Displaying publications 241 - 260 of 343 in total

Abstract:
Sort:
  1. Fulltext Sustainable green interlocking pavement block
    Umar Kassim, Omar Mohd Rohim
    Journal of Advanced Research in Applied Sciences and Engineering Technology, 2017;8(1):1-7.
    MyJurnal
    In accordance upon conservation efforts, this research emphasizes on prevention of
    environmental pollution and considers the elements of sustainable of infrastructure
    construction materials, which is interlocking pavement block. The development of this
    innovative product apply the concept of 3Rs and waste to wealth by using the
    agricultural waste product, coconut shell, where widely available with very minimum
    cost worldwide especially in tropical country such as India, Indonesia, Philippines,
    Thailand and Malaysia. The main objective of this research is to produce an
    environmental friendly product with a good quality, low cost and lightweight known as
    Green Interlocking Pavement (GIP Block). The chemical composition of coconut shell
    ash and ordinary Portland cement being identified and compared to know whether it
    is able to react as a good binder in the mixture or not. The quality of GIP Block
    considered is compressive strength, water absorption and bulk density. All the blocks
    were curing in seven and 28 days before implementing the entire test. The existing
    interlocking pavement used as bench mark and GIP Block 0% of proportion of coconut
    shell ash used as control variables. The specimen of the interlocking pavement
    prepared in this research is 10%, 20% and 30% proportion of coconut shell ash to
    partially replace the quantity of cement. The ratio of the interlocking pavement apply
    in this research is 1:2 which stand for one part cement and two part of sand. The
    findings withdrawn from this research are: first, the chemical characteristic of the
    coconut shell ash and cement. Second, the value of bulk density slightly reduces as the
    percentage of coconut shell ash increases. Third, the additional of coconut shell ash to
    partially replace the quantity of cement in the product reduce the compressive
    strength and increase the percentage of water absorption.
    Matched MeSH terms: Silicon Dioxide
  2. Fulltext Biocompatibility assessment of fabricated melt-derived 45S5 bioactive glass on dental cells proliferation
    Mohd Zain N.S., Tajudin S.S., Mohd Noor S.N.F., Mohamad H.
    Journal of Biomedical and Clinical Sciences, 2016;1(1):26-32.
    MyJurnal
    Thisstudy aim tocharacterize melt-derivedbioactive glass and to determinethe bioactive glass (BG) suitability for dental usagethrough proliferative activity assessment of stem cells from human exfoliated deciduous teeth (SHED)when exposed to bioactive glass conditioned medium. Bioglass 45S5 in mole percentages (46.13% SiO2, 26.91% CaO, 24.35% Na2O and 2.60% P2O5)was synthesizedthrough melt-derived and characterized usingX-ray diffraction (XRD) and Fourier transform infrared spectroscopy (FTIR)to confirm and identify its properties.SHEDwere used to evaluate the biocompatibility of 45S5 by exposing the cells to various concentration of BG-conditioned medium (1-10 mg/ml) using alamarBlue assay. The BG produced has an amorphous structureas shown by XRD analysis. TheSi-O-Si bending, asymmetric Si-O stretching and asymmetricSi-O-Si stretchingbands were observed in the BG structure supporting the presenceof silicate network. For alamarBlue assay, SHED cultured in BG-conditioned medium showed high proliferation rate when subjected to minimal powder content in the DMEM cell culture medium.Hence, it can be concluded that SHED cultured in lower powder content of the BG-conditioned media showedhigh proliferative activity suggesting the potential of the BG for dental usage.
    Matched MeSH terms: Silicon Dioxide
  3. Tailoring the Properties of Metal Oxide Loaded/KCC-1 toward a Different Mechanism of CO2 Methanation by in Situ IR and ESR
    Shahul Hamid MY, Triwahyono S, Jalil AA, Che Jusoh NW, Izan SM, Tuan Abdullah TA
    Inorg Chem, 2018 May 21;57(10):5859-5869.
    PMID: 29746104 DOI: 10.1021/acs.inorgchem.8b00241
    Nickel (Ni), cobalt (Co), and zinc (Zn) loaded on fibrous silica KCC-1 was investigated for CO2 methanation reactions. Ni/KCC-1 exhibits the highest catalyst performance with a CH4 formation rate of 33.02 × 10-2 molCH4 molmetal-1 s-1, 1.77 times higher than that of Co/KCC-1 followed by Zn/KCC-1 and finally the parent KCC-1. A pyrrole adsorption FTIR study reveals shifting of perturbed N-H stretching decreasing slightly with the addition of metal oxide, suggesting that the basic sites of catalyst were inaccessible due to metal oxide deposition. The strengths of basicity were found to follow sthe equence KCC-1, Ni/KCC-1, Zn/KCC-1, and Co/KCC-1. The data were supported by N2 adsorption desorption analysis, where Co/KCC-1 displayed the greatest reduction in total surface area whereas Ni/KCC-1 displayed the least reduction. The elucidation of difference mechanism pathways has also been studied by in situ IR spectroscopy studies to determine the role of different metal oxides in CO2 methanation. It was discovered that Ni/KCC-1 and Co/KCC-1 follow a dissociative mechanism of CO2 methanation in which the CO2 molecule was dissociated on the surface of the metal oxide before migration onto the catalyst surface. This was confirmed by the evolution of a peak corresponding to carbonyl species (COads) on a metal oxide surface in FTIR spectra. Zn/KCC-1, on the other hand, showed no such peak, indicating associative methanation pathways where a hydrogen molecule interacts with an O atom in CO2 to form COads and OH. These results offers a better understanding for catalytic studies, particularly in the field of CO2 recycling.
    Matched MeSH terms: Silicon Dioxide
  4. Fulltext FEM Analysis of Sezawa Mode SAW Sensor for VOC Based on CMOS Compatible AlN/SiO₂/Si Multilayer Structure
    Aslam MZ, Jeoti V, Karuppanan S, Malik AF, Iqbal A
    Sensors (Basel), 2018 May 24;18(6).
    PMID: 29882929 DOI: 10.3390/s18061687
    A Finite Element Method (FEM) simulation study is conducted, aiming to scrutinize the sensitivity of Sezawa wave mode in a multilayer AlN/SiO₂/Si Surface Acoustic Wave (SAW) sensor to low concentrations of Volatile Organic Compounds (VOCs), that is, trichloromethane, trichloroethylene, carbon tetrachloride and tetrachloroethene. A Complimentary Metal-Oxide Semiconductor (CMOS) compatible AlN/SiO₂/Si based multilayer SAW resonator structure is taken into account for this purpose. In this study, first, the influence of AlN and SiO₂ layers’ thicknesses over phase velocities and electromechanical coupling coefficients (k²) of two SAW modes (i.e., Rayleigh and Sezawa) is analyzed and the optimal thicknesses of AlN and SiO₂ layers are opted for best propagation characteristics. Next, the study is further extended to analyze the mass loading effect on resonance frequencies of SAW modes by coating a thin Polyisobutylene (PIB) polymer film over the AlN surface. Finally, the sensitivity of the two SAW modes is examined for VOCs. This study concluded that the sensitivity of Sezawa wave mode for 1 ppm of selected volatile organic gases is twice that of the Rayleigh wave mode.
    Matched MeSH terms: Silicon Dioxide
  5. Sealants revisited: An efficacy battle between the two major types of sealants - A randomized controlled clinical trial
    Prathibha B, Reddy PP, Anjum MS, Monica M, Praveen BH
    Dent Res J (Isfahan), 2019 2 13;16(1):36-41.
    PMID: 30745917
    Background: The aim of this study is comparing the retention and caries preventive effect of the glass-ionomer fissure sealant and resin-based fissure sealant.

    Materials and Methods: A randomized-controlled split-mouth study was conducted to compare the retention and the caries preventive effect of light-cured resin-based sealant (3M ESPE) and glass ionomer sealant (Fuji VII). The sealants were applied to either the right or the left lower mandibular molars (7-9 yrs of age) in 120 school children, based on the randomization process. They were recalled for assessment of clinical retention at intervals of 3, 6, and 12 months. The caries-preventive effect between the two materials was tested statistically by the McNemar's test for matched pairs, and the differences observed with regard to the retention of the materials was tested by Chi-square tests. The level of significance was set to be at P < 0.05.

    Results: At the end of 12th month, sealant retention is found to be higher in the resin-based sealant group compared to the glass ionomer group. In the glass ionomer sealants placed, 101 (91%) were caries-free and 10 (9%) had caries. In the resin-based sealant, 105 (94.60%) had sound teeth and 6 (5.4%) had dental caries (P = 0.34).

    Conclusion: The glass ionomer sealant was less retentive when compared to resin sealants. The caries incidence between the glass ionomer and resin-based sealants was not statistically significant.

    Matched MeSH terms: Silicon Dioxide
  6. Membrane distillation of saline and oily water using nearly superhydrophobic PVDF membrane incorporated with SiO2 nanoparticles
    Hamzah N, Nagarajah M, Leo CP
    Water Sci Technol, 2018 Dec;78(12):2532-2541.
    PMID: 30767918 DOI: 10.2166/wst.2019.016
    Fat, oil and grease in wastewater generated from household kitchens, restaurants and food processing plants affect sewer systems, water resources and environment adversely. Hence, membrane distillation of saline and oily water was studied using a nearly superhydrophobic membrane developed in this work. Polyvinylidene fluoride (PVDF) membrane incorporated SiO2 nanoparticles was synthesized via phase inversion with dual baths and modified using hexadecyltrimethoxy silane. The volume ratio of silane to ethanol was varied between 1:200 to 1:25. The membrane characteristics were examined using a goniometer, a porometer, scanning electron microscopy (SEM) and Fourier transform infrared spectroscopy (FTIR). The PVDF-SiO2 membrane modified using the volume ratio of 1:50 achieved the highest water contact angle of 141.6° and LEP of 2.642 bar. This membrane was further tested in membrane distillation to observe the permeate flux of distilled water, saline solution (1 M NaCl) as well as saline and oily solution (1 M NaCl; 1,000 ppm of palm oil). The modified PVDF/SiO2 showed high permeate flux which is nearly four times of the permeate flux of neat PVDF membrane, but still susceptible of salt and oil fouling as shown in SEM images.
    Matched MeSH terms: Silicon Dioxide
  7. Controlled-growth of ZnO nanowires with different processing temperature
    Yap CC, Muhammad Yahaya, Muhamad Mat Salleh, Dee CF
    Sains Malaysiana, 2008;37:233-237.
    ZnO nanowires have been synthesized using a catalyst-free carbothermal reduction approach on SiO2-coated Si substrates in a flowing nitrogen atmosphere with a mixture of ZnO and graphite as reactants. The collected ZnO nanowires have been characterized by X-ray diffraction, scanning electron microscopy, energy dispersive spectroscopy and photoluminescence spectroscopy. Controlled growth of the ZnO nanowires was achieved by manipulating the reactants heating temperature from 700 to 1000 oC. It was found that the optimum temperature to synthesize high density and long ZnO nanowires was about 800 0C. The possible growth mechanism of ZnO nanowires is also proposed.
    Matched MeSH terms: Silicon Dioxide
  8. Engineering geological properties of oil-contaminated granitic and metasedimentary soils
    Zulfahmi Ali Rahman, Umar Hamzah, Noorulakma Ahmad
    Sains Malaysiana, 2011;40.
    Hydrocarbon is a light-non aqueous phase liquid or known as LNAPL. It poses environmental hazard if accidentally spilled out into the soil and water systems as a result of its insoluble nature in water. LNAPL component infiltrates into soil through pore spaces and afloat at the top of groundwater level. Some of this hydrocarbon would trap and clog within the voids, difficult to remove and costly to clean. The occurence of hydrocarbon in the soil definitely degraded the behaviour of soils in terms of engineering properties. This study aimed to investigate the engineering properties of oil-contaminated soil for two different residual soils originally developed from in-situ weathering of granitic and metasedimentary rocks. The physical characterisations of the soil were determined including particle size distribution, specific gravity test and x-ray diffraction (XRD). The engineering parameters for the contaminated and uncontaminated soils were Atterberg limits, compaction and soil shear strength (UU tests). The amounts of hydrocarbon added to soil were varied at 0%, 4%, 8%, 12% and 16% of dried weigth of soil samples. The results from the particle size distribution analysis showed that residual soil from granitic rock comprises of 38% sand, 33% silt and 4% clay while metasedimentary soil consists of 4% sand, 43% silt dan 29% clay. The mean values of specific gravity for the granitic and metasedimentary soils were 2.56 and 2.61, respectively. The types of minerals present in granitic soil sample were quartz, kaolinite and gibbsite while metasedimentary soil consists of quartz and kaolinite. The Atterberg limits value decreased as a result of increasing amount of added hydrocarbon into the soil. A similar behaviouir was observed with the values of maximum dry density and optimum water content with increasing hydrocarbon content. The overall unconsolidated undrained shear strength, Cu showed a decreasing trend with the increase in hydrocarbon content.
    Matched MeSH terms: Silicon Dioxide
  9. Corrosion protection of carbon steel using polyaniline composite with inorganic pigments
    Al-Dulaimi AA, Shahrir Hashim, Khan M
    Sains Malaysiana, 2011;40:1179-1186.
    Two inorganic pigments (TiO2 and SiO2) were used to prepare composites with polyaniline (PANI) by situ polymerization method. PANI and PANI composites with SiO2 and TiO2 were characterized using Fourier transform infrared spectroscopy and X-ray diffraction. The morphology of the synthesized pigments (PANI , PANI-SiO2 and PANI-TiO2) was examined using scanning electron microscopy. Samples were then used as pigments through blending them with acrylic paint and applied on the surface of carbon steel panels. Corrosion was evaluated for coating of carbon steel panels through full immersion test up to standard ASTMG 31. Mass loss was calculated after they have been exposed in acidic media. A digital camera was also used for monitoring corrosion visually on the surface of carbon steel specimens. The results revealed that acrylic paint pigmented by PANI-SiO2 composite was more efficient in corrosion protection for carbon steel compared with the other synthesized pigments.
    Matched MeSH terms: Silicon Dioxide
  10. Fulltext Efficacy of Several Plants Extracts on the Tunneling Activity and Survival of Subterranean Termites (Coptotermes gestroi and Globitermes sulphureus)
    Bakaruddin NH, Ab Majid AH
    Trop Life Sci Res, 2019 Jan;30(1):33-56.
    PMID: 30847032 MyJurnal DOI: 10.21315/tlsr2019.30.1.3
    This study examined the tunneling activity and the behaviour of two subterranean termites, Globitermes sulphurues and Coptotermes gestroi treated with four plant extracts, namely Pyllanthus niruri, Azadirachta indica, Leucaena leucocephala and Andrographis paniculata. All plants were extracted with three different solvents (methanol, hexane and water) and were diluted into three concentrations (500, 5,000 and 10,000 ppm). A group of 50 workers and 2 soldiers were tested and observed daily during the exposure in order to determine their survivorship and behaviour. Both sections were scored to determine their tunneling activities after seven days. There was a significant difference of tunneling activities of C. gestroi on sand treated with plant extracts (X2(2) = 31.790, p < 0.0001) with a mean rank of 8.50 for methanolic extracts and 32.50 for both hexane and water extracts. Meanwhile, no significant difference was observed on tunneling activity of G. sulphureus on treated sand (X2(2) = 2.200, p = 0.333) with a mean rank of 20.72 for methanolic extracts, 26.31 for water extracts and 26.47 for hexane extracts. Results showed that plants extracted with methanol demonstrated strong repellent properties with 0 tunneling activity on the treated sand and low survivorship of both termites. Moreover, both termites did not survive (0%) when they were treated with methanolic extracts at 10,000 ppm. They also displayed a different behaviour post-exposure such as avoidance, gradually losing the ability to walk and low feeding consumption. These results indicate that there is a strong termiticidal activity of plants extracted with methanol against C. gestroi and G. sulphureus.
    Matched MeSH terms: Silicon Dioxide
  11. Characterization of hydrocarbons in smoke aerosols from burning of three tropical wood species
    Tan hs, Mohd Radzi Abas, Norhayati Mohd Tahir
    Sains Malaysiana, 2016;45:365-371.
    A study has been carried out to characterize hydrocarbons emitted from the burning of three tropical wood species. The woods were burned to ember and smoke aerosols emitted were sampled using high volume sampler fitted with a pre-cleaned glass fibre filters. Hydrocarbons were extracted using ultrasonic agitation with dichloromethane-methanol (3:1 v/v) as solvent and the extracts obtained were then fractionated on silica-alumina column. Detection and quantification of aliphatic and polycyclic aromatic hydrocarbons (PAHs) compounds were carried out using GC-MS. The results indicated that the major aliphatic hydrocarbons characterized were straight chain n-alkanes in the range of C12-C35 with Cmax in the range of C27-C33. Rhizophora apiculata and Hevea brasiliensis wood smoke exhibited a weak odd to even carbon number predominance with carbon preference index (CPI) values greater than one whereas Melaleuca cajuputi wood smoke aerosols did not exhibit similar pattern with CPI obtained close to one. The results obtained also indicated that burning of these wood resulted in formation of PAHs compounds in their smoke aerosols with predominance of three to four rings PAHs over the two, five and lesser of six rings PAHs. PAH diagnostic ratios calculated except for Flan/(Flan+Py) and Indeno/(Indeno+BgP) were consistent with the ratios suggested for wood combustion source as reported in literatures. In the case of the latter, two diagnostic ratios, the values were generally lower than the range normally reported for wood combustion.
    Matched MeSH terms: Silicon Dioxide
  12. Anticorrosive properties of nano silicate from paddy husk in salt medium
    Norinsan Kamil Othman, Solhan Yahya, Denni Asra Awizar
    Sains Malaysiana, 2016;45:1253-1258.
    Anticorrosive properties of nano silicate from paddy husk in salt medium was investigated via weight loss method, Tafel
    polarization and impedance techniques. Prior to the corrosion test, the silica powder was obtained from burning the
    rice husk and extended with a chemical treatment process. The size of silica powder was characterized via zeta sizer and
    showed the amount of micro silica particle appear more than the nano size particle. Nano silica powder was produced
    from the refluxing process of micro silica to enhance the good properties of silica particle. The corrosion inhibition
    efficiency of nano silicate showed good inhibition with increased in inhibitor concentrations. Weight loss test exhibits
    high inhibition as more than 80% even, immersed in the corrosive medium until 14 days. The nano silicate inhibitor
    affected the anodic reaction as showed by Tafel plot analysis. Impedance results also correlated with other test as shown
    by the large size of Nyquist semicircle which represents as high resistance of charge transfer. The surface morphology
    of inhibited specimen showed a smooth surface after nano silicate inhibitor applied in the NaCl medium as observed
    through scanning electron microscopy (SEM) and energy-dispersive x-ray spectroscopy (EDX).
    Matched MeSH terms: Silicon Dioxide
  13. Clinical and radiographic evaluation of chloramphenicol-tetracycline-zinc eugenol oxide antibiotic paste in pulp treatment
    Jesús Luengo Fereira, Heraclio Reyes Rivas, Luz Elena Carlos Medrano, Iovanna Toscano, Minerva Anaya Alvarez
    Sains Malaysiana, 2018;47:971-976.
    This study has been carried out to evaluate the clinical and radiographic CTZ (Chloramphenicol-Tetracycline-Zinc
    Eugenol Oxide) antibiotic paste in pulpotomies of primary molars. A Quasi-experimental study in 43 primary molars
    of children aged 3 to 7 years. Pulpotomies were performed on the selected patients with the CTZ antibiotic paste. Teeth
    were restored with glass ionomer and preformed steel metal crowns. Clinical and radiographic evaluation was performed
    at 6 and 12 months. SPSS V-19 program for data analysis and chi-square test was used up to 5%. Success rates were
    observed during the evaluation periods of time. 93% (x2
    = 0.446, p>0.05) and 88.4% (x2
    = 0.431, p>0.05) of the clinical form;
    97.7% (x2
    = 0.534, p>0.05) and 93% (x2
    = 0.553, p>0.05) were radiographic, at 6 and 12 months, respectively. The CTZ antibiotic
    paste is an alternative in the treatment of pulpotomy of molars. It provides an antimicrobial effect, decreased operative time, without
    causing trauma to the pediatric patient.
    Matched MeSH terms: Silicon Dioxide
  14. Fulltext Nanoparticles in Construction Materials and Other Applications, and Implications of Nanoparticle Use
    Mohajerani A, Burnett L, Smith JV, Kurmus H, Milas J, Arulrajah A, et al.
    Materials (Basel), 2019 Sep 20;12(19).
    PMID: 31547011 DOI: 10.3390/ma12193052
    Nanoparticles are defined as ultrafine particles sized between 1 and 100 nanometres in diameter. In recent decades, there has been wide scientific research on the various uses of nanoparticles in construction, electronics, manufacturing, cosmetics, and medicine. The advantages of using nanoparticles in construction are immense, promising extraordinary physical and chemical properties for modified construction materials. Among the many different types of nanoparticles, titanium dioxide, carbon nanotubes, silica, copper, clay, and aluminium oxide are the most widely used nanoparticles in the construction sector. The promise of nanoparticles as observed in construction is reflected in other adoptive industries, driving the growth in demand and production quantity at an exorbitant rate. The objective of this study was to analyse the use of nanoparticles within the construction industry to exemplify the benefits of nanoparticle applications and to address the short-term and long-term effects of nanoparticles on the environment and human health within the microcosm of industry so that the findings may be generalised. The benefits of nanoparticle utilisation are demonstrated through specific applications in common materials, particularly in normal concrete, asphalt concrete, bricks, timber, and steel. In addition, the paper addresses the potential benefits and safety barriers for using nanomaterials, with consideration given to key areas of knowledge associated with exposure to nanoparticles that may have implications for health and environmental safety. The field of nanotechnology is considered rather young compared to established industries, thus limiting the time for research and risk analysis. Nevertheless, it is pertinent that research and regulation precede the widespread adoption of potentially harmful particles to mitigate undue risk.
    Matched MeSH terms: Silicon Dioxide
  15. Fulltext Development of Nano-SiO2 and Bentonite-Based Mortars for Corrosion Protection of Reinforcing Steel
    Karunarathne VK, Paul SC, Šavija B
    Materials (Basel), 2019 Aug 17;12(16).
    PMID: 31426501 DOI: 10.3390/ma12162622
    In this study, the use of nano-silica (nano-SiO2) and bentonite as mortar additives for combating reinforcement corrosion is reported. More specifically, these materials were used as additives in ordinary Portland cement (OPC)/fly ash blended mortars in different amounts. The effects of nano-silica and bentonite addition on compressive strength of mortars at different ages was tested. Accelerated corrosion testing was used to assess the corrosion resistance of reinforced mortar specimens containing different amounts of nano-silica and bentonite. It was found that the specimens containing nano-SiO2 not only had higher compressive strength, but also showed lower steel mass loss due to corrosion compared to reference specimens. However, this was accompanied by a small reduction in workability (for a constant water to binder ratio). Mortar mixtures with 4% of nano-silica were found to have optimal performance in terms of compressive strength and corrosion resistance. Control specimens (OPC/fly ash mortars without any additives) showed low early age strength and low corrosion resistance compared to specimens containing nano-SiO2 and bentonite. In addition, samples from selected mixtures were analyzed using scanning electron microscopy (SEM) and energy-dispersive X-ray spectroscopy (EDX). Finally, the influence of Ca/Si ratio of the calcium silicate hydrate (C-S-H) in different specimens on the compressive strength is discussed. In general, the study showed that the addition of nano-silica (and to a lesser extent bentonite) can result in higher strength and corrosion resistance compared to control specimens. Furthermore, the addition of nano-SiO2 can be used to offset the negative effect of fly ash on early age strength development.
    Matched MeSH terms: Silicon Dioxide
  16. Fulltext Physicochemical characteristics and photocatalytic performance of TiO2/SiO2 catalyst synthesized using biogenic silica from bamboo leaves
    Fatimah I, Prakoso NI, Sahroni I, Musawwa MM, Sim YL, Kooli F, et al.
    Heliyon, 2019 Nov;5(11):e02766.
    PMID: 31844705 DOI: 10.1016/j.heliyon.2019.e02766
    In this work, TiO2/SiO2 composite photocatalysts were prepared using biogenic silica extracted from bamboo leaves and titanium tetraisopropoxide as a titania precursor via a sol-gel mechanism. A study of the physicochemical properties of materials as a function of their titanium dioxide content was conducted using Fourier transform infrared spectroscopy, a scanning electron microscope, a diffuse reflectance ultraviolet-visible (UV-vis) spectrophotometer, and a gas sorption analyzer. The relationship between physicochemical parameters and photocatalytic performance was evaluated using the methylene blue (MB) photocatalytic degradation process under UV irradiation with and without the addition of H2O2 as an oxidant. The results demonstrated that increasing the TiO2 helps enhance the parameters of specific surface area, the pore volume, and the particle size of titanium dioxide, while the band gap energy reaches a maximum of 3.21 eV for 40% and 60% Ti content. The composites exhibit photocatalytic activity with the MB degradation with increasing photocatalytic efficiency since the composites with 40 and 60% wt. of TiO2 demonstrated the higher degradation rate compared with TiO2 in the presence and absence of H2O2. This higher rate is correlated with the higher specific surface area and band gap energy compared with those of TiO2.
    Matched MeSH terms: Silicon Dioxide
  17. Geochemical fractionation of hazardous elements in fresh and drilled weathered South African coal fly ashes
    Akinyemi SA, Gitari WM, Thobakgale R, Petrik LF, Nyakuma BB, Hower JC, et al.
    Environ Geochem Health, 2020 Sep;42(9):2771-2788.
    PMID: 31900823 DOI: 10.1007/s10653-019-00511-3
    The chemical reactions of dry-disposed ash dump, ingressed oxygen, carbon dioxide, and infiltrating rainwater affect mineralogical transformation, redistribution, and migration of chemical species. Composite samples of weathered coal fly ash taken at various depths and fresh coal fly ash were examined using organic petrographic, X-ray diffraction, X-ray fluorescence techniques, and successive extraction procedures. Results obtained show relative enrichment of glass, Al-Fe-oxides, calcite, and tridymite in the weathered CFA, but the fresh CFA is enriched in mullite, inertinite, maghemite, and ettringite. The enrichment of the weathered CFA in amorphous glass suggests higher reactivity when compared to fresh CFA. The evident depletion of soluble oxides in the weathered CFA is attributed to flushing of the soluble salts by percolating rainwater. Comparative enrichment of examined elements in water-soluble, exchangeable, reducible, and residual fractions of the weathered CFA is partly due to the slow release of adsorbed chemical species from the alumina-silicate matrix and diffusion from the deeper sections of the particles of coal fly ash. Sodium and potassium show enrichment in the oxidisable fraction of fresh CFA. The estimated mobility factor indicates mobility for Ca, Mg, Na, Se, Mo, and Sb and K, Sr, V, Cu, Cr, Se, and B in fresh and weathered CFAs, respectively.
    Matched MeSH terms: Silicon Dioxide
  18. Effect of extraction methods on the molecular structure and thermal stability of kenaf (Hibiscus cannabinus core) biomass as an alternative bio-filler for rubber composites
    Mohamad Aini NA, Othman N, Hussin MH, Sahakaro K, Hayeemasae N
    Int J Biol Macromol, 2020 Jul 01;154:1255-1264.
    PMID: 31765744 DOI: 10.1016/j.ijbiomac.2019.10.280
    Lignin from kenaf (Hibiscus cannabinus) core was investigated as an alternative filler for rubber. Three types of extraction methods were used to isolate lignin from kenaf, namely kraft, soda and organosolv process. The particle size, surface area, functionalities changes, molecular weight and thermal properties of the lignin were characterized. The results showed that Kraft lignin (KL) has the smallest particle size (40.41 μm) compared to soda lignin (SL) (63.85 μm) and organosolv lignin (OL) (66.85 μm). This is in good agreement with the BET surface area of 9.52 m2/g, 1.25 m2/g and 2.40 m2/g respectively. However, the smaller surface area of SL compared to OL is due to the smaller pore size and pore volume of SL. KL also showed high hydroxyl content with corresponding high thermal stability as confirmed by NMR and TGA. The thermal stability of the lignin correlates well with the molecular weight (MW). From the overall characteristics, it can be concluded that KL, SL and OL can be used as an alternative filler in rubber compounds to substitute common fillers like silica and carbon.
    Matched MeSH terms: Silicon Dioxide
  19. New effective 3-aminopropyltrimethoxysilane functionalized magnetic sporopollenin-based silica coated graphene oxide adsorbent for removal of Pb(II) from aqueous environment
    Hassan AM, Wan Ibrahim WA, Bakar MB, Sanagi MM, Sutirman ZA, Nodeh HR, et al.
    J Environ Manage, 2020 Jan 01;253:109658.
    PMID: 31666209 DOI: 10.1016/j.jenvman.2019.109658
    A new effective adsorbent, 3-aminopropyltrimethoxysilane functionalized magnetic sporopollenin (MSp@SiO2NH2) based silica-coated graphene oxide (GO), (GO@SiO2-MSp@SiO2NH2) was successfully synthesized and applied for the first time in the removal of hazardous Pb(II) ions from aqueous solution. The properties of the composite were characterized using Fourier-transform infrared spectroscopy (FTIR), thermogravimetric analysis (TGA), field emission scanning electron microscopy (FESEM), energy-dispersive X-ray spectroscopy (EDX) and vibrating-sample magnetometery (VSM). Evaluation of GO@SiO2-MSp@SiO2NH2 adsorption performance at optimum conditions revealed that the adsorbent has a maximum adsorption capacity of 323.5 mg/g for Pb(II) using 50-200 mg/L initial Pb(II) ions concentrations. Initial and final concentrations of Pb(II) ions in aqueous solution were analyzed using graphite furnace atomic absorption spectroscopy (GF-ASS). The adsorption behavior of Pb(II) ions onto GO@SiO2-MSp@SiO2NH2 was studied using Langmuir, Freundlich and Temkin isotherms models. The values of coefficient of determination showed that the adsorption best fitted the Langmuir model (R2 = 0.9994). Kinetic studies suggested that the adsorption of Pb(II) ion followed a pseudo-second-order rate model (R2 = 1.00) and thermodynamic studies revealed that the adsorption process is endothermic and spontaneous. The effect of co-existing ions on Pb(II) ion adsorption were also studied and found to have considerable effects only at higher matrix concentration. The adsorbent can be reused up to ten times and retain its good adsorption capacity. In addition, GO@SiO2-MSp@SiO2NH2 showed great potential for Pb(II)removal from industrial wastewater samples.
    Matched MeSH terms: Silicon Dioxide
  20. Friction at nanopillared polymer surfaces beyond Amontons' laws: Stick-slip amplitude coefficient (SSAC) and multiparametric nanotribological properties
    Ishak MI, Dobryden I, Martin Claesson P, Briscoe WH, Su B
    J Colloid Interface Sci, 2021 Feb 01;583:414-424.
    PMID: 33011410 DOI: 10.1016/j.jcis.2020.09.038
    Frictional and nanomechanical properties of nanostructured polymer surfaces are important to their technological and biomedical applications. In this work, poly(ethylene terephthalate) (PET) surfaces with a periodic distribution of well-defined nanopillars were fabricated through an anodization/embossing process. The apparent surface energy of the nanopillared surfaces was evaluated using the Fowkes acid-base approach, and the surface morphology was characterized using scanning electron microscope (SEM) and atomic force microscope (AFM). The normal and lateral forces between a silica microparticle and these surfaces were quantified using colloidal probe atomic force microscopy (CP-AFM). The friction-load relationship followed Amonton's first law, and the friction coefficient appeared to scale linearly with the nanopillar height. Furthermore, all the nanopillared surfaces showed pronounced frictional instabilities compared to the smooth sliding friction loop on the flat control. Performing the stick-slip amplitude coefficient (SSAC) analysis, we found a correlation between the frictional instabilities and the nanopillars density, pull-off force and work of adhesion. We have summarised the dependence of the nanotribological properties on such nanopillared surfaces on five relevant parameters, i.e. pull-off force fp, Amontons' friction coefficient μ, RMS roughness Rq, stick-slip amplitude friction coefficient SSAC, and work of adhesion between the substrate and water Wadh in a radar chart. Whilst demonstrating the complexity of the frictional behaviour of nanopillared polymer surfaces, our results show that analyses of multiparametric nanotribological properties of nanostructured surfaces should go beyond classic Amontons' laws, with the SSAC more representative of the frictional properties compared to the friction coefficient.
    Matched MeSH terms: Silicon Dioxide
Related Terms
Filters
Contact Us

Please provide feedback to Administrator (afdal@afpm.org.my)

External Links