METHODS: Thermomechanical damage-maximum bone temperature, osteonecrosis diameter, osteonecrosis depth, maximum thrust force, and torque-were calculated using the finite element method under various margin heights (0.05-0.25 mm) and widths (0.02-0.26 mm). The simulation results were validated with experimental tests and previous research data.
RESULTS: The effect of margin height in increasing the maximum bone temperature, osteonecrosis diameter, and depth were at least 19.1%, 41.9%, and 59.6%, respectively. The thrust force and torque are highly sensitive to margin height. A higher margin height (0.21-0.25 mm) reduced the thrust force by 54.0% but increased drilling torque by 142.2%. The bone temperature, osteonecrosis diameter, and depth were 16.5%, 56.5%, and 81.4% lower, respectively, with increasing margin width. The minimum thrust force (11.1 N) and torque (41.9 Nmm) were produced with the highest margin width (0.26 mm). The margin height of 0.05-0.13 mm and a margin width of 0.22-0.26 produced the highest sum of weightage.
CONCLUSIONS: A surgical drill bit with a margin height of 0.05-0.13 mm and a margin width of 0.22-0.26 mm can produce minimum thermomechanical damage in cortical bone drilling. The insights regarding the suitable ranges for margin height and width from this study could be adopted in future research devoted to optimizing the margin of the existing surgical drill bit.
PURPOSE: The purpose of this in vitro study was to evaluate the SR, tensile strength (TS), and percentage elongation (% E) of different SEs subjected to outdoor weathering in the Malaysian climate.
MATERIAL AND METHODS: Type-II dumbbell-shaped specimens (N-120) (nonweathered=15, weathered=15) were made from 3 room-temperature vulcanized (A-2000, A-2006, and A-103) and 1 heat-temperature vulcanized (M-511) silicone (Factor II). For 6 months, weathered specimens were subjected to outdoor weathering inside a custom exposure rack. Simultaneously, the nonweathered specimens were kept in a dehumidifier. Subsequently, the SR was measured with a profilometer; TS and % E were measured by using a universal testing machine. Two-way ANOVA was used to compare the means of the tested properties of the nonweathered and weathered specimens, and pairwise comparison was carried out between the silicones (α=.05).
RESULTS: After outdoor weathering, the SR, TS, and % E were adversely affected by weathering in the Malaysian environment. Among the silicone materials, A-2000 showed the least TS changes (2.51 MPa), while A-2006 demonstrated significant changes in percentage elongation after outdoor weathering (266.5%). M-511 exhibited the highest mean value (2.50 μm) for SR changes. In addition, A-103 SE showed statistically significant differences in most pairwise comparisons for all 3 dependent variables.
CONCLUSIONS: Based on the evaluation of mechanical properties, A-103 can be suggested as a suitable silicone for maxillofacial prostheses fabricated for tropical climates. However, A-2000 can be a suitable alternative, although significant changes to surface roughness were detected after outdoor weathering.
METHODS: To verify this hypothesis, a computational model was developed to simulate the thermochemical processes involved during TCA with sequential injection. Four major processes that take place during TCA were considered, i.e., the flow of acid and base, their neutralisation, the release of exothermic heat and the formation of thermal damage inside the tissue. Equimolar acid and base at 7.5 M was injected into the tissue intermittently. Six injection intervals, namely 3, 6, 15, 20, 30 and 60 s were investigated.
RESULTS: Shortening of the injection interval led to the enlargement of coagulation volume. If one considers only the coagulation volume as the determining factor, then a 15 s injection interval was found to be optimum. Conversely, if one places priority on safety, then a 3 s injection interval would result in the lowest amount of reagent residue inside the tissue after treatment. With a 3 s injection interval, the coagulation volume was found to be larger than that of simultaneous injection with the same treatment parameters. Not only that, the volume also surpassed that of radiofrequency ablation (RFA); a conventional thermal ablation technique commonly used for liver cancer treatment.
CONCLUSION: The numerical results verified the hypothesis that shortening the injection interval will lead to the formation of larger thermal coagulation zone during TCA with sequential injection. More importantly, a 3 s injection interval was found to be optimum for both efficacy (large coagulation volume) and safety (least amount of reagent residue).