases and can find wide application in laboratories of hematology, blood banks and medical research.

Matched MeSH terms: Sodium Chloride
Biosynthesis of butyl esters from crude oil of palm fruit and kernel using halophilic lipase secretion by Marinobacter litoralis SW-45

Musa H, Kasim FH, Gunny AAN, Gopinath SCB, Ahmad MA

3 Biotech, 2019 Aug;9(8):314.
PMID: 31406636 DOI: 10.1007/s13205-019-1845-y

Initially, a new moderate halophilic strain was locally isolated from seawater. The partial 16S rRNA sequence analysis positioned the organism in Marinobacter genus and was named 'Marinobacter litoralis SW-45'. This study further demonstrates successful utilization of the halophilic M. litoralis SW-45 lipase (MLL) for butyl ester synthesis from crude palm fruit oil (CPO) and kernel oil (CPKO) in heptane and solvent-free system, respectively, using hydroesterification. Hydrolysis and esterification of enzymatic [Thermomyces lanuginosus lipase (TLL)] hydrolysis of CPO and CPKO to free fatty acids (FFA) followed by MLL-catalytic esterification of the concentrated FFAs with butanol (acyl acceptor) to synthesize butyl esters were performed. A one-factor-at-a-time technique (OFAT) was used to study the influence of physicochemical factors on the esterification reaction. Under optimal esterification conditions of 40 and 45 °C, 150 and 230 rpm, 50% (v/v) biocatalyst concentration, 1:1 and 5:1 butanol:FFA, 9% and 15% (w/v) NaCl, 60 and 15 min reaction time for CPO- and CPKO-derived FFA esterification system, maximum ester conversion of 62.2% and 69.1%, respectively, was attained. Gas chromatography (GC) analysis confirmed the products formed as butyl esters. These results showed halophilic lipase has promising potential to be used for biosynthesis of butyl esters in oleochemical industry.

Matched MeSH terms: Sodium Chloride
Haloadaptation: insights from comparative modeling studies between halotolerant and non-halotolerant dehalogenases

Edbeib MF, Aksoy HM, Kaya Y, Wahab RA, Huyop F

J Biomol Struct Dyn, 2020 Aug;38(12):3452-3461.
PMID: 31422756 DOI: 10.1080/07391102.2019.1657498

Halophiles are extremophilic microorganisms that grow optimally at high salt concentrations by producing a myriad of equally halotolerant enzymes. Structural haloadaptation of these enzymes adept to thriving under high-salt environments, though are not fully understood. Herein, the study attempts an in silico investigation to identify and comprehend the evolutionary structural adaptation of a halotolerant dehalogenase, DehHX (GenBank accession number: KR297065) of the halotolerant Pseudomonas halophila, over its non-halotolerant counterpart, DehMX1 (GenBank accession number KY129692) produced by Pseudomonas aeruginosa. GC content of the halotolerant DehHX DNA sequence was distinctively higher (58.9%) than the non-halotolerant dehalogenases (55% average GC). Its acidic residues, Asp and Glu were 8.27% and 12.06%, respectively, compared to an average 5.5% Asp and 7% Glu, in the latter; but lower contents of basic and hydrophobic residues in the DehHX. The secondary structure of DehHX interestingly revealed a lower incidence of α-helix forming regions (29%) and a higher percentage of coils (57%), compared to 49% and 29% in the non-halotolerant homologues, respectively. Simulation models showed the DehHX is stable under a highly saline environment (25% w/v) by adopting a highly negative-charged surface with a concomitant weakly interacting hydrophobic core. The study thus, established that a halotolerant dehalogenase undergoes notable evolutionary structural changes related to GC content over its non-halotolerant counterpart, in order to adapt and thrive under highly saline environments.Communicated by Ramaswamy H. Sarma.

Matched MeSH terms: Sodium Chloride
Fulltext Optimization of culture conditions for Mpt64 synthetic gene expression in Escherichia coli BL21 (DE3) using surface response methodology

Kusuma SAF, Parwati I, Rostinawati T, Yusuf M, Fadhlillah M, Ahyudanari RR, et al.

Heliyon, 2019 Nov;5(11):e02741.
PMID: 31844694 DOI: 10.1016/j.heliyon.2019.e02741

MPT64 is a specific protein that is secreted by Mycobacterium tuberculosis complex (MTBC). The objective of this study was to obtain optimum culture conditions for MPT64 synthetic gene expression in Escherichia coli BL21 (DE3) by response surface methodology (RSM). The RSM was undertaken to optimize the culture conditions under different cultivation conditions (medium concentration, induction time and inducer concentration), designed by the factorial Box-Bhenken using Minitab 17 statistical software. From the randomized combination, 15 treatments and three center point repetitions were obtained. Furthermore, expression methods were carried out in the flask scale fermentation in accordance with the predetermined design. Then, the MPT64 protein in the cytoplasm of E. coli cell was isolated and characterized using sodium dodecyl sulfate polyacrilamide electrophoresis (SDS-PAGE) then quantified using the ImageJ program. The optimum conditions were two-fold medium concentration (tryptone 20 mg/mL, yeast extract 10 mg/mL, and sodium chloride 20 mg/mL), 5 h of induction time and 4 mM rhamnose. The average concentration of recombinant MPT64 at optimum conditions was 0.0392 mg/mL, higher than the predicted concentration of 0.0311 mg/mL. In conclusion, the relationship between the selected optimization parameters strongly influenced the level of MPT64 gene expression in E. coli BL21 (DE3).

Matched MeSH terms: Sodium Chloride
Fulltext Application of Biochar Derived From Pyrolysis of Waste Fiberboard on Tetracycline Adsorption in Aqueous Solution

Xu D, Gao Y, Lin Z, Gao W, Zhang H, Karnowo K, et al.

Front Chem, 2019;7:943.
PMID: 32117859 DOI: 10.3389/fchem.2019.00943

In this study, biochars derived from waste fiberboard biomass were applied in tetracycline (TC) removal in aqueous solution. Biochar samples were prepared by slow pyrolysis at 300, 500, and 800°C, and were characterized by ultimate analysis, Fourier transform infrared (FTIR), scanning electron microscopy (SEM), X-ray photoelectron spectroscopy (XPS), Brunauer-Emmett-Teller (BET), etc. The effects of ionic strength (0-1.0 mol/L of NaCl), initial TC concentration (2.5-60 ppm), biochar dosage (1.5-2.5 g/L), and initial pH (2-10) were systemically determined. The results present that biochar prepared at 800°C (BC800) generally possesses the highest aromatization degree and surface area with abundant pyridinic N (N-6) and accordingly shows a better removal efficiency (68.6%) than the other two biochar samples. Adsorption isotherm data were better fitted by the Freundlich model (R2 is 0.94) than the Langmuir model (R2 is 0.85). Thermodynamic study showed that the adsorption process is endothermic and mainly physical in nature with the values of ΔH0 being 48.0 kJ/mol, ΔS0 being 157.1 J/mol/K, and ΔG0 varying from 1.02 to -2.14 kJ/mol. The graphite-like structure in biochar enables the π-π interactions with a ring structure in the TC molecule, which, together with the N-6 acting as electron donor, is the main driving force of the adsorption process.

Matched MeSH terms: Sodium Chloride
Fulltext Two-Step Purification of Glycerol as a Value Added by Product From the Biodiesel Production Process

Abdul Raman AA, Tan HW, Buthiyappan A

Front Chem, 2019;7:774.
PMID: 31799239 DOI: 10.3389/fchem.2019.00774

For every ton of biodiesel produced, about 100 kg of glycerol is also generated as a by-product. The traditional method of removing glycerol is mainly by gravity separation or centrifugation. This method generates crude glycerol, which may still contain impurities such as methanol, oil, soap, salt, and other organic materials at ppm levels. The effective usage of crude glycerol is important to improve the economic sustainability of the biodiesel industry while reducing the environmental impacts caused by the generated waste. The application and value of crude glycerol can be enhanced if these impurities are removed or minimized. Thus, it is important to develop a method which can increase the economic and applicable value of crude glycerol. Therefore, in the present study, the dual step purification method comprised of acidification and ion exchange techniques has been used to purify the crude glycerol and convert it into higher-value products. The acidification process started with the pH adjustment of the crude glycerol, using phosphoric acid to convert soap into fatty acid and salts. Then, the pretreated glycerol was further purified by ion exchange with a strong cation H+ resin. Gas chromatography (GC) was used to analyze both crude and purified glycerol and expressed as the weight percentage of glycerol content. A maximum glycerol purity of 98.2% was obtained after the dual step purification method at the optimized conditions of 60% of solvent, the flow rate of 15 mL/min and 40 g of resin. Further, the glycerol content measured being within the accepted amount of BS 2621:1979. Therefore, this study has proven that the proposed crude glycerol purification process is effective in improving the glycerol purity and could enhance the applicability of glycerol in producing value-added products which bring new revenue to the biodiesel industry.

Matched MeSH terms: Sodium Chloride, Dietary
Fulltext Role of Phase-Dependent Dielectric Properties of Alumina Nanoparticles in Electromagnetic-Assisted Enhanced Oil Recovery

Adil M, Lee KC, Zaid HM, Manaka T

Nanomaterials (Basel), 2020 Oct 06;10(10).
PMID: 33036153 DOI: 10.3390/nano10101975

The utilization of metal-oxide nanoparticles in enhanced oil recovery (EOR) has generated considerable research interest to increase the oil recovery. Among these nanoparticles, alumina nanoparticles (Al2O3-NPs) have proved promising in improving the oil recovery mechanism due to their prominent thermal properties. However, more significantly, these nanoparticles, coupled with electromagnetic (EM) waves, can be polarized to reduce water/oil mobility ratio and create disturbances at the oil/nanofluid interface, so that oil can be released from the reservoir rock surfaces and travelled easily to the production well. Moreover, alumina exists in various transition phases (γ, δ, θ, κ, β, η, χ), providing not only different sizes and morphologies but phase-dependent dielectric behavior at the applied EM frequencies. In this research, the oil recovery mechanism under EM fields of varying frequencies was investigated, which involved parameters such as mobility ratio, interfacial tension (IFT) and wettability. The displacement tests were conducted in water-wet sandpacks at 95 °C, by employing crude oil from Tapis. Alumina nanofluids (Al2O3-NFs) of four different phases (α, κ, θ and γ) and particle sizes (25-94.3 nm) were prepared by dispersing 0.01 wt. % NPs in brine (3 wt. % NaCl) together with SDBS as a dispersant. Three sequential injection scenarios were performed in each flooding scheme: (i) preflushes brine as a secondary flooding, (ii) conventional nano/EM-assisted nanofluid flooding, and (iii) postflushes brine to flush NPs. Compared to conventional nanofluid flooding (3.03-11.46% original oil in place/OOIP) as incremental oil recovery, EM-assisted nanofluid flooding provided an increase in oil recovery by approximately 4.12-12.90% of OOIP for different phases of alumina. It was established from these results that the recovery from EM-assisted nanofluid flooding is itself dependent on frequency, which is associated with good dielectric behavior of NPs to formulate the oil recovery mechanism including (i) mobility ratio improvement due to an electrorheological (ER) effect, (ii) interfacial disturbances by the oil droplet deformation, and (iii) wettability alteration by increased surface-free energy.

Matched MeSH terms: Sodium Chloride
Fulltext Neutron-activated biodegradable samarium-153 acetylacetonate-poly-L-lactic acid microspheres for intraarterial radioembolization of hepatic tumors

Wong YH, Tan HY, Kasbollah A, Abdullah BJJ, Acharya RU, Yeong CH

World J Exp Med, 2020 Mar 30;10(2):10-25.
PMID: 32266125 DOI: 10.5493/wjem.v10.i2.10

BACKGROUND: Liver cancer is the 6th most common cancer in the world and the 4th most common death from cancer worldwide. Hepatic radioembolization is a minimally invasive treatment involving intraarterial administration of radioembolic microspheres.
AIM: To develop a neutron-activated, biodegradable and theranostics samarium-153 acetylacetonate (153SmAcAc)-poly-L-lactic acid (PLLA) microsphere for intraarterial radioembolization of hepatic tumors.
METHODS: Microspheres with different concentrations of 152SmAcAc (i.e., 100%, 150%, 175% and 200% w/w) were prepared by solvent evaporation method. The microspheres were then activated using a nuclear reactor in a neutron flux of 2 × 1012 n/cm2/s1, converting 152Sm to Samarium-153 (153Sm) via152Sm (n, γ) 153Sm reaction. The SmAcAc-PLLA microspheres before and after neutron activation were characterized using scanning electron microscope, energy dispersive X-ray spectroscopy, particle size analysis, Fourier transform infrared spectroscopy, thermo-gravimetric analysis and gamma spectroscopy. The in-vitro radiolabeling efficiency was also tested in both 0.9% sodium chloride solution and human blood plasma over a duration of 550 h.
RESULTS: The SmAcAc-PLLA microspheres with different SmAcAc contents remained spherical before and after neutron activation. The mean diameter of the microspheres was about 35 µm. Specific activity achieved for 153SmAcAc-PLLA microspheres with 100%, 150%, 175% and 200% (w/w) SmAcAc after 3 h neutron activation were 1.7 ± 0.05, 2.5 ± 0.05, 2.7 ± 0.07, and 2.8 ± 0.09 GBq/g, respectively. The activity of per microspheres were determined as 48.36 ± 1.33, 74.10 ± 1.65, 97.87 ± 2.48, and 109.83 ± 3.71 Bq for 153SmAcAc-PLLA microspheres with 100%, 150%, 175% and 200% (w/w) SmAcAc. The energy dispersive X-ray and gamma spectrometry showed that no elemental and radioactive impurities present in the microspheres after neutron activation. Retention efficiency of 153Sm in the SmAcAc-PLLA microspheres was excellent (approximately 99%) in both 0.9% sodium chloride solution and human blood plasma over a duration of 550 h.
CONCLUSION: The 153SmAcAc-PLLA microsphere is potentially useful for hepatic radioembolization due to their biodegradability, favorable physicochemical characteristics and excellent radiolabeling efficiency. The synthesis of the formulation does not involve ionizing radiation and hence reducing the complication and cost of production.

Matched MeSH terms: Sodium Chloride
Fulltext Magnetic nanoparticles assisted dispersive liquid-liquid microextraction of chloramphenicol in water samples

Saad SM, Aling NA, Miskam M, Saaid M, Mohamad Zain NN, Kamaruzaman S, et al.

R Soc Open Sci, 2020 Apr;7(4):200143.
PMID: 32431904 DOI: 10.1098/rsos.200143

This work describes the development of a new methodology based on magnetic nanoparticles assisted dispersive liquid-liquid microextraction (DLLME-MNPs) for preconcentration and extraction of chloramphenicol (CAP) antibiotic residues in water. The approach is based on the use of decanoic acid as the extraction solvent followed by the application of MNPs to magnetically retrieve the extraction solvent containing the extracted CAP. The coated MNPs were then desorbed with methanol, and the clean extract was analysed using ultraviolet-visible spectrophotometry. Several important parameters, such as the amount of decanoic acid, extraction time, stirring rate, amount of MNPs, type of desorption solvent, salt addition and sample pH, were evaluated and optimized. Optimum parameters were as follows: amount of decanoic acid: 200 mg; extraction time: 10 min; stirring rate: 800 rpm; amount of MNPs: 60 mg; desorption solvent: methanol; salt: 10%; and sample pH, 8. Under the optimum conditions, the method demonstrated acceptable linearity (R2 = 0.9933) over a concentration range of 50-1000 µg l-1. Limit of detection and limit of quantification were 16.5 and 50.0 µg l-1, respectively. Good analyte recovery (91-92.7%) and acceptable precision with good relative standard deviations (0.45-6.29%, n = 3) were obtained. The method was successfully applied to tap water and lake water samples. The proposed method is rapid, simple, reliable and environmentally friendly for the detection of CAP.

Matched MeSH terms: Sodium Chloride
Fulltext One-step synthesis of zwitterionic graphene oxide nanohybrid: Application to polysulfone tight ultrafiltration hollow fiber membrane

Syed Ibrahim GP, Isloor AM, Ismail AF, Farnood R

Sci Rep, 2020 04 23;10(1):6880.
PMID: 32327672 DOI: 10.1038/s41598-020-63356-2

In this paper, novel zwitterionic graphene oxide (GO) nanohybrid was synthesized using monomers [2-(Methacryloyloxy)ethyl]dimethyl-(3-sulfopropyl)ammonium hydroxide (SBMA) and N,N'-methylenebis(acrylamide) (MBAAm) (GO@poly(SBMA-co-MBAAm), and incorporated into polysulfone (PSF) hollow fiber membrane for the effectual rejection of dye from the wastewater. The synthesized nanohybrid was characterized using FT-IR, PXRD, TGA, EDX, TEM and zeta potential analysis. The occurrence of nanohybrid on the membrane matrix and the elemental composition were analyzed by XPS. The as-prepared tight ultrafiltration hollow fiber membrane exhibited high rejection of reactive black 5 (RB-5, 99%) and reactive orange 16 (RO-16, 74%) at a dye concentration of 10 ppm and pure water flux (PWF) of 49.6 L/m2h. Fabricated nanocomposite membranes were also studied for their efficacy in the removal of both monovalent (NaCl) and divalent salts (Na2SO4). The results revealed that the membrane possesses complete permeation to NaCl with less rejection of Na2SO4 (<5%). In addition, the nanocomposite membrane revealed outstanding antifouling performance with the flux recovery ratio (FRR) of 73% towards bovine serum albumin (BSA). Therefore, the in-house prepared novel nanocomposite membrane is a good candidate for the effective decolorization of wastewater containing dye.

Matched MeSH terms: Sodium Chloride
A novel wound healing accelerator: Effect of vitreous gel of cow eyeball on a chronic wound model

Makhmudi A, Wirohadidjojo YW, Gahara E, Noor HZ, Sunardi M, Mahmudah NA, et al.

Med J Malaysia, 2020 11;75(6):698-704.
PMID: 33219180

INTRODUCTION: Several studies have reported the disturbance in the process of wound healing after administration of mitomycin-C, which inhibits granulation tissue formation and collagen synthesis, resulting in chronic wounds. The vitreous gel of cow eyeballs contains a high level of hyaluronic acid, which has a role in inflammation, granulation, re-epithelialization, and remodelling. This study aims to understand the effect of 1% povidone iodine and vitreous gel of cow eyeballs on wound healing after administration of mitomycin-C.
METHODS: This was an in vivo study with quasi-experimental methods on 32 Wistar mice. Full-thickness wounds were made and then treated with mitomicyn-C. The mice were divided into 4 groups: a control group with NaCl 0.9% vitreous gel of cow eyeball (VGCE), 1% povidone-iodine, and a combination of VGCE and 1% povidone-iodine groups. Macroscopic and microscopic observations of the process of wound healing were performed on days 3, 7, and 14.
RESULTS: Vitreous gel administration produced significant wound healing rates within the first three days, and histological analysis revealed an increased number of fibroblasts and polymorphonuclear cells. However, the povidone iodine group and the combination group with vitreous gel did not produce significant results.
CONCLUSION: The single administration of VGCE can accelerate the wound healing process, increase the number of fibroblasts, and reduce inflammation in a chronic wound model.

Matched MeSH terms: Sodium Chloride
Thermal Behavior of Selected Starches in Presence of Other Food Ingredients Studied by Differential Scanning Calorimetery (DSC)-Review

Elgadir MA, Bakar J, Zaidul ISM, Rahman RA, Abbas KA, Hashim DM, et al.

Compr Rev Food Sci Food Saf, 2009 Jul;8(3):195-201.
PMID: 33467796 DOI: 10.1111/j.1541-4337.2009.00078.x

This review article highlights the thermal behaviors of selected starches that were studied using differential scanning calorimetery (DSC) with data shown in various research publications. The starches of sago, potato, sweet potato, cassava, yam, and corn are included in this overview. Our examinations indicate that thermal properties are highly affected by the type of starch, its amylose/amylopectin content, and the presence of other food ingredients such as sugar, sodium chloride, water, milk, hydrocolloids, and meat. When the heating temperatures of the starches were increased, the DSC measurements also showed an increase in the temperatures of the gelatinization (onset [To ], peak [Tp ], and conclusion [Tc ]). This may be attributed to the differences in the degree of crystallinity of the starch, which provides structural stability and makes the granule more resistant to gelatinization.

Matched MeSH terms: Sodium Chloride
Fulltext Optimization and validation of a method for extraction and quantification of ochratoxin A in black pepper

Jalili, Maryam, Jinap, S.

International Food Research Journal, 2015;22(2):502-509.
MyJurnal

The extraction method for the determination of ochratoxin A (OTA) in black pepper was optimized. The influence of three variables, i.e., type of solvent, solvent-volume-to-sample- size ratio (v/w) and amount of sodium chloride (NaCl) (g), on OTA recovery was evaluated. Analysis of variance was used to compare recovery values obtained from different solvents, and response surface methodology (RSM) was used to determine the optimum amount of NaCl and the solvent-volume-to-sample-size ratio. The concentration of OTA was determined by high-performance liquid chromatography with fluorescence detection. The highest recovery (95.2 %) was obtained when methanol/water (80:20, v/v) was used as the solvent. The RSM results showed that the experimental data could be adequately fitted to a second-order polynomial model with multiple regression coefficients (R2) of 0.962. The optimum amount of NaCl was determined to be 3 g, whereas the optimum solvent-volume-to-sample-size ratio (v/w) was found to be 4. The proposed method was applied to 20 samples, and the presence of OTA was found in 8 (40%) samples ranging from 0.11 to 3.16 ng g-1.

Matched MeSH terms: Sodium Chloride
Magnetized graphene layers synthesized on the carbon nanofibers as novel adsorbent for the extraction of polycyclic aromatic hydrocarbons from environmental water samples

Rezvani-Eivari M, Amiri A, Baghayeri M, Ghaemi F

J Chromatogr A, 2016 Aug 16.
PMID: 27578405 DOI: 10.1016/j.chroma.2016.08.034

The application of magnetized graphene (G) layers synthesized on the carbon nanofibers (CNFs) (m-G/CNF) was investigated as novel adsorbent for the magnetic solid-phase extraction (MSPE) of polycyclic aromatic hydrocarbons (PAHs) in water samples followed by gas chromatography-flame ionization detector (GC-FID). Six important parameters, affecting the extraction efficiency of PAHs, including: amount of adsorbent, adsorption and desorption times, type and volume of the eluent solvent and salt content of the sample were evaluated. The optimum extraction conditions were obtained as: 5min for extraction time, 20mg for sorbent amount, dichloromethane as desorption solvent, 1mL for desorption solvent volume, 5min for desorption time and 15% (w/v) for NaCl concentration. Good performance data were obtained at the optimized conditions. The calibration curves were linear over the concentration ranges from 0.012 to 100ngmL(-1) with correlation coefficients (r) between 0.9950 and 0.9967 for all the analytes. The limits of detection (LODs, S/N=3) of the proposed method for the studied PAHs were 0.004-0.03ngmL(-1). The relative standard deviations (RSDs) for five replicates at two concentration levels (0.1 and 50ngmL(-1)) of PAHs were ranged from 3.4 to 5.7%. Appropriate relative recovery values, in the range of 95.5-99.9%, were also obtained for the real water sample analysis.

Matched MeSH terms: Sodium Chloride
Fulltext Endemic goitre: a preventable and yet highly prevalent disease in Sarawak (letter)

Tan YK

Med J Malaysia, 1982 Mar;37(1):96-7.
PMID: 7121358

Comment on: Chen PC. Endemic goitre: a preventable and yet highly prevalent disease in
Sarawak. Med J Malaysia. 1981 Jun;36(2):67-9

Matched MeSH terms: Sodium Chloride
Fulltext The prevalence of endemic goitre among Penans of the Baram

Chen PC, Yap SB

Med J Malaysia, 1988 Jun;43(2):159-61.
PMID: 3266288
Matched MeSH terms: Sodium Chloride
Fulltext Occurance of enterococci in root canals and in the immediate clinical environment

Che Ab Aziz, Z.A., Baharin, S.A., Spratt, D., Gulabivala, K.

Ann Dent, 2009;16(1):1-8.
MyJurnal

This study aimed to detect the presence of enterococci in the root canals of untreated and treated teeth with periapical disease and to compare this to their presence in the saliva and in the immediate surgical environment during root canal treatment. Using an aseptic technique, 33 samples were obtained from 27 untreated and 6 previously treated teeth associated with apical periodontitis. Reduced Transport Fluid (RTF) was used as transport medium. Saliva samples and areas in the surgical environment were also sampled. These were performed prior to chemo-mechanical debrjdement and obturation for every case. The saliva was diluted to 10- J and was plated on Bile Aesculin Azide (BEA) agar whereas the rest of the samples were plated on Bile Aesculin (BE) agar. These plates were then incubated aerobically at 37°C for 48 hours. All the colony types that blackened the agar were sub-cultured to obtain pure isolates and tested on 6.5% sodium chloride (NaCI). Growth on this medium was Gram stained for further confirmation of cell morphology. Gram positive cocci isolated from previous positive test were identified as enterococci. Enterococci were recovered from untreated cases only; from 2 teeth (in 2 patients) prior to chemo-mechanical debridement, from 3 teeth (in 3 patients) prior to obturation and I from saliva sample. A 'total of 5 samples from 5 different patients were positive for enteroco•cci. Sampling in the immediate surgical environment revealed a low occurence in the range of3.0% (1/33) to 15_2% (5/33). In conclusion, the occurence of enterococci in patients and the immediate surgical environment was low number.

Matched MeSH terms: Sodium Chloride

Filters

Please provide feedback to Administrator (afdal@afpm.org.my)

External Links